Amprobe ACD-10-PLUS, ACD-10-TRMS-PLUS Specifications

Download

Page 1

No hassle

600V

warranty

No waiting.

No shipping charges.

Our commitment to high-quality products and customer service is demonstrated by our industry exclusive “No Hassle” warranty. In the unlikely event that an Amprobe Test Tool requires warranty service, any of our local dealers are authorized to replace it, on the spot.

Data Sheet

ACD-10 PLUS

600A Clamp-On Multimeter

Amprobe’s ACD-10 PLUS meter offers thinner jaws over standard clamp meters. Allowing access to tight measurement areas and still accommodating conductors up to 25 mm. It also measures Capacitance and Frequency. Frequency is measured by either jaws or test leads. Very versatile clamp multimeter.

AC & DC Voltage to 600V ■ AC Current to 600A ■ Thin Jaws, only 10mm (0.4”) thick ■ Resistance to 40M ■ W Continuity Buzzer

■

Capacitance to 3000 uF ■ Frequency measurement ■ In rush current ■ Hold & Maximum reading functions ■ Accommodates conductors up to 26mm (1.02”) in diameter ■ Auto ranging ■ Auto power off ■ Rubber over-molded case ■ Overload protected ■

(note: $500 MSLP limit)

Amprobe® Test Tools

www.Amprobe.com

Page 2

ACD-10 PLUS 600A Clamp-On Multimeter

Data Sheet

General Specifications

Display: 3-3/4 digits 4000 counts LCD display Update Rate: 3 per second nominal Polarity: Automatic Operating Temperature: 0 °C to 40 °C; < 80% RH for temperature up to 31 °C decreasing linearly to 50% RH at 40 °C Altitude: Operating below 2000m; Indoor use Storage Temperature: -20 °C to 60 °C, < 80% RH (with battery removed) Temperature Coefﬁcient: nominal 0.15 x (speciﬁed accuracy)/°C @ (0 °C ~ 18 °C or 28 °C ~ 40 °C) Low Battery: Below approx. 2.4V Power Supply: 3V coin battery IEC-CR2032 Power Consumption: 2.8 mA typical except that 3.3 mA typical for ACA function APO Timing: Idle for 30 minutes APO Consumption: 5 μA typical Dimension: 190 x 63 x 32 mm (7.4 x 2.5 x 1.3 in) Weight: 139 gm approx Jaw opening & Conductor diameter: max 26 mm Special Features : 30ms Max Hold; Data Hold; Relative Zero mode Safety: Meets EN61010-2-032, UL61010B-2-032, IEC61010-1 2nd Ed., EN61010-1

2nd Ed., UL61010-1 2nd Ed. CAT III-600 Volts ac & dc; Pollution degree : 2 EMC: Conforms to EN61326-1. This product complies with requirements of the following European Community Directives: 89 / 336/ EEC (Electromagnetic Compatibility)

and 73/ 23/ EEC (Low Voltage) as amended by 93/ 68/ EEC (CE Marking). However, electrical noise or intense electromagnetic ﬁelds in the vicinity of the equipment may disturb the measurement circuit. Measuring instruments will also respond to unwanted signals that may be present within the measurement circuit. Users should exercise care and take appropriate precautions to avoid misleading results when making measurements in the presence of electronic interference.

Electrical Speciﬁcation Accuracy (23 °C ± 5 °C & < 75% R.H.)

Function Range Accuracy

DC Voltage

400.0 mV ±( 0.3% + 4 digits)

4.000, 40.00, 400.0 V ±( 0.5% + 3 digits) 600 V ±( 1.0% + 4 digits) NMRR: >50 dB @ 50/60Hz CMRR: >120 dB @ DC, 50/60 Hz, Rs =1 kW Input Impedance: 10 MW, 30 pF nominal (1000 MW for 400.0 mV range) Transient protection: 6.5 kV (1.2/50 μs surge)

AC Voltage (50Hz ~ 500Hz)

