American Standard 2425E-LHO, 2425EC-RHO, 2425EC-LHO, 2425E-RHO User Manual

WILLIAMSBURG ELITE™ 5’ INTEGRAL APRON

WHIRLPOOLS BY AMERICAN STANDARD

HIGH GLOSS ACRYLIC

WILLIAMSBURG ELITE™ 5’ INTEGRAL APRON
WHIRLPOOL

Comfortable bathing design with form-fitted
backrest and molded-in armrests

❏ 2425E-LHO Left Hand Drain Outlet

(specify White 020, Bone 021, or Linen 222)

❏ 2425E-RHO Right Hand Drain Outlet

(specify White 020, Bone 021, or Linen 222)

• Acrylic with fiberglass reinforcement

• Integral apron with removable access panel

• Integral three-sided, tiling / water retention

flange

• 1.5 HP self-draining pump/motor
with dry run seal

• Eight multi-directional and flow adjustable jets
including:
Two high performance Ideal-flow™ Jets
Six interchangeable Flex-jets™

• Two silent air volume controls

• Deck-mounted On/Off control

• Complete factory installed and tested

whirlpool system

❏ 2425EC-LHO Left Hand Drain Outlet

(specify White 020, Bone 021, or Linen 222)

❏ 2425EC-RHO Right Hand Drain Outlet

(specify White 020, Bone 021, or Linen 222)

• Same as above with the StayClean™
whirlpool system featuring Antimicrobial
AlphaSan®

Nominal Dimensions:
60” x 32” x 21-1/2”

(1524 x 813 x 546mm)

© 2003 American Standard Inc.

HD-016

SPS 2425E-LHO/RHO

Revised 6/03

Compliance Certifications ­Meets or Exceeds the Following Specifications:

• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795

• ASME A112.19.7M for Whirlpool Appliances

• ANSI Z124.1 for Plastic Bathtubs

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

* See American Standard Faucet Selector

NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.

Components Needed:

❏ Bath Filler*: (specify finish)
❏ Bath Drain: BATH-DRAIN

(specify Chrome 002, Polished Brass 099,

or Satin 295)

Custom Accessories Available:

❏ Pulse Jet Kit: PULSE-JET (two per kit, specify

White 020, Bone 021, or Linen 222)

❏ Soft Jet Kit: SOFT-JET (two per kit, specify

White 020, Bone 021, or Linen 222)

❏ E-Z-Install™ Whirlpool Heater - EZHEAT-100

NOTE: E-Z-Install™ Whirlpool Heater is designed to
maintain water temperature during operation. It will not
heat cold water to desired bathing temperature.

WILLIAMSBURG ELITE™ 5’ INTEGRAL APRON

WHIRLPOOLS BY AMERICAN STANDARD

HIGH GLOSS ACRYLIC

© 2003 American Standard Inc.

NOTES:

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE
INSTALLATION. SUPPORT OF BATH BY SUMP BEDDING. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.

REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.

IMPORTANT:

Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or
voided leaflet.

10-1/4

(260mm)

SEE FITTING

SPECS FOR

DIMENSIONS

32

(813mm)

(19mm)

FINISHED

WALL

60

12

(305mm)

3/4

(229 mm)

CUTOUT IN FLOOR FOR DRAIN

(1524mm)

(8) JETS

9

PUMP

WATER
RETENTION
FLANGE
(3 SIDES)

16

(406mm)

ON/OFF
SWITCH

C/L OF

SUPPLIES

OPTIONAL TO

FINISHED FLOOR

USUALLY BETWEEN

65 & 78

(1651 & 1981mm)

TOP OF

DECK

INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT

PUMP 1.6 HP, 9.7 AMPS,120V.

(76mm)

RETENTION

C/L OF
OVERFLOW

ROUGH

FLOOR

BATH

SUPPORT

MATERIAL

3

C/L OF DRAIN

1" WATER

FLANGE

(3 SIDES)

3-1/2

(89mm)

21-1/2

(546mm)

1-1/2 O.D.TAILPIECE

IN-LINE HEATER
REMOVABLE
BLANK

12

(305mm)

OPT.

1-1/2 N.P.T.M.

THREADS

(2) AIR VALVES

C/L OF
SHOWER ARM

FINISHED

C/L OF
VALVES

4

(102 mm)

(70mm)

WALL

C/L OF
SPOUT

2-3/4

GENERAL SPECIFICATIONS FOR 2425E WHIRLPOOL

60 x 32 x 21-1/2 (1524 x 813 x 546mm)

16-1/4 x 38-1/4 (413 x 972mm)

26-1/4 x 52-1/2 (667 x 1334mm)

115 Lbs. (52 Kg.)

574 Lbs. (258 Kg.)

55 Gal. (208 L.)

45 Gal. (171 L.)

43 Lbs./Sq.Ft. (208 Kgs./Sq.m)

3

)

WHIRLPOOL ELECTRICAL SPECIFICATIONS

ACCESS TO PUMP/MOTOR
THROUGH REMOVABLE
FRONT ACCESS PANEL

TILING
FLANGE

(117mm)

4-5/8

21-1/4

(540mm)

REF.

DIM

LEVELING STRINGER
NOT FOR SUPPORT

15 (381mm)

20.8

35.3

UNDERSIDE
OF DECK