372XXA Series Vector
Network Analyzer
GPIB QUICK REFERENCE GUIDE
This manual supplements the 372XXA Series Vector Network
Analyzer Programming Manual. Insert it behind the tab marked
Appendix C, GPIB Quick Reference Guide in that manual.
P/N: 10410-00164
COPYRIGHT 1995 WILTRON CO.
PRINTED: JULY 1995
REVISION: C
WARRANTY
The WILTRON product(s) listed on the title page is (are) warranted against defects in
materials and workmanship for one year from the date of shipment, except for YIG-tuned
oscillators, which are warranted for two years.
WILTRON’s obligation covers repairing or replacing products which prove to be defective
during the warranty period. Buyers shall prepay transportation charges for equipment
returned to WILTRON for warranty repairs. Obligation is limited to the original purchaser.
WILTRON is not liable for consequential damages.
LIMITATION OF WARRANTY
The foregoing warranty does not apply to WILTRON connectors that have failed due to normal
wear. Also, the warranty does not apply to defects resulting from improper or inadequate
maintenance by the Buyer, unauthorized modification or misuse, or operation outside of the
environmental specifications of the product. No other warranty is expressed or implied, and
the remedies provided herein are the Buyer’s sole and exclusive remedies.
NOTICE
WILTRON Company has prepared this manual for use by WILTRON Company personnel and
customers as a guide for the proper installation, operation and maintenance of WILTRON
Company equipment and computer programs. The drawings, specifications, and information
contained herein are the property of WILTRON Company, and any unauthorized use or
disclosure of these drawings, specifications, and information is prohibited; they shall not be
reproduced, copied, or used in whole or in part as the basis for manufacture or sale of the
equipment or software programs without the prior written consent of WILTRON Company.
372XXA VNA GPIB
Quick Reference Guide
Table of Contents
1. INTRODUCTION . . . . . . . . . . . . . . . . . . . 3
2. GENERAL . . . . . . . . . . . . . . . . . . . . . . . 3
1.
INTRODUCTION
2.
GENERAL
372XXA VNA GPIB
Quick Reference Guide
This appendix prov ides a quick refer ence to the 372XXA GPIB Programming commands.
This guide is divided into two listings. Table 1 (beg innin g on page 4)
provides an alp habe tical li sting of all 372XXA commands. These commands are also listed alphabetic ally and fully describe d in th e 372XXA
Programming Manual, Chapter 10.
Table 2 (beginning on page 33) prov ides a command listing that is divided into function al gr oups. Th ese co mmand s are func tion ally
grouped — and furth er descr ibed as a group — in Chapters 4 thr u 9 of
the 372XXA Programmin g Man ual. This table is organized in chapter
sequence; that is, Chapter 1 groups are follo wed by Chap ter 2 grou ps,
etc.
372XXA GPIB PM 3
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Code s ( Mnemonics)
Command Description Functional Group
*CLS Clear status bytes and stru ct ure s IEEE-488.2, Cha pter 7
*DDT Define device trigge r comm and IEEE-488.2, Cha pt er 7
*DDT? Define device trigge r query IEEE-488.2, Chapter 7
*ESE Standard Event Statu s Enable Comm and IEEE-488.2, Cha pt er 7
*ESE? Standard Event Status Enable query IEEE-488.2, Chapter 7
*ESR? Standard Event Statu s Register query IEEE-488.2, Chapter 7
*IDN? Instrument ident ifica tion query IEEE-488.2, Cha pt er 7
*IST? Ist messag e Sta tu s query IEEE-488.2, Cha pt er 7
*OPC Operation Complet e Com m and IEEE-488.2, Chapt er 7
*OPC? Operation Com plet e query IEEE-488.2, Cha pt er 7
*OPT? Options installed quer y IEEE-488.2, Chapter 7
*PRE Parallel Poll Register Enable IEEE-488.2, Chapter 7
*PRE? Parallel Poll Register Enable query IEEE-488.2, Chapter 7
*RST Reset Command IEEE-488.2, Chapt er 7
*SRE Service Request Enab le IEEE-488.2, Cha pt er 7
*SRE? Service Request Enable query IEEE-488.2, Cha pt er 7
*STB? Status Byte query IEEE-488.2, Chapter 7
*TRG Group Execute Trigger equivalen t com ma nd IEEE-488.2, Chapt er 7
*TST? Self test and query IEEE-488.2, Chapter 7
*WAI Wait to Continue IEEE-488.2, Chapter 7
A12 Simulate 12-te rm calibration Calibration, Chapter 5
A8R Simulate 1-pat h 2-p ort calibr atio n rev ers e path Calibration, Chapter 5
A8T Sim ulat e 1-p ath 2-p ort calibr at ion fo rwar d path Calibration, Chapter 5
ABT Simulate trans freq re spon se calibr at ion fo rwar d and reve rse Calibration, Chapter 5
ADD Select addition as Trace Math for active c hann el Display , Chapter 4
AFT Simulate trans freq response calibr atio n forwar d pat h Calibration, Chapter 5
AH0 Tur n autom at ic DU T protec tion off Measurement , Chapter 4
AH1 Tur n autom at ic DU T protec tion on Measurement , Chapter 4
AHX? Output automatic D U T protect ion onoff status Measurem ent, Chapter 4
ALC Perform AL C loop inte rna l calibr at ion Diagnostics , Chapt er 8
AMKR Select active marker on all channels ma rker mode Markers, Chapter 6
ANNCOL Enter the color number for anno tation and m enu text System State, Chapt er 8
4 372XXA GPIB PM
ALPHABETICAL LISTING GPIB QUICK
OF PROGRAMMING CODES REFERENCE GUIDE
Table 1. Alphabetical Listing of Programming Code s ( Mnemonics)
Command Description Functional Group
ANNCOL? Annotation and menu text color numbe r query System State, Chapt er 8
AOF Turn averaging off Enhancement , Chapter 4
AOF? Output averaging on/of f sta tus Enhan cem ent , Chapt er 4
AON Turn aver aging on Enhancement , Chapter 4
APR Enter Group delay aperture setting on ac tive chann e l Display , Chap ter 4
APR? Output group delay apertur e setting on active ch anne l Display , Chapter 4
ARB Simulate reflection only cal ibration b o th ports Calibration, Chapter 5
ARF Sim ulat e reflect ion on ly calibrat ion po rt 1 Calibration, Chapter 5
ARR Simulate reflect ion on ly calibrat ion po rt 2 Calibration, Chapter 5
ART Sim ulat e trans freq respon se calibr at ion rev ers e pat h Calibration, Chapter 5
ASC Autoscale the active channe l display Display, Chap ter 4
ASP Set polar stop swee p position ang le Display , Chapte r 4
ASP? Output polar stop sweep position angle Display , Chap ter 4
AST Set polar start swee p position angle Display, Chapter 4
AST? Output polar start sweep position angle Display , Chapter 4
ATTN Attach next segment and make the act ive seg me nt Limits, Chapter 6
AVG Turn on Averaging and set t o value Enhancement, Chapter 4
AVG? Output Averaging count Enhancement, Chapt er 4
BBL Select broadband load for calibration Calibrat ion, Chap te r 5
BBZ Enter broadba nd load im peda nce f or ca librati on Calibration, Chapter 5
BC0 Tur n CRT disp la y off System State , Chapt er 8
BC1 Turn C RT disp lay on System State, Cha pt er 8
BCX? Output CR T display stat us System State , Cha pt er 8
BD1 Select band 1 for definition Multiple Sour ce Control, Chapt er 9
BD2 Select band 2 for definition Multiple Sour ce Control, Chapt er 9
BD3 Select band 3 for definition Multiple Sour ce Control, Chapt er 9
BD4 Select band 4 for definition Multiple Sour ce Control, Chapt er 9
BD5 Select band 5 for definition Multiple Sour ce Control, Chapt er 9
BEG Begin taking calibration data Calibration, Chapter 5
BEGN Begin next segme n t and ma ke the act ive se gm ent Limits, Chapter 6
BH0 Turn bias of f while in Hold Measurement, Chapter 4
BH1 Turn bias on while in Hold Measurem ent, Chapter 4
372XXA GPIB PM 5
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Code s ( Mnemonics)
Command Description Functional Group
BHX? Output bias on/off during Hold status Measurement , Chapter 4
BLU Select blue as third plane color System State, Cha pter 8
BPF Enter break point frequency for 3 line LRL calibration Calibration, Chapter 5
BSP Ent er band stop frequ ency Multiple Source Control, Chapt er 9
BSP? Output band stop frequency Multiple Source Control, Chapter 9
BST Enter band sta rt frequency Multiple Source Con trol, Chapter 9
BST? Output band start frequency Mu ltiple Sour ce Con trol, Chapt er 9
BWL3 Set 3 dB for bandwidt h loss valu e Markers, Chapter 6
BWLS Enter bandwidth loss value Markers, Chapte r 6
BWLS? Output bandwidth loss va lue Markers, Chapter 6
C12 Select 12 term calibration Calibration, Chapter 5
C8R Selec t 1-path 2- por t cal ibration r ever se path Calibration, Chapter 5
C8T Select 1-path 2-port calibration forward pat h Calibration, Chapter 5
CAS Clear active segmented limit vertical/ hor izont al def init io ns Limits, Chapt er 6
CBT Selec t trans freq response cal ibration for ward and rever se Calibration, Chapter 5
CC0 Ent er capacita nce co ef f icient 0 for open Calibration, Chapter 5
CC1 Ent er capacita nce co ef f icient 1 for open Calibration, Chapter 5
CC2 Ent er capacita nce co ef f icient 2 for open Calibration, Chapter 5
CC3 Ent er capacita nce co ef f icient 3 for open Calibration, Chapter 5
CF2 Select female 2.4mm connector for current port Calibration, Chapter 5
CF3 Select female GPC-3.5 connector for current port Calibration, Chapter 5
CFC Select female TNC connector for current port Calibration, Chapter 5
CFK Select fem ale K connect or for curren t port Calibration, Chapter 5
CFN Select female Type N conn ector for current por t Calibration, Chapter 5
CFS Select fem ale SMA connector for curren t port Calibration, Chapter 5
CFT Select trans freq response calibration f or ward path Calibration, Chapter 5
CFV Select fem ale V connect or for curren t port Calibration, Chapter 5
CH1 Select Channel 1 as active chann el Channels, Chapter 4
CH2 Select Channel 2 as active chann el Channels, Chapter 4
CH3 Select Channel 3 as active chann el Channels, Chapter 4
CH4 Select Channel 4 as active chann el Channels, Chapter 4
CHX? Output Active channel Channels, Chapter 4
6 372XXA GPIB PM
ALPHABETICAL LISTING GPIB QUICK
OF PROGRAMMING CODES REFERENCE GUIDE
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
CLB Clear all multiple source ban d def inition s Multiple Source Control, Chapt er 9
CM Sets Distance dat a type an d scales by 1E-2 Data Entry Suf fix es, Chapter 4
CM2 Select male 2.4mm connect or for current por t Calibration, Chapter 5
CM3 Select male GPC-3.5 conne ctor for current por t Calibration, Chapter 5
CMC Select male TNC connector for current po rt Calibration, Chapter 5
CMK Select male K connector for curren t port Calibration, Chapter 5
CMN Select male N connector for current port Calibration, Chapte r 5
CMS Select male SMA connector for curren t port Calibration, Chapter 5
CMT Same as CM Data Entry Suf fix es, Chapt er 4
CMV Select male V connector for curren t port Calibration, Chapter 5
CMX? Output calibrat ion met hod Calibration, Chapter 5
CND Select user specified connector for current port Calibration, Chapter 5
CNG Select GPC-7 connector for current port Calibrat ion, Chapter 5
CNTR Enter center frequency Measurement, Chapt er 4
CNTR? Output center frequen cy Measurement , Chapt er 4
COF Turn Off Vector Error Correction Calibration, Chapter 5
CON Turn On Vector Error Correction Calibration, Chapte r 5
CON? Output error correction on/off status Calibration, Chapter 5
COO Enter offset for open for user specif ied con nect or Calibration, Chapter 5
COS Enter offset for short for user specif ied con nect or Calibration, Chapter 5
CPYALCFH Copy ALC Cal file from floppy t o h ard disk Disk Functions, Chapt er 8
CPYALCHF Copy ALC Cal file from hard to floppy disk Disk Functions, Chapter 8
CPYALLFH Copy Combined Har dwar e Cal file from flo ppy to har d disk Disk Functions, Chapt er 8
CPYALLHF Copy Combined Hardwar e Cal file from hard to flop py disk Disk Functions, Chapter 8
CPYCALFH Cop y Calibration/Front Panel Setup from floppy to hard disk Disk Functions, Chapter 8
CPYCALHF Cop y Calibration/Front Panel Setup from hard to floppy disk Disk Functions, Chapter 8
CPYDATFH Copy Tabular Data file from f loppy t o h ard disk Disk Functions, Chapt er 8
CPYDATHF Copy T abular Data file f rom har d to floppy disk Disk Function s, Chapt er 8
CPYELGFH Copy Error Log file from floppy to har d disk Disk Functions, Chapt er 8
CPYELGHF Copy Error Log file from hard to floppy disk Disk Functions, Chapter 8
CPYFREFH Copy Frequency Cal file from floppy to har d disk D isk Func tion s, Chapter 8
CPYFREHF Copy Frequency Cal file from hard to floppy disk Disk Functions, Chapt er 8
372XXA GPIB PM 7
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
CPYLOGFH Copy Service Log file from floppy to hard disk Disk Functions, Chapter 8
CPYLOGHF Copy Service Log file from hard to floppy disk Disk Functions, Chapter 8
CPYNRMFH Copy Trace Memor y File from floppy to hard disk Disk Functions, Chapter 8
CPYNRMHF Copy Trace Memory File from har d to floppy d is k Disk Functions, Chapter 8
CRB Select reflection only calibrat ion bot h port s Calibration, Chapter 5
CRF Select reflection only calibration port 1 Calibration, Chapter 5
CRR Select reflection only calibration port 2 Calibration, Chapter 5
CRT Select trans freq response calibration rever se pa th Calibration, Chapter 5
CSB Same as *CLS IEEE-488.2, Cha pter 7
CSF? Output cal start frequency Calibration, Chapter 5
CSL Clear service log Diagnostics , Chapt er 8
CTF? Output cal stop frequency Calibration, Chap te r 5
CTN Continue sweeping from cur ren t point Measurement , Chapter 4
CWC Select CW frequency calibration da ta point s Calibration, Chapter 5
CWF Turn CW on and set freq uenc y Measurement, Chapt er 4
CWF? Output CW frequency set Measurem ent, Chapter 4
CWON Turn CW on at last frequency set Measurement, Chapter 4
CWON? Output CW on/off stat us Measurement, Chapter 4
CWP Enter number of points dra wn in CW Measurement, Chapter 4
CWP? Outpu t nu mber of point s drawn in C W Measurement, Chapter 4
CXX? Output calibrat ion type Calibration, Chapter 5
CYN Select cyan as third pla ne color System State, Chapter 8
D13 Select dual channel display, channels 1 & 3 Channels, Chapter 4
D14 Select quad display , all four channels Channels, Chapter 4
D24 Select dual channel display, channels 2 & 4 Channels, Chapter 4
DAT Display data only on active channel Display, Chap ter 4
DAT? Output trace memory display mode Display , Chapter 4
DATCOL Enter the color number for dat a System State, Ch apter 8
DATCOL? Data color numbe r query System State , Cha pter 8
DB Sets Power data type Data Entry Suff ixes, Chapter 4
