P36 BlinderRGB Introduction
American DJ®
Unpacking: Thank you for purchasing the P36 BlinderRGB by Ameri-
can DJ®. Every P36 BlinderRGB has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fixture for any
damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Do not return this unit to your dealer without first contacting customer support.
Introduction: The P36 BlinderRGB is part of American DJ’s continu-
ing pursuit for creating high quality affordable intelligent fixtures. The
P36 BlinderRGB is a DMX intelligent LED color wash. This wash can be
used in a stand alone mode or connected in a Master/Slave configuration. The unit can also be controlled via DMX controller. This wash has
four operating modes: Sound Active mode, Auto mode, RGB mode,
and DMX control mode.
Customer Support: American DJ® provides a toll free customer sup-
port line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 9:00 a.m. to
5:00 p.m. Pacific Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2610
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
5/06
User Instructions
American DJ®
4295 Charter Street
Los Angeles Ca. 90058
www.americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
American DJ®.
PLEASE recycle the shipping carton when ever possible.
©American DJ Supply® - www.americandj.com - P36 BlinderRGB Instruction Manual Page 2
P36 BlinderRGB General Instructions
P36 BlinderRGB Safety Precautions
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
P36 BlinderRGB Features
• Mulit-Colors
• Color Strobe
• Electronic Dimming 0-100%
• Built in Microphone
• DMX-512 protocol
• Uses Seven DMX Channels
P36 BlinderRGB Warranty Registration
The P36 BlinderRGB carries a 1 year (365 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www.
americandj.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact American DJ®
cus-
tomer support for a R.A. number.
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and fire in case of an internal short.
• Disconnect
from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 12 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
©American DJ Supply® - www.americandj.com - P36 BlinderRGB Instruction Manual Page 4©American DJ Supply® - www.americandj.com - P36 BlinderRGB Instruction Manual Page 3
P36 BlinderRGB Set Up
DMX512 IN
3-PIN XLR
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Terminatio n re duces signal errors and
avo ids signal tran smis sion problem s
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
1
2
3
Terminatio n re duces signal errors and
avo ids signal tran smis sion problem s
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
P36 BlinderRGB Set Up
Power Supply: Before plugging your unit in, be sure the source voltage in your area matches the required voltage for your American DJ®
P36 BlinderRGB. The American DJ® P36 BlinderRGB is available in a
120v and 220v version. Because line voltage may vary from venue to
venue, you should be sure your unit voltages matches the wall outlet
voltage before attempting to operate you fixture.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that trav
els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter
minals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fixtures and the controller are DMX compli
ant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The P36 BlinderRGB can be controlled via DMX-512 protocol. The P36
BlinderRGB is a seven channel DMX unit. The DMX address is set on
the back panel of the P36 BlinderRGB. Your unit and your DMX controller require a standard 3-pin XLR connector for
data input and data output (Figure 1). If you are
making your own cables, be sure to use standard
two conductor shielded cable (This cable may be
purchased at almost all pro sound and lighting
stores). Your cables should be made with a male
and female XLR connector on either end of the
cable. Also remember that DMX cable must be
daisy chained and can not be split.
Figure 1
©American DJ® - www.americandj.com - P36 BlinderRGB Instruction Manual Page 5
-
-
-
Notice: Be sure to follow figures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
Figure 2
XLR Male Socket
1 Ground
2 Cold
3 Hot
Figure 3
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
5-Pin XLR DMX Connectors.
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The
chart below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
©American DJ Supply® - www.americandj.com - P36 BlinderRGB Instruction Manual Page 6
XLR Female Socket
2 Cold
1 Ground
3 Hot
When longer runs of cable are
Some manufactures use 5-pin XLR
3-Pin XLR to 5-Pin XLR Conversion
Pin 1
Pin 2
Pin 3
XLR Pin Configuration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
Figure 4
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
P36 BlinderRGB Operating Instructions
P36 BlinderRGB Operating Instructions
Operating Modes:
You can use the P64 BlinderRGB in either a stand alone mode or a
master/slave configuration, there are 4 modes to choose from:
• Sound-Active mode the built in programs
• Auto Mode - The unit will automatically chase through the different
colors, with or without a strobe effect.
• RGB Mode - Choose a single color or colors to stay static or
strobe.
• DMX control mode - This function will allow you to control
individual fixtures traits with a standard DMX 512 controller such as
as the
Elation® Show Designer™.
The unit will react to sound, chasing through
, with or without a strobe effect.
each
Master-Slave Operation:
This function will allow
Slave mode. In Master-Slave operation one unit will act as the con
trolling
programs. Any unit can act as a Master or as a Slave however, only
one unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of
input and the Female XLR connector is the output. The first
unit in the chain (master) will use the female XLR connector
connector only.
2. Set dipswitches #1 and #10 to the “ON” position, on the “Master”
unit.
