Amana W10420474A User Manual
TOP-LOADING
GUIDE D’UTILISATION
HIGH EFFICIENCY
LOW-WATER WASHER
USE AND CARE GUIDE
Table of Contents
WASHER SAFETY ............................................................ 2
WHAT’S NEW UNDER THE LID? .................................... 3
CONTROL PANEL AND FEATURES ...............................4
CYCLE GUIDE .................................................................. 6
USING YOUR WASHER ................................................... 7
WASHER MAINTENANCE ............................................. 10
TROUBLESHOOTING .................................................... 12
WARRANTY .................................................................... 17
ASSISTANCE OR SERVICE ....................... BACK COVER
ET D’ENTRETIEN DE
LA LAVEUSE HAUTE
EFFICACITÉ À FAIBLE
CONSOMMATION D’EAU
AVEC CHARGEMENT
PAR LE DESSUS
Table des matières
SÉCURITÉ DE LA LAVEUSE .........................................18
QUOI DE NEUF SOUS LE COUVERCLE? .................... 19
TABLEAU DE COMMANDE
ET CARACTÉRISTIQUES .............................................. 20
GUIDE DE PROGRAMMES ........................................... 21
UTILISATION DE LA LAVEUSE ..................................... 23
ENTRETIEN DE LA LAVEUSE .......................................26
DÉPANNAGE .................................................................. 28
GARANTIE ...................................................................... 34
ASSISTANCE OU SERVICE. .... COUVERTURE ARRIÈRE
W10420474A
W10420475A - SP
Para una versión de estas instrucciones en español, visite www.amana.com
Designed to use only HE High Efciency
detergents.
Conçue pour l’utilisation d’un détergent haute
efcacité seulement.
WASHER SAFETY
2
WHAT’S NEW UNDER THE LID?
Cleaning with Less Water
Washplate
Washplate
Traditional agitator-style
washer
The most striking difference in your new washer is the low-water
washplate wash system. The washer automatically adjusts the
water level to the load size—no water level selector is needed.
Washer with low-water
washplate wash system
Automatic Load Size Sensing
Once you start the cycle, the lid will lock, and the washer will
begin the sensing process to determine the correct water level
for the load. This may take several minutes before water is
added. You will nd a step-by-step description in the “Cycle
Status Lights” section.
You will hear the motor turn the basket in short pulses to
thoroughly wet the load. This low-water wash method uses
less water and energy compared to a traditional agitator-style
washer.
Choosing the Right Detergent
Use only High Efciency detergents. The package will be
marked “HE” or “High Efciency.” Low-water washing creates
excessive sudsing with a regular non-HE detergent. Using
regular detergent will likely result in longer cycle times and
reduced rinsing performance. It may also result in component
failures and noticeable mold or mildew. HE detergents are made
to produce the right amount of suds for the best performance.
Follow the manufacturer’s instructions to determine the amount
of detergent to use.
Load garments in loose heaps evenly around the washplate.
Do not load garments directly over the center of the washplate;
when loaded, the center of the washplate should be visible.
Use only High Efciency (HE) detergent.
Concentrated Cleaning
Low-water cleaning means concentrated cleaning. Rather
than diluting detergent as done in an agitator-style washer,
this washer delivers the detergent directly to the soils.
Normal Sounds
You Can Expect
At different stages of the wash cycle, you may hear sounds and
noises that are different from those of your previous washer.
For example, you may hear a clicking and hum at the beginning
of the cycle, as the lid lock goes through a self-test. There
will be different kinds of humming and whirring sounds as the
washplate moves the load. And sometimes, you may hear
nothing at all, as the washer determines the correct water level
for your load or allows time for clothes to soak.
As the washer dampens and moves the load, the level of the
garments will settle in the basket. This is normal, and does not
indicate that more garments should be added.
IMPORTANT: You will not see a washer basket full of water as
with your past agitator-style washer. It is normal for some of the
load to be above the water line.