4.000, 40.00, 400.0 V ±( 1.5% + 5 digits) 600 V ±( 2.0% + 5 digits) CMRR: >60dB @ DC to 60 Hz, Rs=1 kW Maximum Crest Factor: < 1.75 : 1 at full scale & < 3.5 : 1 at half scale limited to

fundamental and harmonics, that fall within the meter speciﬁed AC bandwidth for non-sinusoidal waveforms

Input Impedance: 10 MW, 30 pF nominal Transient protection: 6.5 kV (1.2/50μs surge) ACD-10 Plus: Average Sensing

Amprobe® Test Tools

www.Amprobe.com

Page 3

ACD-10 PLUS 600A Clamp-On Multimeter

Electrical Speciﬁcation Accuracy (23 °C ± 5 °C & < 75% R.H.), cont.

Function Range Accuracy

Data Sheet

AC Current (Clamp-on 50Hz / 60Hz) Range Accuracy

40.00, 400.0, 600 A ±( 1.5% + 8 digits) Overload Protections: ACA Clamp-on jaws : 600 A rms continuous ACD-10 Plus: Average Sensing

Max Induced error from adjacent current carrying conductor: 0.05 A

Speciﬁed accuracy is from 1% to 100% of range and for measurements made at the jaw center. When the conductor is not positioned at the jaw center, position errors introduced are: Add 2% to speciﬁed accuracy for measurements made BEYOND jaw marking lines (toward jaw opening)

Add 8 digits to speciﬁed accuracy @ reading < 10% of range

Resistance

400.0 W ±( 0.8% + 8 digits)

4.000, 40.00, 400.0 kW ±( 0.6% + 4 digits)

4.000 MW ±( 1.0% + 4 digits)

40.00 MW ±( 2.0% + 4 digits) Open Circuit Voltage : 0.4 VDC typical Transient protection : 6.5 kV (1.2/50μs surge)

Frequency

Function Sensitivity (Sine RMS) Range Accuracy

400.0 mVac 350mV 1 0 Hz ~ 2 kHz ±( 0.5%+4 digits)

4.000 Vac 1V 5 Hz ~ 5 kHz ±( 0.5%+4 digits)

4.000, 40.00 Vac 32V 5 Hz ~ 100 kHz ±( 0.5%+4 digits)

400.0 Vac 90V 5 Hz ~ 10 kHz ±( 0.5%+4 digits) 600 Vac 500V 5 Hz ~ 5 kHz ±( 0.5%+4 digits)

400.0 Aac 60A 40 Hz ~ 400 Hz ±( 0.5%+4 digits) Display counts: 5000 Resolution: 0.001Hz Overload Protection : ACA Clamp-on jaws : AC 600A rms continuous Transient protection : VAC input jacks : 6.5kV (1.2/ 50μs surge)

Capacitance

Range

500.0nF, 5.000μF, ±( 3.5% + 6 digits)

50.00μF, 500.0μF, 3000μF

1) Additional 50.00nF range accuracy is not speciﬁed

2) Accuracies with ﬁlm capacitor or better

3) Speciﬁed with battery voltage above 2.8V (approximately half full battery). Accuracy decreases gradually to 12% at low battery warning voltage of approximately 2.4V

Transient protection: 6.5 kV (1.2/50 μs surge) Audible Continuity Tester Audible indication : between 10 W and 120 W. Transient protection: 6.5 kV (1.2/50 μs surge) Diode Tester / Open Circuit Voltage Test Current

(Typical) < 1.6 VDC @ 0.25 mA Transient protection: 6.5 kV (1.2/50 μs surge)

Max Hold* (where applicable)

Speciﬁed accuracy ± 50 digits for changes > 25 ms in duration

Accuracy

1) 2) 3)

2) 3)

www.Amprobe.com

Page 4

ACD-10 PLUS 600A Clamp-On Multimeter

Included Accessories

Test leads, battery installed, soft carrying pouch, and users manual

Data Sheet

Amprobe® Test Tools

website: www.Amprobe.com email: info@amprobe.com Everett, WA 98203 Tel: 877-AMPROBE

Amprobe® Test Tools Europe

In den Engematten 14 79286 Glottertal, Germany Tel.: +49 (0) 7684 8009 - 0

Amprobe® Test Tools

www.Amprobe.comwww.Amprobe.com