American Standard Hampton 7411.712, Hampton 7411.702, Hampton 7411.722, Hampton 7411.732 User Manual
Installation
Instructions
7411.702
Centerset Lavatory Faucet with
EverClean™ Finish & SpeedConnect™ Drain
Congratulations on purchasing your American Standard faucet with
EverClean finish and SpeedConnect drain, two features found only
on American Standard faucets.
EverClean Finish
• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)
*Your new American Standard faucet is designed to work only with the SpeedConnect drain. Heplful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Required tools
SpeedConnect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
7411.712
7411.722
7411.732
Certified to comply with ANSI A112.18.1
US60402 Rev.1.1
INSTALL FAUCET
1
Turn off hot and cold water supplies before beginning.
Insert FAUCET (1) and CABLE CONNECTOR (2) through
mounting holes of Sink or mounting surface.
Assemble LOCKNUTS (3) onto SHANKS (4) from under
side of Sink. Hand tighten firmly.
(HAND TIGHTEN)
CAUTION
Turn off hot and cold water
supplies before beginning.
Fig. A.
Fig. B.
3
4
Fig. B.
Adjustable Wrench Screwdriver Channel Locks
Tubing Cutter
Fig. A.
POP-UP
CABLE
4
SINK OR
MOUNTING
SURFACE
3
2
1
2
POP-UP DRAIN
2
Fig. A. Fig. B.
Remove CLEAR PLASTIC COVER (1).
Remove CARDBOARD SPACER (2) from under
DRAIN POP-UP (3).
Tighten TAILPIECE (4) on DRAIN BODY before
installing DRAIN BODY.
REMOVE FLANGE
3
Thread FLANGE (1) counter-clockwise and remove
FLANGE (1) and FOAM GASKET (2) from drain
body.
Fig. A.
Thread LOCKNUT (3) clock-wise to bottom of
drain body. Push GASKET (4) down against
LOCKNUT (3).
Fig. B.
Fig. B.
1
3
2
Fig. A. Fig. B.
1
2
4
3
DRAIN
BODY
4
INSTALL DRAIN FROM
4
BELOW FIXTURE
From under side of SINK
install DRAIN BODY (1) up
through drain outlet.
Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face towards
the rear of the SINK.
Install FOAM GASKET (3) and
FLANGE (4) onto drain body
from above SINK and tighten
FLANGE (4) firmly.
FLANGE GASKET AND POP-UP KNOB
6
Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. A.
POP-UP KNOB (1) must be fully down. Fig. B.
4
3
TIGHTEN LOCKNUT
REAR OF SINK
DRAIN
OUTLET
5
Tighten LOCKNUT (1) firmly with Adjustable
Wrench or Channel Locks.
1
2
Fig. A. Fig. B.
WHITE FOAM
GASKET
NOT VISIBLE
DRAIN
FLANGE
1
DOWN
1
US60402 Rev.1.1
2
Loading...