American Dryer Corp AD-30V User Manual

Page 1
AD-30V / AD-50V
Parts Manual
Phase 7 / Dual Timer
(for models mfd. as of July 1, 2002)
American Dryer Corporation
88 Currant Road
Fall River, MA 02720-4781
Telephone: (508) 678-9000 / Fax: (508) 678-9447
www.amdry.com
ADC Part No. 450438 -5
Page 2
Retain This Manual In A Safe Place For Future Reference
American Dryer Corporation products embody advanced concepts in engineering, design, and safety . If this product is properly maintained, it will provide many years of safe, efficient, and trouble free operation.
ONLY qualified technicians should service this equipment.
OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation manual included with the dryer.
The following “FOR YOUR SAFETY” caution must be posted near the dryer in a prominent location.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
We have tried to make this manual as complete as possible and hope you will find it useful. ADC reserves the right to make changes from time to time, without notice or obligation, in prices, specifications, colors, and material, and to change or discontinue models.
Ne pas entreposer ni utiliser d’essence ni d’autres vapeurs ou liquides inflammables à proximité de cet appareil ou de tout autre appareil.
POUR VOTRE SÉCURITÉ
Important
For your convenience, log the following information:
DATE OF PURCHASE ____________________________________________________ MODEL NO. ______________
RESELLER’S NAME _________________________________________________________________________________
Serial Number(s)_____________________________________________________________________________________
____________________________________________________________________________________________________
____________________________________________________________________________________________________
Replacement parts can be obtained from your reseller or the ADC factory . When ordering replacement part s from the factory , you can FAX your order to ADC at (508) 678-9447 or telephone your order directly to the ADC Parts Department at (508) 678-9000. Please specify the dryer model number and serial number in addition to the description and part number, so that your order is processed accurately and promptly.
The illustrations on the following pages may not depict your particular dryer exactly . The illustrations are a composite of the various dryer models. Be sure to check the descriptions of the parts thoroughly before ordering.
“IMPORTANT NOTE TO PURCHASER”
Information must be obtained from your local gas supplier on the instructions to be followed if the user smells gas. These instructions must be posted in a prominent location near the dryer.
Page 3
Table of Contents
Phase 7 OPL Control Door Assembly....................................................................................................................................................................... 4
Dual Timer Control Door Assembly ........................................................................................................................................................................... 5
Coin Control Door Assembly ..................................................................................................................................................................................... 6
Phase 7 OPL Microprocessor Control Panel Assembly ........................................................................................................................................... 7
Phase 7 Coin Microprocessor Control Panel Assembly .......................................................................................................................................... 8
Dual Timer “Tap Touch” Controls .............................................................................................................................................................................. 9
Phase 7 OPL Microprocessor Control Box Assembly............................................................................................................................................ 10
Phase 7 Coin Microprocessor Control Box Assembly ........................................................................................................................................... 11
Dual Timer Control Box Assembly .......................................................................................................................................................................... 12
Coin Vault Assembly................................................................................................................................................................................................ 13
AD-30V Front Panel Assembly................................................................................................................................................................................ 14
AD-50V Front Panel Assembly................................................................................................................................................................................ 15
Main Door “Steel” Assembly .................................................................................................................................................................................... 16
Main Door Switch Assembly.................................................................................................................................................................................... 17
AD-30V Drop Hatch Lint Door Assembly................................................................................................................................................................ 18
AD-30V Lint Trap Assembly .................................................................................................................................................................................... 19
AD-50V Lint Drawer / Lint Drawer Switch Assemblies ........................................................................................................................................... 20
Idler Bearing Assembly ............................................................................................................................................................................................ 21
Tumbler Bearing Assembly ..................................................................................................................................................................................... 22
AD-30V Tumbler / Support Assemblies .................................................................................................................................................................. 24
AD-50V Tumbler / Support Assemblies .................................................................................................................................................................. 25
AD-30V Non-Reversing Motor Mount Assembly .................................................................................................................................................... 26
AD-30V Reversing Motor Mount Assembly ............................................................................................................................................................ 28
AD-50V Non-Reversing Motor Mount Assembly .................................................................................................................................................... 30
AD-50V Reversing Motor Mount Assembly ............................................................................................................................................................ 32
AD-30V Sensor Bracket Assemblies ...................................................................................................................................................................... 34
AD-50V Sensor Bracket Assemblies ...................................................................................................................................................................... 36
AD-30V Gas Burner Assembly ................................................................................................................................................................................ 38
AD-30V CE Burner Assembly ................................................................................................................................................................................. 40
AD-50V Burner Assembly ........................................................................................................................................................................................ 42
AD-50V CE Burner Assembly ................................................................................................................................................................................. 44
Electric Oven Assembly ........................................................................................................................................................................................... 46
Gas Burner Sail Switch / Hi-Limit Assemblies ....................................................................................................................................................... 48
Phase 7 OPL Single-Phase (1ø) Rear Relay Panel Assembly ............................................................................................................................. 50
Phase 7 OPL 208-416V 3-Phase (3ø) Rear Relay Panel Assembly..................................................................................................................... 52
Phase 7 OPL 460-480V Rear Relay Panel Assembly ........................................................................................................................................... 54
Phase 7 OPL 208-416V Reversing Rear Relay Panel Assembly .......................................................................................................................... 56
Phase 7 OPL 460-480V Reversing Rear Relay Panel Assembly .......................................................................................................................... 58
Dual Timer Single-Phase (1ø) Relay Panel Assembly........................................................................................................................................... 60
Dual Timer 208-416V 3-Phase (3ø) Relay Panel Assembly .................................................................................................................................. 62
Dual Timer 460-480V Electric Relay Panel Assembly ........................................................................................................................................... 64
Dual Timer 208-416V Reversing Relay Panel Assembly ....................................................................................................................................... 65
Dual Timer 460-480V Reversing Relay Panel Assembly ....................................................................................................................................... 66
AD-30V Steam Coil / Air-Operated Steam Damper Assembly .............................................................................................................................. 67
AD-50V Steam Coil / Air-Operated Steam Damper Assembly .............................................................................................................................. 68
Fire Suppression System Assemblies .................................................................................................................................................................... 69
AD-30V Outer Top / Back Guard Assemblies ......................................................................................................................................................... 70
AD-50V Outer Top / Back Guard Assemblies ......................................................................................................................................................... 71
AD-30V Oven Component Application Chart ......................................................................................................................................................... 72
AD-50V Micro Electric Oven Component Application Chart.................................................................................................................................. 73
AD-50V Dual Timer Electric Oven Component Application Chart ......................................................................................................................... 74
Additional Parts Available / Tools Available ............................................................................................................................................................ 75
Page 4

Phase 7 OPL Control Door Assembly

Illus. No. Part No. Qty. Description
1 883574 1 White OPL Control Door
(includes illus. nos. 1 and 3)
883746 1 Coral Blue OPL Control Door
(includes illus. nos. 1 and 3)
883747 1 Ivory OPL Control Door
(includes illus. nos. 1 and 3) 2 150321 2 #10-32 x 1/2” Phillips Machine Screw 3 117604 4 Noise Suppression Tape (sold by the foot) 4 150317 2 #10-16 x 3/4” TORX PLUS 5 102502 1 Control Door Support Rod 6 154011 2 #10-32 Multi-Thread U-Nut 7 102603 1 Control Door Rod Support Catch 8 102601 1 Control Door Retainer Clip
4 American Dryer Corporation 450438 - 5
®
Screw
Page 5

Dual Timer Control Door Assembly

Illus. No. Part No. Qty. Description
1 112301 1 ADC Logo with Tape
870011 1 Double Sided Tape Kit
2 883550 1 White Control Door Assembly
(includes illus. nos. 2 and 3)
883551 1 Ivory Control Door Assembly
(includes illus. nos. 2 and 3)
883552 1 Coral Blue Control Door Assembly
(includes illus. nos. 2 and 3) 3 117604 3 Noise Suppression Tape (sold by the foot) 4 150317 2 #10-16 x 3/4” TORX PLUS 5 102603 1 Control Door Rod Support Catch 6 102601 1 Control Door Rod Retainer Clip 7 102502 1 Control Door Support Rod 8 150321 2 #10-32 x 1/2” Phillips Machine Screw 9 154011 2 #10-32 Multi-Thread U-Nut
450438-5 www.amdry.com 5
®
Screw
Page 6

Coin Control Door Assembly

Illus. No. Part No. Qty. Description
1 823147* 1 Phase 7 Coin Control Door Assembly
(includes illus. nos. 1 through 5) 2 117604 4 Neoprene Sponge Tape (sold by the foot) 3 152014 4 1/4-20 Free Spin Wash Nut 4 117604 2 Neoprene Sponge Tape (sold by the foot) 5 817141* 1 Coin Control Door Trim 6 112301 1 ADC Logo 7 160015 1 Lock with Hardware and Key (Keyed MK-100)
160104 1 Key ONLY (Keyed MK-100)
8 160016 1 Lock Cam ONLY
* Specify color when ordering.
6 American Dryer Corporation 450438 - 5
Page 7

Phase 7 OPL Microprocessor Control Panel Assembly

Illus. No. Part No. Qty. Description
1 112577 1 Phase 7 OPL Keypad 2 850984 1 Phase 7 OPL Microprocessor Panel ONLY 3 887003 1 Phase 7 OPL Microprocessor ONLY (with S.A.F.E.)
887024 1 Phase 7 OPL Microprocessor ONLY (no S.A.F.E.)
(for models mfd. as of December 3, 2003)
887000 1 Phase 7 OPL Microprocessor ONLY (with S.A.F.E.)
(for models mfd. prior to December 3, 2003) 4 150005 2 #6-32 x 3/4” Phillips Round Head Machine Screw 5 153010 2 #6 Star Washer 6 136097 1 500 mA Fuse 7 136016 1 5-Amp Fuse
450438-5 www.amdry.com 7
Page 8

Phase 7 Coin Microprocessor Control Panel Assembly

Illus. No. Part No. Qty. Description
1 137250 1 Phase 7 Coin Ribbon Cable 2 137270 1 16” x 1” Large Character Display 3 887011 1 Phase 7 Coin Board
(for models mfd. without S.A.F.E.)
887012 1 Phase 7 Coin Board
(for models mfd. with S.A.F.E. and mfd. as of December 3, 2003)
887009 1 Phase 7 Coin Board
(for models mfd. with S.A.F.E. and mfd. prior to December 3, 2003) 4 112575 1 Phase 7 Keypad 5 153010 4 #6 Internal and External Star Washers 6 150005 4 #6-32 x 1/4” Phillips Round Head Machine Screw 7 152102 4 M3 Metric Hex Nut 8 823145 1 Phase 7 Coin Control Panel ONLY 9 818232 1 25¢ Coin Acceptor
883774 1 Hanke/Munzprufer Optic Switch ONLY
8 American Dryer Corporation 450438 - 5
Page 9
Dual Timer “Tap Touch” Controls
Illus. No. Part No. Qty. Description
1 824298 1 15 Minute Timer – 24 VAC 2 824299 1 60 Minute Timer – 24 VAC 3 824175 1 Red Pilot Light – 24 VAC 4 122301 1 “Tap Touch” Switch 5 131932 3 Relay SPST 24v 6 120731 1 30-Position Terminal Block 7 151000 6 #6-32 Pal Nut 8 882903 1 Dual Timer Panel Complete
(includes illus. nos. 1 through 15)
850392 Dual Timer Panel ONLY 9 153010 2 #6 Star Washer 10 152000 2 #6-32 Hex Nut 11 150108 2 #8-32 x 1/2” Phillips Pan Head Machine Screw 12 150110 4 #8-32 x 1/4” Phillips Round Head Machine Screw 13 112563 1 Dual Timer Panel Overlay 14 124104 1 Pure Touch Knob with Red Pointer 15 124105 1 Pure Touch Knob with Blue Pointer
450438-5 www.amdry.com 9
Page 10

