Illustra Flex Series 3MP and 8MP Indoor and Outdoor
Dome Cameras
Quick Start Guide
Notice
Please read this manual thoroughly and save it for future use before attempting to connect or operate
this unit.
The information in this manual was current when published. The manufacturer reserves the right to
revise and improve its products. All specifications are therefore subject to change without notice.
Copyright
Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced,
translated or reduced to any electronic medium or machine-readable form, in whole or in part, without
prior written consent of Tyco Security Products.
© 2018 Tyco Security Products. All rights reserved.
Tyco Security Products
6600 Congress Avenue
Boca Raton, FL 33487 U.S.A.
Customer Service
Thank you for using American Dynamics products. We support our products through an extensive
worldwide network of dealers. The dealer through whom you originally purchased this product is your
point of contact if you need service or support. Our dealers are empowered to provide the very best in
customer service and support. Dealers should contact American Dynamics at (800) 507-6268 or
(561) 912-6259 or on the Web at www.americandynamics.net.
Trademarks
The trademarks, logos, and service marks displayed on this document are registered in the United
States [or other countries]. Any misuse of the trademarks is strictly prohibited and Tyco Security
Products will aggressively enforce its intellectual property rights to the fullest extent of the law,
including pursuit of criminal prosecution wherever necessary. All trademarks not owned by Tyco
Security Products are the property of their respective owners, and are used with permission or
allowed under applicable laws.
Product offerings and specifications are subject to change without notice. Actual products may vary
from photos. Not all products include all features. Availability varies by region; contact your sales
representative.
Table of Contents
Illustra Flex Series 3MP and 8MP Indoor Dome Camera 1
Product features 1
Product overview 1
Installation 5
Illustra Flex Series 3MP and 8MP Outdoor Dome Camera 10
Product features 10
Product overview 10
Installation 14
System requirements 20
Network Connection 21
Default IP Addr ess 21
DHCP 22
Managing cameras with the Illustra Connect tool 23
Network Topology 25
Appendix A: Technical Specifications 26
Appendix B: Stream Resolutions 30
Warning
• These units operate at AC 24V/ PoE.
• Installation and service should be performed only by qualified and experienced technicians
and comply with all local codes and rules to maintain your warranty.
• To reduce the risk of fire or electric shock, do not expose the product to rain or moisture.
• Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral
detergent and wipe with a dry soft cloth.
• Do not apply benzene or thinner to the camera, which may cause the surface of the unit to
be melted or lens to be fogged.
• Avoid aligning the lens to very bright objects (for example, light fixtures) for long periods of
time.
• ITE is to be connected only to PoE networks without routing to the outside plant.
• The power supply shall be approved for ITE NEC Class 2 or LPS with a rating of 24VAC,
550mA minimum and 50 degrees Celsius.
• Video Out connection should be intra-building only.
• Avoid operating or storing the unit in the following locations:
• Extremely humid, dusty, or hot/cold environments. Recommended operating
temperature is:
• Indoor Minidome: -20˚C to 50˚C (-4˚F to 122˚F)
• Outdoor Minidome: -50˚C to 50˚C (-58˚F to 122˚F)
• Power over Ethernet (PoE) does not support heater.
• Near sources of powerful radio or TV transmitters.
• Near fluorescent lamps or objects with reflections.
• Under unstable or flickering light sources.
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable
in the European Union and other European countries with separate collection systems). This
product should be disposed of, at the end of its useful life, as per applicable local laws, regulations,
and procedures.
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Illustra Flex Series 3MP and 8MP Indoor Dome
Camera
This chapter provides product features, installation procedures, and connection information regarding
the Illustra Flex Series Indoor Dome cameras.
Product features
Len cases require special care when handling and cleaning to avoid scratches. For information on
bubble handling and cleaning, see 8200-1174-01 Bubble Clearing Procedure Application Note.
Go to https://illustracameras.com/products.
From the Products page, select your camera product range and then select your camera model. Click
Downloads and search for Bubble Handling and Cleaning Procedure.
Product overview
This chapter explains the features and installation of the Illustra Flex Indoor Dome cameras. Product
code and description of the camera is provided in the table below.
Table 1 Product code and description of the Illustra Flex Indoor Dome camera
Product
Code
IFS03D1ICWTT
IFS08D2ICWTT
Figure 2 Physical dimensions of the Illustra Flex Indoor Dome camera (mm)
Model Name Description
Illustra Flex 3MP Indoor
Mini-Dome
Illustra Flex 4K Indoor
Mini-Dome
Illustra Flex 3MP Mini-dome, 2.8-12mm, indoor, vandal, clear,
white, TDN, TWDR
Illustra Flex 8MP Mini-dome, 3.4-9mm, indoor, vandal, clear,
white, TDN, TWDR
1 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Figure 3 Physical dimensions of the Illustra Flex Indoor Dome camera
Figure 4 Pictorial index of the camera
8200-1456-02 J0 2
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Table 5 Pictorial index descriptions
Index number Description
1 Camera bottom case
2 Tilt adjustment bracket
3 Loosen the screw to take off camera housing
4 Camera housing
5 Dome cover
Figure 6 Pin definitions of the unit
3 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Table 7 Interior button descriptions
Interior button Description
Resets to factory default by pressing and holding the button for five seconds.
