American Dynamics ADNSNVR-CL1 User Manual
PART 1 – GENERAL
The intent of this document is to specify the minimum criteria for the design,
supply, installation, and commissioning of the Network Video Recorder.
1.01 SUMMARY
A. The Network Video Recorder shall be turn-key, software-based open platform
solution that functions as an appliance server and operates on hardened and
embedded Linux
bundled server solution.
1.02 REFERENCES
A. Bureau of Standards, Metrology and Inspection (BSMI)
B. Canadian Standards Association (CSA)
C. China Compulsory Certificate (CCC)
D. Conformity for Europe (CE)
E. EMC and Radio Communications Compliance (C-Tick)
F. Federal Communications Commission (FCC)
G. HyperText Transfer Protocol (HTTP)
H. Interference-Causing Equipment Standards (ICES)
I. International Electrotechnical Commission (IEC)
J. Ministry of Information & Communications (MIC)
K. South African Bureau of Standards (SABS)
L. Transmission Control Protocol/Internet Protocol (TCP/IP)
M. Underwriters Laboratories Inc. (UL)
N. Voluntary Control Council for Interference (VCCI)
1.03 DEFINITIONS
A. No Substitutes: The exact make and model number identified in this
specification shall be provided without exception.
B. Or Equal: Any item may be substituted for the specified item provided that in
every technical sense, the substituted item provides the same or better capability
and functionality.
C. Or Approved Equal: A substitute for the specified item may be offered for
approval by the Owner. The proposed substitution must, in every technical sense,
provide the same or better capability and functionality as the specified item. Such
requests for approval shall be submitted in accordance with the provisions of
VideoEdge®
Network Video Recorder
®
operating system. It shall be available as software-only or as a
8200-2608-01 B0 VideoEdge
®
Network Video Recorder 1 of 20
Architect & Engineer Specification
V
PART 1.05 – SUBMITTALS, and must be obtained within the time frames
outlined.
IDEOEDGE
1.04 SYSTEM DESCRIPTION
A. The Network Video Recorder shall be turn-key, software-based open platform
solution that functions as an appliance server and operates on hardened and
embedded Linux® operating system. It shall be available as software-only or as
a bundled server solution. The unit shall combine multiplexing, sensor/motion
detection, video, and audio. The unit must operate in server-client architecture as
a network appliance and simultaneously support viewing, recording, and
playback of video. The Network Video Recorder shall be TCP/IP and HTTP
compliant, enabling administrators to provide better corporate deployment, and
provide a standard format for server management.
1.05 SUBMITTALS
A. General: Submittals shall be made in accordance with the Conditions of the
Contract and Submittal Procedures Section.
B. Shop Drawings and Schematics: Shall depict the Network Video Recorder in
final proposed “as built” configuration. The following must be provided:
1. Connection diagrams for interfacing equipment.
2. List of connected equipment.
3. Locations for all major equipment components to be installed under this
specification.
C. Product Data: The following shall be provided:
1. Technical data sheets.
2. A complete set of instruction manuals.
D. Quality Assurance Submittals: The following shall be submitted:
1. Checkout Report: The Contractor shall provide the Owner with a
checkout report for each Network Video Recorder. The report shall
include:
a. A complete list of every device.
b. The date it was tested, and by whom.
c. If retested, the date it was retested, and by whom.
d. The final test report shall indicate that every device was tested
successfully.
2. Manufacturer’s Instructions: The Contractor shall deliver TBD sets of
System Operation and Maintenance Manuals (if available) to the Owner.
AMERICAN DYNAMICS
TM
NETWORK VIDEO RECORDER
8200-2608-01 B0 VideoEdge® Network Video Recorder 2 of 20
Architect & Engineer Specification
V
3. Notice of Completion: When the final acceptance has been satisfactorily
completed, the Owner shall issue a notice of completion to the
Contractor.
IDEOEDGE
AMERICAN DYNAMICS
TM
NETWORK VIDEO RECORDER
1.06 QUALITY ASSURANCE
A. Manufacturer’s Qualifications: The Network Video Recorder shall be developed
and manufactured by a reputable Fortune 100 company with more than 20 years
of manufacturing experience in the security industry.