Phase 7 OPL Microprocessor Control Box Assembly

Illus. No. Part No. Qty. Description
1 122681 1 10-Pin Connector 2 122676 1 8-Pin Connector 3 122646 1 2-Pin Connector 4 122683 1 6-Pin Connector 5 122640 1 9-Pin Connector 6 122706 * #20-16 U.M.N.L. Socket 7 122669 * Female Crimp Terminal
* As needed.
10 American Dryer Corporation 450438 - 5
Page 11

Phase 7 Coin Microprocessor Control Box Assembly

Illus. No. Part No. Qty. Description
1 122681 1 10-Pin Connector 2 122676 1 8-Pin Connector 3 122646 1 2-Pin Connector 4 122669 * Female Crimp Terminal 5 122640 1 9-Pin Connector 6 122706 * #20-16 U.M.N.L. Socket
* As needed.
450438-5 www.amdry.com 11
Page 12

Dual Timer Control Box Assembly

Illus. No. Part No. Qty. Description
1 122641 1 15-Pin Connector 2 122706 * Socket Terminal
122801 1 Pin / Socket Extraction Tool … Not Illustrated 3 150301 2 #8-18 x 7/16” Phillips Pan Head TEK Screw 4 884252 1 Reversing Timer 24v (for reversing dual timer models Only)
* As required.
12 American Dryer Corporation 450438 - 5
Page 13

Coin Vault Assembly

Illus. No. Part No. Qty. Description
1 884050 1 Microprocessor Coin Vault Assembly Complete
(includes illus. nos. 1 through 6)
823143 1 Microprocessor Coin Vault ONLY 2 160028 1 Cam for 1/4” Turn Lock ONLY 3 875061 1 1/4” Turn Lock with Key and Cam
160105* 1 1/4” Turn Mer-Pel Key ONLY 4 802020 1 1/4” Turn Coin Box Assembly
(includes illus. nos. 2 through 5) 802019 1 1/4” Turn Coin Box ONLY without Faceplate 125915 1 High Security (Greenwald) Coin Box ONLY with Key (each keyed different)
5 802018 1 1/4” Turn Coin Box Faceplate ONLY 6 152014 4 1/4-20 Free Spin Wash Nut 7 102502 1 Control Door Support Rod 8 102601 1 Control Door Rod Retainer Clip 9 102603 1 Control Door Rod Catch
* Specify key number when ordering.
450438-5 www.amdry.com 13
Page 14

AD-30V Front Panel Assembly

Illus. No. Part No. Qty. Description
1 822686* 1 RH “Magnet” Front Panel Assembly
(includes illus. nos. 1, 7, and 8) (for models mfd. as of August 22, 2007)
822684* 1 LH “Magnet” Front Panel Assembly
(includes illus. nos. 1, 7, and 8) (for models mfd. as of August 22, 2007)
883567 1 RH White Latch Front Panel Assembly
(includes illus. nos. 1, 5, and 6) (for models mfd. prior to August 22, 2007)
883568 1 RH Coral Blue Latch Front Panel Assembly
(includes illus. nos. 1, 5, and 6) (for models mfd. prior to August 22, 2007)
883569 1 RH Ivory Latch Front Panel Assembly
(includes illus. nos. 1, 5, and 6) (for models mfd. prior to August 22, 2007)
2 150313 11 #10-16 x 1/2” TORX PLUS
150318 1 25 IP TORX PLUS
®
®
Screw
Bit (for removal of TORX® head screw)
3 –––––– 1 Main Door Hinge
(refer to Main Door “Steel” Assembly on page 16) 4 122002 1 Lint Drawer Switch 5 170330 1 Friction Door Latch (latch door version Only) 6 154215 2 5/32” Pop Rivet (latch door version Only) 7 102004 2 0.750 Round Main Door Magnet 8 152223 2 1/2” TORX
®
Head Screw
* Specify color when ordering.
14 American Dryer Corporation 450438 - 5
Page 15

AD-50V Front Panel Assembly

Illus. No. Part No. Qty. Description
1 822669* 1 RH “Magnet” Front Panel Assembly
(includes illus. nos. 1, 7, and 8) (for models mfd. as of June 18, 2007)
822671 1 RH Stainless Steel “Magnet” Front Panel Assembly
(includes illus. nos. 1, 7, and 8) (for models mfd. as of June 18, 2007)
822673* 1 LH “Magnet” Front Panel Assembly
(includes illus. nos. 1, 7, and 8) (for models mfd. as of June 18, 2007)
883137 1 RH White Front Panel Assembly
(includes illus. nos. 1, 5, and 6) (for models mfd. prior to June 18, 2007)
883138 1 RH Coral Blue Front Panel Assembly
(includes illus. nos. 1, 5, and 6) (for models mfd. prior to June 18, 2007)
883139 1 RH Ivory Front Panel Assembly
(includes illus. nos. 1, 5, and 6) (for models mfd. prior to June 18, 2007)
2 150313 11 #10-16 x 1/2” TORX PLUS
150318 1 25 IP TORX PLUS
®
Bit (for removal of TORX® head screw)
3 –––––– 1 Main Door Hinge
(refer to Main Door “Steel” Assembly on page 16)
4 –––––– 1 Lint Drawer Switch
(refer to AD-50V Lint Drawer / Lint Drawer Switch Assemblies on page 20) 5 170330 1 Friction Door Latch 6 154215 2 5/32” Pop Rivet 7 102004 2 0.750 Round Main Door Magnet 8 152223 2 1/2” TORX
®
Head Screw
®
Screw
* Specify color when ordering.
450438-5 www.amdry.com 15
Page 16
Main Door “Steel” Assembly
Illus. No. Part No. Qty. Description
1 822661 1 Magnet Black Main Door Assembly Complete
(for AD-50V models mfd. as of June 18, 2007 and AD-30V as of August 22, 2007) (includes illus. nos. 1, 2, 8, 9, and 12 through 16)
881150 1 Latch Black Main Door Assembly Complete
(for AD-50V models mfd. prior to June 18, 2007 and AD-30V prior to August 22, 2007) (includes illus. nos. 1, 2, 8, and 9 through 15)
2 102354 1 Door Gasket
401010 1 Mastic Adhesive (5 oz. tube)
3 881152 1 Black Top Hinge Block Assembly
(includes illus. nos. 3 and 4) 4 150445 2 1/4-20 x 3/4” Black Cap Head Setscrew 5 153031 1 1/4” Nylon Washer 6 881151 1 Black Bottom Hinge Block Assembly
(includes illus. nos. 5 through 7) 7 150445 2 1/4-20 x 3/4” Black Cap Head Setscrew 8 150683 3 1/4-20 x 5/8” Black Carriage Bolt 9 152014 3 1/4-20 Free Spin Wash Nut 10 151010 1 #10-32 Black Hex Acorn Nut (latch models Only) 11 150120 1 Door Screw (latch models Only) 12 150683 3 1/4-20 x 5/8” Black Carriage Bolt 13 152014 3 1/4-20 Free Spin Wash Nut 14 881210 1 Black Main Door Handle ONLY 15 102211 1 20-7/16” Door Glass
170730 1 Adhesive (10.3 oz. cartridge)
16 319298 2 Magnet Bracket
(for AD-50V models mfd. as of June 18, 2007 and AD-30V as of August 22, 2007)
16 American Dryer Corporation 450438 - 5
Page 17

Main Door Switch Assembly

Illus. No. Part No. Qty. Description
1 150006 2 #6-32 x 7/8” Phillips Pan Head Machine Screw 2 152013 2 #6-32 Hex Nut 3 153010 2 #6 Star Washer 4 137005 1 Door Switch 5 122636 2 Flag Terminal 6 881211 1 Black Main Door Switch Housing ONLY
(includes illus. nos. 1 and 6)
881153 1 Black Main Door Switch Housing Complete
(includes illus. nos. 1 through 4 and 6)
7 150301 2 #8-18 x 7/16” Phillips Pan Head TEK Screw
450438-5 www.amdry.com 17
Page 18

AD-30V Drop Hatch Lint Door Assembly

Illus. No. Part No. Qty. Description
1 883680 1 White Drop Lint Door Assembly (non-coin Only)
(includes illus. nos. 1 through 3)
883656 1 Coral Blue Drop Lint Door Assembly (non-coin Only)
(includes illus. nos. 1 through 3)
883657 1 Ivory Drop Lint Door Assembly (non-coin Only)
(includes illus. nos. 1 through 3)
802265* 1 Drop Hatch Lint Door Assembly (coin Only)
(includes illus. nos. 1 through 3) 2 117604 6 Noise Suppression Tape (sold by the foot) 3 170226 1 Slide Latch (non-coin Only)
160001 1 AD-100 Lock with Cam and Key (coin Only) 160016 1 1-1/4” Cam ONLY (coin Only) 160103 1 AD-100 Key ONLY (coin Only)
* Specify color when ordering.
18 American Dryer Corporation 450438 - 5
Page 19

AD-30V Lint Trap Assembly

Illus. No. Part No. Qty. Description
1 801070 1 Lint Trap Assembly Complete (for 60 Hz models Only)
(includes illus. nos. 1 and 3 through 5)
800401 1 Lint Trap Assembly Complete (for 50 Hz models Only)
(includes illus. nos. 1 and 3 through 5) 801069 1 Lint Trap ONLY (for 60 Hz models Only) 800443 1 Lint Trap ONLY (for 50 Hz models Only)
2 154200 6 5/32” Pop Rivet 3 150300 3 #10-16 x 1/2” Hex Washer TEK Screw 4 304100 1 Lint Screen Holder 5 800500 2 Lint Screen Assembly
450438-5 www.amdry.com 19
Page 20

