Amazon Smart Plug and Bulbs Installation Manual

Connect to your Alexa
or Google Assistant
device to control your
devices with your voice.

Try these voice
commands:

Amazon Alexa

Alexa, turn off the
living room.

Alexa, good morning.
Alexa, turn on table

lamp.

Google Assistant

Hey Google, turn on
the lights.

Hey Google, turn off
bathroom plug.

Hey Google, I’m leaving.

On/Off Button

LED Indicator Light

FCC Compliance Statement Compliance Notice:

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

How to Set Up and Enable Voice

and Out of Home Control for

Your Smart Plug and Bulbs

Install

your Smart Plug.

If pairing with

Smart Bulbs,

install those in the

same room as

the Smart Plug.

Now you can control your lights with your voice and away from home.

Download

the

C by GE app.

Then, add Smart Bulbs
to the C by GE app in

Follow the instructions

Voila!

Add

your Smart Plug

to the C by GE app.

the same room.

in the app to set up

your voice assistant.

FCC Compliance Statement Compliance Notice:

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer­ence in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accor­dance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of FCC rules. Operation is subject to
the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interfer­ence that may cause undesired operation.

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of FCC rules. Operation is subject to
the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interfer-
ence that may cause undesired operation.

Changes or modifications that are not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.

RF Exposure Information:

This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. In order to avoid the possibility of exceed­ing the FCC radio frequency exposure limits, human proximity to the
antenna shall not be less than 8 inches during normal operation.

RF Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set
forth for an uncontrolled environment. This transmitter must be installed
to provide a separation distance of at least 8 inches from all persons
and must not be collocated or operating in conjunction with any other
antenna or transmitter.

CAUTION - High Voltage - Disconnect power supply before servicing
Operation temperature: 0-40ºC
For Control of Electronic Ballast, CFL, LED Lamps
Type 1 Enclosure
IP20
Pollution Degree 2
Impulse Voltage: 1500V

Indoor use only.

Models
CPLGSTDBLW1

PK-00102787-1