American Standard Cadet Elite Whirlpool 2774E User Manual

CADET ELITE™ 6’ x 42
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
CADET ELITE™ 6’ X 42 WHIRLPOOL
Comfortable bathing design with form-fitted backrest and molded in armrests
2774E (specify White 020, Bone 021, or
Linen 222)
2.0 HP self-draining pump/motor
with dry run seal
Eight multi-directional and flow adjustable jets including: Two high performance Ideal-flowJets Six interchangeable Flex-jets
Two silent air volume controls
Deck-mounted On/Off control
Complete factory installed and tested
whirlpool system
2774EC (specify White 020, Bone 021, or
Linen 222)
Same as above with the StayClean whirlpool system featuring Antimicrobial AlphaSan®
Nominal Dimensions: 72 x 42 x 19-3/4" (1829 x 1067 x 502mm)
© 2003 American Standard Inc.
HD-009
SPS 2774E
Revised 6/03
Compliance Certifications ­Meets or Exceeds the Following Specifications:
Underwriters Laboratories - Hydromassage Bathtubs UL 1795
ASME A112.19.7M for Whirlpool Appliances
ANSI Z124.1 for Plastic Bathtubs
ASTM E162 for Flammability
NFPA 258 for Smoke Density
* See American Standard Faucet Selector
NOTE: Roughing-in dimensions and product specifications shown on reverse side of page.
Components Needed:
Bath Filler*: (specify finish) Bath Drain: BATH-DRAIN
(specify Chrome 002, Polished Brass 099,
or Satin 295)
Custom Accessories Available:
Pulse Jet Kit: PULSE-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
Soft Jet Kit: SOFT-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
Six Foot Apron: 6FT-APRON (specify White
020, Bone 021, or Linen 222)
E-Z-InstallWhirlpool Heater - EZHEAT-100 Tile Bead Kit: TILE-BEAD
NOTE: E-Z-InstallWhirlpool Heater is designed to maintain water temperature during operation. It will not heat cold water to desired bathing temperature.
CADET ELITE™ 6’ x 42
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUPPORT OF BATH BY SUMP BEDDING. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
OPTIONAL 3 WALL TILING BEAD KIT No. TILE-BEAD AND APRON No. 6FT-APRON AVAILABLE AND MUST BE ORDERED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1 These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.
SEE FITTING
SPECS FOR
DIMENSIONS
1067mm
(42)
229mm
FINISHED
533mm
(21)
(9)
WALL
19 mm
(3/4)
305 mm
(12)
PROVIDE ACCESS TO PUMP FOR
SERVICING ON ALL INSTALLATIONS
1829 mm
RECOMMENDED FITTING LOCATION
229 mm
(9)
CUTOUT IN FLOOR FOR DRAIN
(72)
64 X 330mm (2-1/2 x 13")
FOR PIER OR ISLAND
INSTALLATIONS ONLY
PUMP
ON/OFF SWITCH
C/L OF
SUPPLIES
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
1651 & 1981mm
(65 & 78)
57mm (2-1/4)
C/L OF DRAIN
C/L OF OVERFLOW
89mm (3-1/2)
ROUGH
FLOOR
INTEGRAL
SUPPORT
GENERAL SPECIFICATIONS FOR 2774E WHIRLPOOL
INSTALLED SIZE
WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW MIn. OPERATING GAL. BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS.
CUBE (FT3)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
502mm (19-3/4)
FEET
38mm
(1-1/2)
(8) JETS
305mm
(12)
102mm
(4)
1-1/2 N.P.T.M.
THREADS
1-1/2 O.D.TAILPIECE
(1829mm x 1067 mm x 502mm)
50 x 27 In. (1270 mm x 686 mm)
42 Lbs./Sq. Ft. (203 Kgs/Sq. m.)
IN-LINE HEATER REMOVABLE BLANK
464 mm (18-1/4)
117 mm
(4-5/8)
OUTLINE OF CUTOUT 1791mm x 1029mm (70-1/2 X 40-1/2)
(2) AIR VALVES
ALT. FITTING
LOCATION #1
C/L OF SHOWER ARM
C/L OF VALVES
C/L OF SPOUT
70 mm (2-3/4)
72 x 42 x 19-3/4 In.
137 Lbs. (62 Kg.)
821 Lbs. (372 Kg.)
82 Gal. (310 L.) 66 Gal. (256 L.)
65 x 33 In. (1651 x 838mm)
13 In. (330 mm)
27.8
55.5
2.1 HP, 14.4 AMPS, 120V.PUMP
LEVELING STRINGER NOT FOR SUPPORT
Loading...