Reboots the unit.
Analog out port.
Power over Ethernet (PoE) port.
Figure 8 Connectors of the camera
NOTE
Connectors and field wiring terminals for external Class 2 circuits provided with marking indicating
minimum Class of wiring to be used. Class 2 shall be marked adjacent to the field wiring terminals.
8200-1456-02 J0 4
Installation
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Figure 9 Audio and alarm pin definitions
In the box
Check everything in the packing box matches to the order form and the packing slip. In addition to
this guide, items below are included in the packing box:
• 1 Network Illustra Flex Indoor Dome Camera
• 1 printed Quick Start Guide
• 1 printed Regulatory document
• 1 NTSC/PAL output female BNC cable
• 1 adapter plate (for pendant cap)
• 3 7mm adapter plate screws
• 1 Torx 10 Security L-Key
• 3 18mm plastic anchors and screws
• 1 installation template sticker
• 2 8mm pendant cap screws
• 1 Molded Cap
Contact your dealer if any item is missing.
Note:The adapter plate is for an installation with a ADCi6DPCAPI (W/B) pendant cap and can also
be used to mount to a standard dual gang electrical box.
Installation tools
The following tools assist with installation:
• a drill
• screwdrivers
• wire cutters
5 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Checking appearance
When first unboxing, check whether if there is any visible damage to the appearance of the unit and
its accessories. The protective materials used for the packaging should be able to protect the unit
from most types of accidents during transportation.
Remove the protective part of the unit when every item is checked in accordance with the list in In
the box on page 5.
Procedure 1 Disassembling the camera
Refer to Figure 10 on page 6 for a pictorial index of disassembling the camera.
Step Action
1 Remove the screws (5) to take off camera housing.
2 Gently remove the camera housing (4) and dome cover (6) and set aside.
Figure 10 Disassembling the camera
- End -
Procedure 2 Connecting the wires
Step Action
This unit supports one of the following options as power supply:
1 AC 24V:
a Connect 24V (～ ) cables to terminals ～ AC 24V
2 PoE:
8200-1456-02 J0 6
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
a Connect the RJ-45 jack to a PoE compatible network device that supplied power
through the Ethernet cable.
3 Insert Audio cable and alarm cable to the unit, and connect the network cable to the RJ-45
terminal of a switch.
Note:The power source needs to be NEC Class 2 or LPS. The PoE connection should be provided
by a UL Listed product and the connections shall be made in accordance with Article 800 of the NEC
or local regulations.
- End -
Procedure 3 Mounting the camera
Step Action
1 Mark holes that correspond to the camera base on the mounting surface
2 Drill holes.
3 Fasten the anchors to the mounting surface with screws.
4 Connect the Safety Wire (fall prevention wire, not supplied) with one end to the ceiling and
the other to the safety-cord screw of the unit.
5 Secure the unit bottom case to the wall or ceiling with tapping screws.
6 Adjust the viewing angle. Refer to Adjusting the Position on page 7 for information regarding
WARNING
CAUTION
Procedure 4 Adjusting the Position
The unit has three axes for positioning, refer to Figure 11 on page 8. While monitoring, adjust the
position as below:
Step Action
1 Pan Adjustment (A). For Wall Mount and Tilted Ceilings
2 Horizontal Rotation (B)
how to adjust the viewing angle.
Depending on the material of your mounting surface, you may require different screws and
anchors than those as supplied. To prevent the unit from falling off, ensure that it is secured to a
firm place (ceiling slab or channel) with a safety wire (not supplied) strong enough to sustain the
total weight of the unit. Pay attention to the finishing at the end of the wire. Never turn the lens
more than 360°, which should disconnect or break internal cables.
Safety wire must be connected with one end to the ceiling and the other to the safety-cord screw of
the unit.
- End -
a Rotate the lens base (maximum 375°) until you are satisfied with the field of view.
a Rotate 3D assembly in the base. Do not turn assembly more than 360° as this
assembly may cause the internal cables to twist and disconnect or break.
3 Tilt Adjustment (C):
a Tilt the lens base (maximum 90°) until you are satisfied with the field of view.
