Page 1
IR PTZ CEILING MOUNT
INSTALLATION GUIDE
8200-1793-01 B0
1 of 5
©2019 Tyco Security Products. All rights
reserved.
IFIRPTZC2X2 Ceiling Mount
Installation Guide
The IFIRPTZC2X2 ceiling mount is used to mount the
IR PTZ camera in a 2x2 suspended ceiling.
This guide explains how to assemble and install this
mounting structure.
Parts Supplied with IFIRPTZC2X2 Part Number
Plate 2x2 Mount 0505-2574-01
Galvanized Wire Hanger 2898-0007-01
T Bar Ceiling Kit 0351-1673-01
IR PTZ 2x2 Install Kit 0352-0642-01
Parts Supplied with IFIRPTZWRECMT
Rubber Inserts x4
Mylar x2
Security Torx Wrench x1
Procedure 1: Installing the Ceiling Mount
Note: If placing the ceiling mount into a 2 x 2 foot opening,
use the T Bar ceiling Kit. See instructions supplied with the kit.
Note: Steps 1 to 7 below refer to Figure 1.
Step Action
1. Remove the ceiling tile to create an
remove adjacent tiles on both sides of the opening to
facilitate access to cables.
2. Thread the four hanging wires around
nearest the four corners of the opening such as red
iron or I-beams.
Note: Do not attach to pipes or conduit.
3. Twist
each wire around itself at least four times to
secure it to the roof structure.
4. Remove the four turnbuckles from the kit and fully
extend the hook and eye of each one.
5. Insert the hook of the turnbuckle into each of the four
holes on the mounting plate and using a pliers, crimp
the hook to affix the turnbuckle to the plate.
6. Tilt the mounting plate to get it above the
then drop it in place.
7. Straighten each hanging wire, then thread
the eye of the turnbuckle closest to it and twist it
around itself at least four times.
Figure 1.
opening and
a roof structure
opening,
it through
Page 2
IR PTZ CEILING MOUNT
INSTALLATION GUIDE
8200-1793-01 B0
2 of 5
Procedure 2: Recess mount installation with
Procedure 2: Recess mount installation
a ceiling plate.
Step Action
1. Secure the adaptor ring to the recess
mount bracket (IFIRPTZWRECMT).
See Figure 2a.
Figure 2a
2. Place the 310mm (12.2inch) ‘Guide’ sticker
provided in the accessory kit on the ceiling
plate and cut a 310mm hole, then insert
the recess mount bracket into the ceiling
plate hole. See Figure 2b.
Figure 2b
3. Turn both ‘’locking’’ screws clockwise to
fully extend the ‘’swing out’’ mounting
clips and seat them tightly against the top
surface of the ceiling plate.
See Figure 2c.
with a ceiling plate (continued).
Step Action
4. Attach the PTZ camera safety wire to the
‘J’ hook on the recess mount bracket and
connect the cables to the PTZ camera.
See Figure 2d.
Figure 2d
5. Turn the PTZ camera clockwise to
securely connect the camera to the
adaptor ring. See Figure 2d.
6. Remove the protective paper from the
four rubber inserts and using the
adhesive side stick them into the four
gaps between the camera outer
enclosure and the recess mount bracket.
See Figure 2e.
Figure 2c
Figure 2e
Page 3
IR PTZ CEILING MOUNT
INSTALLATION GUIDE
8200-1793-01 B0
3 of 5
Procedure 2: Recess mount installation with
Procedure 3: Recess mount installation
a ceiling plate (continued).
Step Action
7. Place the ceiling cover around the PTZ
camera. See Figure 2f.
Figure 2f
8. Turn the two screws clockwise to lock the
ceiling cover to the recess mounting
bracket. See Figure 2g.
with a 2x2 ceiling plate.
Step Action
1. Secure the adaptor ring to the recess
mount bracket (IFIRPTZWRECMT).
See Figure 3a.