AD-50V Lint Drawer / Lint Drawer Switch Assemblies

Illus. No. Part No. Qty. Description
1 850962** 1 Lint Drawer Assembly (non-coin Only)
(for models mfd. as of January 1, 2003)
883795 1 White Lint Drawer Assembly (non-coin Only)
(for models mfd. prior to January 1, 2003)
883796 1 Coral Blue Lint Drawer Assembly (non-coin Only)
(for models mfd. prior to January 1, 2003)
883797 1 Ivory Lint Drawer Assembly (non-coin Only)
(for models mfd. prior to January 1, 2003)
850968** 1 Locking Lint Basket Assembly (coin Only)
(includes illus. nos. 1, 2, and 10) 160001 1 AD-100 Lock with Cam and Key (coin Only) 160103 1 AD-100 Key ONLY (coin Only) 160052 1 Lock Cam ONLY (coin Only)
2 117604 7 Noise Suppression Tape (sold by the foot) 3 122116 1 Lint Drawer Switch 4 122605 * 4-Pin Connector (female) 5 122701 * Socket Terminal
122801 1 Pin / Socket Extraction Tool … Not Illustrated
6 833123 1 Lint Drawer Switch Box Assembly (for Phase 7 models Only)
(includes illus. nos. 3 through 6) 818087 1 Lint Drawer Switch Box Assembly (for dual timer models Only)
(includes illus. nos. 3 through 6) 304136 1 Lint Drawer Switch Box Cover ONLY
7 150301 2 #8-18 x 7/16” Phillips Pan Head TEK Screw 8 122700 * Pin Terminal 9 122604 * 4-Pin Connector (male) 10 817032 1 Lint Bag
(for models mfd. as of January 1, 2003)
* As required. ** Specify color when ordering.
20 American Dryer Corporation 450438 - 5
Page 21

Idler Bearing Assembly

Illus. No. Part No. Qty. Description
1 100100 1 5L-660 V-Belt (tumbler to idler) for Non-Reversing Models ONLY
100108 1 5L-680 V-Belt (tumbler to idler) for Reversing Models ONLY 2 101129 1 9” x 2-1/2” Compound Pulley 3 100105 1 4L-520 V-Belt for Non-Reversing Models ONLY
100112 1 4L-610 V-Belt (idler to motor) for Reversing Models ONLY 4 154301 2 5/16-18 x 1” Allen Setscrew 5 100705 1 3/16” x 3/16” x 1-3/8” Key 6 882576 1 Idler Bearing Assembly Complete
(includes illus. nos. 5 through 12) 7 150617 2 3/8-16 x 1” Hex Head Machine Bolt 8 153005 2 3/8” Lock Washer 9 153004 2 3/8” Flat Washer 10 801009 1 Idler Square Washer 11 152004 1 5/16-18 Hex Nut 12 150509 1 5/16-18 x 3” Hex Head Machine Bolt
450438-5 www.amdry.com 21
Page 22
22 American Dryer Corporation 450438 - 5

Tumbler Bearing Assembly

Page 23
Tumbler Bearing Assembly
Illus. No. Part No. Qty. Description
1 880220 1 1-3/4” Flange Bearing 2 153025 4 9/16” Lock Washer 3 152050 4 9/16-12 Hex Nut 4 883387 1 Pillow Block Bearing Assembly Complete (for micro models Only)
(includes illus. nos. 4 through 18, 23, and 24)
882544 1 Pillow Block Bearing Assembly Complete (for dual timer models Only)
(includes illus. nos. 4 through 16, 23, and 24)
882543 1 Pillow Block Bearing Platform ONLY (for micro models Only) 882542 1 Pillow Block Bearing Platform ONLY (for dual timer models Only)
5 880779 1 1-3/8” Pillow Block Bearing (with Rotation Sensor Magnet illus. 17)
(for micro models Only)
880202 1 1-3/8” Pillow Block Bearing (for dual timer models Only) 6 150601 2 3/8-16 x 2” Hex Bolt 7 153004 2 3/8” Flat Washer 8 153004 2 3/8” Flat Washer 9 153005 2 3/8” Lock Washer 10 152005 2 3/8-16 Hex Nut 11 154321 2 5/16-24 x 3/8” Setscrew 12 152004 2 5/16-18 Hex Nut 13 150621 2 5/16-18 x 1-1/2” Tap Bolt 14 153002 4 5/16” Lock Washer 15 153004 6 3/8” Flat Washer 16 150501 4 5/16-18 x 3/4” Tap Bolt 17 102120 1 Sintered 8 Magnet (for micro models Only) 18 883386 1 Rotational Sensor Assembly (for micro models Only) 19 100735 1 Shaft Key (for reversing models Only) 20 101100 1 18” Pulley (for non-reversing models Only)
101118 1 18-3/4” Pulley (for reversing models Only) 21 10111 0 1 1” Taper Lock Bushing (for reversing models Only) 22 100100 1 5L-660 V-Belt (tumbler to idler) for Non-Reversing Models ONLY
100108 1 5L-680 V-Belt (tumbler to idler) for Reversing Models ONLY 23 150610 2 5/16-18 x 1-1/2” Allen Setscrew 24 152004 2 5/16-18 Hex Nut
450438-5 www.amdry.com 23
Page 24

AD-30V Tumbler / Support Assemblies

Illus. No. Part No. Qty. Description
1* 882519 1 Galvanized Tumbler ONLY
882521 1 Stainless Steel Tumbler ONLY 882522 1 Galvanized Tumbler / Support Assemblies
(includes illus. nos. 1 through 3 and 5 through 11)
882523 1 Stainless Steel Tumbler / Support Assemblies
(includes illus. nos. 1 through 3 and 5 through 11)
2 150313 40 #10-16 x 1/2” TORX PLUS
150318 1 25 IP TORX PLUS
®
Bit (for removal of TORX® head screw)
3 322002 2 Galvanized Taper Tumbler Rib
322003 2 Galvanized Straight Tumbler Rib 322066 2 Stainless Steel Straight Tumbler Rib
322067 2 Stainless Steel Tapered Tumbler Rib 4 116002 1 Felt Collar ONLY 5 100918 4 3/8-16 x 26-3/4” Tie Rod 6 153004 4 3/8” Flat Washer 7 882517 1 Tumbler Support ONLY 8 152027 4 3/8-16 Nylon Insert Locknut 9 153005 4 3/8” Lock Washer 10 153004 4 3/8” Flat Washer 11 115986 1 1/4” x 2” Felt Tumbler Pad
401010 1 #847 Adhesive for Felt Collar (5.0 oz. tube) … Not Illustrated
* Felt collar is not included and must be ordered separately .
®
Screw
24 American Dryer Corporation 450438 - 5
Page 25

AD-50V Tumbler / Support Assemblies

Illus. No. Part No. Qty. Description
1* 800838 1 Galvanized Tumbler ONLY
800736 1 Stainless Steel Tumbler ONLY 800837 1 Galvanized Tumbler and Support Assembly with Tapered Ribs
(includes illus. nos. 1 through 3 and 5 through 11)
882683 1 Stainless Steel Tumbler and Support Assembly with Tapered Ribs
(includes illus. nos. 1 through 3 and 5 through 11)
2 150313 40 #10-16 x 1/2” TORX PLUS
150318 1 25 IP TORX PLUS
®
®
Crimptite Screw
Bit (for removal of TORX® head screw)
3 301302 2 Galvanized Tumbler Rib (low rib) ONLY
301311 2 Galvanized Tumbler Rib (high rib) ONLY 301425 2 Stainless Steel Tumbler Rib
301426 2 Stainless Steel Tapered Rib 4 116001 1 Felt Collar ONLY 5 100903 4 3/8-16 x 38-1/2” Tie Rod 6 153004 4 3/8” Flat Washer 7 800616 1 Tumbler Support ONLY 8 152027 4 3/8-16 Nylon Insert Locknut 9 153005 4 3/8” Lock Washer 10 153004 4 3/8” Flat Washer 11 115986 1 1/4” x 2” Felt Tumbler Pad
401010 1 #847 Adhesive for Felt Collar (5.0 oz. tube) … Not Illustrated
* Felt collar is not included and must be ordered separately.
450438-5 www.amdry.com 25
Page 26
26 American Dryer Corporation 450438 - 5

AD-30V Non-Reversing Motor Mount Assembly

Page 27
AD-30V Non-Reversing Motor Mount Assembly
Illus. No. Part No. Qty. Description
1 100105 1 4L-520 V-Belt (to idler motor) 2 100701 1 3/16” x 3/16” x 1” Key 3 101104 1 1/2” x 2” Motor Pulley (for use on 1ø – 60 Hz models Only)
101132 1 5/8” x 2” Motor Pulley (for use on 3ø – 60 Hz models Only)
101131 1 1/2” x 2-1/4” Motor Pulley
(for use on 1ø 50 Hz models mfd. as of August 22, 2002)
101133 1 5/8” x 2-1/4” Motor Pulley
(for use on all 3ø 50 Hz and 1ø 50 Hz models mfd. prior to August 22, 2002) 4 150501 4 5/16-18 x 3/4” Hex Head Machine Bolt 5 153002 4 5/16” Lock Washer 6 153001 4 5/16” Flat Washer 7 181049 1 1/2 hp 120-230v 1ø 50/60 Hz Motor with Plug
883572 1 1/2 hp 240v 1ø 50 Hz Motor with Plug (includes motor pulley)
(for 1ø 50 Hz models mfd. prior to August 22, 2002 Only) 8 122701 8 Socket Terminal ONLY
122801 1 Pin / Socket Extraction Tool … Not Illustrated 9 137030 1 8-Pin Housing Connector 10 152004 4 5/16-18 Hex Nut 11 153002 4 5/16” Lock Washer 12 153001 4 5/16” Flat Washer 13 117604 4 Noise Suppression Tape (sold by the foot) 14 154000 4 5/16-18 Nut 15 850017 1 Non-Reversing Motor Mount ONLY (56Z frame)
817075 1 1/2 hp 120-230v 1ø 60 Hz Motor Mount Assembly Complete with Plug Motor
(includes illus. nos. 2 through 7 and 13 through 20)
803813 1 1/2 hp 240v 1ø 50 Hz Motor Mount Assembly Complete with Plug Motor
(includes illus. nos. 2 through 7 and 13 through 20)
817080* 1 1/2 hp 208/230/380/460v 3ø 60 Hz Motor Mount Assembly Complete
(includes illus. nos. 2 through 6 and 13 through 22)
803810* 1 1/2 hp 208/230/380/460v 3ø 50 Hz Non-Reversing Motor Mount Assembly Complete
(includes illus. nos. 2 through 6 and 13 through 22) 16 153050 2 1/2” S.A.E. Flat Washer 17 100604 1 12-1/2” Impellor with 1/2” Bore 18 100702 1 1/8” x 1/8” x 1-1/2” Key 19 153050 2 1/2” S.A.E. Flat Washer 20 152006 2 1/2-20 Left Hand Jam Nut 21 120200 1 3/8” 90° Connector 22 100007* 1 1/2 hp 208-460 3ø 50/60 Hz Motor
* Specify volt age when ordering.
450438-5 www.amdry.com 27
Page 28

