American Dynamics IFS08D2OCWIT, IFS08D2ICWTT, IFS03D1OCWIT, IFS03D1ICWTT User Manual

Illustra Flex Series 3MP and 8MP Indoor and Outdoor

Dome Cameras

Quick Start Guide

Notice

Please read this manual thoroughly and save it for future use before attempting to connect or operate this unit.

The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice.

Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine-readable form, in whole or in part, without prior written consent of Tyco Security Products.

Tyco Security Products

6600 Congress Avenue

Boca Raton, FL 33487 U.S.A.

Customer Service

Thank you for using American Dynamics products. We support our products through an extensive worldwide network of dealers. The dealer through whom you originally purchased this product is your point of contact if you need service or support. Our dealers are empowered to provide the very best in customer service and support. Dealers should contact American Dynamics at (800) 507-6268 or (561) 912-6259 or on the Web at www.americandynamics.net.

Trademarks

The trademarks, logos, and service marks displayed on this document are registered in the United States [or other countries]. Any misuse of the trademarks is strictly prohibited and Tyco Security Products will aggressively enforce its intellectual property rights to the fullest extent of the law, including pursuit of criminal prosecution wherever necessary. All trademarks not owned by Tyco Security Products are the property of their respective owners, and are used with permission or allowed under applicable laws.

Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all features. Availability varies by region; contact your sales representative.

Table of Contents

Illustra Flex Series 3MP and 8MP Indoor Dome Camera 1

Product features 1

Product overview 1

Installation 5

Illustra Flex Series 3MP and 8MP Outdoor Dome Camera 10

Product features 10

Product overview 10

Installation 14

System requirements 20

Network Connection 21

Default IP Addr ess 21

DHCP 22

Managing cameras with the Illustra Connect tool 23

Network Topology 25

Appendix A: Technical Specifications 26

Appendix B: Stream Resolutions 30

Warning

• These units operate at AC 24V/ PoE.

• Installation and service should be performed only by qualified and experienced technicians and comply with all local codes and rules to maintain your warranty.

• To reduce the risk of fire or electric shock, do not expose the product to rain or moisture.

• Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral detergent and wipe with a dry soft cloth.

• Do not apply benzene or thinner to the camera, which may cause the surface of the unit to be melted or lens to be fogged.

• Avoid aligning the lens to very bright objects (for example, light fixtures) for long periods of time.

• ITE is to be connected only to PoE networks without routing to the outside plant.

• The power supply shall be approved for ITE NEC Class 2 or LPS with a rating of 24VAC, 550mA minimum and 50 degrees Celsius.

• Video Out connection should be intra-building only.

• Avoid operating or storing the unit in the following locations:

• Extremely humid, dusty, or hot/cold environments. Recommended operating temperature is:

• Indoor Minidome: -20˚C to 50˚C (-4˚F to 122˚F)

• Outdoor Minidome: -50˚C to 50˚C (-58˚F to 122˚F)

• Power over Ethernet (PoE) does not support heater.

• Near sources of powerful radio or TV transmitters.

• Near fluorescent lamps or objects with reflections.

• Under unstable or flickering light sources.

WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the European Union and other European countries with separate collection systems). This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures.

Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide

Illustra Flex Series 3MP and 8MP Indoor Dome

Camera

This chapter provides product features, installation procedures, and connection information regarding the Illustra Flex Series Indoor Dome cameras.

Product features

Len cases require special care when handling and cleaning to avoid scratches. For information on bubble handling and cleaning, see 8200-1174-01 Bubble Clearing Procedure Application Note.

Go to https://illustracameras.com/products.

From the Products page, select your camera product range and then select your camera model. Click

Downloads and search for Bubble Handling and Cleaning Procedure.

Product overview

This chapter explains the features and installation of the Illustra Flex Indoor Dome cameras. Product code and description of the camera is provided in the table below.

Table 1 Product code and description of the Illustra Flex Indoor Dome camera

Product

Code

IFS03D1ICWTT

IFS08D2ICWTT

Figure 2 Physical dimensions of the Illustra Flex Indoor Dome camera (mm)

Model Name Description

Illustra Flex 3MP Indoor Mini-Dome

Illustra Flex 4K Indoor Mini-Dome

Illustra Flex 3MP Mini-dome, 2.8-12mm, indoor, vandal, clear, white, TDN, TWDR

Illustra Flex 8MP Mini-dome, 3.4-9mm, indoor, vandal, clear, white, TDN, TWDR

1 8200-1456-02 J0

Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide

Figure 3 Physical dimensions of the Illustra Flex Indoor Dome camera

Figure 4 Pictorial index of the camera

8200-1456-02 J0 2

Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide

Table 5 Pictorial index descriptions

Index number Description

1 Camera bottom case

2 Tilt adjustment bracket

3 Loosen the screw to take off camera housing

4 Camera housing

5 Dome cover

Figure 6 Pin definitions of the unit

3 8200-1456-02 J0

Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide

Table 7 Interior button descriptions

Interior button Description

Resets to factory default by pressing and holding the button for five seconds.