DBL Same as DB Data Entry Suf fix es, Chapt er 4
DBM Sets Power data type Dat a Ent ry Suf fix es, Chapt er 4
8 372XXA GPIB PM
ALPHABETICAL LISTING GPIB QUICK
OF PROGRAMMING CODES REFERENCE GUIDE
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
DBP Select Distance Bandpass mode for active channel Time Domain, Chapt er 9
DC1 Display channel 1 and 2 operat ing pa ramet ers System Sta te, Cha pt er 8
DC3 Display channel 3 and 4 operat ing pa ramet ers System Sta te, Cha pt er 8
DCA Select Automatic DC t er m calcu lation f or lowpass Tim e Domain, Chapt er 9
DCO Select Open for DC term for lowpass Time Domain, Chapter 9
DCP Same as DCP1 System State, Chapter 8
DCP1 Display Calibration Parameters 1st page System State, Cha pt er 8
DCP2 Display Calibration Parameters 2nd page System State , Cha pt er 8
DCS Select Short for DC term for lowpass Time Domain, Chapt er 9
DCV Enter value for DC term for lowp ass T im e Dom ain, Chapt er 9
DCV? Output lowpass DC term value Time Domain, Chapter 9
DCX? Output lowpass DC term selection Time Domain, Chapter 9
DCZ Select Line Impedance for DC term for lo wpass Time Domain, Chapter 9
DD0 Turn Data drawing off System State , Cha pt er 8
DD1 Turn Data drawing on System State , Cha pt er 8
DD1? Output Data Dr awing on/ off status System State, Chapter 8
DDX? Output active channel dom ain par am et er (frequ ency dista nce or
time)
DEC Same as DELCA L Disk Functions, Chapt er 8
DECH Same as DELCALH Disk Functions, Chapter 8
DED Same as DELD AT Disk Functions, Chapt er 8
DEDH Same as DELDA TH Disk Functions, Chapter 8
DEG Sets Phase data type Data Entry Suf f ixes, Chapter 4
DELALC Delete ALC Cal file from flo ppy disk Disk Functions, Chapter 8
DELALCH Delete ALC Cal file from har d d isk Disk Functions, Chapt er 8
DELALL Delete Combined Hardware Cal file from floppy disk Disk Functions, Chapter 8
DELALLH Delete Combined Hardware Cal file from hard disk D isk Function s, Chapter 8
DELCAL Delete Calibratio n/Fro nt Panel Set up f rom flo ppy disk Disk Function s, Chapt er 8
Time Dom ain, Chapter 9
DELCALH Delete Calibration/Fro nt Panel Setup from hard disk Disk Functions, Chapter 8
DELDAT Delet e Tabular Data file from floppy d is k Disk Functions, Chapt er 8
DELDATH Delete Tabular Data file from hard disk D isk Function s, Chapt er 8
DELELG Delet e Error Log fi le from floppy disk Disk Functions, Chapt er 8
372XXA GPIB PM 9
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
DELELGH Delete Error Log file from hard disk Disk Functions, Chapt er 8
DELFRE Delete Fr equ ency Cal fi le from floppy disk Disk Functions, Chapt er 8
DELFREH Delete Frequency Cal file from hard disk Disk Functions, Chapter 8
DELLOG Delete Service Log file from flo ppy disk Disk Functions, Chapter 8
DELLOG H Delet e Ser vice Lo g file from hard disk Disk Functions, Chapt er 8
DELNRM Delet e Trace Memory File from floppy disk Disk Functions, Chapt er 8
DELNRMH Delete Tra ce Mem ory File from hard disk Disk Functions, Chapter 8
DEN Same as DELNRM Disk Functions, Chapt er 8
DENH Same as DELNRMH Disk Functions, Chapter 8
DF2 Display 2.4mm female connector informat io n System State, Cha pt er 8
DF3 Display GPC-3.5 female conn ect or inform at ion System State, Chapt er 8
DFC Select discrete frequency calibration data points Calibrat ion, Chapter 5
DFD Done specifying discrete freque ncy range s Measurement , Chapter 4
DFK Display K female connect or info rmati on Syst em Sta te , Chapt er 8
DFN Display N female connector informati on System State, Cha pt er 8
DFP Display Fron t panel inst rumen t state System State, Cha pter 8
DFQ Enter Sin gle discr ete frequency Measurement, Chapter 4
DFS Display SMA female connector in fo rmat i on System State, Chapter 8
DFT Display TNC female connector informati on System State, Chapt er 8
DFV Display V female connect or info rmati on System State, Chapter 8
DG7 Display GPC-7 Male connector informat ion System State, Chapter 8
DGS Display GPIB stat us infor ma tion Syst em Sta te , Chapt er 8
DGT Same as DGT 1 Peripheral Tests, Chapter 8
DGT1 Display 1st CRT test pat t ern Peripheral Tests, Chapter 8
DGT2 Display 2nd CRT test pattern Peripheral Tests, Chapter 8
DGT3 Display 3rd CRT te st pat te rn Peripheral Tests, Chapter 8
DIA Select Air as active dielectric Display, Chapter 4
DIE Enter a dielectric va lue Display, Chap ter 4
DIM Select microporous teflon as active die lect ric Display, Chapte r 4
DIP Select polyethylene as active dielectr ic Display , Chapter 4
DIS Display active segmen ted limit Limits, Chapter 6
DIS? Output ac tive segmented lim it on/off sta tus Limits, Chapter 6
10 372XXA GPIB PM
ALPHABETICAL LISTING GPIB QUICK
OF PROGRAMMING CODES REFERENCE GUIDE
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
DIT Select T eflon a s active d ie lect ric D isplay, Chapter 4
DIV Select Division as Trace Mat h for active ch anne l Display , Chapte r 4
DIX? Output dielectric constant Display , Chapte r 4
DLA Select Group Delay display for active channe l Display, Chapter 4
DLP Select Distance lowpass mode for active ch anne l Time Domain, Chapter 9
DM2 Display 2.4mm male connect or inform atio n System State, Chapter 8
DM3 Display GPC-3.5 male conn ector inform atio n System State , Chapt er 8
DMK Display K male connector info rmat ion System State, Chapter 8
DMN Display N male connector information System State, Cha pt er 8
DMS Display SMA m ale connector information System State, Chapter 8
DMT Display TNC male connector info rmat i on System Sta te , Cha pt er 8
DMV Display V male connector info rmat ion System State, Chapter 8
DNM Display data normalized to T race M emor y on a ctive channel Display , Chapte r 4
DPI Select Distance phasor impulse mode for active cha nnel Time Domain, Chapt er 9
DPN Enter pen numb er for data Hard Copy, Chapter 8
DPR0 Visible data only OFD format Remote Only, Chapter 7
DPR1 Data pair always OFD format Remote Only, Chapter 7
DR1 Select Marker 1 as Delta Reference Marker Ma rkers, Chapte r 6
DR2 Select Marker 2 as Delta Reference Marker Ma rkers, Chapte r 6
DR3 Select Marker 3 as Delta Reference Marker Ma rkers, Chapte r 6
DR4 Select Marker 4 as Delta Reference Marker Ma rkers, Chapte r 6
DR5 Select Marker 5 as Delta Reference Marker Ma rkers, Chapte r 6
DR6 Select Marker 6 as Delta Reference Marker Ma rkers, Chapte r 6
DRF Turn Delta reference mode On Markers, Chapter 6
DRL Diagnost ic rea d latch Diagnostics, Chapt er 8
DRO Turn Delta reference mode Of f Markers, Chapter 6
DRO? Output delta refere nce m ode on/of f stat us Markers, Chapter 6
DRX? Output the Delta reference marker Markers, Chapter 6
DSF0 Disable automatic filter shape factor calculation Markers, Chapter 6
DSF1 Enable automat ic filt er shape fact or calculation Marke rs, Chap ter 6
DSFX? Output automa tic f i lter shape fa ctor calc ulat ion enab ledisable st atus Markers, Chapter 6
DSP Select single channel display Channels, Chapter 4
372XXA GPIB PM 11
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
DSP? Output channe l display mode Channels, Chapter 4
DSQ0 Disable automatic filter Q calculation Markers, Chapter 6
DSQ1 Enable automatic filter Q calculation Markers, Chapter 6
DSQX? Output auto ma tic fi lter Q calculat ion ena ble/ disable stat us Markers, Chapter 6
DTM Display Measur em ent data and T race M em ory on a ctiv e channel Display , Chap ter 4
DVM Set DVM channel Diagnostics, Cha pt er 8
DWG Display Waveg uide par amet er s System State, Cha pter 8
DWL Diagnostic write latch Diagnostics , Chapter 8
ECW Select CW operation for componen t being edit ed Multiple Source Control, Chapt er 9
ED1 Edit Source 1 equation Multiple Source Control, Chapt er 9
ED2 Edit Source 2 equation Multiple Source Control, Chapt er 9
EDG End diagnostics mode Diagnostics , Chapt er 8
EDR Edit receiver equati on Multiple Source Con trol, Chapt er 9
EDV Set divisor for equation being edited Multiple Source Control, Chapt er 9
EDV? Output divisor for equation being edite d Multiple Source Control, Chapter 9
EKT External key board test Peripheral Tests, Chapter 8
EML Set multiplier for equation being edited Multiple Source Control, Chapter 9
EML? Output multiplier for equation being ed ited Multiple Source Control, Chapt er 9
EOS Set offs et freque ncy for equat ion be in g edited Multiple Sour ce Con tr ol, Chapt er 9
EOS? Output of fset frequency for equa tion being edited Multiple Source Control, Chapt er 9
ESW Select sweep operation for component being edited Multiple Source Control, Chapt er 9
EXD Display external a/d input Diagnostics, Chapter 8
EXW? Output multiple source swee p flag for equa tion being edited Multiple Source Control, Chapt er 9
FFD Form Feed to Printer/Stop pr int/plot Hard Copy , Chap ter 8
FGT Select frequency with time gate for active chann el Time Domain, Chapt er 9
FHI Same as NP1601 Measurement, Chapt er 4
FIL Fill defined discrete f req uenc y range Measurement, Chapter 4
FLC Source frequency linearity internal calibr at io n Diagnostics, Chapter 8
FLO Same as NP101 Measurement, Chapter 4
FLTBW? Output fi lter band width Markers, Chapter 6
FLTC? Output filter center fr equency Markers, Chapter 6
FLTL? Output filter loss at reference value Markers, Chapter 6
12 372XXA GPIB PM
ALPHABETICAL LISTING GPIB QUICK
OF PROGRAMMING CODES REFERENCE GUIDE
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
FLTQ? Output filter Q Markers, Chapter 6
FLTS? Output filter shape factor Markers, Chapter 6
FMA Select ASCII data transfer format Remote Only, Chapter 7
FMB Select IEEE754 64 bit data transfer format Remote Only, Chapter 7
FMC Select IEEE754 32 bit data transfer format Remote Only , Chapter 7
FME Same as NP4 01 Measurement, Chapter 4
FMKR Select filter parameters marker mode Markers, Chapter 6
FOF Blank frequency informa tion System State , Chapt er 8
FON Display frequency infor ma tion System State, Cha pt er 8
FOX? Output frequency informat ion on /o ff stat us System Sta te, Cha pt er 8
FP0 Turn flat powe r corre ctio n off Measur em ent , Chapt er 4
FP1 Turn flat powe r corre ctio n on Measur ement , Chapt er 4
FPT Front panel keypad test D iagnos tics , Cha pt er 8
FPX? Output flat power corr ection on/off status Measurem ent, Chapter 4
FQD Select Frequency Doma in for active cha nnel T im e Domain, Chapt er 9
FRC Clear all defined discrete frequency ranges Measurement, Chapter 4
FRI Set discrete frequency fill rang e incre me nt frequency Measurement , Chapt er 4
FRP Set discrete frequency fill range number of points Measurement, Chapter 4
FRS Set discrete frequency fill range start frequenc y Measurement, Chapt er 4
GCT Enter gate cen ter value time or distan ce Time Domain, Chapter 9
GCT? Output gate center value Time Domain, Chapter 9
GDS Gate symbols displayed on active channe l Time Domain, Chapter 9
GHZ Sets Frequency data type and scales by 1E9 Dat a Ent ry Suffixes, Chapter 4
GLS Select low sidelobe gate shape Time Domain, Chapter 9
GMS Select minimum sidelobe gate shape Time Domain, Chapt er 9
GNM Select nominal gate shape T ime Domain, Chapter 9
GOF Turn Off Gating on active channel Time Dom ain, Chapter 9
GOF? Output gating mode on active channe l Tim e Dom ain, Chapt er 9
GON Turn On Gating on act ive ch anne l T im e Dom ain, Chapt er 9
GPN Enter pen number for graticule Hard Copy, Chap ter 8
GRF? Output graph type for active channe l Display, Chapte r 4
GRT Select Rectangular gate sha pe Time Domain, Chapter 9
372XXA GPIB PM 13
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
GRTCO L Enter the color num ber for the gra ticu le System State, Cha pt er 8
GRTCO L ? Graticule color num ber query System State, Chapter 8
GSN Enter gate span value time or distanc e Time Domain, Chapter 9
GSN? Output gate span value Time Domain, Chapter 9
GSP Enter gate st op va lue time or dista nce Time Dom ain, Chapter 9
GSP? Output gate stop value Time Domain, Chapter 9
GST Enter gate start value time or dis tance Time Domain, Chapter 9
GST? Output gate start value Time Domain, Chapter 9
GSX? Output gate shape Time Domain, Chapter 9
HC0 Disable Internal IF calibration Enhancement, Chapter 4
HC1 Enable Internal IF calibrat ion and trigg er an IF calibrat io n Enhancement, Chapter 4
HCT Trigger an IF calibration Enhancement, Chapter 4
HCX? Output Internal IF calibration enabled/ disa bled Enhancement, Chapter 4
HD0 Turn off tabular dat a hea der s and page f ormat ting Hard Copy, Chapter 8
HD1 Turn on tabular data hea der s and page f ormat ting Hard Copy, Chapter 8
HID Hide active segmented lim it Limits, Chapter 6
HLD Instrument Hold Measurement, Chapter 4
HLD? Hold mode quer y Measurement, Chapter 4
HPN Enter pen numb er for heade r Hard Copy , Chap ter 8
HZ Sets Frequency dat a type Data Entry Suff ixes, Chapter 4
IC1 Input Calibration Coef ficien t 1 Remote Only, Chapter 7
IC10 Input Calibration Coefficien t 10 Remote Only, Chapter 7
IC11 Input Calibration Coef ficien t 11 Remote Only, Chapter 7
IC12 Input Calibration Coefficien t 12 Remote Only, Chapter 7
IC2 Input Calibration Coef ficien t 2 Remote Only, Chapter 7
IC3 Input Calibration Coef ficien t 3 Remote Only, Chapter 7
IC4 Input Calibration Coef ficien t 4 Remote Only, Chapter 7
IC5 Input Calibration Coef ficien t 5 Remote Only, Chapter 7
IC6 Input Calibration Coef ficien t 6 Remote Only, Chapter 7
IC7 Input Calibration Coef ficien t 7 Remote Only, Chapter 7
IC8 Input Calibration Coef ficien t 8 Remote Only, Chapter 7
IC9 Input Calibration Coef ficien t 9 Remote Only, Chapter 7
14 372XXA GPIB PM
ALPHABETICAL LISTING GPIB QUICK
OF PROGRAMMING CODES REFERENCE GUIDE
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
ICA Same as IC10 Remote Only, Chapter 7
ICB Same as IC11 Remote Only, Chapter 7
ICC Same as IC12 Remote Only, Chapt er 7
ICD Input corrected data for act ive cha nnel par amet er Rem ot e Only, Chapter 7
ICF Input Front Panel Setup and Calibration data Remote Only, Chapter 7
ICF Input Front Panel Setup and Calibration data Remote Only, Chapter 7
ICL Input all applicable calibration coef ficient s for cal type Remote Only , Chapter 7
IEM Input extended statu s byte mask Remote Only, Chapter 7
IF1 Select 10 HZ IF bandwidth Enhancement, Chapter 4
IF2 Select 100 HZ IF bandwidth Enhancement, Chapter 4
IF3 Select 1 KHZ IF bandwidth Enhancement, Chapter 4
IF4 Select 10 KHZ IF bandwidth Enhancement, Chapter 4
IFA Same as IF4 Enhancement, Chapter 4
