Analog Devices AD584T, AD584L, AD584K, AD584J Datasheet

Pin Programmable

7

8

1

4

5

6

3

2

CAP

V

BG

STROBE

COMMON

TAB

10.0V

5.0V

2.5V

V+

AD584

TOP VIEW

(Not to Scale)

a

FEATURES
Four Programmable Output Voltages:

10.000 V, 7.500 V, 5.000 V, 2.500 V
Laser-Trimmed to High Accuracies
No External Components Required
Trimmed Temperature Coefficient:

5 ppm/ⴗC Max, 0ⴗC to 70ⴗC (AD584L)

15 ppm/ⴗC Max, –55ⴗC to +125ⴗC (AD584T)
Zero Output Strobe Terminal Provided
Two Terminal Negative Reference

Capability (5 V and above)
Output Sources or Sinks Current
Low Quiescent Current: 1.0 mA Max
10 mA Current Output Capability
MIL-STD-883 Compliant Versions Available

GENERAL DESCRIPTION

The AD584 is an eight-terminal precision voltage reference offer­ing pin-programmable selection of four popular output voltages:

10.000 V, 7.500 V, 5.000 V and 2.500 V. Other output voltages,
above, below or between the four standard outputs, are available
by the addition of external resistors. Input voltage may vary between

4.5 V and 30 V.

Laser Wafer Trimming (LWT) is used to adjust the pin­programmable output levels and temperature coefficients,
resulting in the most flexible high precision voltage reference
available in monolithic form.

In addition to the programmable output voltages, the AD584 offers
a unique strobe terminal which permits the device to be turned
on or off. When the AD584 is used as a power supply reference,
the supply can be switched off with a single, low-power signal.
In the “off” state the current drain by the AD584 is reduced to
about 100 µA. In the “on” state the total supply current is typi-
cally 750 µA including the output buffer amplifier.

The AD584 is recommended for use as a reference for 8-, 10-,
or 12-bit D/A converters which require an external precision
reference. The device is also ideal for all types of A/D convert­ers of up to 14-bit accuracy, either successive approximation or
integrating designs, and in general can offer better performance
than that provided by standard self-contained references.

The AD584J, K, and L are specified for operation from 0°C to
70°C; the AD584S and T are specified for the –55°C to +125°C
range. All grades are packaged in a hermetically sealed eight­terminal TO-99 metal can; the AD584 J and K are also available
in an 8-lead plastic DIP.

Precision Voltage Reference

AD584*

PIN CONFIGURATIONS

8-Lead TO-99

8-Lead DIP

1

10.0V

5.0V

2.5V

AD584

2

TOP VIEW

3

(Not to Scale)

4

PRODUCT HIGHLIGHTS

1. The flexibility of the AD584 eliminates the need to design-in
and inventory several different voltage references. Further
more one AD584 can serve as several references simultaneously
when buffered properly.

2. Laser trimming of both initial accuracy and temperature coeffi­cient results in very low errors over temperature without the
use of external components. The AD584LH has a maximum
deviation from 10.000 V of ±7.25 mV from 0°C to 70°C.

3. The AD584 can be operated in a two-terminal “Zener” mode
at 5 V output and above. By connecting the input and the
output, the AD584 can be used in this “Zener” configuration
as a negative reference.

4. The output of the AD584 is configured to sink or source
currents. This means that small reverse currents can be toler­ated in circuits using the AD584 without damage to the refer­ence and without disturbing the output voltage (10 V, 7.5 V,
and 5 V outputs).

5. The AD584 is available in versions compliant with MIL-STD-

883. Refer to the Analog Devices Military Products Databook
or current AD584/883B data sheet for detailed specifications.

8

+V

7

CAP

6

V

BG

5

STROBECOMMON

*Protected by U.S. Patent No. 3,887,863; RE 30,586.

REV. B

Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] www.analog.com
Fax: [phone] © Analog Devices, Inc., 2001

AD584–SPECIFICATIONS

(@ VIN = 15 V and 25ⴗC

unless otherwise noted.

