|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
© Grindmaster Corporation, 2004 |
0804 Form # PD-336-03 |
|||||||
PRINTED IN PRC |
Part # 92610 |
|||||||
TABLE OF CONTENTS |
|
|
Product Description........................................... |
3 |
|
Safety Instructions ........................................... |
4 |
-6 |
User Operational Controls .............................. |
7 |
|
Installation Instructions ................................... |
8 |
|
Operating Instructions ..................................... |
9 |
-10 |
Adjustments ...................................................... |
11 |
|
Cleaning & Maintenance.................................. |
12 |
|
User Replaceable Parts .................................... |
12 |
|
Troubleshooting ................................................ |
13 |
|
Specifications ..................................................... |
14 |
|
Warranty ........................................................... |
16 |
|
Page 2 |
Commercial /OCS Pod Brewer |
|
|
Product Description
Thank you for purchasing Grindmaster’s Commercial/OCS Pod brewer. The OPOD is a digitally controlled commercial coffee brewer that brews one cup of coffee or tea at a time. It has been designed to maximize your drinking pleasure by brewing a cup of coffee or tea of your choice under optimum brewing conditions. This brewer uses coffee or tea pods ranging in size from
57 mm to 61 mm. Pods are available from your retailer in many different flavors.
Note: This section of the manual describes the brewer in general terms. Specifics are described in detail in other sections of this manual.
The OPOD can be plumbed into a water supply. If a water line is not available, the brewer can be used as a pourover. The brewer uses a 15 amp, 120 volt power line. If the brewer is plumbed in, then it will refill the reservoir itself automatically. If it is used in pourover mode, then the user must manually refill the reservoir as needed.
The operating principle of this machine is that a user places their coffee mug on the drain tray then places a fresh coffee or tea pod in the brew chamber. The user then closes the chamber. Then the user selects, on the STRENGTH selector switch, their choice of coffee brewing strength; LIGHT, MEDIUM, or STRONG. If tea is desired, then the selector switch must be placed on TEA selection. Once the selection is made, the Brew button is pressed and released. The OPOD digital control system delivers approximately 8 fluid ounces (237 ml) of optimum brew temperature water through the pod to create a fresh cup of coffee or tea in approximately 40 seconds.
Another cup of coffee or tea can be brewed immediately after replacing the spent pod.
The selector switch below the brew switch controls the machine functions required to obtain optimum flavor of coffee and brew strength for each consumer as well as the optimum brewed cup of tea.
All brew volumes are factory set to brew approximately 8 fluid ounces
(237 ml) of finished beverage depending on the type of pod used. Differences in pods affect the amount of water absorbed into the pod. Dispensing hot water only, without the use of a pod, will result in approximately 9 fluid ounces (266 ml) of hot water dispensed.
Commercial /OCS Pod Brewer |
Page 3 |
|
|
Safety Instructions
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
The label below (P/N 92645) was packed with the coffee brewer at the factory. It is provided so that it can be placed in close proximity to the brewer to inform users and operators of the potential hazards associated with HOT beverages. Additional labels can be ordered as needed (Part # 92645).
Page 4 |
Commercial /OCS Pod Brewer |
|
|
Safety Instructions (cont.)
Permanent Warning Decals and Precautions
The following labels were applied to your brewer when it was shipped from the factory. The labels should remain in good readable condition at all times. If one of the labels is missing or damaged, order a replacement label immediately.
Located above the drip tray and on top of the reservoir lid
(Part # 92572)
Located on the back of the machine
(Part # 92476)
Commercial /OCS Pod Brewer |
Page 5 |
|
|
Loading...