IFB Test 1st IF band pass Diagnostics, Cha pter 8
IFD Input final data for active channel parame te r Remote Only, Chapter 7
IFM Same as IF1 Enhancement, Chapt er 4
IFN Same as IF3 Enhancement, Chapt er 4
IFP Input current front panel setup Remote O nly, Chapter 7
IFP Input current front panel setup Remote O nly, Chapter 7
IFR Same as IF2 Enhancement, Chapt er 4
IFV Input frequency values Remote Only, Chapter 7
IFX? IF bandwidth quer y Enhancement , Chapter 4
IMG Select Imaginary display for active channel Display, Chapter 4
IMU Sets Imaginary data type Data Ent ry Suf f ixes, Chapt er 4
INT Initialize (format) floppy disk Disk Functions, Chapt er 8
IPM Same as *SRE IEEE-488.2, Cha pter 7
IS1 Input front panel setup 1 Remote Only, Chapt er 7
IS1 Input front panel setup 1 Remote Only, Chapt er 7
IS10 Input front panel setup 10 Remote Only, Chapt er 7
IS10 Input front panel setup 10 Remote Only, Chapt er 7
IS2 Input front panel setup 2 Remote Only, Chapt er 7
IS2 Input front panel setup 2 Remote Only, Chapt er 7
372XXA GPIB PM 15
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
IS3 Input front panel setup 3 Remote Only, Chapt er 7
IS3 Input front panel setup 3 Remote Only, Chapt er 7
IS4 Input front panel setup 4 Remote Only, Chapt er 7
IS4 Input front panel setup 4 Remote Only, Chapt er 7
IS5 Input front panel setup 5 Remote Only, Chapt er 7
IS5 Input front panel setup 5 Remote Only, Chapt er 7
IS6 Input front panel setup 6 Remote Only, Chapt er 7
IS6 Input front panel setup 6 Remote Only, Chapt er 7
IS7 Input front panel setup 7 Remote Only, Chapt er 7
IS7 Input front panel setup 7 Remote Only, Chapt er 7
IS8 Input front panel setup 8 Remote Only, Chapt er 7
IS8 Input front panel setup 8 Remote Only, Chapt er 7
IS9 Input front panel setup 9 Remote Only, Chapt er 7
IS9 Input front panel setup 9 Remote Only, Chapt er 7
ISC Select inverted compres sed Sm ith Chart for active channe l Display, Chapter 4
ISE Select inverted expanded Smith chart for active chann el Display , Chapte r 4
ISF Exclude isolation Calibration, Chapte r 5
ISM Select normal inverted Smith cha rt for active ch annel Display, Chapter 4
ISN Include isolation Calibration, Chapter 5
KEC Keep existing calibration dat a Calibration, Chapter 5
KHZ Sets Frequency dat a type and scales by 1E3 Dat a Ent ry Suf fix es, Chapt er 4
LAND Select landscape mode for output plot Hard Copy , Chap ter 8
LAX? Output lock direction Measurement , Chapter 4
LAYCOL Ent er th e color num ber for overlay data System State, Cha pt er 8
LAYCOL? Overlay da ta color nu mber query System State, Chapt er 8
LB0 Tur n limits tes ting beep on failure of f Limits, Chapt er 6
LB1 Tur n limits tes ting beep on failure on Limits, Chapt er 6
LBX? Output limits test ing bee per enable st atus Limits, Chapter 6
LCM Select LRL calibration method Calibration, Chapter 5
LDT Enter label string for date/time Hard Copy, Chapter 8
LDT? Output label string for date/time Hard Copy, Chapter 8
LFD Enter limit frequency readout delta value Limits, Chapter 6
16 372XXA GPIB PM
ALPHABETICAL LISTING GPIB QUICK
OF PROGRAMMING CODES REFERENCE GUIDE
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
LFD? Output limit frequency readout delta value Limits, Chapter 6
LFP Select limit frequency read-out for phase displays Limit s, Chapter 6
LFR Select limit frequency readout fo r active channel Limits, Chapter 6
LID Enter label string f or device ID Hard Copy, Chapter 8
LID? Output label string for device ID Hard Copy, Chapter 8
LIN Select Linear magnitude display for active channel Display, Chapter 4
LKS0 Disable lock search mode Diagnostics, Chapt er 8
LKS1 Enable lock search mod e Diagnostics, Chapter 8
LKT Load calibration kit infor ma tion from floppy disk Disk Func tion s, Chapt er 8
LL1 Enter length of line 1 for LRL calibration Calibration, Chapter 5
LL2 Enter length of line 2 for LRL calibration Calibration, Chapter 5
LL3 Enter length of line 3 for LRL calibration Calibration, Chapter 5
LLM? Output limit line display m ode, single or segmented Limits, Chapter 6
LLO Turn on lower limit and set to value Limits, Chapter 6
LLO? Output lower limit valu e for active ch anne l Limit s, Chapt er 6
LLZ Enter line impedance for LRL calibration Calibration, Chap te r 5
LM2 Select a match for the second device during a LRM type calibration Calibration, Chapter 5
LM3 Select a match for the third device during a LRM type calibration Calibrat ion, Chapter 5
LMS Enter label string for model/s erial num be r Hard Copy, Chap ter 8
LMS? Output label string for model/serial number Hard Copy , Chap ter 8
LNM Enter label string f or oper ator’s nam e Hard Copy, Chapter 8
LNM? Output label string for operator’s name Hard Copy , Chap ter 8
LO11 LO1 phase lock voltage test Diagnostics , Cha pter 8
LO12 LO1 d/a voltage t est Diagnostics , Chapt er 8
LO21 LO2 main phase lock volta ge t est Diagnostics, Chapt er 8
LO22 LO2 offset pha se lock vo ltag e test Diagnostics, Chapt er 8
LO23 LO2 dds phase lock vo ltag e test Diagnostics , Chapt er 8
LO24 LO2 main d/a voltage test Diagnostics, Chapt er 8
LO25 LO2 offset d/a volt age test Diagnostics, Chapt er 8
LOC Enter label string for operat or’s comme nt Hard Copy, Chapter 8
LOC? Output label string for operator’s comment Hard Copy, Chapter 8
LOF Limits display O f f Limits, Chapter 6
372XXA GPIB PM 17
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
LOL0 Tur n lo wer limit off Limits, Chapter 6
LOL1 Tur n lower limit on at cur ren t valu e Limits, Chapter 6
LOLX? Output lower limit on/o f f st at us Limits, Chapt er 6
LON Limits Display On Limits, Chapter 6
LON? Output Limits Display on/off status Limit s, Chapter 6
LPF? Output limit test failure status all channels Limits, Chapter 6
LPF1? Output limit test failure status on channe l 1 Limits, Chapter 6
LPF2? Output limit test failure status on channe l 2 Limits, Chapter 6
LPF3? Output limit test failure status on channe l 3 Limits, Chapter 6
LPF4? Output limit test failure status on channe l 4 Limits, Chapter 6
LPH Select linear magnitude and phase display for active channel Display, Chapter 4
LPI Select lowpass impulse response for active channel Time Domain, Chapter 9
LPS Select lowpass step response for active channe l Time Domain, Chapter 9
LPSX? Output lowpass response (impulse or step) for active ch annel Time Domain, Chapter 9
LR2 Specify 2 line LRL calibration Calibration, Chapter 5
LR3 Specify 3 line LRL calibration Calibration, Chapter 5
LS1 Set lower segment ed limit 1 as the ac tive segment Remote Only, Chapter 7
LS10 Set lower segmented limit 10 as the active segment Remote Only, Chapter 7
LS2 Set lower segment ed limit 2 as the ac tive segment Remote Only, Chapter 7
LS3 Set lower segment ed limit 3 as the ac tive segment Remote Only, Chapter 7
LS4 Set lower segment ed limit 4 as the ac tive segment Remote Only, Chapter 7
LS5 Set lower segment ed limit 5 as the ac tive segment Remote Only, Chapter 7
LS6 Set lower segment ed limit 6 as the ac tive segment Remote Only, Chapter 7
LS7 Set lower segment ed limit 7 as the ac tive segment Remote Only, Chapter 7
LS8 Set lower segment ed limit 8 as the ac tive segment Remote Only, Chapter 7
LS9 Set lower segment ed limit 9 as the ac tive segment Remote Only, Chapter 7
LSB Select least significant byte first binary transfer Remote Only , Chapt er 7
LSEG Select segmented limit line display mode Remote Only, Chapter 7
LSNG Select single limit line display mode Remote Only , Chapt er 7
LSX? Output active segm ent ed limit Remote Only, Chapter 7
LT0 Tur n limits testing off Remote Only, Chapter 7
LT1 Tur n limits testing on Remote Only, Chapter 7
18 372XXA GPIB PM
ALPHABETICAL LISTING GPIB QUICK
OF PROGRAMMING CODES REFERENCE GUIDE
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
LT1? Output limits testing ena ble stat us Remote Only, Chapter 7
LTC Select coaxial transmission line for calibration Calibration, Chapter 5
LTU Select microstrip transmission l ine for calibrat ion Calibration, Chapter 5
LTST Display the limits testing menu Limits, Chapter 6
LTW Select waveguide transmission line for calibratio n Calibration, Chapter 5
LTX? Output line type Calibration, Chapter 5
LUP Turn on upp er limit and se t to value Limits, Chapter 6
LUP? Output upper limit value for act ive cha nnel Limits, Chapter 6
LVH Set limits test ing ttl le vel high Limits, Chapter 6
LVL Set limits testing ttl level low Limits, Chapter 6
LVX? Output limits testing ttl level status Limits, Chapter 6
M Sets Distance data t ype Data Entry Suf fix es, Chapt er 4
M1C Marker 1 CW freq uency Markers, Chapter 6
M1E Marker 1 sweep/zoom end f requency, time, or dist ance Markers, Chapte r 6
M1S Marker 1 sweep/zoo m start frequency, time, or distance Markers, Chapter 6
M2C Marker 2 CW freq uency Markers, Chapter 6
M2E Marker 2 sweep/zoom end f requency, time, or dist ance Markers, Chapte r 6
M2S Marker 2 sweep/zoo m start frequency, time, or distance Markers, Chapter 6
M3C Marker 3 CW freq uency Markers, Chapter 6
M3E Marker 3 sweep/zoom end f requency, time, or dist ance Markers, Chapte r 6
M3S Marker 3 sweep/zoo m start frequency, time, or distance Markers, Chapter 6
M4C Marker 4 CW freq uency Markers, Chapter 6
M4E Marker 4 sweep/zoom end f requency, time, or dist ance Markers, Chapte r 6
M4S Marker 4 sweep/zoo m start frequency, time, or distance Markers, Chapter 6
M5C Marker 5 CW freq uency Markers, Chapter 6
M5E Marker 5 sweep/zoom end f requency, time, or dist ance Markers, Chapte r 6
M5S Marker 5 sweep/zoo m start frequency, time, or distance Markers, Chapter 6
M6C Marker 6 CW freq uency Markers, Chapter 6
M6E Marker 6 sweep/zoom end f requency, time, or dist ance Markers, Chapte r 6
M6S Marker 6 sweep/zoo m start frequency, time, or distance Markers, Chapter 6
MAG Select log magnitude display for active channel Display , Chapte r 4
MAT Select matched reflective de vices du ring ca l Calibration, Chapter 5
372XXA GPIB PM 19
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
MEM Display Trace Mem ory on a ctive cha nnel Display, Chapte r 4
MHZ Sets Frequency data type and scales by 1E 6 Dat a Entry Suffixes, Chapter 4
MIN Select Subtraction as Trace Mat h for active ch anne l D isplay, Chapter 4
MIX Select mixed reflective device s during cal Calibration, Chapter 5
MK1 Turn on Marker 1 and set to frequency, time or distance Markers, Chapter 6
MK1? Output Marker 1 frequency, time or distance Marke rs, Chapte r 6
MK2 Turn on Marker 2 and set to frequency, time or distance Markers, Chapter 6
MK2? Output Marker 2 frequency, time or distance Marke rs, Chapte r 6
MK3 Turn on Marker 3 and set to frequency, time or distance Markers, Chapter 6
MK3? Output Marker 3 frequency, time or distance Marke rs, Chapte r 6
MK4 Turn on Marker 4 and set to frequency, time or distance Markers, Chapter 6
MK4? Output Marker 4 frequency, time or distance Marke rs, Chapte r 6
MK5 Turn on Marker 5 and set to frequency, time or distance Markers, Chapter 6
MK5? Output Marker 5 frequency, time or distance Marke rs, Chapte r 6
MK6 Turn on Marker 6 and set to frequency, time or distance Markers, Chapter 6
MK6? Output Marker 6 frequency, time or distance Marke rs, Chapte r 6
MKRC Select interpolated marker functionality Markers, Chapter 6
MKRCOL Enter the color number for the markers, time or distance System State, Chapt er 8
MKRCOL? Markers color num ber quer y System State, Cha pt er 8
MKRD Select discrete marker functionality Markers, Chapter 6
MKRX? Outpu t inter polat ed/disc rete marker functio nality Markers, Chapter 6
MKSL Marker search left Markers, Chapter 6
MKSR Marker sear ch right Markers, Chapter 6
MKT0 Turn marker tracking of f Markers, Chapter 6
MKT1 Turn marker tracking on Markers, Chapter 6
MKTX? Output marker tracking on/off status Markers, Chapter 6
MM Sets Distance dat a type a n d scales by 1E-3 Data Entry Suf fix es, Chapter 4
MMN Set active Marker to minimum trace value Markers, Chapter 6
MMT Same as MM Data Entry Suf fix es, Chapt er 4
MMX Set active marker to m axim um trace value Markers, Chapter 6
MNUCOL Enter the color number for the me nu hea der s System State, Chapt er 8
MNUCOL? Menu header color number quer y System State, Cha pt er 8
20 372XXA GPIB PM
ALPHABETICAL LISTING GPIB QUICK
OF PROGRAMMING CODES REFERENCE GUIDE
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
MO1 T urn Off marker 1 Markers, Chapter 6
MO2 T urn Off marker 2 Markers, Chapter 6
MO3 T urn Off marker 3 Markers, Chapter 6
MO4 T urn Off marker 4 Markers, Chapter 6
MO5 T urn Off marker 5 Markers, Chapter 6
MO6 T urn Off marker 6 Markers, Chapter 6
MOF Turn Marker display Off Markers, Chapter 6
MON Turn Marker display On Markers, Chapter 6
MON? Outpu t marker display on/ of f statu s Markers, Chapter 6
MPH Select log magnitude and phase disp la y for active channe l Display, Chapter 4
MPN Enter pen numb er for markers and limits Hard Copy, Chapter 8
MR1 Select Readout marker 1 Markers, Chapter 6
MR1? Output marker 1 on/off status Markers, Chapter 6
MR2 Select Readout marker 2 Markers, Chapter 6
MR2? Output marker 2 on/off status Markers, Chapter 6
MR3 Select Readout marker 3 Markers, Chapter 6
MR3? Output marker 3 on/off status Markers, Chapter 6
MR4 Select Readout marker 4 Markers, Chapter 6
MR4? Output marker 4 on/off status Markers, Chapter 6
MR5 Select Readout marker 5 Markers, Chapter 6
MR5? Output marker 5 on/off status Markers, Chapter 6
MR6 Select Readout marker 6 Markers, Chapter 6
MR6? Output marker 6 on/off status Markers, Chapter 6
MRR Restore original Marker range Time Domain, Chapter 9
MRX? Output ac tive marker number Markers, Chapter 6
MS Sets Time data type and scales by 1E-3 Data Entry Suf f ixes, Chapt er 4
MS0 Turn Multiple Source mode Off Multiple Source Control, Chapter 9
MS1 Turn Multiple Source mode On Multiple Source Control, Chapter 9
MSB Select most significant byte first binary transfer Rem ot e O nly, Chapter 7
MSD Select multiple Source define m ode Multiple Source Control, Chapter 9
MSFH Enter high loss value for shape factor calculat ion Markers, Chapte r 6
MSFH? Output high loss value for shape factor calculation Markers, Chapter 6
372XXA GPIB PM 21
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
MSFL Enter low loss value for shape factor calculation Markers, Chapter 6
