Use & Care Instructions
MODEL BDC
Item pictured may differ from actual product
El artículo ilustrado puede diferir del producto real
Il est possible que l’article sur la photo soit différent du produit réel
LITERATURE PACKET #04677
2 3
6. Keep the cord away from heated surfaces.
7. Never drop or insert any object into any opening.
8. Do not use outdoors or operate where aerosol (spray) products
are being used or where oxygen is being administered.
9. Do not use this appliance with a damaged or broken blade or
comb, as injury to the skin may occur.
10.
To disconnect turn control to OFF then remove plug from outlet.
11. WARNING: During use, do not place or leave appliance
where it may be (1) damaged by an animal or (2) exposed
to the weather.
12. This appliance is intended for trimming purposes only.
SAVE THESE INSTRUCTIONS
THIS PRODUCT INTENDED FOR HOUSEHOLD USE
OPERATING INSTRUCTIONS
To reduce the risk of electric shock, this appliance has a polarized plug (one
blade is wider than the other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install the proper outlet. Do not change the
plug in any way.
Plug cord into electrical outlet, operate at 120 volt, 60 cycle AC electrical current
or as noted on the unit.
2-SPEED OPERATION
Your Andis clipper is equipped with two cutting speeds. The speeds are adjusted
using the slide switch actuator on the top of the unit (Figure A). Setting "O"
indicates the off position, Setting "1" is low speed and Setting "2" is high
speed. After using your Andis clipper, rewrap cord and store in a safe place.
REMOVING BLADE SET
To remove blade set, first make sure your clipper motor is switched OFF. Push
blade release mechanism under blade hinge (Figure B). While holding down the
blade release mechanism, push down on blade, then gently pull the blade
forward (Figure C), and slide it off the blade hinge. If your blade hinge should
snap closed and is flush with the clipper, use a small standard screwdriver to pry
the tongue of the hinge out (Figure D). NOTE: Hair may accumulate in the front
cavity of the housing under the blade. If this happens, you can clean out the hair
by brushing out the cavity with a small brush or an old toothbrush while the
blade is off the clipper.
ENGLISH
Please read the following instructions before using your new Andis
clipper. Give it the care that a fine, precision built instrument
deserves and it will give you years of service.
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should
always be followed, including the following: Read all
instructions before using the Andis clipper.
DANGER: To reduce the risk of electric shock:
1. Do not reach for an appliance that has fallen into water.
Unplug immediately.
2. Do not use while bathing or in a shower.
3. Do not place or store appliance where it can fall or be pulled
into a tub or sink. Do not place in or drop into water or other
liquid.
4. Always unplug this appliance after use.
5. Unplug this appliance before cleaning, removing or
assembling parts.
WARNING: To reduce the risk of burns, fire, electric
shock, or injury to persons:
1.
An appliance should never be left unattended when plugged in.
2. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
3. Children should be supervised to ensure that they do not play
with the appliance.
4. Use this appliance only for its intended use as described in this
manual. Do not use attachments not recommended by Andis.
5. Never operate this appliance if it has a damaged cord or
plug, if it is not working properly, if it has been dropped or
damaged, or dropped into water. Return the appliance to an
Andis authorized service station for examination and repair.
4 5
REPLACING OR CHANGING BLADE SET
To replace or change your blade set, slide the blade bracket onto the hinge of
the clipper (Figure E) and with the clipper turned ON, push the blade towards
the clipper to lock into position.
USER MAINTENANCE
The internal mechanism of your motor clipper has been permanently lubricated
by the factory. Other than the recommended maintenance described in this
manual, no other maintenance should be performed, except by Andis Company,
or an Andis authorized service station. To find an Andis authorized service
station near you log on to www.andis.com or contact our customer service
department at 1-800-558-9441.
BLADE TEMPERATURE
Due to the high speed nature of Andis clippers, please check for blade heat
often, especially on close cutting blades. If blades are too hot, dip the blades
only into Andis Blade Care Plus or apply Andis Cool Care Plus and then Andis
Clipper Oil. With this detachable blade unit, you can change your blade in order
to maintain a comfortable temperature; using multiple blades of the same size is
popular among groomers.
