American Dryer Corp AD-285 User Manual

AD-285 Parts Manual

1987 thru 1991

American Dryer Corporation

88 Currant Road

Fall River, MA 02720-4781

T elephone: [phone] / Fax: [phone]

e-mail: [e-mail]

www .amdry.com

ADC Part No. 450085

Retain This Manual In A Safe Place For Future Reference

American Dryer Corporation products embody advanced concepts in engineering, design, and safety. If this product is

properly maintained, it will provide many years of safe, efficient, and trouble free operation.

ONLY qualified technicians should service this equipment.

OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation manual included with
the dryer.

The following “FOR YOUR SAFETY” caution must be posted near the dryer in a prominent location.

FOR YOUR SAFETY

Do not store or use gasoline or
other flammable vapors and
liquids in the vicinity of this or
any other appliance.

W e have tried to make this manual as complete as possible and hope you will find it useful. ADC reserves the right to make
changes from time to time, without notice or obligation, in prices, specifications, colors, and material, and to change or
discontinue models.

POUR VOTRE SÉCURITÉ

Ne pas entreposer ni utiliser d’essence
ni d’autres vapeurs ou liquides
inflammables à proximité de cet
appareil ou de tout autre appareil.

Important

For your convenience, log the following information:

DA TE OF PURCHASE ____________________________ MODEL NO. __________________________________________

RESELLER’S NAME _______________________________________________________________________________________

Serial Number(s) ________________________________________________________________________________________

________________________________________________________________________________________

AD-285

________________________________________________________________________________________

Replacement parts can be obtained from your reseller or the ADC factory. When ordering replacement parts from the factory ,
you can F AX your order to ADC at [phone] or telephone your order directly to the ADC Parts Department at (508)
678-9000. Please specify the dryer model number and serial number in addition to the description and part number, so that
your order is processed accurately and promptly.

The illustrations on the following pages may not depict your particular dryer exactly. The illustrations are a composite of the
various dryer models. Be sure to check the descriptions of the parts thoroughly before ordering.

“IMPORT ANT NOTE TO PURCHASER”

Information must be obtained from your local gas supplier on the instructions
to be followed if the user smells gas. These instructions must be posted in a
prominent location near the dryer.

Table of Contents

High Security Control Door Assembly..................................................................................................... 3

Phase 4.1 Single Coin Microprocessor Control Panel Assembly

For Direct Spark Ignition (DSI) Models Only..................................................................................... 4

Phase 4.1 Single Coin Microprocessor Control Box Assembly

For Direct Spark Ignition (DSI) Models Only...................................................................................... 5

Phase 4.1 Dual Coin Microprocessor Control Panel Assembly

For Direct Spark Ignition (DSI) Models Only..................................................................................... 6

Phase 4.1 Dual Coin Microprocessor Control Box Assembly

For Direct Spark Ignition (DSI) Models Only...................................................................................... 7

Phase 4 Single Coin Microprocessor Control Panel/Box Assemblies

For Glo-Bar® Ignition Models Only................................................................................................. 8, 9

Phase 4 Dual Coin Microprocessor Control Panel/Box Assemblies

For Glo-Bar® Ignition Models Only............................................................................................. 10, 11

Phase 4 OPL Microprocessor Control Panel Assembly

For Direct Spark Ignition (DSI) Models Only.................................................................................... 12

Phase 4 OPL Microprocessor Control Box Assembly

For Direct Spark Ignition (DSI) Models Only.................................................................................... 13

Phase 3 OPL Microprocessor Control Panel Assembly

For Glo-Bar® Ignition Models Only................................................................................................... 14

Phase 3 OPL Microprocessor Control Box Assembly

For Glo-Bar® Ignition Models Only................................................................................................... 15

Dual Timer Control Panel/Box Assemblies

For Direct Spark Ignition (DSI) Models Only.............................................................................. 16, 17

Dual Timer Control Panel/Box Assemblies

For Glo-Bar® Ignition Models Only............................................................................................. 18, 19

Non-Microprocessor Coin Control Panel/Box Assemblies

For Direct Spark Ignition (DSI) and Glo-Bar® Ignition Models .................................................... 20, 21

Coin Meter Replacement Parts ............................................................................................................. 22

Coin V ault Assembly ............................................................................................................................. 23

Front Panel Assembly

Latch-T ype....................................................................................................................................... 24

Front Panel Assembly

Magnet-T ype.................................................................................................................................... 25

Main Door Assembly

Latch-T ype....................................................................................................................................... 26

Main Door Assembly

Magnet-T ype.................................................................................................................................... 27

Main Door Switch Assembly

N.S. Series....................................................................................................................................... 28

Main Door Switch Assembly

Plunger-T ype.................................................................................................................................. 29