AD-30V Reversing Motor Mount Assembly

28 American Dryer Corporation 450438 - 5
Page 29
AD-30V Reversing Motor Mount Assembly
Illus. No. Part No. Qty. Description
1 100112 1 4L-610 V-Belt (to idler motor) 2 100701 1 3/16” x 3/16” x 1” Key 3 101132 1 5/8” x 2” Motor Pulley (for 60 Hz models Only)
101133 1 5/8” x 2-1/4” Motor Pulley (for 50 Hz models Only) 4 120200 1 3/8” x 90° Connector 5* 181003 1 1/2 hp 208/230/380/460v 3ø 50/60 Hz Motor (56z frame) 6 150501 4 5/16-18 x 3/4” Hex Head Machine Bolt 7 153002 4 5/16” Lock Washer 8 153001 4 5/16” Flat Washer 9* 100007 1 1/2 hp 208/230/380/460v 3ø 50/60 Hz Totally Enclosed, Fan-Cooled Motor (56z frame) 10 120200 1 3/8” x 90° Connector 11 150501 4 5/16-18 x 3/4” Hex Head Machine Bolt 12 153002 4 5/16” Lock Washer 13 153001 4 5/16” Flat Washer 14 154000 8 5/16-18 Nut 15 152004 4 5/16-18 Hex Nut 16 153002 4 5/16” Lock Washer 17 153001 4 5/16” Flat Washer 18 850070 1 Motor Mount ONLY (56Z frame)
(includes illus. nos. 18 and 19)
803802* 1 Motor Mount Assembly Complete for 60 Hz Models ONLY
(includes illus. nos. 2 through 14 and 18 through 24)
803803* 1 Motor Mount Assembly Complete for 50 Hz Models ONLY
(includes illus. nos. 2 through 14 and 18 through 24) 19 117604 4 Noise Suppression Tape (sold by the foot) 20 153050 2 1/2” S.A.E. Flat Washer 21 100702 1 1/8” x 1/8” x 1-1/2” Key 22 100604 1 12-1/2” Impellor with 1/2” Bore 23 153050 2 1/2” S.A.E. Flat Washer 24 152006 2 1/2-20 Left Hand Jam Nut
* Specify volt age when ordering.
450438-5 www.amdry.com 29
Page 30

AD-50V Non-Reversing Motor Mount Assembly

30 American Dryer Corporation 450438 - 5
Page 31
AD-50V Non-Reversing Motor Mount Assembly
Illus. No. Part No. Qty. Description
1 100105 1 4L-520 V-Belt (motor to idler) 2 100701 1 3/16” x 3/16” x 1” Key 3 101132 1 5/8” x 2” Motor Pulley (for use on 60 Hz models Only)
101133 1 5/8” x 2-1/4” Motor Pulley (for use on 50 Hz models Only) 4 150501 4 5/16-18 x 3/4” Hex Head Machine Bolt 5 153002 4 5/16” Lock Washer 6 153001 4 5/16” Flat Washer 7 100069 1 3/4 hp 120-230v 1ø Totally Enclosed, Fan-Cooled Motor with Plug (56Z frame)
For 60 Hz Models ONLY
100068 1 3/4 hp 240v 1ø Totally Enclosed, Fan-Cooled Motor with Plug (56Z frame)
For 50 Hz Models ONLY
8 122701 8 Socket Terminal ONLY
122801 1 Pin / Socket Extraction Tool … Not Illustrated 9 137030 1 8-Pin Housing Connector 10 152004 4 5/16-18 Hex Nut 11 153002 4 5/16” Lock Washer 12 153001 4 5/16” Flat Washer 13 117604 4 Noise Suppression Tape (sold by the foot) 14 154000 4 5/16-18 Nut 15 850017 1 Non-Reversing Motor Mount ONLY with Gasket (56Z frame)
(includes illus. nos. 13 and 15)
817029 1 3/4 hp 120-230v 1ø 60 Hz Totally Enclosed, Fan-Cooled
Motor Mount Assembly Complete with Plug Motor (includes illus. nos. 2 through 7 and 13 through 20)
817074 1 3/4 hp 240v 1ø 50 Hz Totally Enclosed, Fan-Cooled
Motor Mount Assembly Complete with Plug Motor (includes illus. nos. 2 through 7 and 13 through 20)
817080* 1 1/2 hp 208/230/380/460v 3ø 60 Hz Motor Mount Assembly Complete
(includes illus. nos. 2 through 6 and 13 through 22)
883271* 1 1/2 hp 208/230/380/460v 3ø 50 Hz Motor Mount Assembly Complete
(includes illus. nos. 2 through 6 and 13 through 22) 16 153050 3 1/2” S.A.E. Flat Washer 17 100604 1 12-1/2” Impellor with 1/2” Bore 18 100702 1 1/8” x 1/8” x 1-1/2” Key 19 153050 1 1/2” S.A.E. Flat Washer 20 152006 2 1/2-20 Left Hand Jam Nut 21 120200 1 3/8” x 90° Connector 22 100007* 1 1/2 hp 208/230/380/460v 3ø 50/60 Hz Motor (56Z frame)
* Specify volt age when ordering.
450438-5 www.amdry.com 31
Page 32

AD-50V Reversing Motor Mount Assembly

32 American Dryer Corporation 450438 - 5
Page 33
AD-50V Reversing Motor Mount Assembly
Illus. No. Part No. Qty. Description
1 100112 1 4L-610 V-Belt (motor to idler) 2 100701 1 3/16” x 3/16” x 1” Key 3 101132 1 5/8” x 2” Motor Pulley (for 60 Hz models Only)
101133 1 5/8” x 2-1/4” Motor Pulley (for 50 Hz models Only) 4 120200 1 3/8” x 90° Connector 5* 181003 1 1/2 hp 208/230/380/460v 3ø 50/60 Hz (56Z frame) 6 150501 4 5/16-18 x 3/4” Hex Head Machine Bolt 7 153002 4 5/16” Lock Washer 8 153001 4 5/16” Flat Washer 9* 100007 1 1/2 hp 208/230/380/460v 3ø 50/60 Hz Motor (56Z frame) 10 120200 1 3/8” x 90° Connector 11 150501 4 5/16-18 x 3/4” Hex Head Machine Bolt 12 153002 4 5/16” Lock Washer 13 153001 4 5/16” Flat Washer 14 154000 8 5/16” Nut 15 152004 7 5/16” Hex Nut 16 153002 4 5/16” Lock Washer 17 153001 4 5/16” Flat Washer 18 850070 1 Motor Mount ONLY with Gasket (56Z frame)
(includes illus. nos. 18 and 19)
803802* 1 60 Hz Motor Mount Assembly Complete
(includes illus. nos. 2 through 14 and 18 through 24)
803803* 1 50 Hz Motor Mount Assembly Complete
(includes illus. nos. 2 through 14 and 18 through 24) 19 117604 4 Noise Suppression Tape (sold by the foot) 20 153050 1 1/2” S.A.E. Flat Washer 21 100702 1 1/8” x 1/8” x 1-1/2” Key 22 100604 1 12-1/2” Impellor with 1/2” Bore 23 153050 2 1/2” S.A.E. Flat Washer 24 152006 2 1/2-20 Left Hand Jam Nut
* Specify volt age when ordering.
450438-5 www.amdry.com 33
Page 34

AD-30V Sensor Bracket Assemblies

34 American Dryer Corporation 450438 - 5
Page 35
AD-30V Sensor Bracket Assemblies
Illus. No. Part No. Qty. Description
1 880251 1 1/4” Temperature Sensor Probe Assembly
(includes illus. nos. 1 and 5 through 8) 2 130301 1 225° Hi-Limit Thermostat 3 153010 2 #6 Star Washer 4 152000 2 #6-32 Hex Nut 5 121028 2 Insulated Terminal 6 122701 4 Socket Terminal 7 122605 1 4-Pin Connector (female) 8 154007 2 1/4” Push-On Fastener 9 150005 2 #6-32 x 1/4” Round Head Machine Screw 10 801424 1 Microprocessor Sensor Bracket Assembly Complete
(includes illus. nos. 1 through 10)
305007 1 Sensor Bracket ONLY 11 122604 1 4-Pin Connector (male) 12 122700 4 Pin Terminal 13 150301 2 #8-18 x 7/16” Phillips Pan Head TEK Screw 14 150005 5 #6-32 x 1/4” Phillips Round Head Machine Screw 15 130111 1 130° Thermostat 16 130100 1 150° Thermostat 17 130103 1 225° Hi-Limit Thermostat 18 130101 1 180° Thermostat 19 153010 5 #6 Star Washer 20 152000 5 #6-32 Hex Nut 21 882535 1 Sensor Jumper 22 121028 4 Insulated Terminal 23 122701 4 Socket Terminal 24 122605 1 4-Pin Connector (female)
882534 1 Sensor Bracket Harness Assembly
(includes illus. nos. 22 through 24)
25 818321 1 Noncomputer Sensor Bracket Assembly Complete
(includes illus. nos. 14 through 25)
305007 1 Sensor Bracket ONLY 26 122604 1 4-Pin Connector (male) 27 122700 4 Pin Terminal
122801 1 Pin / Socket Extraction Tool … Not Illustrated 28 150301 2 #8-18 x 7/16” Phillips Pan Head TEK Screw
450438-5 www.amdry.com 35
Page 36

AD-50V Sensor Bracket Assemblies

36 American Dryer Corporation 450438 - 5
Page 37
AD-50V Sensor Bracket Assemblies
Illus. No. Part No. Qty. Description
1 880251 1 1/4” Temperature Sensor Probe Assembly
(includes illus. nos. 1 and 5 through 8) 2 130103 1 225° Hi-Limit Thermostat 3 153010 2 #6 Star Washer 4 152000 2 #6-32 Hex Nut 5 121028 2 Insulated Terminal 6 122701 4 Socket Terminal 7 122605 1 4-Pin Connector (female) 8 154007 2 1/4” Push-On Fastener 9 150005 2 #6-32 x 1/4” Phillips Round Head Machine Screw 10 817046 1 Microprocessor Sensor Bracket Assembly Complete
(includes illus. nos. 1 through 10)
322214 1 Micro Sensor Bracket ONLY 11 122604 1 4-Pin Connector (male) 12 122700 4 Pin Terminal 13 150301 2 #8-18 x 7/16” Phillips Pan Head TEK Screw 14 150005 5 #6-32 x 1/4” Phillips Round Head Machine Screw 15 130111 1 130° Thermostat 16 130100 1 150° Thermostat 17 130301 1 225° Hi-Limit Thermostat 18 130101 1 180° Thermostat 19 153010 5 #6 Star Washer 20 152000 5 #6-32 Hex Nut 21 882535 1 Sensor Jumper 22 121028 4 Insulated Terminal 23 122701 4 Socket Terminal 24 122605 1 4-Pin Connector (female)
882534 1 Sensor Bracket Harness Assembly
(includes illus. nos. 22 through 24)
25 882536 1 Noncomputer Sensor Bracket Assembly Complete
(includes illus. nos. 14 through 25)
322062 1 Universal Sensor Bracket ONLY 26 122604 1 4-Pin Connector (male) 27 122700 4 Pin Terminal
122801 1 Pin / Socket Extraction Tool … Not Illustrated 28 150301 2 #8-18 x 7/16” Phillips Pan Head TEK Screw
450438-5 www.amdry.com 37
Page 38
38 American Dryer Corporation 450438 - 5