MSFL? Output low loss value for shape factor calculation Markers, Chapter 6
MSR0 Select 0 as ref for marker search and bandwidth calcula tion Markers, Chapter 6
MSRD Select delta ref marker as ref for marker search and bandwidth
calculat
MSRM Select max as ref for marker search and bandwidth calculation Markers, Chapter 6
MSRX? Outp u t ref selection f or marker sear ch and bandwidt h calculat io n Markers, Chapter 6
MSX? Output multiple source m ode on /off/define Multiple Source Control, Chapt er 9
MTH? Output trace math math type Display , Chap ter 4
MTR Same as M Data Entry Suf fix es, Chapt er 4
MUL Select Multiplication as trace Math for active chan nel D isplay, Chapter 4
MV Sets Voltag e dat a type an d scales by 1E-3 Data Entry Suffixes, Chapt er 4
NCS Go to next calibration step Calibration, Chapter 5
NMKR Select normal markers on active channel marker mode Markers, Chapter 6
NOC Select Normal Calibration dat a points Calibration, Chapter 5
NP101 Set data points to 10 1 Measur ement, Chapter 4
NP1601 Set data po in ts to 1601 Measurement, Chapter 4
NP201 Set data points to 20 1 Measur ement, Chapter 4
NP401 Set data points to 40 1 Measur ement, Chapter 4
NP51 Set data points to 51 Measurem ent, Chapter 4
Markers, Chapter 6
NP801 Set data points to 80 1 Measur ement, Chapter 4
NRD Display non-ratioed parameters on 4 channels Diagnostics, Chapter 8
NS Sets Time data type and scales by 1E-9 Data Entry Suffixes, Chapter 4
NSC Same as NS Data Entry Suf fix es, Chapter 4
OAM1 Output channel 1 ac tive marker value Remote Only, Chapter 7
OAM2 Output channel 2 ac tive marker value Remote Only, Chapter 7
OAM3 Output channel 3 ac tive marker value Remote Only, Chapter 7
OAM4 Output channel 4 ac tive marker value Remote Only, Chapter 7
OC1 Output Calibration Coefficien t 1 Remote Only , Chapter 7
OC10 Output Calibration Coefficient 10 Remote Only, Chapter 7
OC11 Output Calibration Coefficient 11 Rem ot e Only, Chapter 7
OC12 Output Calibration Coefficient 12 Remote Only, Chapter 7
22 372XXA GPIB PM
ALPHABETICAL LISTING GPIB QUICK
OF PROGRAMMING CODES REFERENCE GUIDE
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
OC2 Output Calibration Coefficien t 2 Remote Only , Chapter 7
OC3 Output Calibration Coefficien t 3 Remote Only , Chapter 7
OC4 Output Calibration Coefficien t 4 Remote Only , Chapter 7
OC5 Output Calibration Coefficien t 5 Remote Only , Chapter 7
OC6 Output Calibration Coefficien t 6 Remote Only , Chapter 7
OC7 Output Calibration Coefficien t 7 Remote Only , Chapter 7
OC8 Output Calibration Coefficien t 8 Remote Only , Chapter 7
OC9 Output Calibration Coefficien t 9 Remote Only , Chapter 7
OCA Same as OC10 Remote Only, Chapter 7
OCB Same as OC11 Remote Only, Chapter 7
OCC Same as OC12 Rem ote Only, Chapter 7
OCD Output correct ed da ta for act ive cha nnel par am eter Remote Only, Chapter 7
OCF Output Front Panel Setup and Calibration data Remot e Only, Chapter 7
OCF Output Front Panel Setup and Calibration data Remot e Only, Chapter 7
OCL Output all applicable calibration coefficient s for cal type Remot e Only, Chapter 7
OCM Select Offset shor t calibration m et hod Calibration, Chapte r 5
ODR Output director y listing of t he flo ppy drive Hard Copy, Chapter 8
ODR Output director y listing of t he flo ppy drive Hard Copy, Chapter 8
ODRH Output directory listing of t he hard dr ive Hard Copy , Chap te r 8
ODRH Output directory listing of t he hard dr ive Hard Copy , Chap te r 8
ODV Output distance values for time domain Remote Only , Chapt er 7
OEB Output extended statu s byte Remote Only , Chapt er 7
OEL Output error log Remote Only, Chapter 7
OEM Output extended status byte mask Remote Only, Chapter 7
OFD Output final data f or active channel para me te r Remote Only , Chapt er 7
OFF Set offset level on active cha nnel display Display, Chapter 4
OFF? Output offset level on active ch anne l display Display , Chap ter 4
OFP Output current Front Panel Set up Remote Only, Chapter 7
OFP Output current Front Panel Set up Remote Only, Chapter 7
OFV Output Frequency values Remote Only , Chapt er 7
OGE Output exte nded descr ipt io n of current gpib erro r Remote Only, Chapter 7
OGL Output ex tended descr ipt io n of prev ious gpib er ro r Remote Onl y, Chapter 7
372XXA GPIB PM 23
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
OHM Sets Impedance d a ta typ e Data Entry Suffixes, Chapt er 4
OID Output instr um ent ident ifica tion string System State, Chapt er 8
OLB Output limits status byte Remote Only, Chapter 7
OLM Output limits status byte mask Remote Only, Chapter 7
OM1 Output Marker 1 value Remote Only , Chapt er 7
OM2 Output Marker 2 value Remote Only , Chapt er 7
OM3 Output Marker 3 value Remote Only , Chapt er 7
OM4 Output Marker 4 value Remote Only , Chapt er 7
OM5 Output Marker 5 value Remote Only , Chapt er 7
OM6 Output Marker 6 value Remote Only , Chapt er 7
ONCT Output number of cal terms for current cal Limits, Chapter 6
ONE Output number of lines in the error log Calibration, Chap te r 5
ONP Output Number of points current ly being measu red Remote Only, Chapter 7
OPB Same as *STB? IEEE-488 .2 , Chapter 7
ORD Output Raw data for active cha nnel param et er Remote Only, Chapter 7
OS1 Output front panel Setup nu mb er 1 Remote Only, Chapt er 7
OS1 Output front panel Setup nu mb er 1 Remote Only, Chapt er 7
OS10 Output front panel Setup nu mb er 10 Remote Only, Chapt er 7
OS10 Output front panel Setup nu mb er 10 Remote Only, Chapt er 7
OS2 Output front panel Setup nu mb er 2 Remote Only, Chapt er 7
OS2 Output front panel Setup nu mb er 2 Remote Only, Chapt er 7
OS3 Output front panel Setup nu mb er 3 Remote Only, Chapt er 7
OS3 Output front panel Setup nu mb er 3 Remote Only, Chapt er 7
OS4 Output front panel Setup nu mb er 4 Remote Only, Chapt er 7
OS4 Output front panel Setup nu mb er 4 Remote Only, Chapt er 7
OS5 Output front panel Setup nu mb er 5 Remote Only, Chapt er 7
OS5 Output front panel Setup nu mb er 5 Remote Only, Chapt er 7
OS6 Output front panel Setup nu mb er 6 Remote Only, Chapt er 7
OS6 Output front panel Setup nu mb er 6 Remote Only, Chapt er 7
OS7 Output front panel Setup nu mb er 7 Remote Only, Chapt er 7
OS7 Output front panel Setup nu mb er 7 Remote Only, Chapt er 7
OS8 Output front panel Setup nu mb er 8 Remote Only, Chapt er 7
24 372XXA GPIB PM
ALPHABETICAL LISTING GPIB QUICK
OF PROGRAMMING CODES REFERENCE GUIDE
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
OS8 Output front panel Setup nu mb er 8 Remote Only, Chapt er 7
OS9 Output front panel Setup nu mb er 9 Remote Only, Chapt er 7
OS9 Output front panel Setup nu mb er 9 Remote Only, Chapt er 7
OSL Output service log Remote Only, Chapter 7
OTV Output time values for time domain Remote Only, Chapter 7
P1C Select Port 1 for connector specificat ion Calibration, Chapter 5
P1C? Output port 1 connector type Calibration, Chap te r 5
P1P? Output appro xima te power level at port 1 Calibration, Chapter 5
P2C Select Port 2 for connector specificat ion Calibration, Chapter 5
P2C? Output port 2 connector type Calibration, Chap te r 5
PBL Select 1/4 size plot, bottom left corner Hard Copy, Chap te r 8
PBR Select 1/4 size plot, bottom right corner Hard Copy, Chapter 8
PCP Select measurement phase polar chart mode Display, Chap ter 4
PCS Select sweep position polar chart mode Display, Chapter 4
PCX? Output Polar chart mode Display, Chapter 4
PDR Print direct ory listing of the f loppy dr iv e Disk Functions, Chapt er 8
PDRH Print directory listing of the hard drive Disk Functions, Chapt er 8
PEL Print the error log Diagnos tics , Cha pt er 8
PFL Select Full-size plot Hard Copy , Chapte r 8
PFS Print Full screen image Hard Copy, Chapte r 8
PGR Print graph area screen image Hard Copy, Chapter 8
PGT Plot graticule Hard Copy, Chapter 8
PHA Select phase display for active channel Display, Chapter 4
PHO Set Phase Offset for display chan nel Display, Chapter 4
PHO? Output phase Offset for display channe l D isplay, Chapter 4
PLD Plot data area only Hard Copy, Chapter 8
PLG Select log polar display for active channel Display, Chapter 4
PLH Plot header Hard Copy, Chapter 8
PLM Plot Markers and Limits Hard Copy, Chapter 8
PLO? Output plot m ode, portrait or landscape Hard Copy, Chapter 8
PLR Select linear polar display for active channe l Display , Chapte r 4
PLS Plot entire screen Hard Copy, Chapter 8
372XXA GPIB PM 25
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
PLT Plot data traces only Hard Copy, Chap ter 8
PMK Print tabular data for Markers Hard Copy, Chapte r 8
PMN Plot Menu Hard Copy, Chapter 8
PMT Print Tabular data for Traces and Markers Hard Copy, Chapter 8
PORT Select portrait mode f or output plot Hard Copy, Chapter 8
PRT? Printer peripher al te st and que ry Peripheral Tests, Chapter 8
PS Sets Time dat a type and scales by 1E-12 Data Entry Suff ixes, Chapter 4
PSC Same as PS Data Entry Suf fix es, Chapt er 4
PSL Print the service log Diagnostics, Chapter 8
PSP Number of power sweeps for flat power co rrect ion Calibration, Chapter 5
PSP? Output number of power sweeps for flat power correction Calibration, Chap ter 5
PST Stop Print/Plot Hard Copy, Chapter 8
PT0 Set Tabular Printout points skipped to 0 Hard Copy, Chapte r 8
PT1 Set Tabular Printout points skipped to 1 Hard Copy, Chapte r 8
PT2 Set Tabular Printout points skipped to 2 Hard Copy, Chapte r 8
PT3 Set Tabular Printout points skipped to 3 Hard Copy, Chapte r 8
PT4 Set Tabular Printout points skipped to 4 Hard Copy, Chapte r 8
PT5 Set Tabular Printout points skipped to 5 Hard Copy, Chapte r 8
PT6 Set Tabular Printout points skipped to 6 Hard Copy, Chapte r 8
PT7 Set Tabular Printout points skipped to 7 Hard Copy, Chapte r 8
PT8 Set Tabular Printout points skipped to 8 Hard Copy, Chapte r 8
PT9 Set Tabular Printout points skipped to 9 Hard Copy, Chapte r 8
PTB Print tabular data for T ra ces Hard Copy, Chapter 8
PTL Select 1/4 size plot, top left corner Hard Copy, Chapter 8
PTR Select 1/4 size plot, top right corner Hard Copy, Chapte r 8
PTS Number of points to be skipp ed dur ing fla t power co rrection Calibration, Chapter 5
PTS? Output number of points to be skip ped du ring f lat power correct ion Calibration, Chapte r 5
PW2 Set external source power level Measurement, Chapter 4
PW2? Output external source power level Measurement, Chapter 4
PWR Set internal s ource power level Measurem ent, Chapter 4
PWR? Outpu t inter nal sour ce po wer leve l Measurement , Chapter 4
RAD Sets Phase data type and sca le s by 180/p i Data Entry Suffixes, Chapt er 4
26 372XXA GPIB PM
ALPHABETICAL LISTING GPIB QUICK
OF PROGRAMMING CODES REFERENCE GUIDE
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
RC1 Recall Front Panel Setup num ber 1 from memory Save/Recall, Chapte r 8
RC10 Recall Front Panel Set up number 10 from memory Save/Recall, Chapter 8
RC2 Recall Front Panel Setup num ber 2 from memory Save/Recall, Chapte r 8
RC3 Recall Front Panel Setup num ber 3 from memory Save/Recall, Chapte r 8
RC4 Recall Front Panel Setup num ber 4 from memory Save/Recall, Chapte r 8
RC5 Recall Front Panel Setup num ber 5 from memory Save/Recall, Chapte r 8
RC6 Recall Front Panel Setup num ber 6 from memory Save/Recall, Chapte r 8
RC7 Recall Front Panel Setup num ber 7 from memory Save/Recall, Chapte r 8
RC8 Recall Front Panel Setup num ber 8 from memory Save/Recall, Chapte r 8
RC9 Recall Front Panel Setup num ber 9 from memory Save/Recall, Chapte r 8
RCK Same as RCLNRM D isk Function s, Chapt er 8
RCKH Same as RCLNRMH Disk Functions, Chapter 8
RCLALC Rec all ALC Cal file f rom flo ppy disk Disk Functions, Chapter 8
RCLALCH Recall ALC Cal file from hard disk Disk Function s, Chapt er 8
RCLALL Recal l Combined Hardware Cal fi le from floppy disk Disk Function s, Chapter 8
RCLALLH Recall Combined Hardware Cal file from hard disk Disk Functions, Chapter 8
RCLCAL Rec al l Calibratio n/Fro nt Panel Set up f rom flo ppy disk Disk Functions, Chapt er 8
RCLCALH Recall Calibration/Front Panel Setup from hard disk Disk Functions, Chapter 8
RCLDAT Recall Tabular data file from floppy disk to printer Disk Functions, Chapter 8
RCLDATH Recall Tabular data file from har d disk to p rint er Disk Functions, Chapt er 8
RCLELG Recall Error Log file from floppy disk to printer Disk Functions, Chapter 8
RCLELGH Recall Error Log file from hard disk to printe r Disk Functions, Chapter 8
RCLFRE Recall Frequency Cal file from floppy disk Disk Functions, Chapter 8
RCLFREH Recall Frequency Cal file from hard disk Disk Functions, Chapter 8
RCLLOG Recall Service Log file from flo ppy disk to printer Disk Functions, Chapt er 8
RCLLOG H Recall Service Log file from hard disk t o prin ter Disk Functions, Chapter 8
RCLNRM Recal l Tra ce Mem ory File from floppy disk D isk Func tion s, Chapt er 8
RCLNRMH Rec al l Tra ce Mem ory File from hard disk Disk Function s, Chapt er 8
RDA Select Autom at ic Reference delay calculation Display, Chapter 4
RDD Set reference delay in distance for active channe l Display, Chapter 4
RDD? Output reference delay in distance for active chan ne l Display, Chapte r 4
RDT Set reference delay in time for active channel Display, Chap ter 4
372XXA GPIB PM 27
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
RDT? Output reference delay in time for active channe l Display, Chapter 4
REF Set reference line for display on active channel Display, Chapte r 4
REF? Output refere nce line for displa y on active ch anne l Display, Chapter 4
REL Select real display for active channel Display, Chapter 4
REU Sets Real data type Data Entry Suff ixes, Chapter 4
RGZ Select reflective device grea ter than Z0 Calibration, Chapter 5
RH0 Set RF Off while in Hold Measurem ent, Chapter 4
RH1 Set RF On while in Hold Measurement, Chapter 4
RHX? Output RF on/off during Hold status Measurem ent, Chapter 4
RIM Select Real and Imaginary display for active channel Display, Chapter 4
RLD Same as RCLCAL Disk Function s, Chapt er 8
RLDH Same as RCLCALH Disk Functions, Chapter 8
RLZ Select Reflective device less than Z0 Calibration, Chapter 5
RM1 Select reference plan e at line 1 midpoint Calibration, Chapter 5
ROL Enter reflective device of fs et length Calibration, Chapter 5
RPC Repeat previous calibratio n Calibration, Chapter 5
RPO Set rear panel dc voltage value Rear Ranel Output , Chapt er 9
RPO? Output rear panel dc voltage to gpib Rear Ranel Output, Chapt er 9