B. The Network Video Recorder manufacturer shall include on their public website
a minimum of the following tools, directly related to the support of the Network
Video Recorder system:
1. Application Solutions
2. Digital Demo Network
3. Software Downloads
4. Support Documents
5. Software Registration
6. Training Information and Registration
C. Contractor Qualifications: The Contractor shall be a factory authorized and
certified installer of the security equipment supplied in this project and shall have
been regularly engaged in the installation of the type of security equipment,
hardware, and software specified herein for a period of not less than TBD years.
The contractor shall be factory trained on the Network Video Recorder and
products they propose and shall submit with their proposal a certificate from the
manufacturer indicating their satisfactory completion of training for the Network
Video Recorder proposed. Proposals submitted without this certificate shall be
considered non-responsive and shall not be accepted.
1.07 DELIVERY, STORAGE, AND HANDLING
A. General: Delivery, storage, and handling of the Network Video Recorder shall be in
accordance with the manufacturer’s recommendations.
B. Ordering: The manufacturer’s ordering instructions and lead-time requirements must
be followed in order to avoid installation delays.
C. Delivery: The Network Video Recorder shall be delivered in the manufacturer’s
original, unopened, undamaged container with identification labels intact.
D. Storage and Protection: The Network Video Recorder shall be stored and protected
from exposure to harmful weather conditions and at the environmental conditions
recommended by the manufacturer.
8200-2608-01 B0 VideoEdge® Network Video Recorder 3 of 20
Architect & Engineer Specification
V
IDEOEDGE
1.08 PROJECT CONDITIONS
This section is determinate of owner’s requirements. Left intentionally blank, but should
be filled in, if applicable, by owner or consultant.
1.09 SEQUENCING
This section is determinate of owner’s requirements. Left intentionally blank, but should
be filled in, if applicable, by owner or consultant.
1.10 SCHEDULING
This section is determinate of owner’s requirements. Left intentionally blank, but should
be filled in, if applicable, by owner or consultant.
1.11 WARRANTY
A. Software products have standard 90 Days from American Dynamics
B. Hardware products have standard 3 Years from American Dynamics
C. Hard disk drives have standard 2 Years from American Dynamics
D. Annual SSA (Software Support Agreements or Maintenance Agreements) provide
additional one year of support and updates for software products
1.12 MAINTENANCE
A. Preventative Maintenance Agreement during Warranty: As a separate price item, the
Contractor shall provide preventative maintenance during the warranty period.
Maintenance shall include, but no be limited to:
1. Labor and materials, at no additional cost, to repair Network Video
Recorder Digital Servers.
2. Labor and materials, at no additional cost, to provide test and
adjustments to the Network Video Recorder Servers.
3. Regular inspections.
B. Preventative Maintenance Agreement: As a separate price item, the Contractor shall
provide a complete Maintenance Agreement for a period of TBD months after the
conclusion of the warranty period. The Maintenance Agreement shall include, but
not be limited to:
1. Labor and materials, at no additional cost, to repair Network Video
Recorder Servers.
2. Labor and materials, at no additional cost, to provide test and
adjustments to the Network Video Recorder Servers.
3. Regular inspections.
AMERICAN DYNAMICS
TM
NETWORK VIDEO RECORDER
8200-2608-01 B0 VideoEdge® Network Video Recorder 4 of 20
Architect & Engineer Specification
V
IDEOEDGE
AMERICAN DYNAMICS
TM
NETWORK VIDEO RECORDER
1.13 TRAINING
A. Operator training shall be conducted for a minimum of TBD sessions, with a
session length of TBD hours at the customer’s site.
B. Training shall include, but not be limited to Network Video Recorder operation
and diagnostics.