AD-30V Gas Burner Assembly

Page 39
AD-30V Gas Burner Assembly
Illus. No. Part No. Qty. Description
1 141105 2 Large Tube Burner 2 151001 2 #8-32 Pal Nut 3 150108 2 #8-32 x 1/2” Phillips Pan Head Machine Screw 4 140820* 2 #29 Burner Orifice (natural gas)
140806* 2 #46 Burner Orifice (liquid propane gas) 5 141230 1 1/2” Manifold (2-port) 6 318714 1 1-Piece Gas Valve Bracket 7 150309 5 #10-16 x 1/2” Hex Head TEK Crimptite Screw 8 128927 1 1/2” 24 VAC (natural gas) Gas Valve
880960 1 1/2” 24 VAC (liquid propane gas) Gas Valve 9 884265 1 Ignitor Flame-Probe Assembly ONLY 10 887133 1 Direct Spark Ignition Module
(for models mfd. as of March 1, 2004)
883849 1 Direct Spark Ignition Module Kit
(for models mfd. prior to March 1, 2004) 11 810031 1 Direct Spark Ignition Module Mounting Bracket 12 150300 9 #10-16 x 1/2” Hex Washer TEK Screw 13 152013 2 #6-32 Hex Nut 14 141317 1 1/2” Bronze Union Elbow 15 142809 1 1/2” x 29-1/8” Black Pipe 16 830354 1 Direct Spark Ignition Control Wiring Harness 17 884279 1 High Voltage Gray Carbon Wire with Terminal
(for models mfd. as of March 1, 2004)
128919 1 High Voltage Red Wire
(for models mfd. prior to March 1, 2004) 18 817060** 1 Direct Spark Ignition Burner Assembly Complete (less orifice) (natural gas)
(includes illus. nos. 1 through 3 and 5 through 18)
817061** 1 Direct Spark Ignition Burner Assembly Complete (less orifice) (liquid propane gas)
(includes illus. nos. 1 through 3 and 5 through 18)
850858 1 Burner Box ONLY 882269* 1 AD-30V Liquid Propane Conversion Kit (includes orifices) 880603*** 1 Steam to Gas Interface Assembly
* Consult factory for elevations over 2,000 feet. ** Burner orifices are not included and must be ordered separately. *** Needed when converting steam heat to gas heat.
450438-5 www.amdry.com 39
Page 40
40 American Dryer Corporation 450438 - 5

AD-30V CE Burner Assembly

Page 41
Illus. No. Part No. Qty. Description
1 850858 1 Burner Box ONLY
801190** 1 Natural Gas Burner Assembly
(includes illus. nos. 1 through 8 and 10 through 32)
817208** 1 Liquid Propane Gas Burner Assembly
(includes illus. nos. 1 through 8 and 10 through 32)
882041** 1 CE Liquid Propane Conversion Kit 2 884265 1 Ignitor Flame-Probe (no wires) 3 152013 2 #6-32 Hex Nut 4 150309 5 #10-16 x 1/2” Hex Head TEK Crimptite Screw 5 141105 2 Large Tube Burner 6 150108 2 #8-32 x 1/2” Pan Head Machine Screw 7 887145 1 CE Direct Spark Ignition Module
(for models mfd. as of June 10, 2004)
887209 1 CE Direct Spark Ignition Module Kit
(for models mfd. prior to June 10, 2004) 8 151001 2 #8-32 Pal Nut 9 140819* 2 #30 Burner Orifice (natural gas)
140804* 2 #48 Burner Orifice (liquid propane gas) 10 141230 1 1/2” Manifold (2-port) 11 318700 1 Pipe Bracket (bent) 12 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 13 128933 1 1/2” 24 VAC CE Gas Valve (natural gas)
883255 1 1/2” 24 VAC CE Gas Valve (liquid propane gas) 14 141317 1 1/2” Bronze Union Elbow 15 142809 1 1/2” x 29-1/8” Pipe 16 318700 2 Pipe Bracket (bent) 17 150309 4 #10-16 x 1/2” Hex Head TEK Crimptite Screw 18 810029 1 Direct Spark Ignition Module Mounting Bracket
(for models mfd. as of June 10, 2004)
810031 1 Direct Spark Ignition Module Mounting Bracket
(for models mfd. prior to June 10, 2004) 19 142935 1 1/2” B.S.P.T. x 1/2” N.P.T. Transition Coupling 20 150005 2 #6-32 x 1/4” Round Head Machine Screw 21 154004 1 Twin Speed Nut 22 150300 9 #10-16 x 1/2” Hex Washer TEK Screw 23 802799 1 Sail Switch Top and Switch Bracket 24 150303 2 #4 x 3/4” Pan Head Machine Screw 25 122200 1 SPST Sail Switch (for micro models Only)
122404 1 SPDT Sail Switch (for dual timer models Only) 26 105500 1 Sail Switch Actuator Rod 27 319202 1 Sail Switch Damper (flat) 28 154002 1 1/8” Push-On Fastener 29 130201 1 330° Hi-Limit Thermostat 30 319704 1 Hi-Limit Mounting Bracket 31 152013 2 #6-32 Hex Nut 32 884279 1 High Voltage Gray Carbon Wire with Terminal
(for models mfd. as of June 10, 2004)
128919 1 High Voltage Red Wire
(for models mfd. prior to June 10, 2004)
33 830354 1 Direct Spark Ignition Control Wiring Harness
AD-30V CE Burner Assembly
* Consult factory for elevations over 2,000 feet. ** Burner orifices are not included and must be ordered separately. *** Contact ADC factory with serial number of dryer and country destination.
450438-5 www.amdry.com 41
Page 42
42 American Dryer Corporation 450438 - 5

AD-50V Burner Assembly

Page 43
AD-50V Burner Assembly
Illus. No. Part No. Qty. Description
1 141105 3 Large Tube Burner 2 151001 3 #8-32 Pal Nut 3 150108 3 #8-32 x 1/2” Pan Head Machine Screw 4* 140820 3 #29 Natural Gas Burner Orifice
140806 3 #46 Liquid Propane Burner Orifice 5 141232 1 1/2” Manifold (3-port) 6 150309 3 #10-16 x 1/2” Hex Head TEK Crimptite Screw 7 318714 1 Gas Valve Bracket (horizontal) 8 128927 1 1/2” 24 VAC Redundant (natural gas) Gas Valve
880960 1 1/2” 24 VAC Redundant (liquid propane gas) Gas Valve 9 884265 1 Ignitor Flame-Probe ONLY
882537 1 Flame-Probe Wire 10 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 11 810029 1 Direct Spark Ignition Module Mounting Bracket 12 887133 1 Direct Spark Ignition Module
(for models mfd. as of March 1, 2004)
887849 1 Direct Spark Ignition Module
(for models mfd. prior to March 1, 2004) 13 152013 2 #6-32 Hex Nut 14 141317 1 1/2” Bronze Union Elbow 15 142809 1 1/2” x 29-1/8” Black Nipple 16 830354 1 Direct Spark Ignition Control Wiring Harness 17 884279 1 High Voltage Gray Carbon Wire with Terminal
(for models mfd. as of March 1, 2004)
128919 1 High Voltage Red Wire
(for models mfd. prior to March 1, 2004) 18 817062*** 1 Direct Spark Ignition Burner Assembly Complete (natural gas)
(includes illus. nos. 1 through 3 and 5 through 18)
817063*** 1 Direct Spark Ignition Burner Assembly Complete (liquid propane gas)
(includes illus. nos. 1 through 3 and 5 through 18) — 850899 1 Burner Box ONLY — 882271* 1 ADG-50V Liquid Propane Conversion Kit (includes orifices)
883310** 1 Steam to Gas Transition Plate … Not Illustrated
* Consult factory for elevations over 2,000 feet. ** Needed when converting dryer from steam heat to gas heat. *** Burner orifices are not included and must be ordered separately.
450438-5 www.amdry.com 43
Page 44

AD-50V CE Burner Assembly

44 American Dryer Corporation 450438 - 5
Page 45
AD-50V CE Burner Assembly
Illus. No. Part No. Qty. Description
1 884265 1 Ignitor Flame-Probe ONLY 2 887145 1 CE Direct Spark Ignition Module
(for models mfd. as of June 10, 2004)
887209 1 CE Direct Spark Ignition Module
(for models mfd. prior to June 10, 2004) 3 810029 1 Direct Spark Ignition Module Mounting Bracket Assembly 4 150309 6 #10-16 x 1/2” Hex Head TEK Crimptite Screw 5 141105 3 Large Tube Burner 6 150108 3 #8-32 x 1/2” Pan Head Machine Screw 7 152013 2 #6-32 Hex Nut 8 151001 3 #8-32 Pal Nut 9 140819* 3 #30 Burner Orifice (natural gas)
140804* 3 #48 Burner Orifice (liquid propane gas) 10 141232 1 1/2” Manifold (3-port) 11 318700 3 Pipe Bracket (bent) 12 150300 9 #10-16 x 1/2” Hex Washer TEK Screw 13 128933 1 CE Gas Valve (natural gas)
883255 1 CE Gas Valve (liquid propane gas) 14 141317 1 1/2” Bronze Union Elbow 15 142809 1 1/2” x 29-1/8” Pipe 16 850899 1 Burner Box ONLY
817174** 1 Natural Gas Burner Assembly Complete
(includes illus. nos. 1 through 8, 10 through 28, and 30)
817207** 1 Liquid Propane Gas Burner Assembly Complete
(includes illus. nos. 1 through 8, 10 through 28, and 30) ––––––**** 1 Liquid Propane Conversion Kit 883310*** 1 Steam to Gas Interface Plate … Not Illustrated
17 142935 1 1/2” Coupling 18 319704 1 Hi-Limit Mounting Bracket 19 150001 2 #6-32 x 1/2” Round Head Machine Screw 20 151000 2 #6-32 Pal Nut 21 154004 1 Twin Speed Nut 22 130201 1 330° Hi-Limit Thermostat 23 802799 1 Sail Switch Top and Switch Bracket 24 150303 2 #4 x 3/4” Pan Head Machine Screw 25 122200 1 SPST Sail Switch (for micro models Only)
122404 1 SPDT Sail Switch (for dual timer models Only)
26 105500 1 Sail Switch Actuator Rod 27 319202 1 Sail Switch Damper (flat) 28 154002 1 1/8” Push-On Fastener 29 830354 1 Direct Spark Ignition Control Wiring Harness 30 884279 1 High Voltage Gray Carbon Wire with Terminal
(for models mfd. as of March 1, 2004) 128919 1 High Voltage Red Wire
(for models mfd. prior to March 1, 2004)
* Consult factory for elevations over 2,000 feet. ** Burner orifices are not included and must be ordered separately. *** Needed when converting from steam heat to gas heat. **** Contact ADC factory with serial number of dryer and country destination.
450438-5 www.amdry.com 45
Page 46