Drop Lint Door Assembly ..................................................................................................................... 30

Lint Trap Assembly ............................................................................................................................... 31

Basket (Tumbler)/Support Assembly

T apered Rib

For Models Mfd. as of April 18, 1991 ............................................................................................32

Basket (Tumbler)/Support Assembly

Standard Rib

For Models Mfd. prior to April 18, 1991 ........................................................................................ 33

Basket (Tumbler) Bearing Assembly ................................................................................................ 34, 35

Idler Bearing Assembly ................................................................................................................... 36, 37

T otally Enclosed, Fan-Cooled (T .E.F .C.) Motor Mount Assembly

For 60 Hz Models with T apered Ribs Only ............................................................................... 38, 39

T otally Enclosed, Fan-Cooled (T .E.F .C.) Motor Mount Assembly

For 60 Hz Models with Standard Ribs Only .............................................................................. 40, 41

T otally Enclosed, Fan-Cooled (T .E.F .C.) Motor Mount Assembly

For 50 Hz Models with T apered and Standard Ribs .................................................................. 42, 43

Sensor Bracket Assemblies............................................................................................................. 44, 45

Direct Spark Ignition (DSI) Burner Assembly .................................................................................. 46, 47

Hi/Lo Microprocessor Burner Assembly

For Glo-Bar

®

Ignition Models Only........................................................................................... 48, 49

Non-Microprocessor (Standard) Burner Assembly

For Glo-Bar® Ignition Models Only........................................................................................... 50, 51

Sail Switch/Hi-Limit Assembly ........................................................................................................ 52, 53

Replacement Coil For 3/8” Hi/Lo Gas V alve

For Glo-Bar® Ignition Models Only................................................................................................. 54

Replacement Coil For 3/8” Non-Hi/Lo Gas V alve

For Glo-Bar® Ignition Models Only................................................................................................. 55

3-Phase (3Ø) Motor, Electric Relay Panel Assembly

T elemecanique (208/230 V AC Controls)......................................................................................... 56

3-Phase (3Ø) Motor, Electric Relay Panel Assembly

Furnas (208/230 VAC Controls)..................................................................................................... 57

Control/Heat Step Down Transformer

For Glo-Bar® Ignition Models Only................................................................................................. 58

Outer T op/Back Guard Assembly ......................................................................................................... 59

Additional Parts A vailable ..................................................................................................................... 60

Microprocessor Coin Acceptor Listing.................................................................................................. 61

Wiring Diagrams ..............................................................................................................................62-83

High Security Control Door Assembly

Illus. No. Part No. Qty. Description

1 160015 1 High Security MK-100 Lock Assembly ONLY with Key

160104 1 MK-100 Key ONLY
160017 1 Special Dummy Lock (noncoin models Only)

2 160016 1 Lock Cam ONLY
3 112350 1 ADC Logo ONLY

870011 1 Logo Double Tape Kit

4 800019* 1 High Security Control Door Assembly Complete

(includes illus. nos. 4 through 7)

800143 1 Stainless Steel High Security Control Door Assembly Complete

(includes illus. nos. 4 through 7)
5 180203 1 Top Trim Strip with Lock Hole (28-3/8” length)
6 102307 3 Trim Bumper Gasket (sold by the foot)
7 150201 4 #10-32 x 1/4” Phillips Round Head Machine Screw
8 150415 4 #10-16 x 1/2” Phillips Round Head Crimptite Screw
9 102600 1 Control Door Support Rod Catch
10 102601 1 Control Door Rod Retainer Clip
11 102503 1 Control Door Support Rod

* Specify color when ordering.

450085-8 Telephone: [phone] / www.amdry.com 3

Phase 4.1 Single Coin Microprocessor Control Panel Assembly

For Direct Spark Ignition (DSI) Models ONL Y

Illus. No. Part No. Qty. Description

1 112526 1 Coin Keyboard Label Assembly
2 865098 1 Phase 4.1 Coin Control Panel Assembly

(includes illus. nos. 1, 2, and 4 through 6)

865099 1 Phase 4.1 Coin Control Panel Assembly with Battery Option

(includes illus. nos. 1, 2, and 4 through 6)
800040 1 Microprocessor Coin Control Panel ONLY
800039 1 Microprocessor Coin Control Panel ONLY with Battery Bracket

3 150415 1 #10-16 x 1/2” Phillips Round Head Crimptite Screw
4 137130 1 Phase 4.1 Coin Microprocessor Controller ONLY

137131 1 Phase 4.1 Coin Microprocessor Controller ONLY with Battery Clip

5 152001 4 #8-32 Hex Nut
6 153012 4 #8 S tar Washer
7 -------- 1 Microprocessor Single Coin Acceptor with Optical Switch

(refer to Microprocessor Coin Acceptor Listing on page 61)

8 137056 1 Optical Switch ONLY
9 137023 1 Optical Switch Connector ONLY
10 137021 3 Microprocessor Socket ONLY

865050 1 Single Coin Optical Switch Harness

--- 122800 1 Microprocessor (female) Pin Extraction Tool...Not Illustrated

IMPORTANT: Check label on computer chip to verify correct part number for microprocessor controller.