7 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Limitation for three axes position:
CAUTION
• Pan range: 375°
• Tilt range: 90°
• Rotate range: Motorize Lens 356°
Figure 11 Adjusting the position of the camera
- End -
Procedure 5 Locking the Camera
Step Action
1 Use a soft, lint-free cloth to wipe the dome cover and remove fingerprints.
2 Attach the inner liner and camera housing.
3 Turn the power on after you have install the unit.
- End -
8200-1456-02 J0 8
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Procedure 6 Installing the molded cap on the camera bottom case
The molded cap is only applicable in installations that don’t need the gap for cables.
Step Action
1 Install the molded cap (1) on the camera bottom case and ensure that it is securely attached.
Figure 12
- End -
9 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Illustra Flex Series 3MP and 8MP Outdoor Dome
Camera
This chapter provides product features, installation procedures, and connection information regarding
the Illustra Flex Series Outdoor Dome cameras.
Product features
Len cases require special care when handling and cleaning to avoid scratches. For information on
bubble handling and cleaning, see 8200-1174-01 Bubble Clearing Procedure Application Note.
Go to https://illustracameras.com/products.
From the Products page, select your camera product range and then select your camera model. Click
Downloads and search for Bubble Handling and Cleaning Procedure.
Product overview
This chapter explains the features and installation of the Illustra Flex Outdoor Dome camera. Product
code and description of the camera is provided in the table below.
Product
Code
IFS03D1OCWIT
IFS08D2OCWIT
Figure 14 Physical dimensions of the Illustra Flex Outdoor Dome camera (mm)
Table 13 Product code and description of the Illustra Flex Outdoor camera
Model Name Description
Illustra Flex 3MP Outdoor
Mini-Dome
Illustra Flex 4K Outdoor
Mini-Dome
Illustra Flex 3MP Mini-dome, 2.8-12mm, outdoor, vandal, clear,
white, TDN w/IR, TWDR
Illustra Flex 8MP Mini-dome, 3.4-9mm, outdoor, vandal, clear,
white, TDN w/IR, TWDR
10 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Figure 15 Physical dimensions of the Illustra Flex Outdoor Dome camera
Figure 16 Pictorial index of the Illustra Flex Outdoor Dome camera
8200-1456-02 J0 11
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Table 17 Pictorial index descriptions
Index number Description
1 Camera bottom case
2 IR board
3 Tilt adjustment bracket
4 Camera top case
5 Loosen the screw to take off camera housing
6 Dome cover
Figure 18 Pin definitions of the unit
12 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Table 19 Interior button descriptions
Interior button Description
Resets to factory default by pressing and holding the button for five seconds.
Reboots the unit.
Analog out port.
Power over Ethernet (PoE) port.
Note:The connector cable of the Outdoor Dome Camera should be contained in a conduit suitable for
outdoor use.
NOTE
Figure 20 Connectors of the unit
Connectors and field wiring terminals for external Class 2 circuits provided with marking indicating
minimum Class of wiring to be used. Class 2 shall be marked adjacent to the field wiring terminals.
8200-1456-02 J0 13
Installation
In the box
Check everything in the packing box matches to the order form and the packing slip. In addition to
this guide, items below are included in the packing box.
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Figure 21 Audio and alarm pin definitions
• 1 Network Illustra Flex Outdoor Dome Camera
• 1 printed Quick Start Guide
• 1 printed Regulatory document
• 1 NTSC/PAL output female BNC cable
• 1 adapter plate (for pendant cap)
• 3 7mm adapter plate screws
• Desiccant
• 1 Torx 10 Security L-Key
• 3 18mm plastic anchors and screws
• 1 installation template sticker
• 2 8mm pendant cap screws
• 1 Molded Cap
Contact your dealer if any item is missing.
Note:The adapter plate is for an installation with a ADCi6DPCAPI (W/B) pendant cap and can also
be used to mount to a standard dual gang electrical box.
Installation tools
The following tools assist with installation:
• a drill
• screwdrivers
• wire cutters
14 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Checking appearance
When first unboxing, check whether if there is any visible damage to the appearance of the unit and
its accessories. The protective materials used for the packaging should be able to protect the unit
from most types of accidents during transportation.
Remove the protective part of the unit when every item is checked in accordance with the list in In
the box on page 14.
Procedure 7 Disassembling the Camera
Step Action
1 Remove the screws (4).
2 Gently remove the camera housing (3) and dome cover (5).
3 Set the camera housing aside.
Figure 22 Disassembling the outdoor camera
- End -
Procedure 8 Connecting the wires
Connect the power cable to the power plugs with one of the following options:
Step Action
1 AC 24V:
a Insert the power cable for AC 24V.
b Connect 24 V (~) cables to terminals ~AC 24V.
2 PoE:
8200-1456-02 J0 15
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
a Connect the RJ-45 jack to a PoE compatible network device that supplies power
through the Ethernet cable.
Note:The power source needs to be NEC Class 2 or LPS. The PoE connection should be provided
by a UL Listed product and the connections shall be made in accordance with Article 800 of the NEC
or local regulations.
