American Standard 3120.019 User Manual
YORKVILLE™ ELONGATED
749 mm
(29 -1/2)
235 mm
(9- 1/4)
356 mm
(14 )
381 mm
(15 )
470 mm
(18 -1/2)
648 mm
(25 -1/2)
813 mm
(32 )
C/L OF SE AT
POS T HOLE S
140 mm (5 -1/2)
CEN TER
FIN ISHED WALL
FIN ISHED
FLO OR
152 mm
(6)
64m m (2-1 /2)
32 4mm
(12 -3/4)
C/L OF 1/ 2" DI A HOLE S
152 mm (6) CENT ERS
76m m
(3)
76m m
(3)
*
222 mm
(8- 3/4)
102 mm
(4)
C/L OF
WAS TE
OUT LET
13 x 19mm
(1/ 2 x 3/ 4)
SLO TS
FLE X
SUP PLY
AS REQ.
C/L
19mm ± 6mm
(3/4 ± 1/4 )
279m m
(11)
495m m
(19- 1/2)
PRESSURE-ASSISTED TOILET
❏ 2320.101
• Vitreous china
• Low-consumption (6.0 Lpf/1.6 gpf)
• Floor-mounted, back-outlet toilet
• Elongated bowl
• Pressure-assisted siphon jet ush action
• Side-mounted chrome trip lever
• Close-coupled ushometer tank*
• Speed Connect® tank/bowl coupling system
• 4 bolt caps
• Fully glazed 2" ballpass trapway
• 10" x 12" water surface area
• 100% factory ush tested
❏ 3120.019 Elongated bowl with four bolt
caps and two oor screws
❏ 4099.100 Flushometer tank complete with
coupling components
YORKVILLE™ ELONGATED
PRESSURE-ASSISTED TOILET
VITREOUS CHINA
Component parts:
❏ 735084-400 Tank cover (specify color)
Nominal Dimensions:
813 x 495 x 749mm
(32" x 19-1/2" x 29-1/2")
Alternate Congurations:
❏ 4099.700 Tank and tank cover only
with tank cover locking device
❏ 4099.800 Tank and tank cover only
with right hand trip lever
Fixture only, seat and supply by others
Recommended working pressure range 20 psi - 80psi
Compliance Certications Meets or Exceeds the Following Specications:
• ASME A112.19.2 for Vitreous China Fixtures
To Be Specied:
❏ Color: ❏ White ❏ Bone ❏ Linen
❏ Silver ❏ Fawn Beige ❏ Black
❏ Seat: American Standard #5324.019
Elongated “Rise and Shine” (with easy to clean
lift-off hinge system) solid plastic closed front
seat with cover.
❏ Seat: American Standard #5325.024
Elongated “Rise and Shine” (with easy to clean
lift-off hinge system) solid plastic open front
seat with cover.
❏ Alternate Seat:
❏ Supply with Stop:
* Flushmate III tank system by Flushmate® Div. of Sloan Valve Co
© 2008 AS America Inc.
Replaces 2320.100
NOTES:
WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITEFELT (WAX RING NOT RECOMMENDED) .
SUPPLY NOT INCLUDED WITH FIX TURE AND MUST BE ORDERED
SEPARATELY.
DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED.
*
FOR ADDITIONAL INFORMATION REFER TO INSTALLATION
INSTRUCTIONS SUPPLIED.
IMPORTANT: Dimensions of xtures are nominal and may vary within
the range of tolerances established by ANSI Standard A112.19.2. These
measurements are subject to change or cancellation. No responsibilit y is
assumed for use of superseded or voided pages.
M43
Revised 2/08
Loading...