AMETEK FPDC User Manual
Technical Note
ReFlex Power™ Mating Connectors for FPDC Module
Document No. W380274-01 Rev E • 1/23/2009
PURPOSE
Provide mating connector information for the ReFlex Power™ Fixed Power D C (FPDC) mod ule.
Figure 1. FPDC Front Panel View
MATING CONNECTOR KIT
FPDC Mating Connector Kit - AMETEK Part No. 5380274-01, mates with RFP-F1000-001-XXXX, and includes the following for
both Interface and DC output connectors:
Bill of Material
AMETEK
Item
Part No.
1 856-214-04
2 856-745-52 Contact, 12AWG, 30A, Male 4 MC4012D Positronic Industries
3 856-247-39 Conn, Backshell, 37P, Strt, 2 PC 1 D37000Z00 Positronic Industries
4 856-214-09
5 856-247-10
Description Qty
Conn, 21P, DSUB, 8/20AWG,
Male
Conn, 9P, DSUB, 20-24AWG,
Crimp, Male
Conn, Backshell, 9P, DSUB, 2
PC
Manufacturer Part
No.
1 CBC21WA4M1000Z Positronic Industries
1 SD9M1000Z Positronic Industries
1 D9000Z00 Positronic Industries
Manufacturer Suggested Source(s)
Positronic Ind.
http://www.connectpositronic.com/default.cfm
Positronic Ind.
http://www.connectpositronic.com/default.cfm
Positronic Ind.
http://www.connectpositronic.com/default.cfm
Positronic Ind.
http://www.connectpositronic.com/default.cfm
Positronic Ind.
http://www.connectpositronic.com/default.cfm
RECOMMENDED TOOLS (NOT INCLUDED WITH MATING CONNECTOR KIT)
Hand crimp: Positronic Industries P/N 95 07-0-0-0
Pneumatic crimp: Positronic Industries P/N 9550-1-0
Insertion/extraction: Positronic Industries P /N M81969/1-02
Pins A1 – A3 insertion/extraction: Positronic Industries P/N 4711-2-0-0
Pin A4 extraction: Positronic Industries P/N 4311-0-0-0
9250 Brown Deer Road, Sa n Diego CA 92121 • Tel: 858-4 50-008 5 • Fax: 858-458- 0267 • e mail: sal es@progra mmablep ower.com • Web: www.programm ablepow er.com
©2008 AMETEK Programmable Pow er, Inc. • All rights reserv ed. • AME TEK is a tr ademark o f AMETEK, Inc .
1 of 4
Technical Note
ReFlex Power™ Mating Connectors for FPDC Module
Document No. W380274-01 Rev E • 1/23/2009
INTERFACE CONNECTOR
Connector: Positronic Industries P/N SD9M1000Z, AMETEK P/N 856-214-09
Crimp Contacts: Positronic Industries P/N MC75 20D (initially suppli ed with conne ctor)
Backshell: Positronic Industries P/N D9000Z00, AMETEK P/N 856-247-10
Wire size: Maximum gauge 20 AWG (22 AWG recommended)
Maximum length 10 meters.
INTERFACE PINOUT
Figure 2. Interface Connector, Front Panel View, and Interface Connector Wiring Diagram
Pin Signal Description
1 ENAB1 Enable module output
2 Reserved
3 Reserved
4 Reserved
5 CHAS GND Chassis Ground
6 ENAB RTN1 Enable module output return
7 Reserved
8 Reserved
9 Reserved
1
Enable signal is internally pulled up to +5V with a 10 K resistor. To enable the module, the
signal is pulled low (<= 0.5V) with respect to the ENA RTN signal; this may also be
accomplished by shorting Pin 1 to Pin 6.
OPTIONAL INTERFACE CONNECTOR ACCESSORIES
• AMETEK P/N 5380508-01, 9-pin Loop-back Connector Assembly, includes a jumper wire between Pins 1 and 6 to
enable the module outputs.
• AMETEK P/N 5380448-01, Power Module, 9ft. Unterminated Interface Cable Assembly. Use when interfacing to an
external system.
• AMETEK P/N 5380448-03, Power Module, Right Angle, 9ft. Unterminated Interface Cable Assembly. Use when
interfacing to an external system.
9250 Brown Deer Road, Sa n Diego CA 92121 • Tel: 858-4 50-008 5 • Fax: 858-458- 0267 • e mail: sal es@progra mmablep ower.com • Web: www.programm ablepow er.com
©2008 AMETEK Programmable Pow er, Inc. • All rights reserv ed. • AME TEK is a tr ademark o f AMETEK, Inc .
2 of 4
Loading...