4 American Dryer Corporation 450 085- 8

Phase 4.1 Single Coin Microprocessor Control Box Assembly

For Direct Spark Ignition (DSI) Models ONL Y

Illus. No. Part No. Qty. Description

1 137021 1 2 Microprocessor Socket ONLY
2 137020 1 15-Pin Microprocessor Connector ONLY

122800 1 Microprocessor (female) Pin Extraction Tool...Not Illustrated
3 150315 1 #6 x 3/8” Phillips Pan Head Screw
4 137022 1 15-Pin Strain Relief ONLY
5 137013 4 Nylon Standoff
6 137151 1 Motor Control Solid State Relay Board, 1 HP, 125 VAC - 250 VAC 1Ø

50/60 Hz

7 136057 * 1/2-amp (Slo-Blo) Fuse ONLY

136052 * 4-amp Fuse ONLY
8 150300 2 #10-16 x 1/2” Hex Washer TEK Screw
9 141403 1 Direct Spark Ignition (DSI) 24 VAC Transformer (for gas models Only)
10 150002 2 #6-32 x 1” Round Head Machine Screw
11 120715 1 30-Position T erminal Block
12 151000 2 #6-32 Pal Nut
13 136057 * 1/2-amp (Slo-Blo) Fuse ONLY
14 150301 * #8-18 x 7/16” Phillips Pan Head TEK Screw
15 136008 1 Fuse Block/Strip ONLY

* As required.

450085-8 Telephone: [phone] / www.amdry.com 5

Phase 4.1 Dual Coin Micr opr ocessor Contr ol Panel Assembly

For Direct Spark Ignition (DSI) Models ONL Y

Illus. No. Part No. Qty. Description

1 112526 1 Coin Keyboard Label Assembly
2 865098 1 Phase 4.1 Coin Control Panel Assembly

(includes illus. nos. 1, 2, and 4 through 6)

865099 1 Phase 4.1 Coin Control Panel Assembly with Battery Option

(includes illus. nos. 1, 2, and 4 through 6)
800040 1 Microprocessor Coin Control Panel ONLY
800039 1 Microprocessor Coin Control Panel ONLY with Battery Bracket

3 150415 1 #10-16 x 1/2” Phillips Round Head Crimptite Screw
4 137130 1 Phase 4.1 Coin Microprocessor Controller ONLY

137131 1 Phase 4.1 Coin Microprocessor Controller ONLY with Battery Clip

5 152001 4 #8-32 Hex Nut
6 153012 4 #8 S tar Washer
7 -------- 1 Microprocessor Dual Coin Acceptor with Optical Switch

(refer to Microprocessor Coin Acceptor Listing on page 61)

8 137056 2 Optical Switch ONLY
9 137023 2 Optical Switch Connector ONLY
10 137021 6 Microprocessor Socket ONLY

865050 1 Single Coin Optical Switch Harness

--- 122800 1 Microprocessor (female) Pin Extraction Tool...Not Illustrated

IMPORTANT: Check label on computer chip to verify correct part number for microprocessor controller.

6 American Dryer Corporation 450 085- 8

Phase 4.1 Dual Coin Microprocessor Control Box Assembly

For Direct Spark Ignition (DSI) Models ONL Y

Illus. No. Part No. Qty. Description

1 137021 1 2 Microprocessor Socket ONLY
2 137020 1 15-Pin Microprocessor Connector ONLY

122800 1 Microprocessor (female) Pin Extraction Tool...Not Illustrated
3 150315 1 #6 x 3/8” Phillips Pan Head Screw
4 137022 1 15-Pin Strain Relief ONLY
5 137013 4 Nylon Standoff
6 137151 1 Motor Control Solid State Relay Board, 1 HP, 125 VAC - 250 VAC 1Ø

50/60 Hz

7 136057 * 1/2-amp (Slo-Blo) Fuse ONLY

136052 * 4-amp Fuse ONLY
8 150300 2 #10 x 1/2” Hex Washer TEK Screw
9 141403 1 Direct Spark Ignition (DSI) 24VAC Transformer (for gas models Only)
10 150002 2 #6-32 x 1” Round Head Machine Screw
11 120715 1 30-Position T erminal Block
12 151000 2 #6-32 Pal Nut
13 136057 * 1/2-amp (Slo-Blo) Fuse ONLY
14 150301 * #8-18 x 7/16” Phillips Pan Head TEK Screw
15 136008 1 Fuse Block/Strip ONLY

* As required.

