Anton Bauer MATRIX Users Guide

One World. One Smart Choice.

Approved Copy

®

™

MATRIX

Cheese Plate

Owner’s Manual

Read Before Using

A7595-0405 Rev B

TABLE OF CONTENTS

Approved Copy

1 TYPICAL SETUP ON 15/19mm RODS

2 OPTIONAL LAYOUT FOR MATRIX CHEESE PLATE

3 MOUNTING ELIPZ® 10K BATTERY

TYPICAL SETUP ON 15/19mm RODS

Approved Copy

1. Loosely fasten Spacer Bar to Clamps

2. Slide Clamps onto Rails

3. Secure Clamps in desired location and clamp in place with lever

4. Tighten screws in Spacer Bar using 10-32 x 3/8 screw

15/19 mm Studio Location

15 mm Lightweight Location

10-32 x 3/8 screw

Spacer Bar

15/19 mm Clamps

Rails (not supplied)

Clamp lever

1. Install MATRIX Cheese Plate to Spacer Bar using 1/4-20 x 1/2 Flat Head Cap Screws.

2. OPTIONAL- Install AJA Ki-Pro Mini using 10-32 x 3/8 screws.

3. Install proper GOLD MOUNT® Bracket using M3 x 12mm Pan Head Screws. (standard with your Gold Mount).

NOTE: MATRIX Cheese Plate has 1/4-20 & 3/8-16 tapped holes for various accessory mounting.

AJA Ki-Pro Mini Mounting Plate (not supplied)

MATRIX Cheese Plate

10-32 x 3/8 screw

Gold Mount (not supplied)

1/4-20 x 1/2 Flat Head Cap Screw

M3 x 12 mm Pan Head Screw

1

OPTIONAL MOUNTING OPTIONS FOR MATRIX CHEESE PLATE

Approved Copy

A

B C

2

CLAMP LEVER FEATURE

Approved Copy

For proper positioning of Clamp Lever

The most practical mounting for

• Once lever has been tightened in
place, pull out lever and position
lever as needed.

the lever is straight up.

MOUNTING ELIPZ 10K BATTERY

1. See picture below for mounting ElipZ 10K battery.

ElipZ 10K battery shoe
mount.

1/4-20 hole for mounting
ElipZ 10K battery shoe
Mount.

ElipZ 10K battery

2. MATRIX Cheese Plate can be mounted in different positions. See page 2 for details.

3. The proper ElipZ power cable is required to power the camera.

3

The following are trademarks of Anton/Bauer, Inc.:

Approved Copy

Anton/Bauer, Anton/Bauer logo and parallelogram design, Aspekt, Automatique,

DataTap, DIONIC, Elipz, Egripz, Elightz, Essentialz, Gold Mount, HubZ, HyTRON, Impac,

Interactive and design, LifeSaver, Logic Series, Logic Series Logo, Maxx man logo design,

Nexus, PowerStrap, Proformer, Probe, ProPac, RealTime, Satellight, Snap-On, Stasis, Stasis

Flex, Tandem, TrimPac, Ultrakit, Ultralight, “One World. One Smart Choice”, “The power

behind the best cameras capturing the best images in the world.”, “The quality standard

of the video industry”, “The worldwide standard”, and “There should always be choices. It

makes it easier to recognize the best.”

Lexan is a registered trademark of G.E. Company Corp.

Cordura is a registered trademark of E.I. duPont de Nemours

Anton/Bauer, Inc.

World Headquarters

14 Progress Drive, Shelton, CT U.S.A.

Tel [phone] or [phone]

Fax [phone]

[e-mail]

Anton/Bauer

A Vitec Group brand

Anton/Bauer Europe, B.V.

Eurode Business Center, Eurode - Park 1-2

6461KB Kerkrade, The Netherlands

Tel [phone]

Fax [phone]

[e-mail]

www.antonbauer.com

Anton/Bauer, Inc. - Signapore Oce

6 New Industrial Road, # 02-02 Hoe

Huat Ind. Bld., Singapore 536199

Tel [phone]

Fax [phone]

[e-mail]