PART 2 – PRODUCTS
2.01 MANUFACTURED UNITS
A. Model Number/Descriptions Table
VideoEdge Network Video Recorder Model Numbers:
ADNSNVR-CL1
ADNSNVR-CL2
ADNSNVR-CL3
ADNSNVR-UPG-CL1
ADNSNVR-UPG-CL2
ADNSNVR-UPG-CL3
ADN016S0150
ADN024S0300
ADN032S0375
VideoEdge NVR Server Software v2.05,
One Camera Slot License (1-to-64 Total Camera Slots)
VideoEdge NVR Server Software v2.05,
One Camera Slot License (65-to-249 Total Camera Slots)
VideoEdge NVR Server Software v2.05,
One Camera Slot License (250+ Total Camera Slots)
One Camera Slot Upgrade License (1-to-64 Total Additional Camera Slots)
One Camera Slot Upgrade License (65-to-249 Total Additional Camera Slots)
One Camera Slot Upgrade License (250+ Total Additional Camera Slots)
VideoEdge NVR Bundled Server, VideoEdge NVR v2.05 and 16-Slot License
Quad-Core CPU, 4GB RAM, Dual Gigabit NICs, 1.50 TB of Video Storage
VideoEdge NVR Bundled Server, VideoEdge NVR v2.05 and 24-Slot License
Quad-Core CPU, 4GB RAM, Dual Gigabit NICs, 3.00 TB of Video Storage
VideoEdge NVR Bundled Server, VideoEdge NVR v2.05 and 32-Slot License
Quad-Core CPU, 4GB RAM, Dual Gigabit NICs, 3.75 TB of Video Storage
VideoEdge Management Suite Model Numbers:
ADNSCX-SM
ADNSVXC-STN
ADNSVXC-VWC
ADNSVMX-AGT
ADNSCX-AMC American Dynamics Cx Alert Console Software v2.3
ADNSCX-PDA
American Dynamics Cx Site Manager Server Software v2.3
American Dynamics Vx Client Software – Standard Mode v8.3
American Dynamics Vx Client Software – Video Wall Controller Mode v8.3
VideoEdge VMx Agent Software v2.3
American Dynamics Cx Mobile Alert Software v2.3
2.02 SYSTEM PERFORMANCE
8200-2608-01 B0 VideoEdge® Network Video Recorder 5 of 20
Architect & Engineer Specification
V
A. The Network Video Recorder running on VideoEdge NVR software v2.05 must
meet the following minimum features, functions and specifications:
1. The Network Video Recorder and its components shall be thoroughly tested
before shipping from the manufacturer’s facility.
2. The Network Video Recorder shall be a turn-key software solution,
3. The Network Video Recorder software shall be provided as a bootable ISO
image or bootable disc. It shall install from a single program that is launched
from the bootable disc and automatically scan the server’s hardware
configuration. The complete Network Video Recorder software installation
process onto an unpartitioned and unformatted hard drive shall be completed
within minutes.
4. The Network Video Recorder software shall transform standard server
hardware into an IP addressable enterprise appliance server designed for
video surveillance. It shall operate as a read-only platform that prevents the
installation of any third party software and restricts any file-level access to
provide for a stronger level of virus protection and ensure a higher up-time
operation in a commercial/industrial environment.
5. The Network Video Recorder software shall include and install a hardened
and embedded Linux operating system (OS) that must be part of the
automatic installation program. Third party operating system or patch
management shall not be required.
6. The Network Video Recorder software shall include and install a web server
that must be part of the automatic installation program. This shall provide a
standard interface for administrators and clients to view, control, and/or
manage the Network Video Recorder from a standard web browser. The
latest list of supported browsers must be available on the manufacturer’s web
site.
7. The Network Video Recorder software shall include driver support for IP
fixed cameras, IP pan-tilt-zoom cameras, IP MegaPixel cameras, and analog
cameras using IP encoders that are from a variety of manufacturers.
Supported cameras shall be easily interchangeable between different models
without the need to register each individual MAC address. The latest list of
supported devices must be available on the manufacturer’s web site.
8. The Network Video Recorder software shall include driver support for a
variety of standard network interface cards, host bus adapters, and large hard
disk storage devices that are utilized by the server for network connectivity
and storing video data. The latest list of supported devices must be available
on the manufacturer’s web site.
9. The Network Video Recorder software shall include driver support for a
variety of standard network interface cards, host bus adapters, and large hard
IDEOEDGE
AMERICAN DYNAMICS
TM
NETWORK VIDEO RECORDER
8200-2608-01 B0 VideoEdge® Network Video Recorder 6 of 20
Loading...