American Standard RHO 2545102, LHO 2545202, RHO 2544102, LHO 2544202 Installation Manual

INSTALLATION INSTRUCTIONS

TOWN SQUARE® S INTEGRAL APRON TUB

60x30" RHO 2545102 / LHO 2545202 60x32" RHO 2544102 / LHO 2544202

HIGH GLOSS ACRYLIC SURFACE

Thank you for selecting American Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

BEFORE YOU BEGIN....

Your new bath is shipped to you after careful inspection. To ensure maximum performance and pleasure from this product, please follow the instructions and cautions.

Local building codes vary by location. Observe all local plumbing and building codes.

TOOLS & MATERIALS REQUIRED

TOOLS:

• Level

• Square

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

NOTE: Take extra care in handling surfaces of the bath. Use only non-abrasive cloths to avoid scratching.

• Screw Driver

• Standard Woodworking Tools

• Personal Safety Equipment

• Caulking Gun

MATERIALS:

• Nails

• Plumber’s Putty

• Silicone Sealant

• 1 x 3 or 2 x 4 Stringers

• Drop Cloth

• Mortar Mix or Grout

ROUGH-IN INFORMATION:

TOWN SQUARE APRON TUB

10"

(254 mm)

16"

(406 mm)

32"

(813 mm)

18-11/16" (475 mm)

STRINGER

HEIGHT

S INTEGRAL

2544102 / 2544202

60"

(1524 mm)

3-5/16" (85 mm)

3-1/2" (89 mm)

3" (76 mm)

3-3/16" (81 mm)

(483 mm)

19"

1" (25 mm)

3-3/8" (86 mm)

ROUGH-IN INFORMATION: 2545 TOWN SQUARE APRON TUB

15"

(381 mm)

30"

(762 mm)

2545102 / 2545202

10"

(254 mm)

3-3/8" (85 mm)

18-11/16" (475 mm)

STRINGER

HEIGHT

S INTEGRAL

60"

(1524 mm)

3-1/2" (89 mm)

3" (76 mm)

3-3/16" (81 mm)

(483 mm)

19"

1" (25 mm)

3-3/8" (86 mm)

SAVE FOR FUTURE USE

GENERAL SPECIFICATIONS FOR 2544102/202 TUB

INSTALLED SIZE

WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS. CUBE (FT

All product names listed herein are trademarks of AS America, Inc. unless otherwise noted. © AS America, Inc. 2018

)

20-7/16 x 43-1/4 In. (519 x 1098mm)

25-13/16 x 53-1/4 In.(656 x 1353mm)

38 Lbs./Sq.Ft. (186 Kgs/Sq.m)

60 x 32 x 19 In.

(1524 x 813 x 483mm)

74 Lbs. (34 Kg)

502 Lbs.(228 Kg)

51 Gal. (194 L)

12-3/4 In. (324mm)

10.18

28.00

GENERAL SPECIFICATIONS FOR 2545102/202 TUB

INSTALLED SIZE

WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS. CUBE (FT

)

23-13/16 x 53-1/4 In.(605 x 1353mm)

18-7/16 x 43-1/4 In. (468 x 1098mm)

37 Lbs./Sq.Ft. (179 Kgs/Sq.m)

60 x 30 x 19 In.

(1524 x 762 x 483mm)

70 Lbs. (32 Kg)

458 Lbs.(208 Kg)

47 Gal. (176 L)

12-3/4 In. (324mm)

10.18

26.39

755503-100

GENERAL INSTALLATION INFORMATION ...

1. When installing coordinating bath walls, additional studs may be required. Refer to those installation instructions prior to installing tub.

2. Bath walls are to be installed over stud walls.

3. Bath may only be installed in a recess or fold over edge type installation.

4. It is recommended that the 2544 and 2545 Town Square S Tub be set in a small bed of mortar or grout to compensate for uneven floors. Stringers will help level tub, but will not provide adequate support.

5. Take extra care when driving nails or screws to avoid damaging the tub.

INSTALLATION AND FRAMING INSTRUCTIONS:

A.) Locate studs as required. Ensure roughing-in

dimensions are proper, plumb, and square (Fig. 1). It is strongly recommended that an additional opening be provided for access to

the drain components.

Fig. 1

Each alcove stud

must be plumb

and square.

B.) As shown in Fig. 2, mark the position of the underside of the deck by tracing a line onto the studs at the height indicated, using a level or other suitable straight edge.

C.) With the top of the stringer touching the traced line, attach the stringer to the studs.

Fig. 2

18-3/4"

(476mm)

TUB DIMENSION ‘A’

Model 2545 30" (762mm)

Model 2544 32" (813mm)

28-1/2" (724mm)

30-1/2" (775mm)

D.) Install drain components to the bath following the manufacturer's instructions. See the roughing-in drawing for suggested opening size and location dimensions.

755503-100

+ 2 hidden pages