- End -
Procedure 9 Mounting the camera
Step Action
1 Mark holes that correspond to the camera base on the mounting surface
2 Drill holes.
3 Fasten the anchors to the mounting surface with screws.
4 Connect the Safety Wire (fall prevention wire, not supplied) with one end to the ceiling and
the other to the safety-cord screw of the unit.
5 Secure the unit bottom case to the wall or ceiling with tapping screws.
6 Adjust the viewing angle.
WARNING
CAUTION
Procedure 10 Optional - 4S Electrical Junction Box
Step Action
1 Secure the mounting kit (optional) to 4S Electrical box using 2 appropriate screws.
2 Secure the unit case to mounting kit using 2 appropriate screws.
3 Tuck the cables in the 4S Electrical box.
4 Adjust the view angles.
5 Attach the unit housing.
6 Turn the power on after you install the unit.
Depending on the material of your mounting surface, you may require different screws and
anchors than those as supplied. To prevent the unit from falling off, ensure that it is secured to a
firm place (ceiling slab or channel) with a safety wire (not supplied) strong enough to sustain the
total weight of the unit. Pay also attention to the finishing at the end of the wire. Never turn the lens
more than 360°, which should disconnect or break internal cables.
Safety wire must be connected with one end to the ceiling and the other to the safety-cord screw of
the unit.
- End -
16 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Figure 23 Mounting the camera with the junction box
NOTE
Procedure 11 Adjusting the Position
The unit has three axes for positioning, refer to Figure 24 on page 18. While monitoring, adjust the
position as below.
Step Action
CAUTION
The mounting kit called out in Figure 23 on page 17 is not supplied with the unit.
Keeping tilt angle over 25 degrees is recommended when IR-LED light is used. If tilt angel is below 25
degrees from the horizontal, the image would be flashed by the reflection of IR-LED light.
- End -
1 Pan Adjustment (A) For Wall Mount and Tilted Ceilings:
a Rotate the lens base (maximum 375°) until you are satisfied with the field of view.
2 Horizontal Rotation (B):
a Rotate 3D assembly in the base. Do not turn assembly more than 360° as this
assembly may cause the internal cables to twist and disconnect or break.
3 Tilt Adjustment (C):
a Tilt the lens base (maximum 90°) until you are satisfied with the field of view.
Limitation for three axes position:
• Pan range: 375°
• Tilt range: 75°
• Rotate range: Motorize Lens 356°
8200-1456-02 J0 17
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Figure 24 Adjusting the position of the camera
NOTE
For outdoor Dome camera series:
Users can adjust zoom level and focus level using the Illustra Connect Web User
Interface.
- End -
Procedure 12 Locking the Camera
Step Action
1 Use a soft, lint-free cloth to wipe the dome cover and remove fingerprints.
2 Attach the inner liner and camera housing.
3 Turn the power on after you have install the unit.
- End -
Procedure 13 Applying the desiccant
Step Action
1 Remove the papers from the back of the desiccant.
2 Attach to the interior side of the tilt adjuster as seen in the image below.
Figure 25 Location for desiccant application
18 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Procedure 14 Installing the molded cap on the camera bottom case
The molded cap is only applicable in installations that don’t need the gap for cables.
Step Action
1 Install the molded cap (1) on the camera bottom case and ensure that it is securely attached.
Figure 26
- End -
8200-1456-02 J0 19
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
System requirements
The below table lists the minimum requirements to implement and operate Illustra Flex Indoor and
Outdoor Dome cameras.
Table 27 System Requirements
System hardware
CPU Intel Pentium 4 2.4GHz or equivalent
RAM 1 GB or above
Display NVIDIA GeForce 6 Series or ATI Mobility Radeon 9500
System software
Browser Microsoft Internet Explorer 9 or above, Firefox, Safari, Chrome
Unit
Power Supply AC 24V / PoE
Networking
Wired
NOTE All the installation and operations should comply with your local electricity safety rules.
CAUTION
To avoid damage to the unit, never connect more than one type of power supply (PoE IEEE802.3
Ethernet Class 0 or AC24V power plug) at the same time. If using PoE, this camera is to be
connecting only to PoE networks without routing to heterogeneous devices.
10/100BASE-T Ethernet (RJ-45 connector)
NOTE: A switch is required for surveillance on multiple units.
20 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Network Connection
Default IP Address
Since this is a network-based unit, an IP address must be assigned at the very first bootup. The
default IP address of the unit is 192.168.1.168 and sub mask is 255.255.255.0.
However, if you have a DHCP server in your network, the unit obtains an IP address automatically
from the DHCP server so that you do not need to change the IP address of the camera.
Note:If you assign the camera a Static IP address prior to DHCP being enabled, the camera first
reboots for approximately 30 seconds and then remains accessible at its Static IP until it connects to
a DHCP server.