3
CONTROL PANEL AND FEATURES
1
1
WASH TEMPERATURE
Temperature Control senses and maintains uniform water
temperatures by regulating incoming hot and cold water.
Select a wash temperature based on the type of fabric
and soils being washed. For best results and following the
garment label instructions, use the warmest wash water safe
for your fabric.
•Warmandhotwaterwillbecoolerthanwhatyourprevious
washer provided.
•Eveninacoolwaterwash,somewarmwatermaybe
added to the washer to maintain a minimum temperature.
2
OPTIONS
The following options may be added to most cycles.
See “Cycle Guide” for additional details.
EXTRA RINSE
This option can be used to automatically add a second
rinse to most cycles.
FABRIC SOFTENER
This option must be selected if using fabric softener
during a cycle. It ensures that fabric softener is added at
the correct time in the rinse for even distribution.
FABRIC SOFTENER with EXTRA RINSE
This option turns on both the Fabric Softener and the
Extra Rinse options.
3
STAIN TREAT
This option provides enhanced cleaning action for tough
stains. It will add additional agitation and soak time to the
cycle.
4
WASH CYCLE KNOB
Use the Wash Cycle knob to select available cycles on your
washer. Turn the knob to select a cycle for your laundry load.
See “Cycle Guide” for detailed descriptions of cycles.
2 3
4
6
5
START/PAUSE/UNLOCK LID BUTTON
Press to Start the selected cycle; press again to Pause the
cycle and unlock the lid.
NOTE: If the washer is spinning, it may take several
minutes to unlock the lid. Press and hold 3 seconds
to Cancel a cycle.
6
CYCLE STATUS LIGHTS
The Cycle Status Lights show the progress of a cycle. At
each stage of the process, you may notice sounds or pauses
that are different from traditional washers.
SENSING FILL
When the START/Pause/Unlock Lid button is pressed,
the washer will rst perform a self-test on the lid lock
mechanism. You will hear a click, the basket will make a
slight turn, and the lid will unlock briey before locking again.
Once the lid has locked the second time, the washer will use
short, slow spins to estimate the load size. These sensing
spins may take 2 to 3 minutes before water is added to the
load and you may hear the hum of these spins. If the sensing
light is on, then washer is working properly. You will hear
the motor turn the basket in short pulses to thoroughly wet
the load. The washer will then move the load briey, pause
to allow water to soak in to the load, and resume adding
water. This process may repeat until the correct amount of
water has been added for the load. You may also hear water
owing through the dispenser, adding detergent to the load.
NOTE: Avoid opening lid during sensing. The sensing
process will start over when the washer is restarted. The
sensing light may also come on during the Soak and Wash
portions of the cycle. This is normal.
WASH
You will hear the motor and washplate moving the load.
Unlike traditional washers, the load is not covered with water.
Low-water cleaning means concentrated cleaning. Rather
than diluting detergent as done in an agitator-style washer,
this washer delivers the detergent directly to the soils. The
motor sounds may change at different stages in the cycle.
The wash time is determined by the selected soil level.
5
4
RINSE
You will hear sounds similar to the wash cycle as the washer
rinses and moves the load. You may hear the motor turning
on briey (short hum) to move the basket while lling. Fabric
softener will be added if the Fabric Softener option was
selected. Some cycles will use a spray rinse.
FINAL SPIN
The washer spins the load at increasing speeds for proper
water removal, based on the selected cycle and spin speed.
CYCLE COMPLETE
Once the cycle is complete, this light will come on. Remove
the load promptly for best results.
LID LOCKED
To allow for proper load sensing and
spinning, the lid will lock and the Lid
Locked light will turn on. This light
indicates that the lid is locked and
cannot be opened.
If you need to open the lid, press
START/Pause/Unlock Lid. The lid will
unlock once the washer movement has
stopped. This may take several minutes
if the load was spinning at high speed.