450085-8 Telephone: [phone] / www.amdry.com 7

Phase 4 Single Coin Micr opr ocessor Contr ol Panel/Box Assemblies

For Glo-Bar® Ignition Models ONL Y

8 American Dryer Corporation 450 085- 8

Phase 4 Single Coin Microprocessor Control Panel/Box Assemblies

For Glo-Bar® Ignition Models ONL Y

Illus. No. Part No. Qty. Description

1 112526 1 Coin Keyboard Label Assembly
2 800088 1 Phase 4 Coin Microprocessor Control Panel Assembly

(includes illus. nos. 1, 2, 4, 13, and 14)

800168 1 Phase 4 Coin Microprocessor Control Panel Assembly with Battery Option

(includes illus. nos. 1, 2, 4, 13, and 14)
800040 1 Microprocessor Coin Control Panel ONLY
800039 1 Microprocessor Coin Control Panel ONLY with Battery Bracket

3 150415 1 #10-16 x 1/2” Phillips Round Head Crimptite Screw
4 137110 1 Phase 4 Coin Microprocessor Controller ONLY

137115 1 Phase 4 Coin Microprocessor Controller ONLY with Battery Clip

5 -------- 1 Microprocessor Single Coin Acceptor with Optical Switch

(refer to Microprocessor Coin Acceptor Listing on page 61)

6 137056 1 Optical Switch ONLY
7 137023 1 Optical Switch Connector ONLY
8 137021 3 Microprocessor Socket ONLY

865050 1 Single Coin Optical Switch Harness

9 150315 1 #6 x 3/8” Phillips Pan Head Screw
10 137020 1 15-Pin Microprocessor Connector ONLY
11 137021 1 4 Microprocessor Socket ONLY

122800 1 Microprocessor (female) Pin Extraction Tool...Not Illustrated

12 137022 1 15-Pin Strain Relief ONLY
13 153012 4 #8 S tar Washer
14 152001 4 #8-32 Hex Nut
15 137013 4 Nylon Standoff
16 137077 1 Arc Suppressor (A.S.) Board with Relays (115 VAC)

137061 1 Arc Suppressor (A.S.) Board ONLY without Relays
137150 1 Solid State Relay Board ONLY (for 115 volt application Only)

17 137151 2 Motor Control Solid State Relay Board, 1 HP, 125 VAC-250 VAC 1Ø

50/60 Hz

18 136052 2 4-amp Fuse ONLY
19 150002 2 #6-32 x 1” Round Head Machine Screw
20 120709 1 Terminal S trip (8-position)
21 151000 2 #6-32 Pal Nut

IMPORTANT: Check label on computer chip to verify correct part number for microprocessor controller.

450085-8 Telephone: [phone] / www.amdry.com 9

Phase 4 Dual Coin Microprocessor Control Panel/Box Assemblies

For Glo-Bar® Ignition Models ONL Y

10 American Dryer Corporation 450 085- 8

Phase 4 Dual Coin Microprocessor Control Panel/Box Assemblies

For Glo-Bar® Ignition Models ONL Y

Illus. No. Part No. Qty. Description

1 112526 1 Coin Keyboard Label Assembly
2 800088 1 Phase 4 Coin Microprocessor Control Panel Assembly

(includes illus. nos. 1, 2, 4, 13, and 14)
800168 1 Phase 4 Coin Microprocessor Control Panel Assembly with Battery Option

(includes illus. nos. 1, 2, 4, 13, and 14)
800040 1 Microprocessor Coin Control Panel ONLY
800039 1 Microprocessor Coin Control Panel ONLY with Battery Bracket

3 150415 1 #10-16 x 1/2” Phillips Round Head Crimptite Screw
4 137110 1 Phase 4 Coin Microprocessor Controller ONLY

137115 1 Phase 4 Coin Microprocessor Controller ONLY with Battery Clip

5 -------- 1 Microprocessor Single Coin Acceptor with Optical Switch

(refer to Microprocessor Coin Acceptor Listing on page 61)

6 137056 1 Optical Switch ONLY
7 137023 1 Optical Switch Connector ONLY
8 137021 3 Microprocessor Socket ONLY

865051 1 Dual Coin Optical Switch Harness

9 150315 1 #6 x 3/8” Phillips Pan Head Screw
10 137020 1 15-Pin Microprocessor Connector ONLY
11 137021 1 4 Microprocessor Socket ONLY

122800 1 Microprocessor (female) Pin Extraction Tool...Not Illustrated

12 137022 1 15-Pin Strain Relief ONLY
13 153012 4 #8 S tar Washer
14 152001 4 #8-32 Hex Nut
15 137013 4 Nylon Standoff
16 137077 1 Arc Suppressor (A.S.) Board with Relays (115 VAC)