• Connect to a PC directly: Directly connect the camera to a PC using a standard Ethernet
cable. This requires POE switch or injector.
• Connecting a camera to a Local Area Network (LAN): To add the camera to an existing
LAN, connect the camera to the POE hub or switch on your network.
Figure 28 Network connection diagram
Default camera settings
The following table describes the default camera settings.
Network Settings Defaults
DHCP Enabled
Static IPAddress 192.168.1.168
Default Username admin
Default Password admin
Note:At first login the user is prompted to change the default username and password.
21 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Procedure 15 Connecting from a computer
Step Action
1 Ensure the camera and your computer are in the same subnet.
2 Check whether if the network is available between the unit and the computer by pinging the
default IP address.
a Start a command prompt.
b Type “Ping 192.168.1.168”. If the message “Reply from…” appears, it means the con-
nection is available.
3 Start Internet Explorer and enter IP address: 192.168.1.168. A login window appears. In the
window, enter the default user name: admin and password: admin to log in.
- End -
DHCP
On initial camera startup, and after a hardware factory reset, Dynamic Host Configuration Protocol
(DHCP) is enabled by default and remains enabled until the camera receives either a DHCP address
or is assigned a Static IP address.
Procedure 16 Enable DHCP
Step Action
1 Select Setup on the Web User Interface banner to display the setup menus.
2 Select the TCP/IP tab in the Basic Configuration menu.
3 Select the Enable DHCP check box to enable DHCP and disable manual settings.
4 Select Apply to save the settings.
The camera searches for a DHCP server. If one is found it connects to that server. If no connection
is made to a DHCP server within two minutes, the camera goes to the default IP address
192.168.1.168, but continues to search for a DHCP address.
Note:If you assign the camera a Static IP address prior to DHCP being enabled, the camera first
reboots for approximately 30 seconds and then remains accessible at its Static IP until it connects to
a DHCP server.
- End -
Procedure 17 Disable DHCP
Step Action
1 Select Setup on the Web User Interface banner to display the setup menus.
2 Select the TCP/IP tab in the Basic Configuration menu.
3 Clear the Enable DHCP check box to disable DHCP and allow manual settings to be
entered.
The default setting is ‘Enabled’.
4 If Enable DHCP has been disabled:
8200-1456-02 J0 22
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
a Enter the IPv4 Address in the IPv4 Address text box in the form xxx.xxx.xxx.xxx.The
default setting is ‘192.168.1.168’
b Enter the Network Mask in the Network Mask text box xxx.xxx.xxx.xxx. The default
setting is ‘255.255.255.0’
c Enter the Gateway IP address in Gateway text box xxx.xxx.xxx.xxx.
d Enter the Primary DNS Server in the Primary DNS Server text box xxx.xxx.xxx.xxx.
5 Select Apply to save the settings.
- End -
Managing cameras with the Illustra Connect tool
In addition to using the IE browser to access your camera, you can alternatively use the provided
tool, Illustra Connect.
Illustra Connect is a management tool designed to manage your network cameras on the LAN. It can:
• help you find multiple network cameras
• set the IP addresses
• show connection status
• manage firmware upgrades
• bulk configuration
Procedure 18 Connecting to the camera using Illustra Connect
Note:
Illustra Connect can only discover devices on the same subnet as its host computer. Therefore, the
camera and the computer being used to configure it must be on the same subnet.
Step Action
1 Using a computer which is connected to the same network and subnet, install the Illustra
Connect software.
The Illustra Connect software and the Illustra Connect manual are available to download on
www.illustracameras.com
2 When the installation is complete, run Illustra Connect.
It searches the network and displays all compliant devices.
3 Select the camera you want to configure, locating it by its unique MAC address.
4 Right-click the camera and select Launch Web GUI Configuration. The camera Web User
Interface displays.
- End -
23 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Procedure 19 Connecting to the camera using the static IP address
Step Action
1 The camera attempts to obtain an IP Address from the DHCP Server. When no DHCP
Server is available the camera is assigned a Static IP address of 192.168.1.168.
2 Open Microsoft Internet Explorer and enter the URL of the camera as 192.168.1.168. The
camera sign in page displays.
Note:
The computer you use to configure the camera must have an IPaddress on the same subnet.
- End -
Procedure 20 Logging on to the camera web user interface
Step Action
1 When you select the camera, the sign in page displays. Select your preferred language from
the drop-down menu.
2 Enter the username in the Username text box. The default username is admin.
3 Enter the password in the Password text box. The default password is admin.
4 Select Log in.
Note:The first time that you access the camera or after a factory reset the following two pop up
windows are visible: A pop up window that requests the user to Define a Host ID and a pop up
window that requests the user to select a Security Type. Please refer to the user manual for further
information on this.