CARE AND SERVICING OF YOUR ANDIS CLIPPER BLADES
Blades should be oiled before, during, and after each use. If your clipper blades
leave streaks or slow down, it’s a sure sign blades need oil. Place a few drops of
Andis Clipper Oil on the front and side of the cutter blades (Figure F). Wipe
excess oil off blades with a soft dry cloth. Spray lubricants contain insufficient oil
for good lubrication, but are an excellent clipper blade coolant. Always replace
broken or nicked blades to prevent injury. You can clean the excess hair from
your blades by using a small brush or worn out tooth brush. To clean the blades
we suggest to immerse the blades only into a shallow pan of Andis Blade Care
Plus, while the clipper is running. Any excess hair and dirt that has accumulated
between the blades should come out. After cleaning, turn your clipper OFF and
dry blades with a soft, dry cloth and start clipping again.
If upon cleaning your blades you find that the blades will still not cut, there may
be a few fine pieces of hair trapped between the upper and lower blade. If this
happens, you will need to snap the blade off the clipper. Proceed to slide the
upper blade to one side, without loosening the tension spring or moving the
upper blade completely out from under the tension spring (See Figure G for
position of blade). Wipe the surface between the blades clean with a dry cloth,
then place a drop of clipper oil where the upper and lower blades meet and also
in the guide slot of the tension spring (Figure G). Now slide the upper blade to
the opposite side of the lower blade and repeat this process. After completing
this procedure, slide the upper blade, centering it over the lower blade. Handle
or store your Andis Clipper with the blades down so excess oil will not run into
the clipper case.
A
D
G
J
B
E
H
K
C
F
I
L
OIL
CORRECT INCORRECT
6 7
CHANGING THE BLADE DRIVE ASSEMBLY
If your clipper blades no longer cut properly (be sure to try more than one blade,
since the blade currently being used may be dull), it could be that your blade
drive assembly needs replacement.
To change the blade drive assembly:
1. Remove blade set (Figure C).
2. Remove drive cap (Figure H).
3. Remove blade drive mounting screws (Figure I).
4. NOTE: Before removing blade drive assembly, note the way it is positioned
(this will help you in reassembly). Remove blade drive assembly (Figure J).
5. Drive bearing should be at its lowest position, if not, move it with your finger
to lowest position (Figures K & L).
6. Put on new drive assembly, align screw holes and press down (Figure J).
7. Reassemble blade drive by mounting screws (Figure I).
8. Replace drive cap (Figure H).
9. Replace blade (Figure E).
FACTORY REPAIR SERVICE
When the blades of your Andis clipper become dull after repeated use, it is
advised to purchase a new set of blades available through your Andis supplier
or through an Andis authorized service station. Some blade sets can be
resharpened – contact Andis Company for information on resharpening. To find
an Andis authorized service station near you log on to www.andis.com or
contact our customer service department at 1-800-558-9441.
Caution: Never handle your Andis clipper while you are operating a water
faucet, and never hold your clipper under a water faucet or in water. There is
danger of electrical shock and damage to your clipper. Andis Company will
not be responsible in case of injury due to this carelessness.
Lea las instrucciones siguientes antes de utilizar su nueva máquina
Andis. Trátela como se merece un instrumento delicado y de precisión,
y le dará servicio durante muchos años.
PRECAUCIONES IMPORTANTES
Al usar un artefacto eléctrico, siempre deben seguirse ciertas
precauciones básicas, que incluyen la siguiente: Lea todas
las instrucciones antes de usar la máquina Andis.
PELIGRO: Para reducir el riesgo de descarga eléctrica:
1. Si un artefacto se ha caído al agua, no trate de sacarlo.
Desenchúfelo inmediatamente.
2. No lo utilice al bañarse una bañera o bajo la regadera.
3. No coloque ni almacene el artefacto donde pueda
caerse en una bañera o un lavabo, o ser halado dentro
de éstos. No la coloque ni la deje caer en agua u otro
líquido.
4. Siempre desenchufe este artefacto después de usarlo.
5. Desenchufe este artefacto antes de limpiar, desmontar
o montar las piezas.
ADVERTENCIA: Para reducir el riesgo de
quemaduras, incendio, descarga eléctrica o lesiones a las
personas:
1. Un artefacto nunca debe dejarse desatendido mientras
está enchufado.
2. Este artefacto eléctrico no debe ser usado por personas
(incluyendo niños) con limitada capacidad física, sensorial o
mental, o que no tengan experiencia o conocimientos, a
menos que alguna persona responsable de su seguridad
los supervise o les haya dado instrucciones con respecto al
uso del aparato.
3. Es necesario supervisar a los niños para asegurarse de que
no jueguen con el aparato eléctrico.
SPANISH
Loading...