)

Model AD584J AD584K AD584L

Min Typ Max Min Typ Max Min Typ Max Unit

OUTPUT VOLTAGE TOLERANCE

Maximum Error

1

for Nominal

Outputs of:

10.000 V ⴞ30 ⴞ10 ⴞ5 mV

7.500 V ⴞ20 ⴞ8 ⴞ4 mV

5.000 V ⴞ15 ⴞ6 ⴞ3 mV

2.500 V ⴞ7.5 ⴞ3.5 ⴞ2.5 mV

OUTPUT VOLTAGE CHANGE

Maximum Deviation from 25°C

Value, T

MIN

to T

MAX

2

10.000 V, 7.500 V, 5.000 V Outputs 30 15 5 ppm/°C

2.500 V Output 30 15 10 ppm/°C

Differential Temperature

Coefficients Between Outputs 5 3 3 ppm/°C

QUIESCENT CURRENT 0.75 1.0 0.75 1.0 0.75 1.0 mA

Temperature Variation 1.5 1.5 1.5 µA/°C

TURN-ON SETTLING TIME TO 0.1% 200 200 200 µs

NOISE

(0.1 Hz to 10 Hz) 50 50 50 µV p-p

LONG-TERM STABILITY 25 25 25 ppm/1000 Hrs

SHORT-CIRCUIT CURRENT 30 30 30 mA

LINE REGULATION (No Load)

15 V ≤ VIN ≤ 30 V 0.002 0.002 0.002 %/V
(V

2.5 V) ≤ VIN ≤ 15 V 0.005 0.005 0.005 %/V

OUT

LOAD REGULATION

0 ≤ I

≤ 5 mA, All Outputs 20 50 20 50 20 50 ppm/mA

OUT

OUTPUT CURRENT

VIN ≥ V

OUT

2.5 V
Source @ 25°C101010mA
Source T
Sink T

MIN

MIN

to T

to T

MAX

MAX

55 5mA
55 5mA

TEMPERATURE RANGE

Operating 0 70 0 70 0 70 °C
Storage –65 +175 –65 +175 –65 +175 °C

PACKAGE OPTION

3

TO-99 (H-08A) AD584JH AD584KH AD584LH
Plastic (N-8) AD584JN AD584KN

NOTES

1

At Pin 1.

2

Calculated as average over the operating temperature range.

3

H = Hermetic Metal Can; N = Plastic DIP.

Specifications subject to change without notice.
Specifications shown in boldface are tested on all production units at final electrical
test. Results from those tests are used to calculate outgoing quality levels. All min
and max specifications are guaranteed, although only those shown in boldface are
tested on all production units.

–2–

REV. B

AD584

Model AD584S AD584T

Min Typ Max Min Typ Max Unit

OUTPUT VOLTAGE TOLERANCE

Maximum Error

Outputs of:

10.000 V ⴞ30 ⴞ10 mV

7.500 V ⴞ20 ⴞ8 mV

5.000 V ⴞ15

2.500 V ⴞ7.5 ⴞ3.5 mV

OUTPUT VOLTAGE CHANGE

Maximum Deviation from 25°C

Value, T

10.000 V, 7.500 V, 5.000 V Outputs 30 15 ppm/°C

2.500 V Output 30 20 ppm/°C

Differential Temperature

Coefficients Between Outputs 5 3 ppm/°C

QUIESCENT CURRENT 0.75 1.0 0.75 1.0 mA

Temperature Variation 1.5 1.5 µA/°C

TURN-ON SETTLING TIME TO 0.1% 200 200 µs

NOISE

(0.1 Hz to 10 Hz) 50 50 µV p-p

LONG-TERM STABILITY 25 25 ppm/1000 Hrs

SHORT-CIRCUIT CURRENT 30 30 mA

LINE REGULATION (No Load)

15 V ≤ VIN ≤ 30 V 0.002 0.002 %/V
(V

2.5 V) ≤ VIN ≤ 15 V 0.005 0.005 %/V

OUT

LOAD REGULATION

0 ≤ I

≤ 5 mA, All Outputs 20 50 20 50 ppm/mA

OUT

OUTPUT CURRENT

≥ V

V

IN

OUT

Source @ 25°C1010mA
Source T
Sink T

TEMPERATURE RANGE

Operating –55 +125 –55 +125 °C
Storage –65 +175 –65 +175 °C

PACKAGE OPTION

TO-99 (H-08A) AD584SH AD584TH

NOTES

1

At Pin 1.

