Installation
Instructions
T M
2808.222
2908.222
Widespread Lavatory Faucet with the
Speed Connect™ Drain
Congratulations on purchasing your American Standard faucet with the Speed Connect Drain, a feature found only on
American Standard faucets.
Speed Connect Drain*
•1/3 of the parts, installs in 1/3 of the time
•No tools needed
•Never needs adjustment
•Guaranteed to seal properly the first time, every time.
Certified to comply with ANSI A112.18.1
US60385 Rev. 1 . 2
*Your new American Standard faucet is designed to work only with the Speed Connect drain. Helpful tips for removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended tools |
|
|
|
Screwdriver |
Channel Locks |
Adjustable Wrench |
Tubing Cutter |
1 |
|
INSTALL SPOUT |
CAUTION |
Turn off water at |
|
|
|
|
|
|
|
|
main supply. |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|||
|
|
Insert SPOUT (1) and CABLE CONNECTOR (2) through center hole, making sure |
Fig. A. |
|||||||
|
|
|||||||||
|
|
the SEAL WASHER (3) is properly seated in SPOUT (1). |
|
|
|
|
|
|||
|
|
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT |
||||||||
|
|
|||||||||
|
|
SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting |
|
|
|
|||||
|
|
hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink. |
|
|
|
|
1 |
|||
|
|
|
|
|
Tighten LOCKNUT (6) firmly. Fig. A.
3
7
1A INSTALL VALVE BODY
Place RUBBER RING (9) into ESCUTCHEON (10).
Install LOCKNUT (11) onto VALVE BODY (12). |
|
4 |
|
|
|
||
From under side of mounting surface, install VALVE BODY (12) through valve |
SLOT |
5 |
|
mounting holes. Threads of VALVE BODY (12) should extent at least 5/16 |
|||
|
|
||
of a inch above mounting surface top. Fig. B. |
|
6 |
|
Important: Thread ESCUTCHEON (10) onto VALVE BODY (12) until snug against |
|
||
|
|
||
internal stop. This is key to the installation. If not done, the faucet handles won’t |
|
2 |
|
work correctly. If necessary, adjust LOCKNUT (11). |
|
Hand tighten LOCKNUT (11) to secure VALVE BODY (12).
Repeat above steps for opposite VALVE BODY (12A).
10 |
|
|
|
9 |
10 |
1 |
|
5/16'' MIN. |
9 |
||
|
|||
MOUNTING |
|
||
|
12a |
||
SURFACE |
|
Fig. B. |
11 |
12 |
|
12 |
|||
|
11 |
||
|
|
2808 SERIES
1
2 INSTALL POP-UP DRAIN
Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). Fig. A.
Drop DRAIN BODY (4) through sink drain hole. Make sure WHITE FOAM GASKET (5) is under flange of DRAIN BODY (4). Fig. B.
Note: No plumber’s putty or caulk is required.
The CABLE ATTACHMENT POINT (6) must face towards the rear of the SINK. Fig. B.
Fig. A. |
Fig. B. |
REAR OF |
|
|
SINK |
1 |
|
|
3 |
|
4 |
|
|
6 |
|
|
5 |
2 |
|
SINK |
|
DRAIN |
|
|
|
HOLE |
3 INSTALL BLACK GASKET
Install BLACK CONE GASKET (1) onto DRAIN BODY (2) from below.
Note: The flat side of the BLACK CONE GASKET (1) must face down.
2
1
FLAT SIDE OF GASKET MUST FACE DOWN
4 |
INSTALL GRAY LOCKNUT |
Fig. A. |
|
Fig. B. |
|
Install GRAY LOCKNUT (1) onto DRAIN |
|
|
|
|
BODY (2) from below SINK. Fig. A. |
|
|
|
|
Note: The flat side of the GRAY LOCKNUT (1) |
|
|
|
|
must face up. |
|
2 |
|
|
Tighten firmly by hand. No tools are required. |
|
|
DRAIN |
|
Check DRAIN FLANGE in SINK to ensure that |
|
|
FLANGE |
|
WHITE FOAM GASKET (3) is fully compressed |
|
|
FLAT SIDE OF |
|
and not visible. Fig. B. |
|
|
GRAY LOCKNUT |
|
|
|
MUST FACE UP |
|
|
|
|
1 |
3 WHITE FOAM |
|
|
|
|
|
|
|
|
|
GASKET |
|
|
|
|
NOT VISIBLE |
5 |
POP-UP KNOB |
|
|
DOWN |
|
POP-UP KNOB (1) must be fully down. |
|
|
|
|
|
|
|
1 |
US60385 Rev. 1 . 2
2