American Standard Renaissance 2241, Compact 2149.012, 3505, Two-Piece Toilets with Aquameter, Compact 3505 User Manual

INSTALLATION INSTRUCTIONS

For Two-Piece Toilets with Aquameter™ Fill Valve

RENAISSANCE 2241
COMPACT 2149.012, 3505
COLONY 2388 / 2399 / 2359
COLONY AFTON 2329.016

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations may
require professional help.) Also be sure your installation conforms to local codes

!

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY
HANDLE WITH CARE!

NOTE:

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure
Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level

Pictures may not exactly define contour of china and components.

1 REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE:
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

NOTE:

Mounting surface must be clean and level before new toilet is installed!

ROUGHING-IN DIMENSIONS:

NOTE:

be as listed below:

For 4010.010/4310.016 Tanks: A = 254mm (10")
For 4014/4314 Tanks: A = 356mm (14")
For 4010.012/4392.016 and all other Tanks: A = 305mm (12")

Distance from wall to closet flange centerline must

FINISHED WALL

SUPPLY

AS

REQ'D.

If replacing valve, first shut off main water supply!

32

CLOSET FLANGE

A

CLOSET BOLTS

SAVE FOR FUTURE USE

A

Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2004

FINISHED
FLOOR

INSTALL CLOSET BOLTS

Install closet bolts in flange channel, turn 90°,
and slide into place 6" (152 mm) apart and
parallel to wall.

Saniwares

730237-100 REV. Q

SEALANT

WAX RING

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent
damage), and install wax ring evenly around
waste flange (horn), with tapered end of ring
facing toilet. Apply a thin bead of sealant
around base flange.

54

NUT

TAPERED
WASHER

CLOSET

BOLT

FLANGE

POSITION TOILET ON FLANGE

a. Unplug floor waste opening and install toilet on closet flange
so bolts project through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers
marked "THIS SIDE UP"

must

face up!

6

BOLT CAP

CLOSET FLANGE

CLOSET BOLT

WASHER

NUT

INSTALL TOILET

a. Position toilet squarely to wall and, with a
rocking motion, press bowl down fully on wax
ring and flange. Alternately tighten nuts until
toilet is firmly seated on floor.

!

CAUTION:

DO NOT OVERTIGHTEN NUTS

OR BASE MAY BE DAMAGED!

b. Install caps on washers. (If necessary, cut
bolt height to size before installing caps.)
c. Smooth off the bead of sealant around
base. Remove excess sealant.

For Tanks/Bowls using Speed

7a

Connect System (Tank
mounting bolts pre-installed).

TANK MTG.
BOLTS PRE­INSTALLED

WASHER

NUT

RUBBER
GASKET

INSTALL TANK

a. Install large rubber gasket
over threaded outlet on bottom
of tank and lower tank onto bowl
so that tapered end of gasket fits
evenly into bowl water inlet
opening, and tank mounting
bolts go through mounting holes.
Secure with metal washers and
nuts.
b. With tank parallel to wall,
alternately tighten nuts until tank
is snugged down evenly against
bowl surface.

!

DO NOT OVERTIGHTEN NUTS MORE

THAN REQUIRED FOR A SNUG FIT!

CAUTION:

For all other Tanks/Bowls

7b

RUBBER
WASHER

TANK MTG.

BOLTS

WASHER

NUT

RUBBER
GASKET

INSTALL TANK

a. Install large rubber gasket
over threaded outlet on bottom
of tank and lower tank onto bowl
so that tapered end of gasket fits
evenly into bowl water inlet
opening.
b. Insert tank mounting bolts
and rubber washers from inside
tank, through mounting holes,
and secure with metal washers
and nuts.
c. With tank parallel to wall,
alternately tighten nuts until tank
is snugged down evenly against
bowl surface.

!

DO NOT OVERTIGHTEN NUTS MORE

THAN REQUIRED FOR A SNUG FIT!

CAUTION:

8

INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.

- 2 -

730237-100 REV. Q