American Standard Renaissance 2241, Compact 2149.012, 3505, Two-Piece Toilets with Aquameter, Compact 3505 User Manual
...
INSTALLATION INSTRUCTIONS
For Two-Piece Toilets with Aquameter™ Fill Valve
RENAISSANCE 2241
COMPACT 2149.012, 3505
COLONY 2388 / 2399 / 2359
COLONY AFTON 2329.016
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations may
require professional help.) Also be sure your installation conforms to local codes
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY
HANDLE WITH CARE!
NOTE:
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure
Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level
Pictures may not exactly define contour of china and components.
1 REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE:
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
Mounting surface must be clean and level before new toilet is installed!
ROUGHING-IN DIMENSIONS:
NOTE:
be as listed below:
For 4010.010/4310.016 Tanks: A = 254mm (10")
For 4014/4314 Tanks: A = 356mm (14")
For 4010.012/4392.016 and all other Tanks: A = 305mm (12")
Distance from wall to closet flange centerline must
FINISHED WALL
SUPPLY
AS
REQ'D.
If replacing valve, first shut off main water supply!
32
CLOSET FLANGE
A
CLOSET BOLTS
SAVE FOR FUTURE USE
A
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2004
FINISHED
FLOOR
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90°,
and slide into place 6" (152 mm) apart and
parallel to wall.
Saniwares
730237-100 REV. Q
SEALANT
WAX RING
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent
damage), and install wax ring evenly around
waste flange (horn), with tapered end of ring
facing toilet. Apply a thin bead of sealant
around base flange.
54
NUT
TAPERED
WASHER
CLOSET
BOLT
FLANGE
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange
so bolts project through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers
marked "THIS SIDE UP"
must
face up!
6
BOLT CAP
CLOSET FLANGE
CLOSET BOLT
WASHER
NUT
INSTALL TOILET
a. Position toilet squarely to wall and, with a
rocking motion, press bowl down fully on wax
ring and flange. Alternately tighten nuts until
toilet is firmly seated on floor.
!
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b. Install caps on washers. (If necessary, cut
bolt height to size before installing caps.)
c. Smooth off the bead of sealant around
base. Remove excess sealant.
For Tanks/Bowls using Speed
7a
Connect System (Tank
mounting bolts pre-installed).
TANK MTG.
BOLTS PREINSTALLED
WASHER
NUT
RUBBER
GASKET
INSTALL TANK
a. Install large rubber gasket
over threaded outlet on bottom
of tank and lower tank onto bowl
so that tapered end of gasket fits
evenly into bowl water inlet
opening, and tank mounting
bolts go through mounting holes.
Secure with metal washers and
nuts.
b. With tank parallel to wall,
alternately tighten nuts until tank
is snugged down evenly against
bowl surface.
!
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
CAUTION:
For all other Tanks/Bowls
7b
RUBBER
WASHER
TANK MTG.
BOLTS
WASHER
NUT
RUBBER
GASKET
INSTALL TANK
a. Install large rubber gasket
over threaded outlet on bottom
of tank and lower tank onto bowl
so that tapered end of gasket fits
evenly into bowl water inlet
opening.
b. Insert tank mounting bolts
and rubber washers from inside
tank, through mounting holes,
and secure with metal washers
and nuts.
c. With tank parallel to wall,
alternately tighten nuts until tank
is snugged down evenly against
bowl surface.
!
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
CAUTION:
8
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
- 2 -
730237-100 REV. Q
9
WATER INLET
WASHER
COUPLING NUT
TANK
FLEXIBLE
SUPPLY
VALVE NUT
10
TO RAISE
WATER
LEVEL
TO LOWER
WATER
LEVEL
TRIP
LEVER
WATER CONTROL
ASSEMBLY
FLOW RATE
ADJUSTMENT
LIFT
ROD
FLOAT
BALL
FIG. 10A
+
-
C L
REFILL
TUBE
OVERFLOW
TUBE
COMPRESSION
COLLAR
TRIM PLATE
VALVE
CAUTION: Overtightening of
COUPLING NUT could result in
breakage and potential flooding.
ADJUSTMENTS
a. Flush tank and check that tank fills and shuts off within 30 to 60
b. To adjust water level: turn water level adjustment screw
CONNECT WATER SUPPLY
a. Connect water supply line between
shutoff valve and tank water inlet
fitting. Tighten COUPLING NUT 1/4 turn
beyond hand tight. Check that refill tube
is inserted into overflow tube.
b. Turn on supply valve and allow tank to
fill until float rises to shutoff position.
c. Check for leakage at fittings, tighten or
correct as needed.
d. Do not use plumber's putty to seal
these fittings.
REPAIR PARTS LIST
c. To adjust flow rate (tank fill time): turn flow rate adjustment screw
d. Carefully position tank cover on tank.
e. The flush valve float has been factory set and does not require
f. If bowl fails to siphon, an adjustment may be required with the lift chain.
Repair parts are determined by toilet tank number which can be
found marked inside tank.
NOTE: "XXX" represents color or trim finish options. Specify
when ordering.
PART NO.