137061 1 Arc Suppressor (A.S.) Board ONLY without Relays
137150 1 Solid State Relay Board ONLY (for 115 volt application Only)

17 137151 2 Motor Control Solid State Relay Board, 1 HP, 125 VAC-250 VAC 1Ø

50/60 Hz

18 136052 2 4-amp Fuse ONLY
19 150002 2 #6-32 x 1” Round Head Machine Screw
20 120709 1 Terminal S trip (8-position)
21 151000 2 #6-32 Pal Nut

IMPORTANT: Check label on computer chip to verify correct part number for microprocessor controller.

450085-8 Telephone: [phone] / www.amdry.com 11

Phase 4 OPL Micr opr ocessor Contr ol Panel Assembly

For Direct Spark Ignition (DSI) Models ONL Y

Illus. No. Part No. Qty. Description

1 112535 1 OPL English Keyboard Label Assembly

112276 1 OPL Stick-On Labels (English Only)...Not Illustrated
112275 1 OPL Stick-On Labels (Spanish, Italian, and Hebrew)...Not Illustrated
112277 1 3-Language OPL Stick-On Labels

(English, Spanish, and Hebrew)...Not Illustrated

112278 1 5-Language OPL Stick-On Labels

(Italian, Dutch, French, German, and Chinese)...Not Illustrated

2 800057 1 Microprocessor Control Panel ONLY

800164 1 Microprocessor Control Panel ONLY with Battery Bracket
800171 1 Phase 4 OPL Non-Reversing Microprocessor Control Panel Assembly

Complete
(includes illus. nos. 1 through 8)

865095 1 Phase 4 OPL Non-Reversing Microprocessor Control Panel Assembly

Complete with Battery Option
(includes illus. nos. 1 through 8)

3 137125 1 Phase 4 OPL Non-Reversing Microprocessor Controller ONLY

137126 1 Phase 4 OPL Non-Reversing Microprocessor Controller ONLY

with Battery Clip
4* 306052 1 Electrostatic Shield ONL Y
5 150108* 4 #8-32 x 1/2” Pan Head Machine Screw

152001 4 #8-32 Hex Nut
6* 153000 4 #8 Steel Burr
7* 137011 4 8-32” Aluminum Standoff
8 160005 1 Spring Turn Latch (2-piece)

IMPORTANT: Check label on computer chip to verify correct part number for microprocessor controller.

* Used on gas dryer models with the Direct Spark Ignition (DSI) system mfd. prior to March 13, 1989.

12 American Dryer Corporation 450 085- 8

Phase 4 OPL Micr opr ocessor Contr ol Box Assembly

For Direct Spark Ignition (DSI) Models ONL Y

Illus. No. Part No. Qty. Description

1 137021 12 * Microprocessor Socket ONLY
2 137020 1 15-Pin Microprocessor Connector ONLY

122800 1 Microprocessor (female) Pin Extraction Tool...Not Illustrated
3 150315 1 #6 x 3/8” Phillips Pan Head Screw
4 137022 1 15-Pin Strain Relief ONLY
5 137013 4 Nylon Standoff
6 137076 1 Arc Suppressor (A.S.) Board with Relay (115 volt controls Only)

137078 1 Arc Suppressor (A.S.) Board with Relay (208/230 volt controls Only)

137061 1 Arc Suppressor (A.S.) Board ONLY without Relay

137151 1 Motor Control Solid State Relay Board, 1 HP, 125 VAC - 250 VAC 1Ø

50/60 Hz
7 136052 1** 4-amp Fuse ONLY
8 131916 1 Electromechanical Relay ONLY (115 VAC)

131930 1 Electromechanical Relay ONLY (208/230 VAC)
9 150300 2 #10-16 x 1/2” Hex Washer TEK Screw
10 141403 1 Direct Spark Ignition (DSI) 24 VAC Transformer (for gas models Only)
11 150002 2 #6-32 x 1” Round Head Machine Screw
12 120715 1 30-Position T erminal Block

120709 1 Terminal S trip (8-position)
13 151000 2 #6-32 Pal Nut

* Some models require a quantity of 14.
** Some models require a quantity of 2.