Electric Oven Assembly

46 American Dryer Corporation 450438 - 5
Page 47
Illus. No. Part No. Qty. Description
1 803007 1 Large Electric Oven Box ONLY
––––––* 1 Electric Oven Assembly Complete
2 ––––––* Electric Element 3 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 4 802800 1 Sail Switch Box with Bracket and Cover ONLY
802801 1 Sail Switch Box Assembly Complete
(includes illus. nos. 4 through 12) 802804 1 Sail Switch Box Assembly Complete (for dual timer CE models Only)
(includes illus. nos. 4 through 12)
5 154004 1 Twin Speed Nut 6 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 7 802799 1 Sail Switch Box Cover and Bracket ONLY 8 122200 1 SPST Sail Switch
122404 1 SPDT Sail Switch (for dual timer CE models Only)
9 150303 2 #4 x 3/4” Pan Head Machine Screw 10 105500 1 Sail Switch Actuator Rod 11 319202 1 Sail Switch Damper (flat) 12 154002 1 1/8” Push-On Fastener 13 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 14 803100 1 Electric Oven Front Cover 15 320611 1 Large Relay Box Cover 16 150301 2 #8-18 x 7/16” Phillips Pan Head TEK Screw 17 130400 1 290° Hi-Limit Thermostat 18 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 19 154001 2 #10-24 Speed Nut 20 121010 1 L-70 Ground Lug 21 152014 3 1/4-20 Free Spin Wash Nut 22 ––––––* 1 Oven Relay 23 150207 2 #10-24 x 1/2” Phillips Pan Head Machine Screw 24 120081 Internal Ceramic Insulator (2 per element) 25 120080 External Ceramic Insulator (2 per element) 26 152008 #10-32 Hex Nut (4 per element) 27 121011* Bus Bar (sold by the foot) 28 ––––––* Oven Wire 29 153009 #10 Star Washer (2 per element) 30 321301 1 Large Electric Oven Right Side Cover
883310** 1 Steam to Electric Transition Plate … Not Illustrated
Electric Oven Assembly
* Refer to Electric Oven Component Application Charts on p age 72 through p age 74. ** Needed when converting dryer from steam heat to electric heat.
450438-5 www.amdry.com 47
Page 48

Gas Burner Sail Switch / Hi-Limit Assemblies

48 American Dryer Corporation 450438 - 5
Page 49
Gas Burner Sail Switch / Hi-Limit Assemblies
Illus. No. Part No. Qty. Description
1 154004 1 Twin Speed Nut 2 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 3 802799 1 Sail Switch Box Cover and Bracket ONLY 4 150303 2 #4 x 3/4” Pan Head Machine Screw 5 122200 1 SPST Sail Switch
122404 1 SPDT Sail Switch (for dual timer CE models Only)
6 105500 1 Sail Switch Actuator Rod 7 319202 1 Sail Switch Damper (flat) 8 154002 1 1/8” Push-On Fastener 9 802800 1 Sail Switch Box with Cover and Bracket ONLY
802801 1 Sail Switch Assembly Complete
(includes illus. nos. 1 through 9) 802804 1 Sail Switch Assembly Complete (for dual timer CE models Only)
(includes illus. nos. 1 through 9)
10 –––––– 1 1/2” Pipe
(refer to Burner Assembly on page 38 through page 44 )
11 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 12 319704 1 Hi-Limit Mounting Bracket 13 151000 2 #6-32 Pal Nut 14 150001 2 #6-32 x 1/2” Phillips Round Head Machine Screw 15 130201 1 330° Hi-Limit Thermostat
450438-5 www.amdry.com 49
Page 50
50 American Dryer Corporation 450438 - 5

Phase 7 OPL Single-Phase (1ø) Rear Relay Panel Assembly

Page 51
Phase 7 OPL Single-Phase (1ø) Rear Relay Panel Assembly
Illus. No. Part No. Qty. Description
1 151000 2 #6-32 Pal Nut 2 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 3 150008 2 #6-32 x 1-1/4” Phillips Pan Head Machine Screw 4 120716 1 2-Position Terminal Block 5 322812 1 Rear Electric Mounting Plate ONLY
822796 1 Rear Electric Panel Assembly Complete – 115 Volt (for gas models Only)
(includes illus. nos. 1 through 14) 830153 1 Rear Electric Panel Assembly Complete – 115 Volt (for steam models Only)
(includes illus. nos. 1 through 14) 822798 1 Rear Electric Panel Assembly Complete – 208-240 Volt (for gas models Only)
(includes illus. nos. 1 through 14) 830273 1 Rear Electric Panel Assembly Complete – 208-240 Volt (for steam models Only)
(includes illus. nos. 1 through 14) 830131 1 Rear Electric Panel Assembly Complete – 208-240 Volt (for electric models Only)
(includes illus. nos. 1 through 14 and 16) 830426 1 Rear Electric Panel Assembly Complete – 380-416 Volt
(for electric models with 1ø motors Only)
(includes illus. nos. 1 through 14 and 16)
6 830151 1 Transformer Assembly – 115 Volt
822799 1 Transformer Assembly – 208-240 Volt (for gas and steam models Only) 822792 1 Transformer Assembly – 208-240 Volt (for electric models Only) 830141 1 Transformer Assembly – 380-416 Volt
7 136008 * Fuse Holder 8 136057 * 1/2-Amp (Slo-Blo) Fuse (for 208-416 volt models Only)
136049 * 3/4-Amp (Slo-Blo) Fuse (for 115 volt models Only)
9 150301 4 #8-18 x 7/16” Phillips Pan Head TEK Screw 10 150297 1 #10 x 1/2” Green Hex Washer TEK Screw 11 152004 1 5/16-18 Hex Nut 12 121010 1 L-70 Ground Lug 13 153002 1 5/16” Lock Washer 14 132495 1 3-Pole Contactor 15 121300 3 Open / Closed Bushing 16 131932 1 24V SPST Relay (for electric models Only)
* Quantity is 1 for 1 15v and 380-416v. Quantity is 2 for 208-240v.
450438-5 www.amdry.com 51
Page 52
52 American Dryer Corporation 450438 - 5

Phase 7 OPL 208-416V 3-Phase (3ø) Rear Relay Panel Assembly

Page 53
Phase 7 OPL 208-416V 3-Phase (3ø) Rear Relay Panel Assembly
Illus. No. Part No. Qty. Description
1 151000 2 #6-32 Pal Nut 2 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 3 150008 2 #6-32 x 1-1/4” Phillips Pan Head Machine Screw 4 120701 1 4-Position Terminal Block 5 322812 1 Rear Electric Mounting Plate ONLY
830154 1 Rear Electric Panel Assembly Complete – 208-240 Volt (for gas models Only)
(includes illus. nos. 1 through 14) 830322 1 Rear Electric Panel Assembly Complete – 208-240 Volt (for steam models Only)
(includes illus. nos. 1 through 14) 830157 1 Rear Electric Panel Assembly Complete – 208-240 Volt (for electric models Only)
(includes illus. nos. 1 through 14 and 16) ––––––* 1 Rear Electric Panel Assembly Complete – 380-416 Volt (for gas models Only)
(includes illus. nos. 1 through 14) 803834 1 Rear Electric Panel Assembly Complete – 380-416 Volt (for steam models Only)
(includes illus. nos. 1 through 14) 830140 1 Rear Electric Panel Assembly Complete – 380-416 Volt
(for electric models with 3ø motors Only)
(includes illus. nos. 1 through 14 and 16)
6 822799 1 Transformer Assembly – 208-240 Volt (for gas and steam models Only)
822792 1 Transformer Assembly – 208-240 Volt (for electric models Only) 822784 1 Transformer Assembly – 380-416 Volt (for gas and steam models Only) 830141 1 Transformer Assembly – 380-416 Volt (for electric models Only)
7 136008 1 or 2 Fuse Holder 8 136057 1 or 2 1/2-Amp (Slo-Blo) Fuse 9 150301 2 or 4 #8-18 x 7/16” Phillips Pan Head TEK Screw 10 150297 1 #10 x 1/2” Green Hex Washer TEK Screw 11 152004 1 5/16-18 Hex Nut 12 121010 1 L-70 Ground Lug 13 153002 1 5/16” Lock Washer 14 132495 1 3-Pole Contactor 15 121300 3 Open / Closed Bushing 16 131932 1 24V SPST Relay (for electric models Only)
* Not available at time of printing.
450438-5 www.amdry.com 53
Page 54

Phase 7 OPL 460-480V Rear Relay Panel Assembly

54 American Dryer Corporation 450438 - 5
Page 55
Phase 7 OPL 460-480V Rear Relay Panel Assembly
Illus. No. Part No. Qty. Description
1 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 2 150008 2 #6-32 x 1-1/4” Phillips Pan Head Machine Screw 3 120701 1 4-Position Terminal Block 4 135501 1 2-Pole 1-Amp Circuit Breaker 5 824221 1 Transformer Assembly – 460-480 Volt 6 120768 2 35 x 15mm Din Rail 7 120765 2 Standard End Bracket 8 150301 4 #8-18 x 7/16” Phillips Pan Head TEK Screw 9 150297 2 #10 x 1/2” Green Hex Washer TEK Screw 10 152004 1 5/16-18 Hex Nut 11 121010 2 L-70 Ground Lug 12 153002 1 5/16” Lock Washer 13 132495 1 3-Pole Contactor 14 322812 1 Rear Electric Mounting Plate ONLY
830263 1 Rear Electric Panel Assembly Complete – 460-480 Volt (for gas models Only)
(includes illus. nos. 1 through 15 and 17) 830137 1 Rear Electric Panel Assembly Complete – 460-480 Volt (for steam models Only)
(includes illus. nos. 1 through 15 and 17) 830199 1 Rear Electric Panel Assembly Complete – 460-480 Volt (for electric models Only)
(includes illus. nos. 1 through 17)
15 151000 2 #6-32 Pal Nut 16 131932 1 24V SPST Relay (for electric models Only) 17 112075 1 Ground Label
450438-5 www.amdry.com 55
Page 56