5 The Live view page is visible. This displays the current view of the camera.
Note:
At first login the user is prompted to change the default username and password.
- End -
Procedure 21 Enabling the correct video orientation for a wall mounted
camera
Step Action
1 Log on to the camera web user interface.
2 Select Setup on the camera web user interface banner to display the setup menus.
3 Select the Picture Basic tab from the Basic Configuration menu.
4 Select the required Orientation setting:
• Mirror
• Flip
5 The video pane updates to display the new settings.
- End -
8200-1456-02 J0 24
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Network Topology
The Illustra Flex cameras deliver video images and audio in real-time using the Internet and Intranet.
It is equipped with an Ethernet RJ-45 network interface.
The following images illustrate the network topologies of the cameras.
Figure 29 Illustra Flex Dome Cameras Network Topology Type I
Figure 30 Illustra Flex Dome Cameras Network Topology Type II
25 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Appendix A: Technical Specifications
The table below lists technical specifications of the Illustra Flex Indoor and Outdoor Dome camera.
General Features
Model Type Indoor Mini-dome camera Outdoor Mini-Dome camera
Model No. IFS03D1ICWTT / IFS08D2ICWTT IFS03D1OCWIT / IFS08D2OCWIT
Camera Body
Color
Vandal
Resistant
Rating
White White
IK10 IK10
Mechanical Features
Dimensions Ø123x107mm Ø123x107mm
Weight approximately 0.7kg approximately 0.7kg
Pan Rotation
Angle
Tilt Angle 90° 75°
Z-axis Rotation 356° 356°
Housing
Material
Bubble Trim
Ring Material
Other Housing
Material
375° 375°
Aluminum Alloy Aluminum Alloy
ADC12 ADC12
PC/KE-951U PC/KE-951U
Video Processor
ROM/Flash Size 256 Mbytes 256 Mbytes
RAM Size 512 Mbytes 512 Mbytes
RTC Hold Up
Time
24 hours 24 hours
Image Sensor
Format 1/2.8" CMOS 1/2.8" CMOS
Capture Method Rolling Rolling
Scan Method Progressive Progressive
Lens
Design Type Varifocal 6 groups 8 elements (1 aspheric glass lens)
Mount Phi 14mm Phi 14mm
26 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Aperture Range F/1.4(W) ~ F/2.7(T) F/1.4(W) ~ F/2.7(T)
Focal Length
Range
Focal Means Motorized Motorized
Focal Type Varifocal Varifocal
Focus Type Motorized Motorized
Auto Focus One-Touch One-Touch
IR Correction N/A Optical corrected
Day/Night True D/N with ICR True D/N with ICR
Horizontal
Angle of View
Vertical Angle
of View
Format 1/2.7" 1/2.7"
2.8-12 mm 2.8-12 mm
98ﾟ (Wide); 35ﾟ (Tele) 98ﾟ (Wide); 35ﾟ (Tele)
71ﾟ (Wide); 26ﾟ (Tele) 71ﾟ (Wide); 26ﾟ (Tele)
Illuminator
Wavelength N/A 850 mm
IR Distance N/A 25m
Smart IR N/A
Yes. When Smart IR is ON, AE luma target will be
reduced slightly and applies some dWDR.
Adaptive IR N/A
Number of IR
LED devices
N/A 16PCS
Yes. Adaptive IR refers to lens position to adjust
the IR intensity of both narrow and broad IR LEDs
to have better exposure balance.
Power Supply
Power
Requirement
Current Draw
Amps
Wattage 5.9W 11.9W
Line Frequency
Range
AC 24V, PoE IEEE 802.3af class 3 AC 24V, PoE IEEE 802.3af class 3
0.338mA 0.688mA
47 to 63 Hz 47 to 63 Hz
Video Codecs
Frame Rate
Range
Maximum
Resolution and
Rate
Maximum
Resolution and
1 to 60 fps 1 to 60 fps
IFS03D1ICWTT - 2048x1536 @ 30 fps IFS03D1OCWIT - 2048x1536 @ 30 fps
IFS08D2ICWTT- 3840x2160 @ 15 fps IFS08D2OCWIT - 3840x2160 @ 15 fps
8200-1456-02 J0 27
Rate
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Video Imaging
Dynamic Range
Method
3MP includes WDR, TrueWDR,
TWRD3x
8MP does not include TWDR3x
3MP includes WDR, TrueWDR, TWRD3x
8MP does not include TWDR3x
Audio
Sampling Bits 16-BIT 16-BIT
Input Type SE/Line/MIC SE/Line/MIC
Input
Impedance
Maximum Input
Level
Input connector Terminal Block Terminal Block
Output Type
Impedance
Maximum
Output
20K/Attenuation = 0 dB 20K/Attenuation = 0 dB
2Vp-p 2Vp-p
Hi impedance Hi impedance
2Vp-p 2Vp-p
I/O Interfaces
Micro SD Card
Alarm Inputs 1 1
Micro SD/SDXC slot up to 128GB,
Class 10 or higher. Card not included.