047242-XXX0A
047148-XXX0A
047192-XXX0A
738172-XXX0A
738170-XXX0A
738171-XXX0A
034783-XXX0A
738145-0070A
738372-0070A
738351-0070A
738462-0070A
738138-0070A
738356-0070A
047188-0070A
047158-0070A
738159-0070A
738165-0070A
TRIP LEVER
TRIP LEVER
TRIP LEVER
RIGHT HAND TRIP LEVER
RIGHT HAND TRIP LEVER
RIGHT HAND TRIP LEVER
BOLT CAP KIT (INCL 2 COVERS & WASHERS)
WATER CONTROL ASS'y W FLOAT BALL
WATER CONTROL ASS'y W FLOAT BALL
WATER CONTROL ASS'y W FLOAT BALL
WATER CONTROL ASS'y W FLOAT BALL
FLUSH VALVE
FLUSH VALVE
COUPLING KIT, BOWL-TO-TANK
COUPLING KIT, BOWL-TO-TANK
FLAPPER ASSEMBLY
FLAPPER ASSEMBLY
DESCRIPTION
WATER LINE
LEVEL
WATER INLET
FLUSH VALVE
FLUSH
VALVE
FLOAT
FLAPPER
ASSEMBLY
seconds, and tank water level is set as specified on tank rear wall.
counterclockwise to raise level; turn adjustment screw clockwise to
lower level.
clockwise to decrease flow rate (increase fill time); turn adjustment
screw counterclockwise to increase flow rate (decrease fill time).
adjustments. Repositioning of the float will change the amount of
water used which may effect the toilet's performance.
Simply remove the bead chain from the retainment clip (see Fig. 10A)
and take up slack on the chain, and reinsert on lift rod. Make sure the
chain is not too taught.
TANK NUMBER
4010
COMPACT
4092
COLONY
4037
COLONY/
4310/4314/4392
RENAISSANCE
COLONY AFTON
✔
✔
✔
✔
✔
✔
✔✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
CARE AND CLEANING
11
When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents,
disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some
bathroom chemicals and cosmetics may damage the seat's finish.
WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This
!
damage can cause leakage and property damage. American Standard shall not be responsible or liable for any tank fitting damage
caused by the use of cleaners containing chlorine (calcium hypochlorite).
- 3 -
730237-100 REV. Q
TROUBLESHOOTING GUIDE
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Does not flush a. Water supply valve closed. a. Open valve and allow water to fill tank.
Poor or a. Tank water level too low. a. Follow instructions to adjust water level.
sluggish flush b. Bowl water level too low. b. Check that refill tube is connected to water control and
e. Partially clogged trapway and/or e. Remove obstruction. Consult a plumber if necessary.
b. Supply line blocked. b. Shut off water supply, disconnect supply line, and inspect
all gaskets and washers. Reassemble.
c. Flush valve chain too loose or c. Readjust chain length as required.
disconnected.
d. Stuck float/float rod. d. Adjust to allow free downward movement of float arm.
e. Water control flow rate too e. Follow instructions to increase water control flow rate.
restricted.
inserted into tank overflow without being kinked or damaged.
c. Supply valve partly closed. c. Open supply valve fully. Be sure that proper supply tube
size is used.
d. Flush valve closes early due to high d. Follow instructions to reduce water control flow rate.
supply pressure.
drain pipe and/or vent.
f. Supply pressure too low. f. Normal supply pressure must be at least 20 psi.
Toilet leaks a. Poor supply line connection. a. Review Step 9 of installation procedure.
b. Poor bowl to tank/floor connection. b. Review Step 4 through 7 of installation procedure.
Toilet does not a. Tank water level too high. a. Follow instructions to adjust water level.
shut off b. Float rod or float ball depressed by b. Readjust float rod.
tank cover.
c. Flush valve chain too tight, holding c. Readjust chain length as needed.
flush valve open.
d. Float rod interfering with flush valve d. Follow installation instructions to reduce water control flow
closing. rate, which will lift lowest position of float rod without
affecting water level.
e. Flush valve seat and/or flapper worn e. Replace flapper/flush valve assembly, as needed.
or deformed.
f. Sand or debris lodged in water f. Shut off water supply. Consult a plumber, if necessary.
control.
Noisy Flush a. Water control flow rate too restricted. a. Follow instructions to increase water control flow rate.
AMERICAN-STANDARD ONE-YEAR LIMITED WARRANTY
If inspection of this American-Standard plumbing product, within one year after its initial installation, confirms that it is defective in materials or
workmanship, American-Standard will repair or, at its option, exchange the product for a similar model.
This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should
check with a local building or plumbing contractor to insure local code compliance before installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse,
misuse, accident or other damage; if it was not installed in accordance with American-Standard's instructions; or if it has been modified in a manner
inconsistent with the product as shipped by American-Standard.
American-Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor
shall American-Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or
exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or
limitation of implied warranties, so this exclusion may not apply to you.)
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case
this warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or
that a service request (including a description of the product model and of the defect) be sent to the following address:
In the United States:
American Standard Inc.
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: (800) 442-1902
www.AmericanStandard-US.com
In Canada:
American Standard
2480 Stanfield Rd.
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: (800) 387-0369
www.AmericanStandard.ca
- 4 -
www.AmericanStandard.com.mx
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
730237-100 REV. Q
Loading...