RRP Select reference plan e at reflect ion plane Calibration, Chapter 5
RST Same as *RST System State, Chapter 8
RST0 Reset instrument plus fro nt panel mem ories and re ser ved
param eters
RST1 Reset instrum ent plus fro nt panel m em ories System State , Cha pter 8
RTB Same as RCLDAT Disk Functions, Chapt er 8
RTBH Same as RCLDA T H D isk Function s, Chapt er 8
RTL Return to Local System State, Chapter 8
RV0 Tur n Rear panel out pu t voltag e Of f Rear Ra nel Out put , Ch apt er 9
RV1 Tur n Rear panel out pu t voltag e On Rear Ranel Output, Chapt er 9
System State , Cha pt er 8
RV1? Output Rear panel output voltage on /o f f stat us Rear Ranel Output, Chapt er 9
RVD Set Rear pane l output mode to dc value Rear Ranel Out put, Chapter 9
RVH Set Rear pane l ou tp ut mode to horizontal Rear Ranel Output, Chapter 9
RVL Set Rear pane l output mode to lock direction Rear Ranel Output, Chapter 9
28 372XXA GPIB PM
ALPHABETICAL LISTING GPIB QUICK
OF PROGRAMMING CODES REFERENCE GUIDE
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
RVV Set Rear panel output mode to vertical Rear Ranel Output, Chapt er 9
RVX? Output rear panel output mode Rear Ranel Output , Chapt er 9
S Set s Time data type Data Entry Suffixes, Chapt er 4
S11 Measure S1 1 on ac tive channe l Display, Chapte r 4
S12 Measure S12 on active ch anne l Display, Chapte r 4
S21 Measure S21 on active ch anne l Display, Chapte r 4
S22 Measure S22 on active ch anne l Display, Chapte r 4
SA1 Enter Port 1 source att enuator setting Measurement, Chapt er 4
SA1? Output Port 1 source at tenua to r sett ing Measurement , Chapter 4
SAVALC Sav e ALC Ca l to f loppy disk Disk Functions, Chapt er 8
SAVALCH Save ALC Cal to hard d isk Disk Functions, Chapter 8
SAVALL Save Combined Hardware Cal to floppy disk Disk Functions, Chapt er 8
SAVALLH Save Combined Hardware Cal to hard disk Disk Functions, Chapter 8
SAVCAL Save Calibration/Front Panel Setup to floppy disk Disk Functions, Chapt er 8
SAVCALH Save Calibration/Fr ont Panel Setup to hard disk Disk Functions, Chapter 8
SAVDAT Save Tabular Data to floppy disk Disk Function s, Chapt er 8
SAVDATH Save Tabular Data to hard disk Disk Functions, Chapt er 8
SAVELG Save Error Log to floppy disk Disk Functions, Chapter 8
SAVELGH Save Error Log to hard disk Disk Functions, Chapter 8
SAVFRE Sav e Fre quency Cal to floppy disk Disk Functions, Chapter 8
SAVFREH Save Frequency Cal to hard disk Disk Function s, Chapter 8
SAVLOG Sav e Serv ice Log to f loppy disk Disk Functions, Chapter 8
SAVLOGH Save Service Log to hard disk Disk Functions, Ch apt er 8
SAVNRM Save Trace Memory to floppy disk Disk Functions, Chapter 8
SAVNRMH Save Trace Memory to hard dis k Disk Functions, Chapter 8
SBD Enter substrate dielectric for microstr ip ca l ibrat i on Calibration, Chapter 5
SBT Enter substrat e thickne ss for micro st rip calibr atio n Calibration, Chapter 5
SCL Set Scale Resolution on act ive ch anne l Display, Chap ter 4
SCL? Output Scale Resolution on active channe l Display, Chapter 4
SCM Select standard calibration metho d Calibration, Chapter 5
SDG Start diagnostics mode Diagnostics, Cha pter 8
372XXA GPIB PM 29
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
SDK Same as SAVNRM Disk Functions, Chapter 8
SDKH Same as SAVNRMH Disk Functions, Chapter 8
SDR Select standard receiver mode Diagnostics, Chapter 8
SERNUM Enter instrument serial number System State, Chapt er 8
SETUP Display setup menu Measurement, Chapt er 4
SFC Start flat test port calibration Calibration, Chapter 5
SH1 Set offset short 1 offset length Calibration, Chap te r 5
SH2 Set offset short 2 offset length Calibration, Chap te r 5
SL1 Select Source lock mode with GPIB source contro l On Diagnostics, Chapt er 8
SLC Clear all segmented limits definitions Limits, Chapter 6
SLD Select sliding load for calibration Calibration, Chapter 5
SLH Set segment ed l imits hor izont al of fs e t Limits, Chapter 6
SLH? Output segmented limit s horizont al offset Limits, Chapter 6
SLL0 Tur n lower se gm ent ed limit s display of f Limits, Chapter 6
SLL1 Tur n lower se gm ent ed limit s display on Limits, Chapter 6
SLLX? Outpu t lower segmen te d limits display on/ off status Limits, Chapter 6
SLU0 Turn upper segment ed l imits display off Limits, Chapter 6
SLU1 Turn upper segmented l imits display on Limits, Chapter 6
SLUX? Output upper segment ed limits displa y on/ of f stat us Limits, Chapter 6
SLV Set segmented limit s vertical offset Limits, Chapter 6
SLV? Output segmented limit s ver tic al off set Limits, Chapter 6
SMC Select compressed Sm ith char t for activ e chann el Display, Chap te r 4
SME Select expanded Smith chart for active channel Display, Chapte r 4
SMI Select normal smith chart for active chann el Display, Chapter 4
SMKR Select marker search marker mode Markers, Chapter 6
SOF Turn Off smoothing Enhancement, Chapter 4
SOF? Output smoothing on/off status Enhancement, Chapter 4
SON Turn On smoothing and set to value Enhancement, Chapter 4
SON? Output smoothing value Enhancement, Chapter 4
SPAN Enter frequ ency span Measur em ent, Chapter 4
SPAN? Output fre quen cy span Measurement, Chapt er 4
30 372XXA GPIB PM
ALPHABETICAL LISTING GPIB QUICK
OF PROGRAMMING CODES REFERENCE GUIDE
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
SPD Enter pen speed percentage Hard Copy , Chapte r 8
SPH Set active segmented limit hor izont al st op pos ition Limits, Chapter 6
SPH? Outpu t active segment ed limit horizont al st op po sition Limits, Chapter 6
SPV Set active segmented limit ver tical stop positio n Limits, Chapter 6
SPV? Output active segmented limit vert ical s to p posit ion Limits, Chapter 6
SRC1 Source linearity voltage t est Diagnostics, Cha pt er 8
SRC2 Source power voltage test Diagnostics, Chapter 8
SRCH Enter marker search value Markers, Chapter 6
SRCH? Output marker search value Markers, Chapter 6
SRT Start Frequency Measurement, Chapter 4
SRT? Output Star t Frequ ency Measurement, Chapter 4
ST1 Select set on mode with GPIB source control on Diagnostics, Chapt er 8
STD Store trace to memory on active channe l Display, Chapter 4
STH Set active segmented limit hor iz ontal start position Limits, Chapter 6
STH? Output active segm ent ed limit hor izont al star t position Limits, Chapter 6
STOH Same as SAVCALH Disk Functions, Chapter 8
STP Stop Frequ ency Me asurement, Chapt er 4
STP? Output Stop Frequency Measurement , Chapt er 4
STV Set active segmented limit vertical start posit ion Limits, Chapter 6
STV? Output active segm ent ed limit vertical s tart position Limits, Chapter 6
SV1 Save front panel setup number 1 to memory Save/Recall, Chapter 8
SV10 Save front panel setup num be r 10 to mem ory Save/Recall, Chapter 8
SV2 Save front panel setup number 2 to memory Save/Recall, Chapter 8
SV3 Save front panel setup number 3 to memory Save/Recall, Chapter 8
SV4 Save front panel setup number 4 to memory Save/Recall, Chapter 8
SV5 Save front panel setup number 5 to memory Save/Recall, Chapter 8
SV6 Save front panel setup number 6 to memory Save/Recall, Chapter 8
SV7 Save front panel setup number 7 to memory Save/Recall, Chapter 8
SV8 Save front panel setup number 8 to memory Save/Recall, Chapter 8
SV9 Save front panel setup number 9 to memory Save/Recall, Chapter 8
SVB Save current band definit io ns Multiple Source Contr ol, Chapt er 9
SWP Return to normal sweep mode Measurem ent , Chapt er 4
372XXA GPIB PM 31
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
SWP? Output Sweep Mode Measurement, Chapter 4
SWR Select SWR display for active channel Display, Chap ter 4
SXX? Output S-parameter displayed on activ e channe l Display, Chapter 4
T13 Select overlaid channel 1 and 3 display Channels, Chapt er 4
T24 Select overlaid channel 2 and 4 display Channels, Chapt er 4
TA2 Enter Port 2 t est attenuator setting Measurement, Chapter 4
TA2? Output Port 2 test attenu at or setti ng Measur em ent , Chapt er 4
TBP Select time bandpass mode for active cha nnel Tim e Domain, Chapt er 9
TC1 T ak e calibration dat a for port 1 Calibration, Chapter 5
TC2 T ak e calibration dat a for port 2 Calibration, Chapter 5
TCD T ak e calibra tion data on one or both po rts as necess ary Calibration, Chapter 5
TDC Select time domain harmonic frequency cal data point s Calibration, Chapter 5
TDD Same as SA VD AT Disk Functions, Chapt er 8
TDDH Same as SAVDAT H Disk Functions, Chapt er 8
TDDIST Set time domain parame te r to distance for active cha nnel Time Domain, Chapter 9
TDDIST? Output active channel tim e domain par am et er (time or distance ) Time Domain, Chapter 9
TDL Through DC coef fic ient for loss Calibration, Chapter 5
TDPI0 Turn phasor impulse respo nse off for active channel Time Dom ain, Chapt er 9
TDPI1 Turn phasor impulse respo nse on for active cha nnel T im e Domain, Chapt er 9
TDPIX? Output phasor impuls e on/off status for active cha nnel Time Domain, Chapt er 9
TDTIME Set time domain parame te r to time for active chann e l Time Domain, Chapt er 9
TDX? Output domain mode fo r active channe l Time Domain, Chapt er 9
TEX Select externa l measurement triggering Measurement , Chapter 4
TFE Through frequency expo nent for loss Calibration, Chapter 5
TFL Through f req uenc y coefficient for loss Calibration, Chapter 5
TIN Select internal measurem ent trigger Measurement, Chapter 4
TK1 Select tracking mode with GPIB sour ce control O n Diagnos tics , Chapter 8
TLP Select time lowpass mode for active channel Time Domain, Chapter 9
TLZ Enter through line impedance for calibration Calibration, Chap te r 5
TOL Enter through offset length for calibration Calibration, Chapter 5
TPI Select time phasor impulse mode f or active chan nel Time Domain, Chapter 9
32 372XXA GPIB PM
ALPHABETICAL LISTING GPIB QUICK
OF PROGRAMMING CODES REFERENCE GUIDE
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
TPN Enter pen number for trace ov erlay data Hard Copy, Chapte r 8
TRCCOL Enter the color number for memory data System State , Chapter 8
TRCCOL? Memory data color number quer y System Sta te, Chapt er 8
TRS Trigger/Res ta rt Sweep Measurement, Chapter 4
TST Same as *TST? IEEE-488.2, Chapter 7
TXX? Output trigger source Measurement, Chapt er 4
U10 Select 10 mil UTF calibration kit Calibration, Chapter 5
U15 Select 15 mil UTF calibration kit Calibration, Chapter 5
U25 Select 25 mil UTF calibration kit Calibration, Chapter 5
UPL0 Turn upper limit off Limits, Chapter 6
UPL1 Turn upper limit on at current value Limits, Chapter 6
UPLX? Output upper limit on/off status Limits, Chapter 6
US Sets Time data type and scales by 1E-6 Data Entry Suffixes, Chapter 4
US1 Set upper segment ed limit 1 as the act ive se gm ent Limits, Chapter 6
US10 Set upper segmented limit 10 as the ac tive segm ent Limits, Chapter 6
US2 Set upper segment ed limit 2 as the act ive se gm ent Limits, Chapter 6
US3 Set upper segment ed limit 3 as the act ive se gm ent Limits, Chapter 6
US4 Set upper segment ed limit 4 as the act ive se gm ent Limits, Chapter 6
US5 Set upper segment ed limit 5 as the act ive se gm ent Limits, Chapter 6
US6 Set upper segment ed limit 6 as the act ive se gm ent Limits, Chapter 6
US7 Set upper segment ed limit 7 as the act ive se gm ent Limits, Chapter 6
US8 Set upper segment ed limit 8 as the act ive se gm ent Limits, Chapter 6
US9 Set upper segment ed limit 9 as the act ive se gm ent Limits, Chapter 6
USC Same as US Data Entry Suf fix es, Chapter 4
USE Enter effective die lect ric for micro st rip calibr at ion Calibration, Chapter 5
USW Enter micr ost rip width for micr ost rip ca librat io n Calibration, Chapter 5
USZ Enter microst r ip impedance for microstrip calibration Calibration, Chapter 5
V Set s Voltage data type Data Entry Suffixes, Chapter 4
VLT Same as V Data Entry Suf fix es, Chapt er 4
VSP Stop voltage value Rear Ranel Output, Ch apt er 9
VSP? Output stop voltage value Rear Ranel Output , Chapt er 9
VST Start voltage value Rear Ranel O ut put , Chapt er 9
372XXA GPIB PM 33
GPIB QUICK ALPHABETICAL LISTING
REFERENCE GUIDE OF PROGRAMMING CODES
Table 1. Alphabetical Listing of Programming Codes (Mnemonics)
Command Description Functional Group
VST? Output start voltage value Rear Ranel Output, Chapt er 9
WCO Set waveguide cutoff frequency for user defined kit Calibration, Chapter 5
WFS Wa it f ul l sweep until all display data is va l id Measurement, Chapter 4
WKD Select user defined waveguide calibr atio n kit Calibration, Chapter 5
WKI Select installed waveguide calibration kit Calibration, Chapter 5
WLS Select low sidelobe window shape Time Domain, Chapter 9
WMS Select minimum sidelobe window shape Time Dom ain, Chapter 9
WNM Select nominal window shape Time Domain, Chapt er 9
WRT Select rectangular window shape Tim e Dom ain, Chapt er 9
WSH1 Set wave guide short offset 1 for user defined kit Calibration, Chapter 5
WSH2 Set wave guide short offset 2 for user defined kit Calibration, Chapter 5
WSX? Output window shape Tim e Domain, Chapt er 9
XM3 Sets Unitless data type and scales by 1E3 Data Entry Suffixes, Chapter 4
XMKR? Output marker mode Markers, Chapter 6
XX1 Sets Unitless data type Data Entry Suffixes, Chapt er 4
XX3 Sets Unitless data type and scales by 1E-3 Data Entry Suf f ixes, Chapt er 4
ZCT Enter zoom range ce nt er valu e time or distance Time Domain, Chapt er 9
ZCT? Output zoom range center value Time Domain, Chapter 9
ZSN Enter zoom range sp an value time or distan ce Time Domain, Chapter 9
ZSN? Output zoom rang e span value Time Domain, Chapter 9
ZSP Enter zoom range stop value t ime or distance Time Domain, Chapter 9
ZSP? Output zoom range stop value Time Domain, Chapter 9
ZST Enter zoom range star t value t ime or distance Time Domain, Chapter 9
ZST? Output zoom range start value Time Domain, Chapt er 9
34 372XXA GPIB PM
GPIB QUICK PROGRAMMING CODES,
REFERENCE GUIDE FUNCTIONAL GROUPING
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
Distance Suf fix Mnem oni cs , Cha pte r 4
CM Sets Distanc e data t ype an d scales by
1E-2
MM Sets Distance data type an d scales by
1E-3
M Sets Distanc e dat a type
Frequency
GHZ Sets Frequency dat a type and scales
by 1E9
HZ Sets Frequ ency data type
KHZ Sets Frequency dat a type and scales
by 1E3
MHZ Sets Frequency data type and scales
by 1E6
Phase Suffix Mnem oni cs, Chap ter 4
DEG Sets Phase data type
RAD Sets Pha se dat a type and sca le s by
180/pi