450085-8 Telephone: [phone] / www.amdry.com 13

Phase 3 OPL Micr opr ocessor Contr ol Panel Assembly

For Glo-Bar® Ignition Models ONL Y

Illus. No. Part No. Qty. Description

1 112535 1 OPL English Keyboard Label Assembly

112276 1 OPL Stick-On Labels (English Only)...Not Illustrated
112275 1 OPL Stick-On Labels (Spanish, Italian, and Hebrew)...Not Illustrated
112277 1 3-Language OPL Stick-On Labels

(English, Spanish, and Hebrew)...Not Illustrated

112278 1 5-Language OPL Stick-On Labels

(Italian, Dutch, French, German, and Chinese)...Not Illustrated

2 800057 1 Microprocessor Control Panel ONLY

800164 1 Microprocessor Control Panel ONLY with Battery Bracket
800161 1 Phase 3 OPL Non-Reversing Microprocessor Control Panel Assembly

Complete
(includes illus. nos. 1 through 5)

800163 1 Phase 3 OPL Non-Reversing Microprocessor Control Panel Assembly

Complete with Battery Option
(includes illus. nos. 1 through 5)

3 137092 1 Phase 3 OPL Non-Reversing Microprocessor Controller ONLY

137093 1 Phase 3 OPL Non-Reversing Microprocessor Controller ONLY

with Battery Clip
4 152001 4 #8-32 Hex Nut
5 160005 1 Spring Turn Latch (2-piece)

IMPORTANT: Check label on computer chip to verify correct part number for microprocessor controller.

NOTE: OPL microprocessor controllers listed are suitable for ALL voltage applications.

14 American Dryer Corporation 450 085- 8

Phase 3 OPL Micr opr ocessor Contr ol Box Assembly

For Glo-Bar® Ignition Models ONL Y

Illus. No. Part No. Qty. Description

1 137020 1 15-Pin Microprocessor Connector ONLY
2 137021 13 Microprocessor Socket ONLY

122800 1 Microprocessor (female) Pin Extraction Tool...Not Illustrated
3 150315 1 #6 x 3/8” Phillips Pan Head Screw
4 137022 1 15-Pin Strain Relief ONLY
5 137013 4 Nylon Standoff
6 137077 1 Arc Suppressor (A.S.) Board with Relays (115 volt controls Only)

137061 1 Arc Suppressor (A.S.) Board ONLY without Relays

137150 1 Solid State Relay (115 volt application Only)

137151 1 Motor Control Solid State Relay Board, 1 HP, 125 VAC - 250 VAC 1Ø

50/60 Hz
7 131916 2 Electromechanical Relay ONLY (115 VAC)
8 136052 2 4-amp Fuse ONLY
9 150002 2 #6-32 x 1” Round Head Machine Screw
10 120709 1 Terminal S trip (8-position)
11 151000 2 #6-32 Pal Nut

450085-8 Telephone: [phone] / www.amdry.com 15

Dual T imer Contr ol Panel/Box Assemblies

For Direct Spark Ignition (DSI) Models ONL Y

Illus. No. Part No. Qty. Description

1 123000 1 Red Indicator Light (115 volt)

123001 1 Red Indicator Light (230 volt)
2 122400 1 Rocker Heat Selector Switch
3 865550 1 Dual Timer Control Panel Assembly Complete 115 VAC

(includes illus. nos. 1 through 21)

865551 1 Dual T imer Control Panel Assembly Complete 230 VAC

(includes illus. nos. 1 through 21)

800051 1 Dual Timer Control Panel ONLY
4 131812 1 Push-T o-Start Relay (1 15 volt)

131813 1 Push-T o-S tart Relay (230 volt)
5 150207 2 #10-24 x 1/2” Round Head Machine Screw

16 American Dryer Corporation 450 085- 8

Dual T imer Control Panel/Box Assemblies (continued)

For Direct Spark Ignition (DSI) Models ONLY

Illus. No. Part No. Qty. Description

6 154001 2 #10-24 Speed Nut
7 152013 2 #6-32 Hex Nut
8 153010 2 #6 S tar Washer
9 120708 1 3-Position T erminal Block

120713 1 18-Position T erminal Block
10 150002 2 #6-32 x 1” Round Head Machine Screw
1 1 150110 4 #8-32 x 1/4” Phillips Head Machine Screw
12 150001 2 #6-32 x 1/2” Round Head Machine Screw
13 131030 1 Dual Timer Relay (1 15 volt)

131031 1 Dual Timer Relay (230 volt)
14 151000 2 #6-32 Pal Nut
15 112050 1 Dual Timer Label ONLY
16 160005 1 Spring Turn Latch (2-piece)
17 124103 2 Arrow Timer Knob ONLY
18 124020 1 60 Minute Timer (115 volt)

124021 1 60 Minute Timer (230 volt)
19 124022 1 15 Minute Timer (115 volt)

124023 1 15 Minute Timer (230 volt)
20 122602 1 9-Pin Connector ONLY
21 122700 9 Pin T erminal ONLY
22 122603 1 9-Pin Socket Connector ONLY
23 122701 9 Socket T erminal ONLY

