American Standard Ceramix 2021.831 User Manual
Installation
TM
KITCHEN FAUCETS
HI-FLOW SPOUT
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
Instructions
2021.831
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
TOOLS REQUIRED
Channel Locks
FAUCET INSTALLATION
1
CAUTION
Turn off hot and cold water supplies before beginning.
This faucet permits an interchangeable mounting of
each integral component -- spout, valve, and hand spray-to suit the particular installation requirements.
Before starting installation, place each component
loosely into the holes of the kitchen sink to select the
most desirable arrangement.
ROUGHING-IN
DIMENSIONS
9-9/16
12" MAX
12
MAX
2-3/16
DIA
2 DIA.
27/32
DIA.
1-1/16 MAX
1-1/8 DIA
1-1/4 MAX
Adjustable Wrench
VALV E
1-1/4 MIN DIA
MTG HOLE
MTG SURFACE
1-3/4 MAX
FLEXIBLE HOSE
TO SPOUT
C/L OF
2
10
8-9/16
13-7/8
Certified to comply with ASME A112.18.1M
Plumbers' Putty or Caulking
Phillips Screwdriver
VALVE INSTALLATION
Remove VALVE NIPPLE (1),
SEAL WASHER (2), LOCKNUT (3)
and MOUNTING ASSEMBLY (4) from
threaded STUD (5) of valve.
Insert supply TUBES (6) and threaded
STUD (5) through hole in sink.
Make sure black RUBBER RING (7)
is properly seated in recess of base.
Orient valve so that threaded STUD (5)
is centrally located towards the rear of
sink, then assemble MOUNTING
ASSEMBLY (4) and thread LOCKNUT (3)
onto STUD (5) from underside of sink.
Hand tighten LOCKNUT (3) and check
that rotation of HANDLE (8) from HOT
to COLD is centered. Secure valve
position by tightening LOCKNUT (3)
firmly (spread TUBES (6) for better
access to LOCKNUT (3).
Bend TUBES (6) to meet supplies. Use
palm of hand to support TUBES (6)
while bending to avoid kinking.
Attach VALVE NIPPLE (1) with SEAL
WASHER (2) to threaded STUD (5).
M66241 REV.1.1
8
RECESS
7
5
4
3
2
1
6
HOT COLD
3/8 OD COPPER
BENDABLE
SPOUT BASE INSTALLATION
3
Remove ESCUTCHEON (1) with RUBBER
RING (2) and insert SPOUT BASE (3) through
hole from underside of Sink. Threads
of SPOUT BASE (3) should extend at least
5/16-inch above mounting surface. If necessary,
adjust LOCKNUT (4).
Place RUBBER RING (2) into ESCUTCHEON (1)
recess and thread ESCUTCHEON (1) onto
SPOUT BASE (3) until snug against
internal stop.
Turn SPOUT BASE (3) so that the side
INLET NIPPLE (5) is directed towards
valve. Center SPOUT BASE (3) and
tighten LOCKNUT (4).
Place SEAL WASHERS (6) into coupling
nuts of FLEXIBLE HOSE (8) and connect to
side INLET NIPPLE (5) and VALVE NIPPLE (7).
SPOUT INSTALLATION
4
SINK OR
MOUNTING
SURFACE
RUBBER WASHER
4
7
6
6
8
1
2
5/16'' MIN.
3
5
Check that both O-RINGS (1) are properly seated on the
valve center.
Check that the DIVERTER PLUG (2) is free and can move
up and down.
Push the SPOUT SUB-ASSEMBLY (3) on to the SPOUT BASE (4)
and tighten the SPOUT NUT (5) until snug on SPOUT BASE (4).
Place SPRAY HOLDER (6) into the appropriate mounting hole,
assemble WING NUT (7) onto shank of SPRAY HOLDER (6)
from underside of sink and secure by tighting WING NUT (7).
Feed SPRAY HOSE (8) through SPRAY HOLDER (6) and attach COUPLING
NUT (9) of SPRAY HOSE (8) to HOSE ADAPTER (10). Tighten COUPLING
NUT firmly (9).
Make certain that SPACER WASHER (11) and RUBBER WASHER (12)
are attached to SPRAY HOSE (8) and thread SPRAY HEAD (13) to NUT (14).
Tighten NUT (14) firmly.
SUPPLY CONNECTIONS
5
Bend 3/8” SUPPLY TUBES to meet water supplies valves.
Use palm of hand to support TUBES while bending to avoid kinking.
Connect inlet TUBES to water supplies with appropriate connectors.
Connect left TUBE to HOT water supply, and the right TUBE to the
COLD water supply.
Note: If additional supply length is required, installer must purchase
additional parts separately.
3
13
12
11
5
INSTALL
14
2
1
4
6
8
10
7
9
3/8 O.D.
SUPPLIES
HOT
COLD
COMPRESSION
NUT
FERRULE
M66241 REV.1.2
Loading...