Press START/Pause/Unlock Lid again to
resume the cycle. Avoid opening the lid
during sensing. The sensing process
will start over when the washer is restarted.
5
CYCLE GUIDE
For best fabric care, choose the cycle that best ts the load being washed.
Not all cycles and options are available on all models.
Items to wash: Cycle: Temperature*: Spin
Sturdy fabrics, colorfast
items, towels, jeans
Sturdy fabrics, colorfast
items, towels, jeans
Cottons, linens, and
mixed garment loads
Light-weight cotton
and cotton blends
No-iron fabrics, cottons,
perm. press, synthetics
Large items such as
sheets, sleeping bags,
jackets, and small
washable rugs
Super
Wash
Normal
Heavy
Normal
Regular
Normal
Light
Casual
Bulky
Items
Hot
Warm
Cool
Cold
Hot
Warm
Cool
Cold
Hot
Warm
Cool
Cold
Hot
Warm
Cool
Cold
Hot
Warm
Cool
Cold
Hot
Warm
Cool
Cold
Speed**:
High
High
High
High
Low
High
Cycle Details:
Provides maximum wash time and action for tough stains
and soils. Use this cycle for heavily soiled or sturdy items.
Water-level sensing process may take longer for some
items than for others because they will absorb more water
than other fabric types.
Use this cycle for heavily soiled or sturdy items. Water-level
sensing process may take longer for some items than for
others because they will absorb more water than other
fabric types. This cycle features a spray rinse.
Use this cycle for normally soiled cottons and mixed fabric
loads. This cycle features a spray rinse.
Use this cycle for light weight cottons that are lightly soiled.
This cycle features a spray rinse.
Use this cycle to wash loads of no-iron fabrics such as
sport shirts, blouses, casual business clothes, permanent
press, and blends.
Use this cycle to wash large items such as jackets and
coats. The washer will ll with enough water to wet down
the load before the wash portion of the cycle begins, and
uses a higher water level than other cycles. Do not tightly
pack basket.
Machine-wash silks,
hand-wash fabrics
Small loads, cottons,
polyester, perm. press
Heavily soiled fabrics Soak Hot
Swimsuits and items
requiring rinsing without
detergent
Dripping wet item or
hand-washed items
No clothes in washer Clean
Delicate Low
Quick
Wash
Rinse &
Spin
Drain &
Spin
Washer
with
®
affresh
Hot
Warm
Cool
Cold
Hot
Warm
Cool
Cold
Warm
Cool
Cold
Cold
N/A
Hot
Warm
Cool
Cold
High
No Spin
High
High
High
Use this cycle to wash lightly soiled garments indicating
“Machine Washable Silks” or “Gentle” cycle on the care
label. Place small items in mesh garment bags before
washing. This cycle uses a higher, preset water level.
Use this cycle to wash small, lightly soiled loads of 2–3 items
that are needed in a hurry. This cycle features a spray rinse.
Use this cycle to soak small spots of set-in stains on fabrics. The
washer will use intermittent agitation and soaking. After time has
expired, water will drain, but the washer will not spin. Cycle is
complete.
Combines a rinse and high-speed spin for loads requiring
an additional rinse cycle or to complete a load after power
interruption. This cycle uses a higher, preset water level.
Also use for loads that require rinsing only.
This cycle uses a spin to shorten drying times for heavy
fabrics or special-care items washed by hand. Use this
cycle to drain washer after cancelling a cycle or completing
a cycle after a power failure.
Use this cycle every 30 washes to keep the inside of your
washer fresh and clean. This cycle uses a higher water level.
Use with affresh® washer cleaner tablet or liquid chlorine
bleach to thoroughly clean the inside of your washer. This
cycle should not be interrupted. See “Washer Care” in
Washer Maintenance.
IMPORTANT: Do not place garments or other items in the
washer during the Clean Washer with affresh® cycle. Use this
cycle with an empty wash tub.
*All rinses are cold.