122801 1 Pin/Socket Extraction T ool...Not Illustrated
24 136002* 1 Panel Mount Fuse Holder Assembly ONLY

875250* 1 In-Line Fuse Holder Assembly ONLY
25** 136052 1 4-amp Fuse ONLY

136054 1 15-amp (Slo-Blo) Fuse ONLY

136056 1 20-amp (Slo-Blo) Fuse ONLY
26 141403 1 Direct Spark Ignition (DSI) 24 VAC Transformer
27 150300 2 #10-16 x 1/2” Hex Washer TEK Screw
28 150415 2 #10-16 x 1/2” Phillips Round Head Crimptite Screw
29 131814 1 Motor Control Relay ONL Y (1 15 volt)

131815 1 Motor Control Relay ONL Y (230 volt)
30 150002 2 #6-32 x 1” Round Head Machine Screw
31 120715 1 30-Position T erminal Block

120709 1 Terminal S trip (8-position)
32 151000 2 #6-32 Pal Nut

* Model application varies.
** Check fuse rating for verification.

450085-8 Telephone: [phone] / www.amdry.com 17

Dual T imer Contr ol Panel/Box Assemblies

For Glo-Bar® Ignition Models ONL Y

18 American Dryer Corporation 450 085- 8

Dual T imer Contr ol Panel/Box Assemblies

For Glo-Bar® Ignition Models ONL Y

Illus. No. Part No. Qty. Description

1 123000 1 Red Indicator Light (115 volt)

123001 1 Red Indicator Light (230 volt)
2 122400 1 Rocker Heat Selector Switch
3 865550 1 Dual Timer Control Panel Assembly Complete 115 VAC

(includes illus. nos. 1 through 21)

865551 1 Dual T imer Control Panel Assembly Complete 230 VAC

(includes illus. nos. 1 through 21)

800051 1 Dual Timer Control Panel ONLY
4 131812 1 Push-T o-Start Relay (1 15 volt)

131813 1 Push-T o-S tart Relay (230 volt)
5 150207 2 #10-24 x 1/2” Round Head Machine Screw
6 154001 2 #10-24 Speed Nut
7 152013 2 #6-32 Hex Nut
8 153010 2 #6 S tar Washer
9 120708 1 3-Position T erminal Block

120713 1 18-Position T erminal Block
10 150002 2 #6-32 x 1” Round Head Machine Screw
1 1 150110 4 #8-32 x 1/4” Phillips Head Machine Screw
12 150001 2 #6-32 x 1/2” Round Head Machine Screw
13 131030 1 Dual Timer Relay (1 15 volt)

131031 1 Dual Timer Relay (230 volt)
14 151000 2 #6-32 Pal Nut
15 112050 1 Dual Timer Label ONLY
16 160005 1 Spring Turn Latch (2-piece)
17 124103 2 Arrow Timer Knob ONLY
18 124020 1 60 Minute Timer (115 volt)

124021 1 60 Minute Timer (230 volt)
19 124022 1 15 Minute Timer (115 volt)

124023 1 15 Minute Timer (230 volt)
20 122602 1 9-Pin Connector ONLY
21 122700 9 Pin T erminal ONLY
22 122603 1 9-Pin Socket Connector ONLY
23 122701 9 Socket T erminal ONLY

122801 1 Pin/Socket Extraction T ool...Not Illustrated
24 150415 2 #10-16 x 1/2” Phillips Round Head Crimptite Screw
25 131814 1 Motor Control Relay ONL Y (1 15 volt)

131815 1 Motor Control Relay ONL Y (230 volt)
26 150002 2 #6-32 x 1” Round Head Machine Screw
27 120709 1 Terminal S trip (8-position)
28 151000 2 #6-32 Pal Nut

450085-8 Telephone: [phone] / www.amdry.com 19

Non-Micropr ocessor Coin Contr ol Panel/Box Assemblies

For Direct Spark Ignition (DSI) and Glo-Bar® Ignition Models

MAN0264

20 American Dryer Corporation 450 085- 8

Non-Micropr ocessor Coin Contr ol Panel/Box Assemblies

For Direct Spark Ignition (DSI) and Glo-Bar® Ignition Models

Illus. No. Part No. Qty. Description

1 123000 1 Red Indicator Light (115 volt)

123001 1 Red Indicator Light (230 volt)
2 122400 1 Rocker Heat Selector Switch
3 800070 1 Coin Meter Control Panel Assembly Complete 115 VAC

(includes illus. nos. 1 through 6 and 8 through 12)

800071 1 Coin Meter Control Panel Assembly Complete 230 VAC

(includes illus. nos. 1 through 6 and 8 through 12)

800052 1 Coin Meter Control Panel ONLY
4 131812 1 Push-T o-Start Relay (1 15 volt)

