American Standard LAKELAND 4114.1 User Manual

Installation

Instructions

LAKELAND

SINGLE CONTROL KITCHEN
PULL-OUT FAUCET

Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.

4114.100

To ensure that your installation proceeds smoothly-­please read these instructions carefully before you begin.

TOOLS REQUIRED

Regular Screwdriver

INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON

1

CAUTION

(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).

Insert supply HOSES (2) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface.
Follow mounting instructions below to secure faucet to mounting surface.

(B) Installation less ESCUTCHEON (1). Discard ESCUTCHEON with PUTTY PLATE (1). Insert supply HOSES (2) and
SHANK (3) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.

Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD
is centered.

Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.

Turn off hot and cold water
supplies before beginning.

Phillips Screwdriver

7

Adjustable Wrench

Certified to comply with ANSI A112.18.1M

M 9 6 8 4 7 0 R E V. 1. 5

Plumbers' Putty or Caulking

7

1

PUTTY

A

SPOUT BASE

2

3

SINK OR

MOUNTING

4

5

8

6

SURFACE

B

3

2

4

5

8

6

MAKE WATER SUPPLY CONNECTIONS

2

Turn off hot and cold water supplies before beginning.

Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply to Hot (Marked with a Red Line)
and right supply to Cold wall supply. Use
adjustable wrench to tighten connections.
Do not over tighten.

Faucet supplies are 21" long from faucet base.

Note: If additional supply length is
required, installer must purchase
additional parts separately.

Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.

CONNECT SPRAY HOSE

3

Slide COUPLING NUT (1) onto HOSE (2)

Place WASHER (3) into COUPLING NUT (1)
on HOSE (2). Thread COUPLING NUT (1) onto
HAND SPRAY (4) and tighten.
(May already be assembled).

2

1

COLD

HOT

3

1

6

5

4

Feed small end of HOSE (2) through BODY (5) so
HAND SPRAY (4) rests inside SPRAY HOLDER (6).

Thread HOSE END (7) onto OUTLET HOSE ADAPTER (8)
and tighten.

With HAND SPRAY (4) seated in SPRAY HOLDER (6),
install WEIGHTS (9) onto HOSE (2) using two SCREWS (10).
Locate the WEIGHTS (9) two feet (2') from the underside of
the sink deck. Tighten SCREWS (10) firmly.

TEST INSTALLED FAUCET

4

Move HANDLE (1) down into "off"
position.

Turn on water supplies.
Check connections for leaks (See

Section 5).

With HANDLE (1) down in "off"
position.

Pull HAND SPRAY (2) from FAUCET (5)
and disconnect HAND SPRAY (2). Be
careful not to lose WASHER (7). Pull
HOSE (3) (HOSE should pull
approximately 2 feet) and direct open
HOSE END (4) into sink.

6

1

2

7

3

5

2

24"

8

7

9

Operate handle up and down, in COLD and HOT positions, to
flush water lines thoroughly.

Place WASHER (7) into HOSE END (4) and connect
HAND SPRAY (2) to HOSE END (4). Place HAND SPRAY (2)
back into faucet.

Check HAND SPRAY (2) operation:

10

2

With faucet on push front of BUTTON (6) for a broad
cleansing spray.

4

M 9 6 8 4 7 0 R E V. 1. 5