**Spin speed is integrated into the cycle and cannot be selected.
6
USING YOUR WASHER
Sort and prepare your laundry
1.
2. Add HE detergent
■ Empty pockets. Loose change, buttons, or any small
object can pass under the washplate and become trapped,
causing unexpected sounds.
■ Sort garments by recommended cycle, water temperature,
and colorfastness.
■ Separate heavily soiled garments from lightly soiled.
■ Separate delicate garments from sturdy fabrics.
■ Do not dry garments if stains remain after washing,
because heat can set stains into fabric.
■ Treat stains promptly.
■ Close zippers, fasten hooks, tie strings and sashes, and
remove non-washable trim and ornaments.
■ Mend rips and tears to avoid further damage to garments
during washing.
Helpful Tips:
■ When washing water-proof or water-resistant items, load
evenly. See “Cycle Guide” for tips and more information on
using the Bulky Items cycle.
■ Use mesh garment bags to help avoid tangling when
washing delicate or small garments.
■ Turn knits inside out to avoid pilling. Separate lint-takers
from lint-givers. Synthetics, knits, and corduroy fabrics will
pick up lint from towels, rugs, and chenille fabrics.
NOTE: Always read and follow fabric care label instructions to
avoid damage to your garments.
Add a measured amount of HE
detergent into the basket.
IMPORTANT: Use only High Efciency
detergents. The package will be marked “HE” or “High
Efciency.” Low-water washing creates excessive sudsing
with a regular non-HE detergent. Using regular detergent
will likely result in longer cycle times and reduced rinsing
performance. It may also result in component failures and
noticeable mold or mildew. HE detergents are made to
produce the right amount of suds for the best performance.
Follow the manufacturer’s instructions to determine the
amount of detergent to use.
Using Oxi or color-safe bleach:
If using an Oxi or color-safe bleach laundry boost product,
add to the bottom of the washer basket before adding
clothes.
7
3. Load laundry into washer
5. Add fabric softener
Load garments in loose heaps evenly
around the washplate. Do not load
garments directly over the center of the
washplate; when loaded, the center of
the washplate should be visible. Try
mixing different sized garments to
reduce tangling.
IMPORTANT: Garments need to move
freely for best cleaning and to reduce wrinkling
and tangling.
4. Add liquid chlorine bleach to
dispenser
Liquid
Liquid
Chlorine Bleach
Chlorine Bleach
This washer has been designed to allow
the use of the Downy Ball® to dispense
fabric softener in the rinse cycle. Pour a
measured amount of Downy® liquid fabric softener into the
Downy Ball®, pull the ring tightly to seal it, and place on top
of load. Always follow manufacturer’s directions for correct
amount of fabric softener based on your load size. Then
select Fabric Softener option. The Downy Ball® will
automatically release the fabric softener during the
rinse cycle. For questions on using the Downy Ball® call
1-800-688-7638 or visit www.downy.com.
IMPORTANT: Fabric Softener option must be selected to
ensure proper distribution at correct time in cycle. Do not
overll or dilute.
Adding Liquid Fabric Softener Manually to Wash Load
During the nal rinse, wait until the washer has completed
lling, press the START/Pause/Unlock Lid button to Pause
the washer. Lift the lid and add the measured recommended
amount of liquid fabric softener. Do not allow liquid fabric
softener to spill, splash, drip, or run into the basket or on load.
Do not use more than the recommended amount. Close the lid
and press the START/Pause/Unlock Lid button again to start
the washer.
IMPORTANT: Fabric Softener option must be selected to
ensure proper distribution of the fabric softener during the
rinse portion of the cycle.
6. Select cycle
Do not overll, dilute, or use more than 1 cup (250 mL). Do
not use color-safe bleach or Oxi products in the same cycle
with liquid chlorine bleach.
8
Turn cycle knob to choose your wash cycle.
7. Select wash temperature
Once you select a cycle, select the desired wash temperature
by turning the Wash Temperature knob to the desired setting.