Reboots the unit.

Analog out port.

Power over Ethernet (PoE) port.

Figure 8 Connectors of the camera

NOTE

Connectors and field wiring terminals for external Class 2 circuits provided with marking indicating minimum Class of wiring to be used. Class 2 shall be marked adjacent to the field wiring terminals.

8200-1456-02 J0 4

Installation

Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide

Figure 9 Audio and alarm pin definitions

In the box

Check everything in the packing box matches to the order form and the packing slip. In addition to this guide, items below are included in the packing box:

• 1 Network Illustra Flex Indoor Dome Camera

• 1 printed Quick Start Guide

• 1 printed Regulatory document

• 1 NTSC/PAL output female BNC cable

• 1 adapter plate (for pendant cap)

• 3 7mm adapter plate screws

• 1 Torx 10 Security L-Key

• 3 18mm plastic anchors and screws

• 1 installation template sticker

• 2 8mm pendant cap screws

• 1 Molded Cap

Contact your dealer if any item is missing.

Note:The adapter plate is for an installation with a ADCi6DPCAPI (W/B) pendant cap and can also be used to mount to a standard dual gang electrical box.

Installation tools

The following tools assist with installation:

• a drill

• screwdrivers

• wire cutters

5 8200-1456-02 J0

Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide

Checking appearance

When first unboxing, check whether if there is any visible damage to the appearance of the unit and its accessories. The protective materials used for the packaging should be able to protect the unit from most types of accidents during transportation.

Remove the protective part of the unit when every item is checked in accordance with the list in In the box on page 5.

Procedure 1 Disassembling the camera

Refer to Figure 10 on page 6 for a pictorial index of disassembling the camera.

Step Action

1 Remove the screws (5) to take off camera housing.

2 Gently remove the camera housing (4) and dome cover (6) and set aside.

Figure 10 Disassembling the camera

- End -

Procedure 2 Connecting the wires

Step Action

This unit supports one of the following options as power supply:

1 AC 24V:

a Connect 24V (～ ) cables to terminals ～ AC 24V

2 PoE:

8200-1456-02 J0 6

Illustra Flex 3MP and 8MP Indoor and Outdoor Dome Cameras Quick Start Guide

a Connect the RJ-45 jack to a PoE compatible network device that supplied power

through the Ethernet cable.

3 Insert Audio cable and alarm cable to the unit, and connect the network cable to the RJ-45

terminal of a switch.

Note:The power source needs to be NEC Class 2 or LPS. The PoE connection should be provided by a UL Listed product and the connections shall be made in accordance with Article 800 of the NEC or local regulations.

- End -

Procedure 3 Mounting the camera

Step Action

1 Mark holes that correspond to the camera base on the mounting surface

2 Drill holes.

3 Fasten the anchors to the mounting surface with screws.

4 Connect the Safety Wire (fall prevention wire, not supplied) with one end to the ceiling and

the other to the safety-cord screw of the unit.

5 Secure the unit bottom case to the wall or ceiling with tapping screws.

6 Adjust the viewing angle. Refer to Adjusting the Position on page 7 for information regarding

WARNING

CAUTION

Procedure 4 Adjusting the Position

The unit has three axes for positioning, refer to Figure 11 on page 8. While monitoring, adjust the position as below:

Step Action

1 Pan Adjustment (A). For Wall Mount and Tilted Ceilings

2 Horizontal Rotation (B)

how to adjust the viewing angle.

Depending on the material of your mounting surface, you may require different screws and anchors than those as supplied. To prevent the unit from falling off, ensure that it is secured to a firm place (ceiling slab or channel) with a safety wire (not supplied) strong enough to sustain the total weight of the unit. Pay attention to the finishing at the end of the wire. Never turn the lens more than 360°, which should disconnect or break internal cables.

Safety wire must be connected with one end to the ceiling and the other to the safety-cord screw of the unit.

- End -

a Rotate the lens base (maximum 375°) until you are satisfied with the field of view.

a Rotate 3D assembly in the base. Do not turn assembly more than 360° as this

assembly may cause the internal cables to twist and disconnect or break.

3 Tilt Adjustment (C):

a Tilt the lens base (maximum 90°) until you are satisfied with the field of view.

7 8200-1456-02 J0

+ 25 hidden pages