Phase 7 OPL 208-416V Reversing Rear Relay Panel Assembly

56 American Dryer Corporation 450438 - 5
Page 57
Phase 7 OPL 208-416V Reversing Rear Relay Panel Assembly
Illus. No. Part No. Qty. Description
1 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 2 150008 2 #6-32 x 1-1/4” Phillips Pan Head Machine Screw 3 120701 1 4-Position Terminal Block 4 132497 1 3-Pole Reversing Contactor 5 822799 1 Transformer Assembly – 208-240 Volt (for gas and steam models Only)
822792 1 Transformer Assembly – 208-240 Volt (for electric models Only) 822784 1 Transformer Assembly – 380-416 Volt
6 136008 1 or 2 Fuse Holder 7 136057 1 or 2 1/2-Amp (Slo-Blo) Fuse 8 150301 2 or 4 #8-18 x 7/16” Phillips Pan Head TEK Screw 9 150297 2 #10 x 1/2” Green Hex Washer TEK Screw 10 152004 1 5/16-18 Hex Nut 11 121010 2 L-70 Ground Lug 12 153002 1 5/16” Lock Washer 13 132495 1 3-Pole Contactor 14 322812 1 Rear Electric Mounting Plate ONLY
822771 1 Rear Electric Panel Assembly Complete – 208-240 Volt (for gas models Only)
(includes illus. nos. 1 through 16) 830167 1 Rear Electric Panel Assembly Complete – 208-240 Volt (for steam models Only)
(includes illus. nos. 1 through 16) 822789 1 Rear Electric Panel Assembly Complete – 208-240 Volt (for electric models Only)
(includes illus. nos. 1 through 17) 822783 1 Rear Electric Panel Assembly Complete – 380-416 Volt (for gas models Only)
(includes illus. nos. 1 through 16) 830117 1 Rear Electric Panel Assembly Complete – 380-416 Volt (for steam models Only)
(includes illus. nos. 1 through 16) 818397 1 Rear Electric Panel Assembly Complete – 380-416 Volt (for electric models Only)
(includes illus. nos. 1 through 17)
15 151000 2 #6-32 Pal Nut 16 120765 1 Standard End Bracket 17 131932 1 24V SPST Relay (for electric models Only)
450438-5 www.amdry.com 57
Page 58

Phase 7 OPL 460-480V Reversing Rear Relay Panel Assembly

58 American Dryer Corporation 450438 - 5
Page 59
Phase 7 OPL 460-480V Reversing Rear Relay Panel Assembly
Illus. No. Part No. Qty. Description
1 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 2 150008 2 #6-32 x 1-1/4” Phillips Pan Head Machine Screw 3 120701 1 4-Position Terminal Block 4 135501 1 2-Pole 1-Amp Circuit Breaker 5 824221 1 Transformer Assembly – 460-480 Volt 6 120768 2 35 x 15mm Din Rail 7 120765 2 Standard End Bracket 8 150301 4 #8-18 x 7/16” Phillips Pan Head TEK Screw 9 150297 2 #10 x 1/2” Green Hex Washer TEK Screw 10 152004 1 5/16-18 Hex Nut 11 121010 2 L-70 Ground Lug 12 153002 1 5/16” Lock Washer 13 132495 1 3-Pole Contactor 14 322812 1 Rear Electric Mounting Plate ONLY
830147 1 Rear Electric Panel Assembly Complete – 460-480 Volt (for gas models Only)
(includes illus. nos. 1 through 17) 830103 1 Rear Electric Panel Assembly Complete – 460-480 Volt (for steam models Only)
(includes illus. nos. 1 through 17) 824371 1 Rear Electric Panel Assembly Complete – 460-480 Volt (for electric models Only)
(includes illus. nos. 1 through 18)
15 151000 2 #6-32 Pal Nut 16 132497 1 3-Pole Reversing Contactor 17 112075 1 Ground Label 18 131932 1 24V SPST Relay (for electric models Only)
450438-5 www.amdry.com 59
Page 60

Dual Timer Single-Phase (1ø) Relay Panel Assembly

60 American Dryer Corporation 450438 - 5
Page 61
Dual Timer Single-Phase (1ø) Relay Panel Assembly
Illus. No. Part No. Qty. Description
1 151000 2 #6-32 Pal Nut 2 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 3 150008 2 #6-32 x 1-1/4” Phillips Pan Head Machine Screw 4 120716 1 2-Position Terminal Block 5 322817 1 Rear Electric Mounting Plate ONLY
882662 1 Rear Electric Panel Assembly Complete – 120 Volt
(includes illus. nos. 1 through 14) 882663 1 Rear Electric Panel Assembly Complete – 208-240 Volt (for gas and steam models Only)
(includes illus. nos. 1 through 14) 818395 1 Rear Electric Panel Assembly Complete – 208-240 Volt
(for electric models mfd. with single-phase [1ø] motor Only)
(includes illus. nos. 1 through 14) 882667 1 Rear Electric Panel Assembly Complete – 380-416 Volt
(for electric models mfd. with single-phase [1ø] motor Only)
(includes illus. nos. 1 through 14)
6 882652 1 Transformer Assembly – 120 Volt
882653 1 Transformer Assembly – 208-240 Volt (for gas and steam models Only) 818396 1 Transformer Assembly – 208-240 Volt (for electric models Only) 882654 1 Transformer Assembly – 380-416 Volt
7 136008 * Fuse Holder 8 136049 * 3/4-Amp (Slo-Blo) Fuse – 120 Volt
136057 * 1/2-Amp (Slo-Blo) Fuse – 208-416 Volt
9 150301 * #8-18 x 7/16” Phillips Pan Head TEK Screw 10 150297 1 #10 x 1/2” Green Hex Washer TEK Screw 11 152004 1 5/16-18 Hex Nut 12 121010 1 L-70 Ground Lug 13 153002 1 5/16” Lock Washer 14 132459 1 3-Pole Contactor 15 121300 3 Open / Closed Bushing
* Quantity is 1 for 1 15v and 380-416v. Quantity is 2 for 208-240v.
450438-5 www.amdry.com 61
Page 62
62 American Dryer Corporation 450438 - 5

Dual Timer 208-416V 3-Phase (3ø) Relay Panel Assembly

Page 63
Dual Timer 208-416V 3-Phase (3ø) Relay Panel Assembly
Illus. No. Part No. Qty. Description
1 151000 2 #6-32 Pal Nut 2 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 3 150008 2 #6-32 x 1-1/4” Phillips Pan Head Machine Screw 4 120701 1 4-Position Terminal Block (for models mfd. with 3-phase [3ø] motors) 5 322817 1 Rear Electric Mounting Plate ONLY
882664 1 Rear Electric Panel Assembly Complete – 208-240 Volt (for gas and steam models Only)
(includes illus. nos. 1 through 14) 818400 1 Rear Electric Panel Assembly – 208-240 Volt (for electric models Only)
(includes illus. nos. 1 through 14) 882665 1 Rear Electric Panel Assembly Complete – 380-416 Volt (for gas and steam models Only)
(includes illus. nos. 1 through 14)
6 882653 1 Transformer Assembly – 208-240 Volt (for gas and steam models Only)
818396 1 Transformer Assembly – 208-240 Volt (for electric models Only) 882654 1 Transformer Assembly – 380-416 Volt
7 136008 * Fuse Holder 8 136057 * 1/2-Amp (Slo-Blo) Fuse 9 150301 * #8-18 x 7/16” Phillips Pan Head TEK Screw 10 150297 1 #10 x 1/2” Green Hex Washer TEK Screw 11 152004 1 5/16-18 Hex Nut 12 121010 1 L-70 Ground Lug 13 153002 1 5/16” Lock Washer 14 132459 1 3-Pole Contactor 15 121300 3 Open / Closed Bushing
* Quantity is 1 for 380-416v and 2 for 208-240v .
450438-5 www.amdry.com 63
Page 64

Dual Timer 460-480V Electric Relay Panel Assembly

Illus. No. Part No. Qty. Description
1 150009 2 #6-32 x 1-1/2” Phillips Pan Head Machine Screw 2 120701 1 4-Position Terminal Block 3 824161 1 Transformer Assembly 4 135501 1 2-Pole 1-Amp Circuit Breaker 5 120768 2 35 x 15mm Din Rail 6 150301 4 #8-18 x 7/16” Phillips Pan Head TEK Screw 7 150297 1 #10 x 1/2” Green Hex Washer TEK Screw 8 152004 1 5/16-18 Hex Nut 9 121010 1 L-70 Ground Lug 10 153002 1 5/16” Lock Washer 11 132459 1 24 VAC 3-Pole Contactor 12 322817 1 Mounting Plate ONLY
830262 1 Rear Panel Assembly Complete
(includes illus. nos. 1 through 14) 13 151000 2 #6-32 Pal Nut 14 120765 4 End Stop 15 121300 3 Open / Closed Bushing
64 American Dryer Corporation 450438 - 5
Page 65

Dual Timer 208-416V Reversing Relay Panel Assembly

Illus. No. Part No. Qty. Description
1 150300 2 #10-16 x 1/2” Hex Washer TEK Screw 2 150008 2 #6-32 x 1-1/4” Phillips Pan Head Machine Screw 3 120701 1 4-Position Terminal Block 4 132458 1 3-Pole Reversing Contactor 5 882653 1 Transformer Assembly – 208-240 Volt (for gas and steam models Only)
825428 1 Transformer Assembly – 208-240 Volt (for electric models Only)
882654 1 Transformer Assembly – 380-416 Volt 6 136008 * Fuse Holder 7 136057 * 1/2-Amp (Slo-Blo) Fuse 8 150301 * #8-18 x 7/16” Phillips Pan Head TEK Screw 9 150297 2 #10 x 1/2” Green Hex Washer TEK Screw 10 152004 1 5/16-18 Hex Nut 11 121010 1 L-70 Ground Lug 12 153002 1 5/16” Lock Washer 13 132459 1 3-Pole Contactor 14 322812 1 Rear Electric Mounting Plate ONLY
882673 1 Rear Electric Panel Assembly Complete – 208-240 Volt (for gas and steam models Only)
(includes illus. nos. 1 through 16)
883335 1 Rear Electric Panel Assembly Complete – 208-240 Volt (for electric models Only)
(includes illus. nos. 1 through 16)
882676 1 Rear Electric Panel Assembly Complete – 380-416 Volt
(includes illus. nos. 1 through 16) 15 151000 2 #6-32 Pal Nut 16 120765 1 Standard End Bracket
* Quantity is 2 for 208-240v and 1 for 380-416v .
450438-5 www.amdry.com 65
Page 66

Dual Timer 460-480V Reversing Relay Panel Assembly

Illus. No. Part No. Qty. Description
1 132458 1 24 VAC Reversing Contactor 2 150297 1 #10 x 1/2” Green Hex Washer TEK Screw 3 121010 1 L-70 Ground Lug 4 152004 1 5/16-18 Hex Nut 5 153002 1 5/16” Lock Washer 6 132459 1 24 VAC 3-Pole Blower Contactor 7 150301 4 #8-18 x 7/16” Phillips Pan Head TEK Screw 8 824161 1 Transformer Assembly 9 120765 2 Standard End Bracket 10 322817 1 Mounting Plate ONLY
824412 1 Rear Electric Panel Assembly Complete
(includes illus. nos. 1 through 16) 11 151000 2 #6-32 Pal Nut 12 150009 2 #6-32 x 1-1/2” Phillips Pan Head Machine Screw 13 120701 1 4-Position Terminal Block 14 135501 1 2-Pole 1-Amp Circuit Breaker 15 120768 2 35 x 15mm Din Rail (sold by the inch) 16 112068 1 3-Phase (3ø) Power Input Label 17 121300 3 Open / Closed Bushing
66 American Dryer Corporation 450438 - 5
Page 67