Figure 3a
2. Insert the recess mount bracket into the
2x2 ceiling plate (IFIRPTZC2X2) hole.
See Figure 3b.
9. Attached the two ‘mylars’ to conceal both
Figure 2g
screws. See Figure 2h.
Figure 2h
Figure 3b
3. Turn both ‘’locking’’ screws clockwise to
fully extend the ‘’swing out’’ mounting
clips and seat them tightly against the top
surface of the 2x2 ceiling plate. See
Figure 3c.
Figure 3c
Page 4
IR PTZ CEILING MOUNT
INSTALLATION GUIDE
8200-1793-01 B0
4 of 5
Procedure 3: Recess mount installation with
Procedure 3: Recess mount installation
a 2x2 ceiling plate (continued).
Step Action
4. Attach the PTZ camera safety wire to the ‘J’
hook on the recess mount bracket and
connect the cables to the PTZ camera.
See Figure 3d.
Figure 3d
5. Turn the PTZ camera clockwise to securely
connect the camera to the adaptor ring.
See Figure 3d.
6. Remove the protective paper from the four
rubber inserts and using the adhesive side
stick them into the four gaps between the
camera outer enclosure and the recess
mount bracket. See Figure 3e.
with a 2x2 ceiling plate (continued).
Step Action
7. Place the ceiling cover around the PTZ
camera. See Figure 3f.
Figure 3f
8. Turn the two screws clockwise to lock the
ceiling cover to the recess mounting
bracket. See Figure 3g.
Figure 3g
9. Attached the two ‘mylars’ to conceal both
screws. See Figure 3h.
Figure 3e
Figure 3h
Page 5
IR PTZ CEILING MOUNT
INSTALLATION GUIDE
8200-1793-01 B0
5 of 5
www.americandynamics.net
Declarations
Thank you for using American Dynamics products. We
support our products through an extensive and worldwide
network of dealers. The dealer, through whom you
originally purchased this product, is your point of contact
if you have a need for service or support. Our dealers are
fully empowered to provide the very best in customer
service and support.
Dealers should contact American Dynamics at (800) 5076268 or (561) 912-6259 or on the web at
www.americandynamics.net.
WARRANTY DISCLAIMER: Sensormatic Electronics
Corporation makes no representation or warranty with
respect to the contents hereof and specifically disclaims
any implied warranties of merchantability or fitness for
any particular purpose.
NOTICE: The information in this manual was current when
published. The manufacturer reserves the right to revise
and improve its products. All specifications are therefore
subject to change without notice.
LIMITED RIGHTS NOTICE: For units of the Department of
Defense, all documentation and manuals were developed
at private expense and no part of it was developed using
Government Funds. The restrictions governing the use and
disclosure of technical data marked with this legend are set
forth in the definition of “limited rights” in paragraph (a)
(15) of the clause of DFARS 252.227.7013. Unpublished rights reserved under the Copyright Laws of the United
States.
TRADEMARK NOTICE: The trademarks, logos, and service
marks displayed on this document are registered in the
United States [or other countries]. Any misuse of the
trademarks is strictly prohibited and Tyco International Ltd.
will aggressively enforce its intellectual property rights to
the fullest extent of the law, including pursuit of criminal
prosecution wherever necessary. All trademarks not owned
by Tyco International Ltd. are the property of their
respective owners, and are used with permission or
allowed under applicable laws.
Product offerings and specifications are subject to change
without notice. Actual products may vary from photos. Not
all products include all features. Availability varies by
region; contact your sales representative.
COPYRIGHT: Under copyright laws, the contents of this
manual may not be copied, photocopied, reproduced,
translated or reduced to any electronic medium or
machine- readable form, in whole or in part, without prior
written consent of ©2019 Tyco Security Products. All
rights reserved.
American Dynamics 6600 Congress Avenue
Boca Raton, FL 33487 U.S.A.
Loading...