2

Calculated as average over the operating temperature range.

Specifications subject to change without notice.
Specifications shown in boldface are tested on all production units at final electrical
test. Results from those tests are used to calculate outgoing quality levels. All min
and max specifications are guaranteed, although only those shown in boldface are
tested on all production units.

MIN

to T

MIN

2.5 V

MIN

to T

1

to T

for Nominal

2

MAX

MAX

MAX

±

6 mV

55mA
55mA

REV. B

–3–

AD584

ABSOLUTE MAXIMUM RATINGS

Input Voltage VIN to Ground . . . . . . . . . . . . . . . . . . . . . . 40 V

Power Dissipation

@ 25°C . . . . . . . . . . . . . . . . . . . . . 600 mW

METALIZATION PHOTOGRAPH

Dimensions shown in inches and (mm).

Operating Junction Temperature Range . . . –55°C to +125°C

Lead Temperature (Soldering 10 sec) . . . . . . . . . . . . . . 300°C

Thermal Resistance

Junction-to-Ambient (H-08A) . . . . . . . . . . . . . . . 150°C/W

ORDERING GUIDE

Ouput Temperature No. of Temperature
Voltage Initial Accuracy Coefficient Package Package Parts per Range

Model V

O

mV % ppm/ⴗC Description Option Package ⴗC

AD584L 2.5 ± 2.5 0.10 10 TO-99 H-8 100 0 to 70
AD584K 2.5 ±3.5 0.14 15 TO-99, Plastic H-8, N-8 100, 48 0 to 70
AD584T 2.5 ± 3.5 0.14 20 TO-99 H-8 100 –55 to +125
AD584S 2.5 ± 7.5 0.30 30 TO-99 H-8 100 –55 to +125
AD584J 2.5 ± 7.5 0.30 30 TO-99, Plastic H-8, N-8 100, 48 0 to 70

AD584L 5 ±3 0.06 5 TO-99 H-8 100 0 to 70
AD584K 5 ± 6 0.12 15 TO-99, Plastic H-8, N-8 100, 48 0 to 70
AD584T 5 ± 6 0.12 15 TO-99 H-8 100 –55 to +125
AD584S 5 ±15 0.30 30 TO-99 H-8 48 –55 to +125
AD584J 5 ± 15 0.30 30 TO-99, Plastic H-8, N-8 100, 48 0 to 70

AD584L 7.50 ±4 0.05 5 TO-99 H-8 100 0 to 70
AD584K 7.50 ± 8 0.11 15 TO-99, Plastic H-8, N-8 100, 48 0 to 70
AD584T 7.50 ±8 0.11 15 TO-99 H-8 100 –55 to +125
AD584S 7.50 ± 20 0.27 30 TO-99 H-8 100 –55 to +125
AD584J 7.50 ±20 0.27 30 TO-99, Plastic H-8, N-8 100, 48 0 to 70

AD584L 10.00 ±5 0.05 5 TO-99 H-8 100 0 to 70
AD584K 10.00 ± 10 0.10 15 TO-99, Plastic H-8, N-8 100, 48 0 to 70
AD584T 10.00 ± 10 0.10 15 TO-99 H-8 100 –55 to +125
AD584S 10.00 ± 30 0.30 30 TO-99 H-8 100 –55 to +125
AD584J 10.00 ±30 0.30 30 TO-99, Plastic H-8, N-8 100, 48 0 to 70

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD584 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.

–4–

WARNING!

ESD SENSITIVE DEVICE

REV. B