Analog Devices AD584 Datasheet

Pin Programmable

a

FEATURES
Four Programmable Output Voltages:

10.000 V, 7.500 V, 5.000 V, 2.500 V
Laser-Trimmed to High Accuracies
No External Components Required
Trimmed Temperature Coefficient:

5 ppm/8C max, 08C to +708C (AD584L)
15 ppm/8C max, –558C to +125°C (AD584T)

Zero Output Strobe Terminal Provided
Two Terminal Negative Reference

Capability (5 V & Above)
Output Sources or Sinks Current
Low Quiescent Current: 1.0 mA max
10 mA Current Output Capability
MIL-STD-883 Compliant Versions Available

GENERAL DESCRIPTION

The AD584 is an eight-terminal precision voltage reference of­fering pin-programmable selection of four popular output volt­ages: 10.000 V, 7.500 V, 5.000 V and 2.500 V. Other output
voltages, above, below or between the four standard outputs, are
available by the addition of external resistors. Input voltage may
vary between 4.5 and 30 volts.

Laser Wafer Trimming (LWT) is used to adjust the pin-pro­grammable output levels and temperature coefficients, resulting
in the most flexible high precision voltage reference available in
monolithic form.

In addition to the programmable output voltages, the AD584
offers a unique strobe terminal which permits the device to be
turned on or off. When the AD584 is used as a power supply
reference, the supply can be switched off with a single, low­power signal. In the “off” state the current drain by the AD584
is reduced to about 100 µA. In the “on” state the total supply
current is typically 750 µA including the output buffer amplifier.

The AD584 is recommended for use as a reference for 8-, 10- or
12-bit D/A converters which require an external precision refer­ence. The device is also ideal for all types of A/D converters of
up to 14-bit accuracy, either successive approximation or inte­grating designs, and in general can offer better performance
than that provided by standard self-contained references.

The AD584J, K and L are specified for operation from 0°C to
+70°C; the AD584S and T are specified for the –55°C to
+125°C range. All grades are packaged in a hermetically sealed
eight-terminal TO-99 metal can; the AD584 J and K are also
available in an 8-pin plastic DIP.

*Protected by U.S. Patent No. 3,887,863; RE 30,586

Precision Voltage Reference

AD584*

PIN CONFIGURATIONS

8-Pin TO-99

8-Pin DIP

PRODUCT HIGHLIGHTS

1. The flexibility of the AD584 eliminates the need to design­in and inventory several different voltage references. Fur­thermore one AD584 can serve as several references
simultaneously when buffered properly.

2. Laser trimming of both initial accuracy and temperature co­efficient results in very low errors over temperature without
the use of external components. The AD584LH has a maxi­mum deviation from 10.000 volts of ± 7.25 mV from 0°C to
+70°C.

3. The AD584 can be operated in a two-terminal “Zener”
mode at 5 volts output and above. By connecting the input
and the output, the AD584 can be used in this “Zener” con­figuration as a negative reference.

4. The output of the AD584 is configured to sink or source
currents. This means that small reverse currents can be tol­erated in circuits using the AD584 without damage to the
reference and without disturbing the output voltage (10 V,

7.5 V and 5 V outputs).

5. The AD584 is available in versions compliant with MIL­STD-883. Refer to the Analog Devices Military Products
Databook or current AD584/883B data sheet for detailed
specifications.

REV. A

Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] Fax: [phone]

AD584–SPECIFICATIONS

(@ VIN = +15 V and 258C)

Model AD584J AD584K AD584L

Min Typ Max Min Typ Max Min Typ Max Units

OUTPUT VOLTAGE TOLERANCE

Maximum Error

1

for Nominal

Outputs of:

10.000 V 630 610 65 mV

7.500 V 620 68 64 mV

5.000 V 615 66 63 mV

2.500 V 67.5 63.5 62.5 mV

OUTPUT VOLTAGE CHANGE

Maximum Deviation from +25°C

Value, T

MIN

to T

MAX

2

10.000 V, 7.500 V, 5.000 V Outputs 30 15 5 ppm/°C

2.500 V Output 30 15 10 ppm/°C

Differential Temperature

Coefficients Between Outputs 5 3 3 ppm/°C

QUIESCENT CURRENT 0.75 1.0 0.75 1.0 0.75 1.0 mA

Temperature Variation 1.5 1.5 1.5 µA/°C

TURN-ON SETTLING TIME TO 0.1% 200 200 200 µs
NOISE

(0.1 Hz to 10 Hz) 50 50 50 µV p-p

LONG-TERM STABILITY 25 25 25 ppm/1000 Hrs
SHORT-CIRCUIT CURRENT 30 30 30 mA
LINE REGULATION (No Load)