NOTE: Always read and follow fabric care label instructions to
avoid damage to your garments.
Wash Temp Suggested Fabrics
Hot
Some cold water is added to save
energy. This will be cooler than
your hot water heater setting.
Whites and pastels
Durable garments
Heavy soils
8. Select cycle options, if desired
If you would like to add an Extra Rinse, Fabric Softener,
Fabric Softener with Extra Rinse and/or use the Stain Treat
option, turn the knob for that feature.
9. Press START/Pause/Unlock Lid
to begin wash cycle
Warm
Some cold water will be added, so
this will be cooler than what your
previous washer provided.
Cool Lights
Warm water is added to assist in
soil removal and to help dissolve
detergents.
Cool Darks
Warm water may be added to
assist in soil removal and to help
dissolve detergents.
Cold
This is the temperature from your
faucet. If your tap cold water is
very cold, warm water may be
added to assist in soil removal and
help dissolve detergent.
Bright colors
Moderate to light soils
Colors that bleed
or fade
Light soils
Colors that bleed
or fade
Light soils
Dark colors that
bleed or fade
Light soils
Press the START/Pause/Unlock Lid button to start the wash
cycle. Filling is delayed for several minutes while load balance
is sensed. When the cycle has nished, the Cycle Complete
indicator will light. Promptly remove garments after cycle has
completed to avoid odor, reduce wrinkling, and rusting of
metal hooks, zippers, and snaps.
Unlocking the lid to add garments:
If you need to open the lid to add 1 or 2 missed garments:
Press START/Pause/Unlock Lid; the lid will unlock once
the washer movement has stopped. This may take several
minutes if the load was spinning at high speed. Then close lid
and press START/Pause/Unlock Lid again to restart the cycle.
If lid is left open for more than 10 minutes the water will pump
out automatically.
Delay in water fill
Filling is delayed for 2 to 3 minutes to check for load
unbalance. You will hear the hum of the spin prior to lling.
This is normal operation.
9
WASHER MAINTENANCE
WATER INLET HOSES
Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Periodically inspect and replace inlet hoses
if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of
replacement on the label with a permanent marker.
NOTE: This washer does not include inlet hoses. See the
“Installation Instructions” for more information.
WASHER CARE
Recommendations to Help Keep Your Washer Clean
and Performing at its Best
1. Always use High Efciency (HE) detergents and follow the
HE detergent manufacturer’s instructions regarding the
amount of HE detergent to use. Never use more than the
recommended amount because that may increase the rate
at which detergent and soil residue accumulate inside your
washer, which in turn may result in undesirable odor.
2. Use warm and hot wash water settings sometimes (not
exclusively cold water washes), because they do a better
job of controlling the rate at which soils and detergent
accumulate.
3. Always leave the washer lid open between uses to help dry
out the washer and prevent the buildup of odor-causing
residue.
Cleaning Your Top Loading Washer
Read these instructions completely before beginning the
routine cleaning processes recommended below. This Washer
Maintenance Procedure should be performed, at a minimum,
once per month or every 30 wash cycles, whichever occurs
sooner, to control the rate at which soils and detergent may
otherwise accumulate in your washer.
Cleaning the Inside of the Washer
To keep your washer odor-free, follow the usage instructions
provided above, and use this recommended monthly cleaning
procedure:
Clean Washer Cycle
This washer has a special cycle that uses higher water volumes
in combination with affresh® Washer Cleaner or liquid chlorine
bleach to clean the inside of the washer.
Begin procedure
1. affresh® Washer Cleaner Cycle Procedure (Recommended
for Best Performance):
a. Open the washer lid and remove any clothing or items.
b. Place an affresh® Washer Cleaner tablet in the bottom
of the washer basket.
c. Do not place an affresh® Washer Cleaner tablet
in the detergent dispenser.
d. Do not add any detergent or other chemical to the
washer when following this procedure.
e. Close the washer lid.
f. Select the CLEAN WASHER cycle.
