American Standard SILHOUETTE 25 User Manual

SILHOUETTE™ 25" SINGLE BOWL KITCHEN SINK

• Americast® brand engineered material

• Single bowl design

• Titanium enamel - heat resistant up to 1000°

• Acid-resisting glossy porcelain nish

• Tile edge installation

• Silicone sealant supplied

• Available in 1, 3 or 4 faucet hole conguration

• Customized hole punchings available (see page G56)

Tile Edge:

❏ 7172.011 Center hole only ❏ 7172.813 3 hole ❏ 7172.814 4 hole

Nominal Dimensions:

635 x 559 x 241mm (25" x 22" x 9-1/2")

SILHOUETTE™ 25"

SINGLE BOWL SINK

AMERICAST

Bowl sizes:

552mm (21-3/4") wide 476mm (18-3/4") front to back 229mm (9") deep

Compliance Certications Meets or Exceeds the Following Specications:

• ASME A112.19.4M for Americast Plumbing Fixtures

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS

To Be Specied:

❏ Color: ❏ Faucet*: ❏ Faucet Finish: ❏ Basket Strainer: 4331.013 ❏ Soap Dispenser: 4503.115, Color: ❏ Trap:

Optional Accessories:

❏ Large Wood Cutting Board: 9000.250 ❏ Small Wood Cutting Board: 9000.185 ❏ Colander for Cutting Board: 8102.100, Color: ❏ Large Colander: 8103.100, Color: ❏ Bottom Sink Rack: 7404.100, Color:

* See faucet section for available models

G35

Revised 2/08

7172.813/814

FIN IS HE D WALL OR SP LA SH BACK

*C UT OU T NOTE

7 17 2. 81 4 4 H OL E

C/L

SEA LI NG COM PO UN D

FIN IS HE D FLO OR

TIL ED

COU NT ER TO P

(BY O TH ER S)

9-1 /8 "

(23 2m m)

1-1 /2 " O .D . TAILP IE CE

36" (9 14 mm )

SUG GE ST ED

5-3 /4 "

(14 6m m)

2" ( 51 mm )

OPT IO NA L

7-7 /8 "

(20 0m m)

3-1 /2 " (89 mm ) DIA .

22"

(55 9m m)

3/8 "

(10 mm )

12- 1/ 2"

(31 8m m)

25"

(63 5m m)

3/4 "

(19 mm )

5-7 /8 "

(14 9m m)

2-1 /8 " (54 mm )

1-1 /2 " ( 38 mm) DIA . HO LE S TYP.

3" (76 mm )

4"(1 02 mm )

(10 2m m)

SILHOUETTE™ 25"

SINGLE BOWL SINK

AMERICAST

NOTES:

COUNTERTOP CUTOUT 603mm x 527mm WITH 25mm RADIUS

(23-3/4 X 20 -3/4 WITH 1” RADIUS) AT CORNERS.

■ ON FOUR HOLE VERSIONS, SPACING BETWEEN FAR RIGHT HOLES IS 3".

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP SUPPORTS.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ASME Standard A112.19.4 These measurements are subject to c hange or cancellation. No responsibility is assumed for use of superseded or voided leaet.

G36

Revised 2/08