Power
Code Name
IMU Sets Imaginary data type
OHM Sets Impedanc e dat a type
REU Sets Real data type
Channels, Chapter 4
CH1 Select Channel 1 as active channel
CH2 Select Channel 2 as active channel
CH3 Select Channel 3 as active channel
CH4 Select Channel 4 as active channel
CHX? Output Active channel
D13 Select dual channel display , chann els
1 & 3
D14 Select quad display, all four channels
D24 Select dual channel display , chann els
2 & 4
DSP Select single channel display
DSP? Output channel display mode
T13 Select overlaid channel 1 and 3 display
T24 Select overlaid channel 2 and 4 display
DB, DBM Sets Power data type
Time Suffi x Mnem oni cs, Chapter 4
MS Sets Time data type and scales by 1E-
3
NS Sets Time data type and scales by 1E-
9
PS Sets T ime data type and scales by 1E-
12
S Sets Time data type
US Sets Time data type and scales by 1E-
6
V ol ta ge Suf fix Mnem oni c s , Chapte r 4
MV Sets Voltag e dat a type a n d scales by
1E-3
V S ets Volta g e da t a t yp e
Miscellaneous
Display, Chapter 4
ADD Select addition as Trace Math for
active channel
APR Enter Group delay apert ure setting on
active channel
APR? Output group delay aperture setting on
active channel
ASC Autoscale the active channel display
ASP Set polar stop sweep po sition angle
ASP? Output polar stop sweep position angle
AST Set polar start sweep position angle
AST? Output polar start sweep position angle
DA T Display data only on active cha nnel
DAT? Output trace memory display mode
DIA Select Air as active d iele ctric
372XXA GPIB PM 35
PROGRAMMING CODES, GPIB QUICK
FUNCTIONAL GROUPING REFERENCE GUIDE
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
DIE Enter a dielectric value
DIM Select microporous teflon as ac tive
dielectric
DIP Select polyethylene as active dielectric
DIT Select Teflon as active dielectric
DIV Select Division as Trace Math fo r
active channel
DIX? Output dielectric cons tant
DLA Select Group Delay display for active
channel
DNM Display data normalized to Trace
Memory on active ch anne l
DTM Display Measurement data and Trace
Memory on active ch anne l
GRF? Output graph type for active channel
IMG Select Imaginary display for active
channel
ISC Select inverted compressed Sm ith
Chart for active channe l
ISE Select inverted expanded Smith chart
for active channel
ISM Select normal inverted Smith cha rt for
active channel
LIN Select Linear magnitude display for
active channel
LPH Select linear magnitude and phase
display for active channel
MAG Select log magnitude display for active
channel
MEM Display Trace M emor y on active
channel
MIN Select Subtraction as Trace Math for
active channel
MPH Select log magnitude and ph ase
display for active channel
MTH? Output trace math math type
MUL Select Multiplication as trace Math for
active channel
Code Name
OFF Set of fset level on active cha nnel
display
OFF? Output offset level on active ch anne l
display
PCP Select measurement phase polar
chart mode
PCS Select sweep position polar chart
mode
PCX? Output Polar chart mode
PHA Select phase display for active channel
PHO Set Phase Offset for display channel
PHO? Output phase Offs et for display
channel
PLG Select log polar display for active
channel
PLR Select linear polar display for active
channel
RDA Select Automatic Refe rence delay
calculatio n
RDD Set reference delay in distan ce for
active channel
RDD? Output reference delay in dista nce f or
active channel
RDT Set reference delay in time for active
channel
RDT? Output ref ere nce d e lay in time fo r
active channel
REF Set reference line for display on active
channel
REF? Output reference line for display on
active channel
REL Select real display for active channel
RIM Select Real and Imaginary display for
active channel
SCL Set Scale Resolution on active channe l
SCL? Output Scale Resolution on ac tive
channel
36 372XXA GPIB PM
GPIB QUICK PROGRAMMING CODES,
REFERENCE GUIDE FUNCTIONAL GROUPING
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
SMC Select compres sed Sm ith char t for
active channel
SME Select expanded Smith chart for active
channel
SMI Select normal smith chart for active
channel
STD Store trace to memory on active
channel
SWR Select SWR display for active channel
Measurement, Chapter 4
AH0 Turn autom atic D UT protection off
AH1 Turn autom atic D UT protection on
AHX? Output automatic DUT pr otection onoff
status
BH0 Turn bias off while in Hold
BH1 Turn bias on while in Hold
BHX? Output bias on/off during Hold status
CNTR Enter center frequency
CNTR? Output center frequency
CTN Continue sweeping from curren t poin t
CWF Turn CW on and set freq uenc y
CWF? Output CW frequency set
CWON T ur n CW on at last freq uenc y set
CWON? Output CW on/off status
CWP Enter num ber of points dra wn in CW
CWP? Output numb er of points dr awn in CW
HC0 Disable Internal IF calibra tion
HC1 Enable Interna l IF calibrat ion and
trigger an IF calibration
HCT Trigger an IF calibration
HCX? Output Internal IF calibration
enabled/disabled
HLD Instrument Hold
HLD? Hold mode query
Code Name
LAX? Sweep Phase Lock Direction
NP51 Set data points to 51
NP101 Set data point s to 101
NP201 Set data point s to 201
NP401 Set data point s to 401
NP801 Set data point s to 801
NP1601 Set data points to 1601
PW2 Set external source power level
PW2? Output external sour ce power leve l
PWR Set internal source power level
PWR? Output in te rnal source power le vel
RH0 Set RF Off while in Hold
RH1 Set RF On while in Hold
RHX? Output RF on/off during Hold status
S1 1 Measure S1 1 on active cha nnel
S12 Measure S12 on activ e chan nel
S21 Measure S21 on activ e chan nel
S22 Measure S22 on activ e chan nel
SA1 Enter Port 1 source att enua to r setting
SA1? Output Port 1 source attenuator setting
SETUP Display setup menu
SP A N Enter frequency span
SPAN? Output frequency span
SRT Start Fre quency
SRT? Output Start Frequency
STP Stop Frequency
STP? Output Stop Frequency
SWP Return to normal sweep mode
SWP? Output Sweep Mode
SXX? Output S-parameter displaye d on
active channel
TA2 Enter Port 2 test attenuator setting
372XXA GPIB PM 37
PROGRAMMING CODES, GPIB QUICK
FUNCTIONAL GROUPING REFERENCE GUIDE
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
T A2? Output Port 2 test attenuator setting
TEX Select external measurement
triggering
TIN Select internal measurem ent trigge r
TXX? Output trigger sourc e
TRS Trigg er/Res ta rt Sweep
WFS Wa it full sweep until all display data is
valid
Enhancement, Chapter 4
AOF Turn averaging off
AOF? Output avera ging on/ off status
AON Turn averaging on
AVG Turn on Averag in g and set to value
A VG ? Output Averaging count
IF1 Select 10 HZ IF bandwidth
IF2 Select 100 HZ IF bandwidth
IF3 Select 1 KHZ IF bandwidth
IF4 Select 10 KHZ IF bandwidth
IFX? IF bandwidth quer y
SOF Turn Off smoothing
SOF ? Outp u t sm o o th ing on/off status
SON Turn On smoothing and set to value
SON? Output smoothing value
Calibration, Chapter 5
A12 Simulate 12-term calibration
A8R Simulate 1-path 2-port calibrat io n
reverse pa th
A8T Simulate 1-path 2-port calibr atio n
forward path
ABT Simulate trans freq response
calibration forwa rd an d revers e
AFT Simulate trans freq respon se
calibration forwa rd path
Code Name
ARB Simulate reflection only cal ibration
both ports
ARF Simulate reflect ion on ly cal ibratio n
port 1
ARR Simulate reflect ion on ly cal ibratio n
port 2
ART Simulate trans freq respon se
calibration re ver se pat h
BBL Select broadband load for calibratio n
BBZ Enter broadband load im peda nce for
calibration
BEG Begin taki ng calibration data
BPF Enter break point frequenc y fo r 3 line
LRL calibrat ion
C12 Select 12 term calibration
C8R Select 1-path 2-port calibration
reverse pa th
C8T Select 1-path 2-port calibration
forward path
CBT Select trans freq response cal ibration
forward and reverse
CC0 Enter capacitance coef f icient 0 for
open
CC1 Enter capacitance coef f icient 1 for
open
CC2 Enter capacitance coef f icient 2 for
open
CC3 Enter capacitance coef f icient 3 for
open
CF2 Select female 2.4mm conne ctor for
current port
CF3 Select female GPC-3.5 connector for
current port
CFC Select female TNC connector for
current port
CFK Select female K connect or for curren t
port
CFN Select female Type N co nnecto r for
current port
38 372XXA GPIB PM
GPIB QUICK PROGRAMMING CODES,
REFERENCE GUIDE FUNCTIONAL GROUPING
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
CFS Select female SMA connector for
current port
CFT Select trans freq response calibration
forward path
CFV Select female V connect or for curren t
port
CM2 Select male 2.4mm conne ctor for
current port
CM3 Select male GPC-3.5 conne ctor for
current port
CMC Select male TNC connector for current
port
CMK Select male K connector for curren t
port
CMN Select male N connector for current
port
CMS Select male SMA connector for
current port
CMV Select male V connector for curren t
port
CMX? Outp u t calibrat ion met hod
CND Select user specified connector for
current port
CNG Select GPC-7 connector for curren t
port
COF Turn Off Vector Error Correction
CON Turn On Vector Error C orrection
CON? Output erro r correction on/of f st at u s
COO Enter offset for open for user specif ied
connector
COS Enter offset for shor t for user specifi ed
connector
CRB Select reflection only calibr atio n both
ports
CRF Select reflection only calibration port 1
CRR Select reflection only calibration port 2
CRT Select trans freq response calibration
reverse pa th
Code Name
CSF? Output cal start frequency
CTF? Output cal stop frequency
CWC Select CW frequency calibration data
points
CXX? Output calibration type
DFC Select discrete frequency cal ibrat io n
data points
DFD Done specifying discrete freq uenc y
ranges
DFQ Enter Single discrete frequen cy
FIL Fill defined dis cre te freque ncy r ange
FP0 Turn flat power correct ion off
FP1 Turn flat power correction on
FPX? Output flat power corre ctio n on/ of f
statu s
FRC Clear all defined discrete frequency
ranges
FRI Set discrete frequency f i ll range
increment frequency
FRP Set discrete freque ncy f ill range
number of points
FRS Set discre te freque ncy fi ll range st ar t
frequency
ISF Exclude isolation
ISN Include isolation
KEC Keep existing calibration data
LCM Select LRL calibration method
LL1 Enter length of line 1 for L RL
calibration
LL2 Enter length of line 2 for L RL
calibration
LL3 Enter length of line 3 for L RL
calibration
LLZ Enter line impedance for LRL
calibration
LM2 Select a match for the second device
during a LRM type calibration
372XXA GPIB PM 39
PROGRAMMING CODES, GPIB QUICK
FUNCTIONAL GROUPING REFERENCE GUIDE
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
LM3 Select a match for the third device
during a LRM type ca librat ion
LR2 Specify 2 line LRL calibration
LR3 Specify 3 line LRL calibration
LTC Select coaxial transmission line for
calibration
LTU Select microstrip transmission l ine fo r
calibration
LTW Select waveguide transmission line for
calibration
LTX? Output line type
MAT Select matched reflective devices
during cal
MIX Select mixed reflective devices dur ing
cal
NCS Go to next calibration st ep
NOC Select Normal Calibration dat a poin ts
OCM Select Offset short calibrat ion m ethod
P1C Select Port 1 for connector
specificat ion
P1C? Output port 1 connector type
P1P? Outpu t appro xima te power level at
port 1
P2C Select Port 2 for connector
specificat ion
P2C? Output port 2 connector type
PSP Number of power sweep s for flat
power correction
PSP? Output number of power sweeps for
flat power correction
PTS Number of points to be skipped during
flat power correction
PTS? Output number of points to be skipped
during flat power correct i on
RGZ Select reflective device greate r than Z0
RLZ Select Reflective de vice less t han Z0
Code Name
RM1 Select reference plan e at line 1
midpoint
ROL Enter reflective device offset length
RPC Repeat previous calibration
RRP Select reference plan e at reflecti on
plane
SBD Enter substrate dielect r ic for microstrip
calibration
SBT Enter substrate thickness for
microstrip calibr atio n
SCM Select standard calibration metho d
SFC Start flat test port calibration
SH1 Set offset short 1 offset length
SH2 Set offset short 2 offset length
SLD Select sliding load for calibration
TC1 Take calibration data for port 1
TC2 Take calibration data for port 2
TCD Take calibration data on one or both
ports as necess ary
TDC Select time domain harmonic
frequency cal data po in ts
TDL Throu gh DC coefficient for loss
TFE Throu gh freq uency exponent for loss
TFL Through f req uenc y coef f ic ient for loss
TLZ Enter through l ine impe danc e fo r
calibration
TOL Enter through offset length for
calibration
U10 Select 10 mil UTF calibration kit
U15 Select 15 mil UTF calibration kit
U25 Select 25 mil UTF calibration kit
USE Enter effective dielectric for micro st rip
calibration
USW Enter microstrip width for microstrip
calibration
40 372XXA GPIB PM
GPIB QUICK PROGRAMMING CODES,
REFERENCE GUIDE FUNCTIONAL GROUPING
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
USZ Enter microstrip impedance for
microstrip calibr atio n
WCO Set waveguide cu toff frequency for
user defined kit
WKD Select user defined waveguide
calibration kit
WKI Select installed waveguide calibration
kit
WSH1 Set waveguide short offset 1 for user
defined kit
WSH2 Set waveguide short offset 2 for user
defined kit
Markers, Cha pte r 6
AMKR Select active marker on all chann els
marke r mo de
BWL3 Set 3 dB for bandwidth loss value
BWLS Enter bandwidth loss value
BWLS? Output bandwidt h loss valu e
DR1 Select Marker 1 as Delta Reference
Marker
DR2 Select Marker 2 as Delta Reference
Marker
DR3 Select Marker 3 as Delta Reference
Marker
DR4 Select Marker 4 as Delta Reference
Marker
DR5 Select Marker 5 as Delta Reference
Marker
DR6 Select Marker 6 as Delta Reference
Marker
DRF Turn Delta reference mode On
DRO Turn Delta reference mode Off
DRO? Out p u t delt a ref ere nce m ode on/ of f
statu s
DRX? Output the Delta reference marker
DSF0 Disable automatic filter shape factor
calculatio n
Code Name
DSF1 Enable automatic filter shape factor
calculation
DSFX? Output automatic filter shape factor
calculation enabledisable st atus
DSQ0 Disable automatic f ilter Q calculat io n
DSQ1 Enable automatic fi lter Q calculat ion
DSQX? Output aut om at ic filt er Q calcula tion