WASHER CARE (cont.)
g. Press the START/Pause/Unlock Lid button to begin
the cycle. The Clean Washer Cycle Operation is
described below.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, press POWER/CANCEL. (For models
with no Power/Cancel button, press and hold START/
Pause/Unlock Lid for three seconds). After the Clean
Washer cycle has stopped, run a RINSE & SPIN cycle to
rinse cleaner from washer.
2. Chlorine Bleach Procedure (Alternative):
a. Open the washer lid and remove any clothing
or items.
b. Add 1 cup (236 mL) of liquid chlorine bleach
to the bleach compartment.
NOTE: Use of more liquid chlorine bleach than is
recommended above could cause washer damage
over time.
c. Close the washer lid.
d. Do not add any detergent or other chemical
to the washer when following this procedure.
e. Select the CLEAN WASHER cycle.
f. Press the START/Pause/Unlock Lid button to begin
the cycle. The Clean Washer Cycle Operation is
described below.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, press POWER/CANCEL. (For models
with no Power/Cancel button, press and hold START/
Pause/Unlock Lid for three seconds). After the Clean
Washer cycle has stopped, run a RINSE & SPIN cycle to
rinse cleaner from washer.
Description of Clean Washer Cycle Operation:
1. This cycle will ll to a water level higher than in normal
wash cycles to provide rinsing at a level above the water
line for normal wash cycle.
2. During this cycle, there will be some agitation and
spinning to increase the removal of soils.
After this cycle is complete, leave the lid open to allow
for better ventilation and drying of the washer interior.
Cleaning the Dispensers
After a period of using your washer, you may nd some
residue buildup in the washer’s dispensers. To remove
residue from the dispensers, wipe them with a damp cloth
and towel dry. Do not attempt to remove the dispensers or
trim for cleaning. The dispensers and trim are not removable.
If your model has a dispenser drawer, however, remove the
drawer and clean it before or after you run the Clean Washer
cycle. Use an all-purpose surface cleaner, if needed.
Cleaning the Outside of the Washer
Use a soft, damp cloth or sponge to wipe away any spills.
Use only mild soaps or cleaners when cleaning external
washer surfaces.
IMPORTANT: To avoid damaging the washer’s nish, do not
use abrasive products.
10
NON-USE AND VACATION CARE
REINSTALLING/USING WASHER AGAIN
Operate your washer only when you are home. If moving,
or not using your washer for a period of time, follow these
steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer, to avoid ooding due
to water pressure surge.
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets; disconnect and drain water
inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run
washer on RINSE & SPIN cycle for about 30 seconds to
mix antifreeze and remaining water.
3. Unplug washer or disconnect power.
TRANSPORTING YOUR WASHER
1. Shut off both water faucets. Disconnect and drain water
inlet hoses.
2. If washer will be moved during freezing weather, follow
“Winter Storage Care” directions before moving.
3. Disconnect drain from drain system and drain any
remaining water into a pan or bucket. Disconnect drain
hose from back of washer.
4. Unplug power cord.
5. Place inlet hoses and drain hose inside washer basket.
6. Drape power cord over edge and into washer basket.
7. Place packing tray from original shipping materials back
inside washer. If you do not have packing tray, place
heavy blankets or towels into basket opening. Close lid
and place tape over lid and down front of washer. Keep
lid taped until washer is placed in new location.
To reinstall washer after non-use, vacation, winter storage,
or moving:
1. Refer to “Installation Instructions” to locate, level, and
connect washer.
2. Before using again, run washer through the following
recommended procedure:
To use washer again:
1. Flush water pipes and hoses. Reconnect water inlet
hoses. Turn on both water faucets.
2. Plug in washer or reconnect power.
3. Run washer through BULKY ITEMS cycle to clean
washer and remove antifreeze, if used. Use only HE
High Efciency detergent. Use 1/2 the manufacturer’s
recommended amount for a medium-size load.
11
Loading...