Micro SD/SDXC slot up to 128GB, Class 10 or
higher. Card not included.
Auxiliary
Outputs
Video Output Yes Yes
IP Connector RJ-45 RJ-45
LED Indicators Network, Green LED, Orange LED Network, Green LED, Orange LED
Reset Buttons Reboot and Return to Defaults Reboot and Return to Defaults
1 1
Environmental
Operating
Temperature
Range
Start-up
Temperature
Range
Water/Dust
Intrusion
-20° ~+50°C -50° ~ +50°C
-20° ~+50°C -40° ~ +50°C
N/A IP66/67
Client Interfaces
Browsers
supported
IE 9 or above, Firefox,Safari, Chrome IE 9 or above, Firefox,Safari, Chrome
28 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Networking
English (default), Arabic, Czech,
Languages
supported
Ethernet 10/100Base-T 10/100Base-T
Supported
Protocols
Base Protocol TCP/IP - RFC4614 TCP/IP - RFC4614
Internet Layer
Addressing
Transport Layer
Data
Transmission
Network
Address
Configuration
Danish, German, Spanish, French,
Hungarian, Italian, Korean, Japanese,
Netherlands, Polish, Portuguese,
Swedish, Turkish, Chinese Traditional,
Chinese Simplified, Russian.
TCP/IP, IPv4, IPv6, TCP, UDP, HTTP,
FTP, DHCP, WS-Discovery, DNS,
DDNS, RTP, TLS, Unicast, Multicast,
NTP, SMTP, WSSecurity, IEEE 802.1x,
PEAP, SSH, HTTPS, SSL, SOAP,
WSAddressing, CIFS, SNMP, UPnP,
RTSP, LLDP
IPv4 - RFC791
IPv6 - RFC2460
TCP - RFC973
UDP - RFC768
HTTP/HTTPS - RFC2616
FTP - RFC959
SFTP
DHCP - RFC2131 Zeroconf RFC3927 Static IP address
LLDP
English (default), Arabic, Czech, Danish, German,
Spanish, French, Hungarian, Italian, Korean,
Japanese, Netherlands, Polish, Portuguese,
Swedish, Turkish, Chinese Traditional, Chinese
Simplified, Russian
TCP/IP, IPv4, IPv6, TCP, UDP, HTTP, FTP, DHCP,
WS-Discovery, DNS, DDNS, RTP, TLS, Unicast,
Multicast, NTP, SMTP, WSSecurity, IEEE 802.1x,
PEAP, SSH, HTTPS, SSL, SOAP, WSAddressing,
CIFS, SNMP, UPnP, RTSP, LLDP
IPv4 - RFC791
IPv6 - RFC2460
TCP - RFC973
UDP - RFC768
HTTP/HTTPS - RFC2616
FTP - RFC959
SFTP
DHCP - RFC2131 Zeroconf - RFC3927 Static IP
address
LLDP
Time
Synchronization
E-mail
Authentication
and Security
Streaming
Firmware
Upgrade
NTP - RFC1305
IETF NTP Working Group
i minute poll rate
SMTP - RFC5321
Authenticated SMTP - RFC4954
IEEE.802.1x - TLS/PEAP
HTTPS (HTTP over TLS) - RFC2818
WS-Security
Multi-level password protection
IP address filtering
HTTPS encryption
User access log
RTP - RFC3550
RTSP - RFC2326
Unicast Streaming
Multicast RFC 1112 level 1
Browser/illustra Connect/ONVIF Browser/illustra Connect/ONVIF
NTP - RFC1305
IETF NTP Working Group
i minute poll rate
SMTP - RFC5321
Authenticated SMTP - RFC4954
IEEE.802.1x - TLS/PEAP
HTTPS (HTTP over TLS) - RFC2818
WS-Security
Multi-level password protection
IP address filtering
HTTPS encryption
User access log
RTP - RFC3550
RTSP - RFC2326
Unicast Streaming
Multicast RFC 1112 level 1
8200-1456-02 J0 29
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Appendix B: Stream Resolutions
Flex Gen 2 3MP and Flex 8MP Streaming Combinations
Table 31 on page 30 and Table 32 on page 31 provide information for the stream resolutions and
supported FPS of the Flex Gen 2 3MP cameras herein. Table 33 on page 32 provides information for
the stream resolutions and supported FPS of the Flex 8MP cameras.