enable/disable stat us
FLTBW? Output filter bandwidth
FLTC? Output filt er cent er fre quen cy
FLTL? Output filter loss at refere nce va lu e
FLTQ? Output filter Q
FLTS? Output filter shape fact or
FMKR Select filter parameters mark er mode
M1C Marker 1 CW frequency
M1E Marker 1 sweep/zoom end frequency,
time, or dista nce
M1S Marker 1 sweep/zoom start fre quen cy,
time, or dista nce
M2C Marker 2 CW frequency
M2E Marker 2 sweep/zoom end frequency,
time, or dista nce
M2S Marker 2 sweep/zoom start fre quen cy,
time, or dista nce
M3C Marker 3 CW frequency
M3E Marker 3 sweep/zoom end frequency,
time, or dista nce
M3S Marker 3 sweep/zoom start fre quen cy,
time, or dista nce
M4C Marker 4 CW frequency
M4E Marker 4 sweep/zoom end frequency,
time, or dista nce
M4S Marker 4 sweep/zoom start fre quen cy,
time, or dista nce
M5C Marker 5 CW frequency
372XXA GPIB PM 41
PROGRAMMING CODES, GPIB QUICK
FUNCTIONAL GROUPING REFERENCE GUIDE
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
M5E Marker 5 sweep/zoom end frequency,
time, or distance
M5S Marker 5 sweep/zoom start frequency,
time, or distance
M6C Marker 6 CW frequency
M6E Marker 6 sweep/zoom end frequency,
time, or distance
M6S Marker 6 sweep/zoom start frequency,
time, or distance
MK1 Tur n on M ark er 1 a n d set to
frequency, time or distance
MK1? Output Marker 1 frequency, time or
distance
MK2 Tur n on M ark er 2 a n d set to
frequency, time or distance
MK2? Output Marker 2 frequency, time or
distance
MK3 Tur n on M ark er 3 a n d set to
frequency, time or distance
MK3? Output Marker 3 frequency, time or
distance
MK4 Tur n on M ark er 4 a n d set to
frequency, time or distance
MK4? Output Marker 4 frequency, time or
distance
MK5 Tur n on M ark er 5 a n d set to
frequency, time or distance
MK5? Output Marker 5 frequency, time or
distance
MK6 Tur n on M ark er 6 a n d set to
frequency, time or distance
MK6? Output Marker 6 frequency, time or
distance
MKRC Select interpolated marker functionality
MKRD Select discrete marker functionality
MKRX? Outpu t inter polated/ disc rete marker
functiona lity
MKSL Marker search left
Code Name
MKSR Marker search right
MKT0 Turn marker trac king off
MKT1 Turn marker tracking on
MKTX? Output marker tracking on/off status
MR1-MR6 Select Marker 1-6 value readout
MR1?-MR6? Output Marker 1-6 on/off status
MRX? Out pu t ac tive marker number
MSFH Enter high loss value for shape fact or
calculatio n
MSFH? Output high loss value for shape factor
calculatio n
MSFH? Output high loss value for shape factor
calculatio n
MSFL Enter low loss value for shape factor
calculatio n
MSFL? Output low loss value for shape factor
calculatio n
MSR0 Select 0 as ref for marker search and
bandwidth calculation
MSRD Select delta ref marker as ref for
marker search and bandwidth
calculation
MSRM Selec t max as ref for marker search
and bandwidth calculation
MSRX? Outpu t ref selection f or marker search
and bandwidth calculation
NMKR Select normal markers on active
channel marker mode
SMKR Select marker search marker mode
SRCH Enter marker search value
SRCH? Output marker search value
XMKR? Output marker mode
Limits, Chapter 6
LFD? Output limit frequency readout delta
value
LFP Select limit frequency read-out for
phase displays
42 372XXA GPIB PM
GPIB QUICK PROGRAMMING CODES,
REFERENCE GUIDE FUNCTIONAL GROUPING
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
LFR Select limit frequ ency read out fo r
active channel
LLO T urn on lower limit and set to value
LLO? Output lower limit value for active
channel
LOL0 T urn lo wer limit off
LOL1 T ur n lower limit on at cur ren t valu e
LOLX? Output lower limit on/off status
LUP Turn on upper limit and set to value
LUP? Output upper limit value for act ive
channel
UPL0 Turn upper limit off
UPL1 Turn upper limit on at current value
UPLX? Output upper limit on/off status
Limits, Seg me nte d Limit Lin es, Chapter 6
ATTN Attach n e xt segm ent and make the
active segment
BEGN Begin next segmen t an d ma ke t he
active segment
CAS Clear active segmented l imit
vertical/horiz ontal def inition s
DIS Display active segmented limit
DIS? Outpu t active segm ent ed lim it on/off
statu s
HID Hide active segmented limit
LS1 Set lower segment ed limit 1 as the
active segment
LS2 Set lower segment ed limit 2 as the
active segment
LS3 Set lower segment ed limit 3 as the
active segment
LS4 Set lower segment ed limit 4 as the
active segment
LS5 Set lower segment ed limit 5 as the
active segment
LS6 Set lower segment ed limit 6 as the
active segment
Code Name
LS7 Set lower segmented limit 7 as the
active segment
LS8 Set lower segmented limit 8 as the
active segment
LS9 Set lower segmented limit 9 as the
active segment
LS10 Set lower segmented limit 10 as the
active segment
LSX? Output active segment ed limit
SLC Clear all segmented limits definitions
SLH Set segmented limits horizontal offset
SLH? Output segmented limits horizontal
offset
SLL0 Turn lower segm en ted limits display off
SLL1 Turn lower segmen te d limits display on
SLLX? Output lower se gment ed limit s display
on/off status
SLU0 Turn upper segmented limits display off
SLU1 Turn upper segmented limits display
on
SLUX? Output upper segmented limits display
on/off status
SL V Set segmented limits ve rtical of fse t
SL V ? Output segmente d limits vertical offset
SPH Set active segmented lim it horizon ta l
stop position
SPH? Output active segmented limit
horizontal st op pos ition
SPV Set active segmen ted limit vertical
stop position
SPV? Output active segmented limit vertical
stop position
STH Set active segm en te d limit ho rizon tal
start p o sition
STH? Output active segmented l imit
horizontal st a rt positio n
372XXA GPIB PM 43
PROGRAMMING CODES, GPIB QUICK
FUNCTIONAL GROUPING REFERENCE GUIDE
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
STV Set active segment ed limit ver tica l
start position
STV? Output active segm ent ed limit ver t ica l
start position
US1 Set upper segmented limit 1 as the
active segment
US2 Set upper segmented limit 2 as the
active segment
US3 Set upper segmented limit 3 as the
active segment
US4 Set upper segmented limit 4 as the
active segment
US5 Set upper segmented limit 5 as the
active segment
US6 Set upper segmented limit 6 as the
active segment
US7 Set upper segmented limit 7 as the
active segment
US8 Set upper segmented limit 8 as the
active segment
US9 Set upper segmented limit 9 as the
active segment
US10 Set upper segmented limit 10 as the
active segment
Limits, Pass/fail Testing, Chapter 6
LB0 Turn limits testing beep on failure off
LB1 Turn limits testing beep on failure on
LBX? Output limits test ing bee per enable
statu s
LPF? Output limit test failure status all
channels
LPF1? Output limit test failure status on
channel 1
LPF2? Output limit test failure status on
channel 2
LPF3? Output limit test failure status on
channel 3
Code Name
LPF4? Output limit test failure status on
channel 4
LT0 Turn limits testing off
LT1 Turn limits testing on
LT1? Output limits test ing ena ble stat us
LVH Set limits testing ttl level high
LVL Set limits testing ttl le vel low
LVX? Output limits testing ttl level status
Remote Onl y, Formatting an d Siz ing, Chapt er 7
DPR0 Visible data only OFD for mat
DPR1 Data pair always OFD forma t
FMA Select ASCII data transfer f or ma t
FMB Select IEEE754 64 bit data transf er
format
FMC Select IEEE754 32 bit data transfer
format
LSB Select least significant byte first binary
transf er
MSB Select most significant byte f irst binary
transf er
ONCT Output number of cal term s for current
cal
ONP Output Number of points current ly
being me asur ed
Remote Only, Input Functions, Chapter 7
IC1 Input Calibration Coefficient 1
IC2 Input Calibration Coefficient 2
IC3 Input Calibration Coefficient 3
IC4 Input Calibration Coefficient 4
IC5 Input Calibration Coefficient 5
IC6 Input Calibration Coefficient 6
IC7 Input Calibration Coefficient 7
IC8 Input Calibration Coefficient 8
IC9 Input Calibration Coefficient 9
44 372XXA GPIB PM
GPIB QUICK PROGRAMMING CODES,
REFERENCE GUIDE FUNCTIONAL GROUPING
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
IC10 Input Calibration Coef ficien t 10
IC11 Input Calibration Coefficien t 11
IC12 Input Calibration Coef ficien t 12
ICD Input corrected data for active channel
param eter
ICF Input Front Panel Setup and
Calibration data
ICL Input all applicable calibration
coefficients for cal type
IFD Input final data for active chann el
param eter
IFP Input current front pa nel setup
IFV Input frequency values
IS1 Input front panel setup 1
IS2 Input front panel setup 2
IS3 Input front panel setup 3
IS4 Input front panel setup 4
IS5 Input front panel setup 5
IS6 Input front panel setup 6
IS7 Input front panel setup 7
IS8 Input front panel setup 8
IS9 Input front panel setup 9
IS10 Input front panel setup 10
Data Tra nsf er, Output Functions, Chapter 7
OAM1 Output channel 1 active marker value
OAM2 Output channel 2 active marker value
OAM3 Output channel 3 active marker value
OAM4 Output channel 4 active marker value
OC1 Output Calibration Coefficien t 1
OC2 Output Calibration Coefficien t 2
OC3 Output Calibration Coefficien t 3
OC4 Output Calibration Coefficien t 4
OC5 Output Calibration Coefficien t 5
Code Name
OC6 Output Calibration Coefficient 6
OC7 Output Calibration Coefficient 7
OC8 Output Calibration Coefficient 8
OC9 Output Calibration Coefficient 9
OC10 Output Calibration Coefficient 10
OC11 Output Calibration Coefficient 11
OC12 Output Calibration Coefficient 12
OCD Output correc te d dat a for ac tive
channel paramet er
OCF Output Front Panel Set up and
Calibration data
OCL Output all applicable calibration
coeffic ient s for cal type
ODR Output directo ry listing of the floppy
drive
ODRH Output directory listing of the hard
drive
ODV Output distance values for time dom ain
OFD Output final data for active cha nnel
parameter
OFP Output current Front Panel Setup
OFV Output Frequency values
OID Output instrumen t identif icat ion string
OM1 Output Marker 1 value
OM2 Output Marker 2 value
OM3 Output Marker 3 value
OM4 Output Marker 4 value
OM5 Output Marker 5 value
OM6 Output Marker 6 value
ORD Output Raw dat a for ac tive channe l
paramet er
OS1 Output front panel Setup number 1
OS2 Output front panel Setup number 2
OS3 Output front panel Setup number 3
372XXA GPIB PM 45
PROGRAMMING CODES, GPIB QUICK
FUNCTIONAL GROUPING REFERENCE GUIDE
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
OS4 Output fro nt panel Set up nu mb er 4
OS5 Output fro nt panel Set up nu mb er 5
OS6 Output fro nt panel Set up nu mb er 6
OS7 Output fro nt panel Set up nu mb er 7
OS8 Output fro nt panel Set up nu mb er 8
OS9 Output fro nt panel Set up nu mb er 9
OS10 Output front panel Setup number 10
OTV Output time values for time domai n
Remote Only, Error Reporting, Chapter 7
OEL Output erro r log
OGE Outpu t exte nded descript io n of current
gpib error
OGL Outpu t exte nded descript io n of
previous gpib error
ONE Output number of lines in the error log
OSL Outpu t service log
Remote Only, IEEE488.2 Common Commands ,
Chapter 7
*CLS Clear status bytes and stru cture s
*DDT Define device t rigge r comm and
*DDT? Define device trigger query
*ESE Standard Event Status Enable
Command
*ESE? Standard Event Status Enable qu ery
*ESR? Standard Event Status Register query
*IDN? Instrument identification query
*IST? Ist message Status quer y
*OPC Operation Complete Command
*OPC? Operation Complet e qu ery
*OPT? Options installed query
*PRE Parallel Poll Register Enable
*PRE? Parallel Poll Register Enable query
*RST Reset Command
Code Name
*SRE Service Req uest Enab le
*SRE? Service Request Enable query
*STB? Status Byte query
*TRG Group Execute T r ig ger equivale nt
command
*TST? Self test and query
*WAI Wait to Continue
Remote Only, Status Reporting, Chapter 7
ILM Input limits status byte mask
IEM Input extended statu s byte mask
OEB Output extended status byte
OEM Output extended status byte mask
OLB Output limits status by te
OLM Output limits status byte mask
Hard Co p y, Action, Chapter 8
FFD Form Feed to Printer/St op prin t/plot
PFS Print Full screen image
PGR Print graph area screen image
PGT Plot graticule
PLD Plot data area only
PLH Plot header
PLM Plot Markers and Limits
PLS Plot ent ire screen
PLT Plot data traces only
PMK Print tabular data for Markers
PMN Plot Menu
PMT Print Tabular dat a for T race s an d
Markers
PST Stop Print/Plot
PTB Print tabular data for Traces
Hard Copy, Setup, Chapter 8
DPN Enter pen nu mb er for dat a
GPN Enter pen number for graticule
46 372XXA GPIB PM
GPIB QUICK PROGRAMMING CODES,
REFERENCE GUIDE FUNCTIONAL GROUPING
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
HD0 Tur n off tabular dat a header s and
page form at t i ng
HD1 T urn on t abular data hea der s and
page form at t i ng
HPN Enter pen numb er for header
LAND Select landscape mode for output plot
LDT Enter label string f or date/ tim e
LDT? Output label string for date/time
LID Enter label string for device ID
LID? Output label string fo r device ID
LMS Enter label string for model/s erial
numb er
LMS? Output label string for model/ser ial
numb er
LNM Enter label st ring for oper at or’s name
LNM? Output label string for operator’s name
LOC Enter label string for oper ator’s
comment
LOC? Output label string for operator’s
comment
MPN Enter pen nu mb er for marker s and
limits
PBL Select 1/4 size plot, bottom left corner
PBR Select 1/4 size plot, bottom right corner
PFL Select Full-size plot
PLO? Output plot mode, por t rait or landscape
PORT Select port rait mode f or output plot
Code Name
PT7 Set T abular Printout points sk ipped t o 7
PT8 Set T abular Printout points sk ipped t o 8
PT9 Set T abular Printout points sk ipped t o 9
PTL Select 1/4 size plot, top left corner
PTR Select 1/4 size plot, top right cor ner
SPD Enter pen speed percentag e
TPN Enter pen num ber for trac e over la y
data
System State, Chapter 8
BC0 Turn CRT display of f
BC1 Turn CRT display on
BCX? Output CRT display status
DC1 Display channel 1 and 2 operatin g
paramet ers
DC3 Display channel 3 and 4 operatin g
paramet ers
DCP1 Display Calibration Paramet ers 1st
page
DCP2 Display Calibration Paramet ers 2nd
page
DD0 Tu rn Data drawing off
DD1 Turn Data dr awing on
DD1? Output Data Drawing on/off stat us
DF2 Display 2.4m m female co nnec to r
inform ation
