COLONY™ RIGHT HEIGHT™
ELONGATED 10" ROUGH-IN TOILET
VITREOUS CHINA
COLONY™ RIGHT HEIGHT™ ELONGATED 10" ROUGH-IN TOILET
2359.010
•Vitreous china
•Low-consumption (6.0 Lpf/1.6 gpf)
•16-1/2" rim height for accessible applications
•10" roughing-in
•Elongated siphon action jetted bowl
•Fully glazed 2" trapway
•American Standard Aquameter™ Water Control
•Color-matched trip lever
•Sanitary bar on bowl
•2 bolt caps
•100% factory flush tested
3370.016 Bowl
4310.016 Tank
Nominal Dimensions: |
FINISHED WALL |
|
|
|
|
|
|
|
|
|
|
705 x 508 x 781mm |
|
(27-3/4) |
|
|
|
(27-3/4" x 20" x 30-3/4") |
|
|
|
|
|
|
|
705mm |
|
|
|
|
19mm ± 6mm |
|
|
|
508mm |
|
(3/4 ± 1/4) |
|
|
|
|
Fixture only, seat and supply by others |
(7-1/4) |
|
|
|
(20) |
|
184mm |
|
|
|
|
Compliance Certifications - |
|
(18-1/2) |
|
|
|
Meets or Exceeds the Following Specifications: |
|
470mm |
|
|
|
|
|
|
|
C/L |
|
• ASME A112.19.2M for Vitreous China Fixtures - |
|
C/L OF SEAT POST HOLES |
|
|
|
|
140mm (5-1/2 CENTERS) |
|
|
||
includes Flush Performance, Ball Pass Diameter, |
|
|
|
|
781mm |
Trap Seal Depth and all Dimensions |
|
|
|
SUPPLY |
(30-3/4) |
|
|
|
AS |
|
|
|
79mm 1/8)-(3 |
|
|
REQ'D |
|
|
|
419mm |
|
|
|
|
|
|
(16-1/2) |
|
|
|
|
|
|
*203mm(8) |
375mm |
|
|
|
|
(14-3/4) |
|
|
16mm |
|
152mm |
|
|
|
|
(6) |
|
||
|
(5/8) |
|
|
||
|
|
|
|
||
|
|
|
FINISHED |
|
|
|
178mm |
311mm |
FLOOR |
|
235mm |
|
(7) |
(12-1/4) |
|
|
(9-1/4) |
|
|
|
|
|
|
|
254mm |
C/L OF OUTLET |
|
|
|
|
(10) |
|
|
|
|
|
|
|
|
|
To Be Specified:
Color: White
Seat: American Standard #5324.019 “Rise and Shine” solid plastic closed front seat with cover.
Seat: American Standard #5311.012 “Laurel” molded closed front seat with cover.
Alternate Seat:
Supply with stop:
NOTES:
THIS COMBINATION IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 254MM (10") FROM FINISHED WALL TO C/L OF OUTLET.
* DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED. SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerance established by ANSI Standard A112.19.2
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE BUILDING FACILITIES-CHECK LOCAL CODES.
|
K91 |
|
|
© 2008 AS America Inc. |
Revised 2/08 |
||
|