131813 1 Push-T o-S tart Relay (230 volt)
5 150207 2 #10-24 x 1/2” Round Head Machine Screw
6 154001 2 #10-24 Speed Nut
7* 125000 1 25¢ 115 Volt Meter (specify timing)

125003 1 25¢ 230 Volt Meter (specify timing)
8 150303 2 #4 x 3/4” Pan Head “A” Screw
9 120713 1 18-Position T erminal Block

(for models mfd. as of May 15, 1989)

120707 1 Terminal S trip (2-position)

(for models mfd. prior to May 15, 1989)
10 160005 1 Spring Turn Latch (2-piece)
11 122602 1 9-Pin Connector ONLY
12 122700 9 Pin T erminal ONLY
13 122603 1 9-Pin Socket Connector ONLY
14 122701 9 Socket T erminal ONLY

122801 1 Pin/Socket Extraction T ool...Not Illustrated
15 150300 2 #10-16 x 1/2” Hex Washer TEK Screw
16 141403 1 Direct Spark Ignition (DSI) 24 VAC Transformer

(for Direct Spark Ignition [DSI] models Only)
17 150415 2 #10-16 x 1/2” Phillips Round Head Crimptite Screw
18 131814 1 Motor Control Relay ONL Y (1 15 volt)

131815 1 Motor Control Relay ONL Y (230 volt)
19 150002 2 #6-32 x 1” Round Head Machine Screw
20 120715 1 30-Position T erminal Block (for Direct Spark Ignition [DSI] models Only)

120709 1 Terminal S trip (8-position)
21 151000 2 #6-32 Pal Nut

* Consult factory for coin meters not listed.

450085-8 Telephone: [phone] / www.amdry.com 21

Coin Meter Replacement Parts

Illus. No. Part No. Qty. Description

1 125511 1 1/60 RPM 115 Volt 60 Hz Meter Motor

125532 1 1/60 RPM 230 Volt 60 Hz Meter Motor
125512 1 1/60 RPM 240 Volt 50 Hz Meter Motor
125513 1 1/30 RPM 240 Volt 50 Hz Meter Motor

2 125500 1 2-Point Cam

125501 1 3-Point Cam
125502 1 4-Point Cam
125503 1 5-Point Cam
125504 1 6-Point Cam
125506 1 8-Point Cam
125507 1 9-Point Cam
125508 1 10-Point Cam

125510 1 12-Point Cam
3 125515 1 Master Switch “B” with Arm
4 125516 2 Master Switch “A” or “C”

22 American Dryer Corporation 450 085- 8

Coin Vault Assembly

Illus. No. Part No. Qty. Description

1 802131 1 Microprocessor Coin Vault Assembly Complete

(includes illus. nos. 1 through 6)

802130 1 Non-Microprocessor Coin Vault Assembly Complete

(includes illus. nos. 1 through 6)
802121 1 Microprocessor Coin Vault ONLY
802120 1 Non-Microprocessor Coin Vault ONLY

2 160006 1 Cam for 1/4 Turn Lock ONLY
3 160007 1 1/4 T urn Lock with Key

160105* 1 1/4 Turn Mer-Pel Key ONLY

4 802020 1 1/4 T urn Coin Box Assembly

(includes illus. nos. 2 through 5)
802019 1 1/4 Turn Coin Box ONLY without Faceplate

5 802018 1 1/4 T urn Coin Box Faceplate ONLY
6 152014 4 1/4-20 Free Spin Wash Nut
7 309250 1 Coin V ault Slot Cover
8 102503 1 Control Door Support Rod
9 102601 1 Control Door Rod Retainer Clip
10 102600 1 Control Door Support Rod Catch

* Specify key number when ordering.

450085-8 Telephone: [phone] / www.amdry.com 23

Fr ont Panel Assembly

Latch-T ype

Illus. No. Part No. Qty. Description

1* 800676 1 Front Panel Assembly (latch-type) Complete with Hinge

(includes illus. nos. 1 through 3 and 6)

800677 1 Stainless Steel Front Panel Assembly (latch-type) Complete with Hinge

(includes illus. nos. 1 through 3 and 6)
2 154215 2 5/32” Pop Rivet
3 170330 1 Friction Door Latch
4 150300 1 #10-16 x 1/2” Hex Washer TEK Screw
5 150415 8 #10-16 x 1/2” Phillips Round Head Crimptite Screw
6 121405 1 Rubber Grommet
7 150205 2 #10-32 x 1/4” Fillister Head Screw
8 --------- 1 N.S. Series Door Switch

(for microprocessor models mfd. as of November 21, 1990

and non-microprocessor models mfd. as of November 15, 1990)

(refer to Main Door Switch Assembly on

* Specify color when ordering.

24 American Dryer Corporation 450 085- 8

page 28)