3. For the “Slave” unit(s), dipswitch #10 must remain in the “Off”
position, other then that you may set the dipswitch(es) at any
setting
4. Connect the “Slave” unit or units and they will automatically start
to follow the “Master.”
unit and the others will react to the controlling units built-in
the unit. Use standard XLR microphone cables to link your
units together. Remember that the Male XLR connector is the
only. The last unit in the chain will use the male XLR
.
s you to link units together to run in a Master-
Sound Active Mode:
In this mode the P36 BlinderRGB will react to sound, and chase
through the different colors.
1. Plug the fixture in and put dipswitch #10 in the “ON” postion and
follow the dipswitch settings on page 9 for the different sound
active programs. If you want the unit to strobe, put dipswitch #7
into the “ON” position also.
2. The fixture will now change via sound.
Auto Mode:
1. Plug the fixture in and put dipswitches # 9 and 10 in the “ON”
postion. If you want the unit to strobe, put dipswitch #7 into
the “ON” position also.
2. Adjust the speed knob to contol the rate of change.
RGB (Red, Green, and/or Blue) Mode:
1. Plug the fixture in and put dipswitches #8, 9, and 10 in the “ON”
postion. Then follow the instructions below to activate the color or
-
colors of your choice. If you want the unit to strobe, put dip-
switch #7 into the “ON” position also.
2. RED - Dipswitch #1 in the “ON” position will give you an intensity
of 25%. Dipswitch #2 in the “ON” position will give you an intensity
of 50%. Dipswithes #1 and #2 in the “ON” position will give you an
intensity of 100%.
GREEN - Dipswitch #3 in the “ON” position will give you an inten sity of 25%. Dipswitch #4 in the “ON” position will give you an
intensity of 50%. Dipswithes #3 and #4 in the “ON” position will
give you an intensity of 100%.
BLUE
of 25%. Dipswitch #6 in the “ON” position will give you an inten sity
of 50%. Dipswithes #5 and #6 in the “ON” position will give you an
intensity of 100%.
- Dipswitch #5 in the “ON” position will give you an intensity
DMX Mode:
Operating through a DMX controller give the user the freedom to create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller such as the
Elation® Show Designer™ or the Elation® DMX Operator.™
2. The P36 BlinderRGB
©American DJ Supply® - www.americandj.com - P36 BlinderRGB Instruction Manual Page 8©American DJ Supply® - www.americandj.com - P36 BlinderRGB Instruction Manual Page 7
uses seven DMX channels to operate see
(1) Sound action with 31 colors without strobe: The
sound will make the unit change its light color between
31 predefined mixed colors without strobe.
Sensitivity
(2) Sound action with 31 colors with strobe: The
sound will make the unit change its light color between
31 predefined mixed colors with strobe.
Sensitivity
Sensitivity
(3) Sound action with 7 colors without strobe: The
sound will make the unit change its light color between 7
colors: red, orange, yellow, green, blueness, blue, purple.
Sensitivity
(4) Sound action with 7 colors with strobe: The sound
will make the unit change its light color between 7 colors:
red, orange, yellow, green, blueness, blue, purple.
Sensitivity
(5) Sound action with 3 colors without strobe: The
sound will make the unit change its light color between 3
colors: red, green, blue.
Sensitivity
(6) Sound action with 3 colors with strobe: The sound
will make the unit change its light color between 3 colors:
red, green, blue.
P36 BlinderRGB Operating Instructions
P36 BlinderRGB DMX Values and Functions
page 10 for the DMX traits.
3. To run your fixture in DMX mode, plug in the fixture via the XLR
connections to any standard DMX controller. Switch dipswitch
#1 to the “ON” position. - Follow the set-up specifications that
come with your DMX controller.
P36 BlinderRGB Sound Active Programs
Channel Value Function
1 0 - 255 RED
0% 100%
2 0 - 255 GREEN
0% 100%
3 0 - 255 BLUE
0% 100%
4 0 - 12 NOTHING
13 - 255 COLOR MACRO
5 0 - 255 STROBING
SLOW FAST
6 0 - 10 NOTHING
11 - 35 DIMMING EFFECT
DIM BRIGHT DIM
36 - 60 STROBING LEFT TO RIGHT
GREEN/RED
61 - 85 STROBING LEFT TO RIGHT
GREEN/BLUE
86 - 110 STROBING LEFT TO RIGHT
BLUE/RED
111 - 135 3 COLOR FLASH
136 - 160 7 COLOR FLASH
161 - 185 3 COLOR FADE
186 - 210 7 COLOR FADE
211 - 235 AUTO MIX
236 - 245 SOUND ACTIVE 3 COLOR CHANGE
246 - 255 SOUND ACTIVE 7 COLOR CHANGE
7 0 - 255 DIMMER CONTROL
0% 100%
Note: Please see the next page for information concerning the
DMX values and functions.
