SVT-410HLF
Bass Guitar Cabinet
Owner’s Manual
SVT-410HLF Bass Guitar Cabinet
TABLE OF CONTENTS
What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Jackplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Suggested Hookup Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Technical Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Warranty and Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
What’s in the Box
SVT®-410HLF Bass Guitar Cabinet, Quick Start Guide.
Introduction
Your Ampeg SVT-410HLF 4x10 Bass Guitar Cabinet is a high quality, two-way speaker
cabinet, suitable for all sizes of venues. The cabinet features heavy duty recessed handles,
an industrial strength grip bar, and heavy duty rear wheels. Skid rails are placed on the
back of the enclosure to protect it while loading in and out of venues.
The Speakon® and 1/4" jacks are wired in parallel, allowing easy daisy chaining from
one speaker cabinet to another. Each of the jacks may be used as an input or a through
connection. Speakon connectors are recognized as the standard for professional
installations, assuring a secure, permanent connection that won’t corrode, vibrate loose or
be easily tampered with. The 1/4" jacks are convenient, however, the Speakon jacks are
recommended when using power ampliers over 150 watts for permanent installations, or
for the “rst” speaker among a number of daisy chained speakers.
In order to get the most out of your new Ampeg speaker cabinet, please fully read this
Owner’s Manual, as well as the Important Safety Instructions included with your cabinet,
before you begin playing.
And thank you for choosing Ampeg.
2
Jackplate
1-
1+
1 2 3
1. 1/4" Input / Output Jacks
2. Speakon Input / Output Jacks
3. High Frequency Horn Level Control
SVT-410HLF Bass Guitar Cabinet
4
5
6
7
8
9
10
11
12
16
8
-db
LEVEL CONTROL
3
2
1
0
Speakon to 1/4" Wiring Diagram
1+
1-
3
Suggested Hookup Diagrams
-db
LEVEL CONTROL
4
5
6
7
8
8
9
10
11
12
16
0
1
2
3
-db
LEVEL CONTROL
4
5
6
7
8
8
9
10
11
12
16
0
1
2
3
1
SVT-410HLF Bass Guitar Cabinet
In example 1 above, a speaker cable with 1/4" ends connects from one speaker output of
the amplier to the speaker input of the Ampeg SVT-410HLF cabinet. An additional cabinet
may be connected by attaching another speaker cable from the remaining 1/4" speaker
output of the amplier to a speaker input of the next cabinet.
WARNING: Always use good quality (non-shielded) speaker cables. Never use
(shielded) instrument cables to connect speakers to an amplier.
4
SVT-410HLF Bass Guitar Cabinet
PIN 1+ = POS(+)
PIN 1- = NEG(-)
-db
LEVEL CONTROL
4
5
6
7
8
8
9
10
11
12
16
0
1
2
3
-db
LEVEL CONTROL
4
5
6
7
8
8
9
10
11
12
16
0
1
2
3
-db
LEVEL CONTROL
4
5
6
7
8
8
9
10
11
12
16
0
1
2
3
-db
LEVEL CONTROL
4
5
6
7
8
8
9
10
11
12
16
0
1
2
3
2
Example 2 above is not as common, but is great for daisy-chaining multiple cabinets. You
may connect a speaker cable with 1/4" or Speakon ends from one speaker output of the
amplier to the speaker input of the Ampeg SVT-410HLF cabinet. An additional cabinet
may be connected by attaching another speaker cable from an open jack (thru) to the input
jack of the next cabinet. Multiple cabinets may be daisy-chained this way.
WARNING: Always use good quality (non-shielded) speaker cables. Never use
(shielded) instrument cables to connect speakers to an amplier. Also, do not use
both cable routes listed in example 2 above. Use one route or the other, but never both
simultaneously!
5
SVT-410HLF Bass Guitar Cabinet
Technical Specications
Type 4x10 Bass Enclosure
Frequency Response (+/–3 dB) 48 Hz – 18 kHz
Usable Low Frequency (–10 dB) 28 Hz
RMS Power Handling 500 Watts RMS
Peak Power Handling 1000 Watts
Impedance 4 Ω
Sensitivity 98 dB SPL 1W/1m
Maximum SPL 125 dB
Components 4 Custom Designed, 100 Watt, 10” speakers
1 High Frequency Horn
Size (H x W x D) 24.0 in (with feet) x 30.0 in x 19.0 in
610 mm (with feet) x 762 mm x 483 mm
Weight (approximate) 110 lb
49.90 kg
The SVT-410HLF is covered with a durable, fabric-backed vinyl material. Clean with a dry, lint-free cloth. Never spray
cleaning agents on the SVT-410HLF. Avoid abrasive cleansers which would damage the finish.
Ampeg continually develops new products and improves upon existing ones. For this reason, the specifications and
information in this manual are subject to change without notice.
CAUTION: THIS SPEAKER IS CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED
EXPOSURE TO HIGH SOUND PRESSURE LEVELS CAN CAUSE PERMANENT HEARING IMPAIRMENT OR LOSS.
USER CAUTION IS ADVISED, AND EAR PROTECTION RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME.
6
SVT-410HLF Bass Guitar Cabinet
Warranty and Support
Visit WWW.AMPEG.COM to...
(1) ...identify WARRANTY coverage provided in your local market. Please keep your
sales receipt in a safe place.
(2) ...REGISTER your product.
(3) ...CONTACT Technical Support, or call 818-575-3600.
www.ampeg.com
26580 Agoura Road, Calabasas, CA 91302-1921 USA
© 2019 Yamaha Guitar Group, Inc. All rights reserved.
Ampeg, the Ampeg logo, and SVT are trademarks or registered trademarks of Yamaha Guitar Group, Inc. in the U.S.
and/or other jurisdictions. Speakon is a registered trademark of Neutrik AG Corporation.
Yamaha Guitar Group, Inc.
Rev. A
7
Loading...