RADD™ Introduction
American DJ®
RADD
Introduction:
Thank you for purchasing the American DJ Radd.™ To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations of this unit. The
American DJ® Radd™ is a unique moon ower effect. This unit has
several multi-colored gobo combinations. This unit has been designed
to compliment the American DJ® DJ Scan™ and DJ Roller.™ This unit
has been tested at the factory before being shipped to you. There is no
assembly required.
Customer Support:
American DJ® provides a toll free customer support line, to provide set
up help and to answer any question should you encounter problems
during your set up or initial operation. You may also visit us on the web
at www.americandj.com for any comments or suggestions.
Service Hours are Monday through Friday 10:00 a.m. to 5:00 p.m.
Pacic Time.
Voice: (800) 322-6337
Fax: (323) 582-2610
E-mail: support@americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
User Instructions
American DJ
4295 Charter Street
Los Angeles Ca. 90058
www.americandj.com
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
your nearest American DJ dealer.
Do not discard this cartoon in the trash. Please recycle when ever possible.
HALOGEN LAMP WARNING!
This fixture is fitted with a halogen lamp which is highly susceptible
to damage if improperly handled. Never touch lamp with your bare
fingers as the oil from your hands will shorten lamp life. Also, never
move the fixture until the lamp has had ample time to cool. Remember,
lamps are not covered under warranty conditions.
©American DJ Supply® - www.americandj.com - Radd™ Instruction Manual Page 2
RADD™ Warnings
RADD™ Features
• Do not spill water or other liquids in to or on to your unit.
• Be sure that the local power outlet matches the required voltage
for your fixture.
• Do not attempt to operate this unit if the power cord has been frayed
or broken. Please route your power cord out of the way of foot
traffic.
• Do not attempt to remove or break off the ground prong from the
electrical cord. This prong is used to reduce the risk of electrical
shock and fire in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the top cover under any conditions. There are no user
serviceable parts inside.
• Disconnect the unit’s main power when left unused for long periods
of time.
• Never connect this unit to a dimmer pack
• Always be sure to mount this unit in area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Never block the ventilation holes.
• Do not attempt to operate this unit, if it becomes damaged in
any way.
• Never operate this unit when it’s cover is removed.
Congratulations and thank you for purchasing the American DJ “RADD,”
one of the finest pieces of its kind on the market today! The RADD
is a great inexpensive, light weight, mini intelligent fixture. Due to it’s
physical specifications, it’s a great piece for mobile DJ’s, roller rinks,
small clubs, bars, and bowling centers. When used in multiples of two
(2) or more, these units create an effect that rivals that of units that can
cost up to three times the price. The RADD™ was designed to run in
master/slave mode but can be used with a standard dmx controller. The
RADD features a bright 150 watt/500 Hr lamp life halogen bulb
with a separate gobo and color wheel. The color wheel features seven
brilliant colors plus white and the gobo wheel features 9 gobos plus a
large and small spot. This units is ready to be installed or hung and
powered right out of the box. There is no assembly required. This fixture
incorporates the use of high quality stepper motors for a more accurate
mirror movement. Mirror movement allows for a full 90 degree tilt
(vertical) and a full 90 degree pan (horizontal). An internal built in
microphone allows the fixtures to run in Stand Alone mode so there is
no need for an external controller. The RADD™ may also be set-up to
run in a Master-Slave mode when used in multiples, up to 16 units. When
used in the Master-Slave mode, the unit will chase to several internal
programs. The RADD™ can also be controlled via a standard DMX
controller such as the American DJ Show Designer,™ or the American
DJ® DMX Operator,™ giving the user independent control over the gobo
and color wheel as well as the mirrors pan and tilt movements.
RADD™ General Instructions
Please read and understand the instructions in this manual carefully and
thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance.
Please keep this manual with the unit for future reference.
©American DJ Supply® www.americandj.com Radd™ Instruction Manual Page 3
Note: The built in programs in the RADD are so good you may never
need a DMX controller.
©American DJ Supply® - www.americandj.com - Radd™ Instruction Manual Page 4
RADD™ Set Up
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 IN
(X-CALIBUR)
CONNECTOR
3 PIN
DMX512 OUT
CONTROLLER
CONNECTOR
3 PIN
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
RADD™ Set Up Cont.
Unpacking:
Every Radd has been thoroughly tested and has been shipped in perfect operating order. Carefully check the shipping carton for damage that may have occurred
during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage. In the case damage has been found please contact our toll
free customer support number for further instructions.
Power Supply:
Before plugging your unit in be sure the source voltage in your area matches
the required voltage for your American DJ® Radd.™ The American DJ® Radd is
available in a 115v and 230v version. Because line voltage may vary from venue to
venue, you should be sure to plug your power supply into a matching wall outlet
before attempting to operate you controller.
Data Cable (DMX Cable) Requirements:
Your fixture and your controller require a standard 3-pin
XLR connector for data input and data output (Figure
1). If you are making your own cables be sure to
use standard two conductor shielded cable (This cable
may be purchased at almost all pro sound and lighting
stores). Your cables should be made with a male and
female XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained and
can not be “Y”ed or split.
Notice: Do not use the ground lug on the XLR connector. Do not connect the
cable’s shield conductor to the ground lug or allow the shield conductor to come
in contact with the XLR’s outer casing. Grounding the shield could cause a short
circuit and erratic behavior.
Notice: Be sure to follow figures two and three when making your own cables.
Do not use the ground lug on the XLR connector. Do not connect the cable’s
shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit
and erratic behavior.
Configuration:
Pin
XLR
TH
EAR
1
3
2 COL
HO
D
T
SOCKET
MALE
COL
D 2
XLR
EAR
1
HO
3
SOCKET
FEMALE
XLR
TH
Pin
Pin
T
Pin
1
2
3
=
=
=
Shiel
Data
Data
d
Compliment
(positiv
ue
Tr
(negativ
e)
Figure 2
Special Note: Line Termination.
When longer runs of cable are used, you may need to use a terminator on the
last unit to avoid erratic behavior. A terminator is a 90-120 ohm 1/4 watt resistor
which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last unit in
your daisy chain to terminate the line. Using a cable terminator will decrease the
possibilities of erratic behavior.
Figure 4
Figure 1
Linking:
The Radd is a DMX intelligent scanner and must follow standard DMX protocol.
A DMX signal cannot be split or “Y-ed” unless you are using an approved DMX
splitter such as the American DJ® DMX Branch 4.™ Link your scanners together
using standard DMX cable as described on page 5 of this manual. Be sure that
each fixture follows an “IN”/”OUT” pattern starting from you DMX controller.
Your controller will always be the first output in a DMX chain. Link all your DMX
devices together regardless of their brand or type.
Figure 5 on page 7 details the proper linking procedure.
e)
Figure 3
©American DJ Supply® - www.americandj.com - Radd™ Instruction Manual Page 5
©American DJ Supply® - www.americandj.com - Radd™ Instruction Manual Page 6