©American DJ Supply® - www.americandj.com - P36 BlinderRGB Instruction Manual Page 10©American DJ Supply® - www.americandj.com - P36 BlinderRGB Instruction Manual Page 9
P36 BlinderRGB DMX Values and Functions
P36 BlinderRGB Trouble Shooting
Channel 1, 2, and 3 will not work, when Channel 4 is being
used.
When the value of Channel 6 is between 1 and 35, you must be
using Channels 1, 2, 3, or all three combined.
When using Channel 6, Channel 5 will control the speed of the
color changing.
P36 BlinderRGB Macro Color List
MACROS
VALUE LEFT/RIGHT COLOR
0 - 12 NO MACRO
13 - 25 RED/RED
26 - 38 YELLOW/YELLOW
39 - 51 GREEN/GREEN
52 - 64 CYAN/CYAN
65 - 77 BLUE/BLUE
78 - 90 MAGENTA/MAGENTA
91 - 103 WHITE/WHITE
104 - 116 RED/GREEN
117 - 129 RED/BLUE
130 - 142 GREEN/RED
143 - 155 GREEN/BLUE
156 - 168 BLUE/RED
169 - 181 BLUE/GREEN
182 - 194 CYAN/MAGENTA
195 - 207 CYAN/YELLOW
208 - 220 MAGENTA/CYAN
221 - 233 MAGENTA/YELLOW
234 - 246 YELLOW/CYAN
247 - 255 YELLOW/MAGENTA
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
If problems are not resolved;
1-800-322-6337
P36 BlinderRGB Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Use a brush to wipe down the fan grill.
3. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
4. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
Contact American DJ® for service.
R = RED; G = GREEN; B = BLUE
Y = YELLOW; C = CYAN;
M = MAGENTA; W = WHITE
©American DJ Supply® - www.americandj.com - P36 BlinderRGB Instruction Manual Page 11
©American DJ Supply® - www.americandj.com - P36 BlinderRGB Instruction Manual Page 12
P36 BlinderRGB Warranty P36 BlinderRGB Notes
1-YEAR LIMITED WARRANTY
A. American DJ® hereby warrants, to the original purchaser, American DJ® products to be
free of manufacturing defects in material and workmanship for a period of 1 Year (365 days)
from the date of purchase. This warranty shall be valid only if the product is purchased
within the United States of America, including possessions and territories. It is the owner’s
responsibility to establish the date and place of purchase by acceptable evidence, at the
time service is sought.
B. For warranty service, send the product only to the American DJ
® factory. All shipping
charges must be pre-paid. If the requested repairs or service (including parts replacement)
are within the terms of this warranty, American DJ
® will pay return shipping charges only
to a designated point within the United States. If the entire instrument is sent, it must be
shipped in its original package. No accessories should be shipped with the product. If any
accessories are shipped with the product, American DJ
® shall have no liability whatsoever
for loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which American DJ® concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than
the American DJ
American DJ
® factory unless prior written authorization was issued to purchaser by
®; if the product is damaged because not properly maintained as set forth in
the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, American DJ
® will replace defec-
tive parts at its expense, and will absorb all expenses for warranty service and repair labor
by reason of defects in material or workmanship. The sole responsibility of American DJ
under this warranty shall be limited to the repair of the product, or replacement thereof,
including parts, at the sole discretion of American DJ
®. All products covered by this war-
ranty were manufactured after January 1, 1990, and bear identifying marks to that effect.
E. American DJ® reserves the right to make changes in design and/or improvements upon
its products without any obligation to include these changes in any products theretofore
manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any acces
sory supplied with products described above. Except to the extent prohibited by applicable
law, all implied warranties made by American DJ® in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period
set forth above. And no warranties, whether expressed or implied, including warranties
of merchantability or fitness, shall apply to this product after said period has expired. The
consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly
provided above; and under no circumstances shall American DJ® be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
G. This warranty is the only written warranty applicable to American DJ® Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions
heretofore published.
®
-
H. Lamps are not covered under this or any other warranty, either written or implied.
©American DJ Supply® - www.americandj.com - P36 BlinderRGB Instruction Manual Page 13 ©American DJ Supply® - www.americandj.com - P36 BlinderRGB Instruction Manual Page 14
P36 BlinderRGB Specifications
Model:
SPECIFICATIONS:
Working Position: Any safe working position
Voltage: 120V or 230V
Power Consumption: 65W
Power Draw: 0.6 Amps
Weight: 20lbs./ 9.0Kgs.
Dimensions: 4” (L) x 19” (W) x 31” (H)
Colors: RGB Color Mixing
DMX Channels: 7
Warranty: 1 Year (365 days)
Please Note: Specifications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
P36 BlinderRGB™
©American DJ Supply® - www.americandj.com - P36 BlinderRGB Instruction Manual Page 15
©American DJ Supply
American DJ World Headquarters:
4295 Charter Street Los Angeles, CA 90058 USA
Tel: 323-582-2650 / Fax: 323-582-2610
Web: www.americandj.com / E-mail: info@americandj.com
Loading...