DF3 Display GPC-3 .5 female co nnec to r
inform ation
PT0 Set Tabular Printout points skipped to 0
PT1 Set Tabular Printout points skipped to 1
PT2 Set Tabular Printout points skipped to 2
PT3 Set Tabular Printout points skipped to 3
PT4 Set Tabular Printout points skipped to 4
PT5 Set Tabular Printout points skipped to 5
PT6 Set Tabular Printout points skipped to 6
DFK Display K fema le conne ctor
inform ation
DFN Display N female connector
inform ation
DFP Display Fr ont panel instrument state
DFS Display SMA female connector
inform ation
DFT Display TNC female connector
inform ation
372XXA GPIB PM 47
PROGRAMMING CODES, GPIB QUICK
FUNCTIONAL GROUPING REFERENCE GUIDE
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
DFV Display V female connect or
information
DG7 Display GPC-7 Male connector
information
DGS Display GPIB status information
DM2 Display 2.4mm male connector
information
DM3 Display GPC-3.5 male connector
information
DMK Display K male connector inform atio n
DMN Display N male connector informatio n
DMS Display SMA male connector
information
DMT Display TNC male connector
information
DMV Display V male connector inform atio n
DWG Display Waveguide parameters
FOF Blank frequency information
FON Display frequency information
FOX? Output frequen cy informat ion on /o ff
statu s
RST0 Reset instrument plus front panel
memories and reserved parameters
RST1 Reset instrument plus front panel
memories
RTL Return to Loca l
Colorizatio n , Cha pte r 8
ANNCOL Enter the color number for anno tation
and menu t ext
ANNCOL? Annotation and menu text color
number query
DATCOL Enter the color number for data
DATCOL? Data color number query
GRTCO L Enter the color number for th e graticule
GRTCOL? Graticule color nu mber query
Code Name
LAYCOL? Ove rlay da ta color nu mb er query
MKRCOL Enter the color number for th e
markers, time or distance
MKRCOL? Markers color number query
MNUCOL Enter the color number for the me nu
headers
MNUCOL? Menu header color number query
TRCCOL Enter the color n um ber for memory
data
TRCCOL? Memory data color number quer y
Save and Recall, Chapter 8
RC1 Recall Front Panel Set up from
memory number 1
RC2 Recall Front Panel Set up from
memory num ber 2
RC3 Recall Front Panel Set up from
memory num ber 3
RC4 Recall Front Panel Set up from
memory num ber 4
RC5 Recall Front Panel Set up from
memory num ber 5
RC6 Recall Front Panel Set up from
memory num ber 6
RC7 Recall Front Panel Set up from
memory num ber 7
RC8 Recall Front Panel Set up from
memory num ber 8
RC9 Recall Front Panel Set up from
memory num ber 9
RC10 Recall Front Panel Setup from
memory num ber 10
SV1 Save front pan el set up t o
memorynum be r 1
SV2 Sav e front pan el s et up to me mo ry
numb er 2
SV3 Sav e front pan el s et up to me mo ry
numb er 3
LAYCOL Enter the color number for overlay dat a
48 372XXA GPIB PM
GPIB QUICK PROGRAMMING CODES,
REFERENCE GUIDE FUNCTIONAL GROUPING
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
SV4 Sav e front pan el s et up to me mo ry
numb er 4
SV5 Sav e front pan el s et up to me mo ry
numb er 5
SV6 Sav e front pan el s et up to me mo ry
numb er 6
SV7 Sav e front pan el s et up to me mo ry
numb er 7
SV8 Sav e front pan el s et up to me mo ry
numb er 8
SV9 Sav e front pan el s et up to me mo ry
numb er 9
SV10 Save fr ont pan el set up t o me mo ry
number 10
Disk Functions, Chapter 8
CPYALCFH Copy ALC Cal file from flo ppy to hard
disk
CPYALCHF Copy ALC Cal file from hard to flop py
disk
CPYALLFH Copy Combined Hardwar e Cal file
from floppy to hard disk
CPYALLHF Copy Combined Hardwar e Cal file
from hard to floppy disk
CPYCALFH Copy Calibration/Front Pane l Set up
from floppy to hard disk
CPYCALHF Copy Calibration/Front Pane l Set up
from hard to floppy disk
CPYDATFH Copy Tabular Data file from floppy to
hard disk
CPYDATHF Copy Tabular Data file from hard to
floppy disk
CPYELGFH Copy Error Log file from floppy t o hard
disk
CPYELGHF Copy Error Log file from hard to floppy
disk
CPYFREFH Copy Frequency Cal file from flo ppy to
hard disk
CPYFREHF Copy Frequency Cal file from hard t o
floppy disk
Code Name
CPYLOGFH Copy Service Log file from floppy to
hard disk
CPYLOGHF Copy Service Log file from hard to
floppy disk
CPYNRMFH Copy Tra ce M em ory Fi le from f loppy
to har d disk
CPYNRMHF Copy Trace Mem ory File from hard to
floppy disk
DELALC Delete ALC Cal file from floppy disk
DELALCH Delete ALC Cal file from hard disk
DELALL Delete Combined Har dwar e Cal file
from floppy disk
DELALLH Delete Combined Hardware Cal file
from hard disk
DELCAL Delete Calibration/Front Panel Setup
from floppy disk
DELCALH Delete Calibration/Front Pane l Set up
from hard disk
DELDA T Delete Tabular Data file from floppy
disk
DELDA T H Delete Tabular Data file from hard disk
DELELG Delete Error Log file from floppy disk
DELELGH Delete Error Log file from hard disk
DELFRE Delete Frequency Cal file from floppy
disk
DELFREH Delete Frequency Cal file from hard
disk
DELLOG Delete Service Log file from floppy disk
DELLOGH Delete Service Log file from hard disk
DELNRM Delete Trace Memory File from floppy
disk
DELNRMH Delete Trace Memory File from hard
disk
INT Initialize (format) floppy disk
LKT Load calibration kit informat ion f rom
floppy disk
PDR Print directory listin g of the floppy drive
372XXA GPIB PM 49
PROGRAMMING CODES, GPIB QUICK
FUNCTIONAL GROUPING REFERENCE GUIDE
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
PDRH Print directory listing of the hard dr ive
RCLALC Recall ALC Cal file from floppy disk
RCLALCH Recall ALC Cal file f r om har d d isk
RCLALL Recall Combined Hardware Cal file
from floppy disk
RCLALLH Recall Combined Hardware Cal file
from hard disk
RCLCAL Recall Calibration/Front Panel Setup
from floppy disk
RCLCALH Recall Calibration/Front Panel Setup
from hard disk
RCLDAT Recall Tabular data file from floppy
disk to printer
RCLDATH Recall Tabular data file from hard disk
to printer
RCLELG Recall Error Log fi le from floppy disk
to printer
RCLELG H Reca l l Error Log f ile from hard disk to
print er
RCLFRE Recall Frequency Cal fi le from floppy
disk
RCLFREH Recall Frequency Cal file from hard
disk
RCLLOG Recal l Service Log file f rom flo ppy
disk to printer
RCLLOG H Recall Service Log file from har d disk
to printer
RCLNRM Recall Trace Memory File from flo ppy
disk
RCLNRMH Recall Trace Memory File from hard
disk
SAVALC Save ALC Cal to floppy disk
SAVALCH Save ALC Cal to hard disk
SAVALL Save Combined Hardware Cal to
floppy disk
SAVALLH Save Combined Hardware Cal to hard
disk
Code Name
SAVCAL Sav e Calibration/Front Panel Setup to
floppy disk
SAVCALH Save Calibration/Fr ont Panel Setup to
hard disk
SAVDAT Save T abular Dat a to flo ppy d is k
SAVDATH Save Tabular Data to hard disk
SAVELG Save Error Log to floppy disk
SAVELGH Save Error Log to hard disk
SAVFRE Save Frequency Cal to floppy disk
SAVFREH Save Frequency Cal to hard disk
SAVLOG Save Service Log to floppy disk
SAVLOGH Save Service Log to hard disk
SAVNRM Save Trace Memory to floppy disk
SAVNRMH Save Trace Memory to hard disk
Diagnostics, Chapter 8
ALC Perform ALC loop internal calibration
CSL Clear service log
DGT1 Display 1st CRT test pattern
DGT2 Display 2nd CRT test pattern
DGT3 Display 3rd CRT test pattern
DRL Diagnostic read latch
DVM Set DVM channe l
DWL Diagnostic write latch
EDG End diagnostics mode
EKT External keyboard test
EXD Display external a/d input
FLC Source frequency linearity internal
calibration
FPT Front panel keypad test
IFB Test 1st IF band pass
LKS0 Disable lock search mode
LKS1 Enable lock sea rch mode
LO11 LO1 phase lock voltage test
50 372XXA GPIB PM
GPIB QUICK PROGRAMMING CODES,
REFERENCE GUIDE FUNCTIONAL GROUPING
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
LO12 LO1 d/a voltage test
LO21 LO2 main phase lock volta ge test
LO22 LO2 of fset pha se lock vo lta g e test
LO23 LO2 dds pha se lock vo lta g e test
LO24 LO2 main d/a voltage test
LO25 LO2 offset d/a voltage test
NRD Display non-ratioed parameters on 4
channels
PEL Prin t the er ror log
PRT? Printer peripheral test and query
PSL Print the se rvice log
SDG Start diagnostics mode
SDR Select standard receiver mod e
SL1 Select Source lock mode with GPIB
source cont rol On
SRC1 Source linearity voltage test
SRC2 Source power voltage test
ST1 Select set on mode with GPIB source
control on
TK1 Select tracking mode with GPIB
source cont rol On
Special Appl i cations, Time Domain, Chapter 9
DBP Select Distance Bandpass mode for
active channel
DCA Select Automatic DC term calculation
for lowpass
Code Name
DLP Select Distance lowpass mode for
active channel
DPI Select Distance phasor imp ulse mode
for active channel
FGT Select frequency with time ga te for
active channel
FQD Select Frequen cy Domain f or active
channel
GCT Enter gate cent er value time or
distance
GCT? Output gate center value
GDS Gate symbols displayed on active
channel
GLS Select low sid elobe gate shape
GMS Select minimum sidelobe gate shap e
GNM Select nominal gat e shape
GOF Turn Off Gating on active chan nel
GOF? Output gating m ode on activ e chann el
GON Turn On Gating on active chan nel
GRT Select Rectangular gate shape
GSN Enter gate span value time or dis tance
GSN? Output gate span value
GSP Enter gate stop value time or distanc e
GSP? Output gate stop value
GST Enter gate start value time or distanc e
GST? Output gate start va lu e
DCO Select Open for DC term for lowpass
DCS Select Short for DC term for lowpass
DCV Enter value for DC term for lowpass
DCV? Output lowpass DC term value
DCX? Output lowpass DC term selection
DCZ Select Line Impedance for DC term for
lowpass
DDX? Output active channel domain
parameter (frequen cy dist anc e or time)
GSX? Output gate shape
LPI Select lowpass impulse response for
active channel
LPS Select lowpass step respons e for
active channel
LPSX? Output lowpass response (impulse or
step) for active channel
MRR Restore original Marker range
372XXA GPIB PM 51
PROGRAMMING CODES, GPIB QUICK
FUNCTIONAL GROUPING REFERENCE GUIDE
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
TBP Select time bandpass mode for active
channel
TDDIST Set time domain parameter to
distance for active channe l
TDDIST? Output active channel time domain
parameter (time or distance)
TDPI0 Turn phasor impulse respo nse off for
active channel
TDPI1 Turn phasor impulse respo nse on for
active channel
TDPIX? Output phasor impulse on/ off status
for active channel
TDTIME Set time domain parameter to time for
active channel
TDX? Output domain mode for active
channel
TLP Select time lowpass mode for active
channel
TPI Select time phasor impulse m ode f or
active channel
WLS Select low sidelobe window shape
WMS Select minimum sidelobe window
shape
WNM Select nominal window shape
WRT Select rectangular window shape
WSX? Output window shape
ZCT Enter zoom range cent er valu e tim e or
distance
ZCT? Output zoom range center value
ZSN Enter zoom range sp an value time or
distance
ZSN? Output zoom range span value
ZSP Enter zoom range stop value time or
distance
ZSP? Output zoom range stop value
ZST Enter zoom range st ar t value time or
distance
Code Name
ZST? Output zoom range start value
Special Applications, Multipl e Source Co ntrol,
Chapter 9
BD1 Select band 1 for definition
BD2 Select band 2 for definition
BD3 Select band 3 for definition
BD4 Select band 4 for definition
BD5 Select band 5 for definition
BSP Enter band sto p frequency
BSP? Output band stop frequency
BST Enter band start frequency
BST? Output band start frequency
CLB Clear all multiple source band
definitions
ECW Select CW operation for componen t
being edited
ED1 Edit Source 1 equation
ED2 Edit Source 2 equation
EDR Edit receiver equation
EDV Set divisor for equation being edited
EDV? Output divisor for equation being
edited
EML Set multiplier for equation being edited
EML? Output multiplier for equat ion being
edited
EOS Set offset frequency f or equation
being edited
EOS? Output offset frequ ency for equation
being edited
ESW Select sweep operation for component
being edited
EXW? Output multiple source sweep flag for
equation being edite d
MS0 Turn Multiple Source mode Off
MS1 Turn Multiple Source mode On
52 372XXA GPIB PM
GPIB QUICK PROGRAMMING CODES,
REFERENCE GUIDE FUNCTIONAL GROUPING
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
MSD Select multiple Sourc e define mode
MSX? Output multiple source mode
on/off/define
SVB Save current band definit io ns
Special Applicat io ns, Rear Panel Analog Out put,
Chapter 9
RPO Set rear panel dc voltage value
RPO? Output rear panel dc voltage to gpib
RV0 Turn Rear panel outpu t voltag e Of f
RV1 Turn Rear panel outpu t voltag e On
RV1? Output Rear panel output volt age
on/o ff status
RVD Set Rear panel output mode to d c
value
RVH Set Rear panel output mode to
horizontal
RVL Set Rear panel output mode to lock
direction
RVV Set Rear panel output mode to vertical
RVX? Output rear panel out pu t mode
VSP Stop voltage value
VSP? Output stop voltage value
VST Start voltage value
VST? Output start voltage value
Obsolete Mnemonics Supported For
Backwards Compat abil ity
BLU Select blue as third plane color
CMT Same as CM
CSB Same as *CLS
CYN Select cyan as third plane color
DBL Same as DB
DCP Same as DCP1
DEC Same as DELCAL
DECH Same as DELCALH
Code Name
DED Same as DELDAT
DEDH Same as DELDAT H
DEN Same as DELNRM
DENH Same as DELNRMH
DGT Same as DGT 1
FHI Same as NP1601
FLO Same as NP101
FME Same as NP401
ICA Same as IC10
ICB Same as IC11
ICC Same as IC12
IFA Same as IF4
IFM Same as IF1
IFN Same as IF3
IFR Same as IF2
IPM Same as *SRE
MMT Same as MM
MTR Same as M
NSC Same as NS
OCA Same as OC10
OCB Same as OC11
OCC Same as OC1 2
OPB Same as *STB?
PSC Same as PS
PW1 Same as PWR
RCK Same as RCLNRM
RCKH Same as RCLNRMH
RLD Same as RCLCAL
RLDH Same as RCLCALH
RST Same as *RST
RTB Same as RCLDAT
RTBH Same as RCLDATH
372XXA GPIB PM 53
PROGRAMMING CODES, GPIB QUICK
FUNCTIONAL GROUPING REFERENCE GUIDE
Table 2. 372XXA Progr ammin g Code, Functional Grouping
Code Name
SDK Same as SAVNRM
SDKH Same as SAVNRMH
STO Same as SAVCAL
STOH Same as SAVCALH
TDD Same as SAVDAT
TDDH Same as SAVDATH
TST Same as *TST?
Code Name
USC Same as US
VLT Same as V
XM3 Sets Unitless data type and scales by
1E-3
XX1 Sets Unitless da ta typ e
XX3 Sets Unitless da ta type and sc ales by
1E3
54 372XXA GPIB PM
Loading...