AD-30V Steam Coil / Air-Operated Steam Damper Assembly

Illus. No. Part No. Qty. Description
1 165008 1 Steam Coil 2 153002 6 5/16” Lock Washer 3 152004 6 5/16-18 Hex Nut 4 152002 4 1/4-20 Hex Nut 5 153007 4 1/4” Lock Washer 6 820321 2 Steam Damper Hinge Assembly 7 803416 1 Steam Damper Assembly
(includes illus. nos. 7, 10, and 11) 8 153007 4 1/4” Lock Washer 9 152002 4 1/4-20 Hex Nut 10 115995 60 Steam Damper Gasket (sold by the inch) 11 102350 1 Steam Damper Foam (68-1/2” length) 12 151006 1 5/16-24 Stainless Steel Acorn Nut 13 152051 1 5/16-24 Right Hand Jam Nut 14 100495 1 1-1/16” Dia. x 3” Stroke Piston 15 323365 2 Left and Right Piston Support 16 152002 2 1/4-20 Hex Nut 17 153007 2 1/4” Lock Washer 18 100472 1 1/4” x 1/8” Connector 19 143110 1 1/4” Tubing (sold by the foot) 20 100472 1 1/4” x 1/8” Connector 21 100496 1 1/8” Needle Valve 22 143238 1 1/8” Close Nipple 23 100498 1 3-Way Micro Valve – 24 VAC 24 150002 2 #6-32 x 1” Slotted Machine Screw 25 153010 2 #6 Star Washer 26 152000 2 #6-32 Hex Nut 27 330987 1 Micro Valve Support Bracket 28 152002 2 1/4-20 Hex Nut 29 153007 2 1/4” Lock Washer 30 100520 1 1/8” N.P.T. Silencer (muffler)
450438-5 www.amdry.com 67
Page 68

AD-50V Steam Coil / Air-Operated Steam Damper Assembly

Illus. No. Part No. Qty. Description
1 165011 1 Steam Coil 2 153002 6 5/16” Lock Washer 3 152004 6 5/16-18 Hex Nut 4 152002 4 1/4-20 Hex Nut 5 153007 4 1/4” Lock Washer 6 820321 2 Steam Damper Hinge Assembly 7 850260 1 Steam Damper Assembly
(includes illus. nos. 7, 10, and 11) 8 153007 4 1/4” Lock Washer 9 152002 4 1/4-20 Hex Nut 10 115995 60 Steam Damper Gasket (sold by the inch) 11 102350 1 Steam Damper Foam (68-1/2” length) 12 151006 1 5/16-24 Stainless Steel Acorn Nut 13 152051 1 5/16-24 Right Hand Jam Nut 14 100495 1 1-1/16” x 3” Stroke Piston 15 323365 2 Left and Right Piston Support 16 152002 2 1/4-20 Hex Nut 17 153007 2 1/4” Lock Washer 18 143163 1 1/4” x 1/8” Connector 19 143110 1 1/4” Tubing (sold by the foot) 20 143163 1 1/4” x 1/8” Connector 21 100496 1 1/8” Needle Valve 22 143238 1 1/8” Close Nipple 23 100498 1 3-Way Micro Valve – 24 VAC 24 150002 2 #6-32 x 1” Slotted Machine Screw 25 153010 2 #6 Star Washer 26 152000 2 #6-32 Hex Nut 27 330987 1 Micro Valve Support Bracket 28 152002 2 1/4-20 Hex Nut 29 153007 2 1/4” Lock Washer 30 100520 1 1/8” N.P.T. Silencer (muffler)
68 American Dryer Corporation 450438 - 5
Page 69

Fire Suppression System Assemblies

Illus. No. Part No. Qty. Description
1 165114 1 Fire Suppression System Solenoid Valve 24V 50/60 Hz 2 143220 1 3/8” F.P.T. Brass Tee 3 143251 1 3/8” M.P.T. Brass Plug 4 143208 2 3/8” Comp x 3/8” M.P.T. Brass Connector 5 143099 6' 3/8” OD x 0.035 Wall Copper Tubing (sold by the foot) 6 311588 1 Sprinkler Head Mounting Plate 7 143303 1 3/8” N.P.T. Brass Locknut 8 143155 1 3/8” Brass Elbow 90° 9 150430 2 #10 x 1/2” Self-Drilling Screw 10 150301 2 #8-18 x 7/16” TEK Screw 11 143581 1 3 GPM 3/8” F.P.T. Spray Nozzle 12 143025 1 3/8 x 3/4 NH 60 Hz
143177 3/4 M.P.T. x 3/8 Adapt 50 Hz 13 824081 1 R.C. Network Assembly 14 143241 1 3/8” x Close Brass Nipple 15 143315 1 3/8” M.N.P.T. x 1/8” F.N.P.T. Brass Bushing 16 136987 1 Water Jet Pressure Switch
(for models mfd. as of December 1, 2003)
17 822752 1 Fire Suppression System Temperature Probe Assembly
(includes illus. nos. 17 through 19 and 21) 18 154007 2 Push-On Fastener 19 390390 1 Sensor Bracket ONLY 20 150301 2 #8-18 x 7/16” Phillips Pan Head TEK Screw 21 122647 1 Connector ONLY (does not include terminals)
450438-5 www.amdry.com 69
Page 70

AD-30V Outer Top / Back Guard Assemblies

Illus. No. Part No. Qty. Description
1 322809 1 Back Electrical Box Cover 2 150301 4 #8-18 x 7/16” Phillips Pan Head TEK Screw 3* 314424 1 Top Back Panel / Guard (gas Only)
314422 1 Top Back Panel / Guard (electric Only)
322007 1 Interface Plate (gas and electric Only) … Not Illustrated 4 150301 7 #8-18 x 7/16” Phillips Pan Head TEK Screw 5 150300 10 #10-16 x 1/2” Hex Washer TEK Screw 6* 322015 1 Outer Top (gas and electric Only) 7 322082 1 Bottom Back Guard / Panel 8 150301 13 #8-18 x 7/16” Phillips Pan Head TEK Screw 9 103500 4 Leveling Leg
* There is no outer top or top back guard on steam models.
70 American Dryer Corporation 450438 - 5
Page 71

AD-50V Outer Top / Back Guard Assemblies

Illus. No. Part No. Qty. Description
1 322809 1 Back Electrical Box Cover 2 150301 4 #8-18 x 7/16” Phillips Pan Head TEK Screw 3* 314424 1 Top Back Panel / Guard (gas Only)
314422 1 Top Back Panel / Guard (electric Only)
322022 1 Interface Plate (gas and electric Only) … Not Illustrated 4 150301 7 #8-18 x 7/16” Phillips Pan Head TEK Screw 5 150300 10 #10-16 x 1/2” Hex Washer TEK Screw 6* 312533 1 Outer Top (gas and electric Only) 7 322082 1 Bottom Back Guard / Panel 8 150301 13 #8-18 x 7/16” Phillips Pan Head TEK Screw 9 103500 4 Leveling Leg
* There is no outer top or top back guard on steam models.
450438-5 www.amdry.com 71
Page 72
72 American Dryer Corporation 450438 - 5

AD-30V Oven Component Application Chart

nevO
WkegatloVesahPeriW
428034ro3——64 01002114#50403810101211—363131 420433 —64 11002116#4040381010121136APD963131 42084/064ø34ro3——64 11002118#2040381010121233APD253131 028012 —54 01002112#26173810101212—263131 020412 —54 11002112#48338810101212—263131
* When ordering oven assembly complete, specify 3- or 4-wire when applicable.
ylbmessA *
.oNtraP
.ytQWk.oNtraP.ytQeziS.oNtraP.ytQ.oNtraP.oN.taC.oNtraP
tnemelE
eriWnevO
lanimreTpmirChtiw
guLlanimreT
raBsuB
.oNtraP
110121
yaleRnevO
Page 73
450438-5 www.amdry.com 73

AD-50V Micro Electric Oven Component Application Chart

nevO
WkegatloVesahPeriW
038034ro30605386521002114#66032810101211—263131 030433 4213386531002114#50403810101211—363131 03084/064ø34ro32226286531002118#2040381010121134APD753131
* When ordering oven assembly complete, specify 3- or 4-wire when applicable.
ylbmessA *
.oNtraP
.ytQWk.oNtraP.ytQeziS.oNtraP.ytQ.oNtraP.oN.taC.oNtraP
tnemelE
eriWnevO
lanimreTpmirChtiw
guLlanimreT
raBsuB
.oNtraP
110121
yaleRnevO
Page 74
74 American Dryer Corporation 450438 - 5

AD-50V Dual Timer Electric Oven Component Application Chart

Oven
kW Voltage Phase Wire
30 208 3 or 4 825 37 6 6 5 120012 1 #4 882566 1 121010 1 DPA93 131358 30 240 3 816129 6 5 120013 1 #4 882566 1 121010 1 DPA73 131376 30 460/480 3 o r 4 824162 6 5 120013 1 #8 882572 1 12 1 010 1 D PA43 131357
* When ordering oven assembly complete, specify 3- or 4-wire when applicable.
Assembly *
Part No.
Element
Qty. kW Part No . Qty. Si ze Par t No. Qty. Par t No. Ca t. No. Par t No.
Oven W ire
with C r imp Term in a l
Terminal Lug
Bus Bar Part No.
121011
Oven R elay
Page 75
Part No. Description
112280 “Clean Lint Screen” Label 114001 “CAUTION Exhaust / Lint Screen” Label 114006 “WARNING – Fire Hazards” Label 114125 Warning Label (5 languages) 114521 “Phase 7 OPL Program Location Summary” Label 120800 1/4” In-Line Connector 120802 Red Butt Connector 120902 #74B Wire Nut 120903 Crimp-On Wire Nut 121499 5-1/2” Harness Tie 121500 8” Harness Tie 404502 White Brush-In-Cap Bottle Touch-Up Paint (0.6 oz. bottle)
Additional Parts Available
404513 Wrinkle Blue Brush-In-Cap Bottle Touch-Up Paint (0.6 oz. bottle) 404516 Ivory Brush-In-Cap Bottle Touch-Up Paint (0.6 oz. bottle) 882206 CD Rom (ADC Publications)
Part No. Description
122804 Manometer (hydro gauge) for Measuring Gas Pressure 882458 Tumbler Puller (for removal of rear tumbler bearing) 140929 1/8” Dia. Pitot Tube (required for Magnehelic below) 168203 0 - 2.0 in WC Magnehelic Gauge (for taking exhaust static pressure readings).
Does not include case or Pitot tube. Must be purchased separately.
883830 36E Gas Valve Tail Piece Removal Tool 883204 Fabricated Fan Puller
Tools Available
450438-5 www.amdry.com 75
Page 76
ADC Part No. 450438 5 - 08/26/08 - 0
Loading...