Table 31 Flex 3MP Stream Set A (all resolution, codes and frame rate combinations of Stream 1, 2
and 3 are valid)
Stream
Resolution
Stream 1 Stream 2
2048x1536
1920x1080
1664x936
1280x720
Codecs
H264/H264
IntelliZip
H265/H26
IntelliZip
H264/H264
IntelliZip
H265/H26
IntelliZip
MJPEG
H264/H264
IntelliZip
H265/H26
IntelliZip
MJPEG
H264/H264
IntelliZip
H265/H26
IntelliZip
MJPEG
Frame
Rates (fp s)
1-30 1280x720
1-30 1024x576
1-30 640x360
1-30 480x360
Stream
Resolution
Codecs
H264/H264
IntelliZip
H265/H26
IntelliZip
MJPEG
H264/H264
IntelliZip
H265/H26
IntelliZip
MJPEG
H264/H264
IntelliZip
H265/H26
IntelliZip
MJPEG
H264/H264
IntelliZip
H265/H26
IntelliZip
MJPEG
Frame
Rates (fp s)
1-30 640x360 MJPEG 7-15
1-30 480x360 MJPEG 7-15
1-30 384x288 MJPEG 7-15
1-30
Stream
Resolution Cod ecs
Stream
3
Frame
Rates (fp s)
TWDR
Support
Yes
(2x)
Yes
(2x)
Yes
(2x)
Yes
(2x)
H264/H264
IntelliZip
384x288
H265/H26
IntelliZip
MJPEG
1-30
Yes
(2x)
30 8200-1456-02 J0
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Table 32 Flex 3MP Stream Set B (all resolution, codes and frame rate combinations of Stream 1, 2
and 3 are valid)
Stream
Codecs
Resolution
Frame
Rates
(fps)
Stream
Resolution
Stream 1 Stream 2
H264/H264
IntelliZip
1920x1080
H265/H26
31-60 1280x720
IntelliZip
MJPEG
H264/H264
IntelliZip
1664x936
H265/H26
31-60 1024x576
IntelliZip
MJPEG
H264/H264
IntelliZip
1280x720
H265/H26
31-60 640x360
IntelliZip
MJPEG
480x360
Codecs
H264/H264
IntelliZip
H265/H26
IntelliZip
MJPEG
H264/H264
IntelliZip
H265/H26
IntelliZip
MJPEG
H264/H264
IntelliZip
H265/H26
IntelliZip
MJPEG
H264/H264
IntelliZip
H265/H26
IntelliZip
MJPEG
Frame
Rates
(fps)
Stream
Resolution Codecs
Frame
Rates
(fps)
Support
Stream
3
1-15 640x360 MJPEG 7-15 No
1-15 480x360 MJPEG 7-15 No
1-15 384x288 MJPEG 7-15 No
1-15 No
TWDR
H264/H264
IntelliZip
384x288
H265/H26
1-15 No
IntelliZip
MJPEG
Note:A maximum of 5 concurrent streams are supported by the camera. This includes shared
streams. So, for example, Stream 1 can be shared twice along with a running Stream 2 and Stream 3,
or Stream 1 can be shared 4 times if Stream 2 and Stream 3 are not running.
Note:When frame-rate is more than 30fps the following restrictions apply:
• Stream 1 max resolution is 1920x1080.
• TWDR is disabled.
• Stream 2 has a maximum frame-rate of 15.
8200-1456-02 J0 31
Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide
Table 33 Flex 8MP Indoor and Outdoor Dome Camera resolutions
Flex 8MP Indoor and Outdoor Dome camera resolutions
Stream 1 FPS Stream 2 FPS Stream 3 FPS
(3840x2160) 4K 16:9
(3264x1840) 16:9
1-15
(2592x1944) 4:3 (640x360) nHD 16:9 (384x288) 4:3
(2688x1520) 16:9 (480x360) 480 4:3
(2048x1536) QXGA 4:3 (384x288) 4:3
(1920x1080) 1080p
16:9
(1280x960) SXGA 16:9
(1280X720) 720p 16:9
1-60
(1280x720) 720p
(1024x576) PAL+
16:9
1-15 or 130
(640x360) nHD
16:9
(480x360) 480 4:3
Note:Stream 2 is limited to a maximum of 15 FPS when: Stream 1 is set to 2048x1536 or above.
Stream 1 is set to 1920x1080 or above with FPS greater that 30.
Note:Stream 2 automatically reconfigures to a maximum of 15 FPS if Stream 1 FPS is 30 or greater.
Note:Stream 2 supports 1-30 FPS when Stream 1 is set to 1920x1080 or below with FPS set to a
maximum of 30.
7-15
Note:Codec MJPEG is not supported when the resolution is equal to or greater than 2048x1536.
Note:TrueWDR 2x. When TrueWDR2x is switch on, the following limits apply: For 2048x1536 and
above, the framerate is limited to 15FPS (as it is when TrueWDR is off). For 1920x1080 and below,
the framerate is limited to 30FPS.
Note:TrueWDR 3x is not available on 8MP units.
32 8200-1456-02 J0
Loading...