15 V ≤ V
(V

OUT

≤ 30 V 0.002 0.002 0.002 %/V

IN

+2.5 V) ≤ VIN ≤ 15 V 0.005 0.005 0.005 %/V

LOAD REGULATION

0 ≤ I

≤ 5 mA, All Outputs 20 50 20 50 20 50 ppm/mA

OUT

OUTPUT CURRENT

≥ V

V

IN

OUT

+2.5 V

Source @ +25°C 101010mA
Source T
Sink T

MIN

MIN

to T

to T

MAX

MAX

555mA
555mA

TEMPERATURE RANGE

Operating 0 +70 0 +70 0 +70 °C
Storage –65 +175 –65 +175 –65 +175 °C

PACKAGE OPTION

3

TO-99 (H-08A) AD584JH AD584KH AD584LH
Plastic (N-8) AD584JN AD584KN

NOTES

1

At Pin 1.

2

Calculated as average over the operating temperature range.

3

H = Hermetic Metal Can; N = Plastic DIP.
Specifications subject to change without notice.
Specifications shown in boldface are tested on all production units at final electrical
test. Results from those tests are used to calculate outgoing quality levels. All min
and max specifications are guaranteed, although only those shown in boldface are
tested on all production units.

METALIZATION PHOTOGRAPH

Dimensions shown in inches and (mm).

ABSOLUTE MAXIMUM RATINGS

Input Voltage VIN to Ground . . . . . . . . . . . . . . . . . . . . . . . 40 V

Power Dissipation

@ +25°C . . . . . . . . . . . . . . . . . . . . 600 mW

Operating Junction Temperature Range . . . .–55°C to +125°C

Lead Temperature (Soldering 10 sec) . . . . . . . . . . . . . +300°C

Thermal Resistance

Junction-to-Ambient (H-08A) . . . . . . . . . . . . . . . . 150°C/W

–2–

REV. A

Model AD584S AD584T

Min Typ Max Min Typ Max Units

AD584

OUTPUT VOLTAGE TOLERANCE

Maximum Error

1

for Nominal

Outputs of:

10.000 V 630 610 mV

7.500 V 620 68 mV

5.000 V 615

±

6 mV

2.500 V 67.5 63.5 mV

OUTPUT VOLTAGE CHANGE

Maximum Deviation from +25°C

Value, T

MIN

to T

MAX

2

10.000 V, 7.500 V, 5.000 V Outputs 30 15 ppm/°C

2.500 V Output 30 20 ppm/°C

Differential Temperature

Coefficients Between Outputs 5 3 ppm/°C

QUIESCENT CURRENT 0.75 1.0 0.75 1.0 mA

Temperature Variation 1.5 1.5 µA/°C

TURN-ON SETTLING TIME TO 0.1% 200 200 µs
NOISE

(0.1 Hz to 10 Hz) 50 50 µV p-p

LONG-TERM STABILITY 25 25 ppm/1000 Hrs
SHORT-CIRCUIT CURRENT 30 30 mA
LINE REGULATION (No Load)

15 V ≤ V
(V

OUT

≤ 30 V 0.002 0.002 %/V

IN

+2.5 V) ≤ VIN ≤ 15 V 0.005 0.005 %/V

LOAD REGULATION

0 ≤ I

≤ 5 mA, All Outputs 20 50 20 50 ppm/mA

OUT

OUTPUT CURRENT

V

IN

≥ V

OUT

+2.5 V

Source @ +25°C1010mA
Source T
Sink T

MIN

MIN

to T

to T

MAX

MAX

55mA
55mA

TEMPERATURE RANGE

Operating –55 +125 –55 +125 °C
Storage –65 +175 –65 +175 °C

PACKAGE OPTION

TO-99 (H-08A) AD584SH AD584TH

NOTES

1

At Pin 1.

2

Calculated as average over the operating temperature range.
Specifications subject to change without notice.
Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All min
and max specifications are guaranteed, although only those shown in boldface are tested on all production units.

REV. A

–3–