Amana RMS10T General Manual

Quick Start Reference Guide

Refer to Product Safety Manual for Safety Statements

Complete Owner’s Manual available online

Oven Wall Clearances

A—For North American (UL/CSA) models, allow at least

3” (7.2 cm) of clearance around top of oven. For International (50 Hz) models, allow at least 12” (30 cm) of clearance around top of oven. Proper air

ow around oven cools electrical components. With restricted air ow, oven may not operate properly and

life of electrical parts is reduced.

B—Allow at least 3” (7.2 cm) between air discharge on

back of oven and back wall.

C—Allow at least 3” (7.2 cm) of clearance around side of

oven. One side of oven must be open.

So...how do I use it? (Electronic Control)

Manual Operation

To cook food using a specic entered time and power level:

Preprogrammed Pads

To cook food using

preprogrammed cooking

sequences:

1. Open oven door and place food in oven. Close door.

2. Press desired pad.

3. Oven begins to cook.

4. At end of cooking cycle oven beeps and shuts off.

X2 Programming

To change the cooking factor:

1. Open oven door.

2. Press and hold pad 1 for approximately 5 seconds.

3. Press pad to be reprogrammed.

4. Press the X2 pad.

5. Press a numbered pad to change the cooking factor.

• Cooking factor can be set from

10% to 100%.

• Default is 80%.

• Pad 5 would change the

cooking factor to 50%.

6. Press START changes.

The switching operation of this microwave oven can cause voltage uctuations on the supply line. The operation of this oven under

unfavorable voltage supply conditions can have adverse effects. This device is intended for the connection to a power supply system with a maximum permissible system impedance Zmax of 0.2 Ohms at the interface point of the user’s supply. The user has to

ensure that this device is connected only to a power supply system which fullls the requirement above. If necessary, the user

can ask the public power supply company for the system impedance at the interface point.

pad to save

1. Open oven door and place food in oven. Close door.

2. Press TIME ENTRY

3. Press a power level pad to change power level if desired (some models).

• COOK LEVEL displays with the power setting.

4. If stage cooking is desired, press TIME ENTRY 2 through 4.

5. Press START

6. At end of cooking cycle oven beeps and shuts off.

pad and enter cooking time.

pad.

Programming Items

1. Open oven door.

2. Press and hold pad 1 for approximately 5 seconds.

3. Press pad to be reprogrammed.

4. Enter cooking time by using the number pads.

5. Press a power level

6. If stage cooking is desired, press TIME ENTRY

• Display briey shows the stage number.

• Display changes to cook time and power level for the next stage.

7. Enter cook time and power level as in steps 4 and 5 (some models).

• To enter another cooking stage for that pad, press TIME ENTRY

again.

• Up to four different stages can be programmed (some models).

8. Press START

NOTE: T

o discard changes, press STOP/RESET pad or close oven door.

pad to change power level if desired.

pad to set new programming changes to the pad.

X2 Pad

1. Open oven door and place food in oven. Close door.

2. Press X2 pad.

3. Press desired preprogrammed pad or pad sequence.

4. Oven begins cooking. Displayed cooking time is the total of original

cooking time and added X2 time.

pad and repeat steps

pad.

pad

Quick Start Reference Guide

Numbered Pads Display Options (Factory Settings in Bold)

End of Cycle Beep

OP:10

OP:11

OP:12

3 second beep.

Continuous beep until door is opened.

5 beep bursts until door is opened.

Key Beep Volume

OP:20

OP:21

OP:22

OP:23

Eliminates beep.

Sets volume to low.

Sets volume to medium.

Sets volum e to hig h.

Key Beep

OP:30

OP:31

Prevents beep when pad is pressed.

Allows beep when pad is pressed.

Active Display

OP:40

OP:41

OP:42

OP:43

15 seconds after oven door is opened, keyboard disabled.

30 seconds after oven door is opened, keyboard disabled.

1 minute after oven door is opened, keyboard disabled.

2 minutes after oven door is opened, keyboard disabl ed.

On-the Fly Cooking

OP:50

OP:51

Prevents dierent pre-programmed pads to be activated during cooking.

Reset to Ready Mode

OP:60

OP:61

Opening oven door does not reset oven back to ready mode.

(some mo dels)

Maximum Heating Time

OP:70

OP:71

Allows 60 minutes of heating time (some models).

Allows 10 minutes of heating time.

Manual Operation

OP:80

OP:81

Allows use of preprogrammed pads only.

Allows use of m anual time entry and preprog rammed pads.

(some mo dels)

Double Digit Operation

OP:90

OP:91

Allows 10 (0-9) preprogramm ed pads.

Allows 100 (00-99) preprogrammed pads.

Allows different pre-programmed pads to be activated during cooking.

Opening oven door resets oven back to ready mode.

Refer to Product Safety Manual for Safety Statements

DO NOT power spray

No metal pans

Complete Owner’s Manual available online

Can I change an option?

Options such as single or double pad programming, beep volume, and maximum cooking time can be changed to suit individual preferences.

To change options:

1. Open oven door.

• If door is closed or STOP/RESET

complete, changes are discarded and microwave exits programming mode.

2. Press and hold pad 2 for approximately 5 seconds.

• This begins options mode.

• Microwave will beep and 0P: displays.

3. Press number pad that controls option to be changed.

• See table below for options.

• Current option will display.

4. Press number pad again to change the option.

• Each time pad is pressed, option will change.

• Match code displayed with code for desired option.

5. Press START

pad to save changes.

• To change additional options, repeat steps 3 and 4.

• Changes appear after door is closed or STOP/RESET

pressed.

pad is pressed before programming is

pad is

Part No.20037402 Revised 7/10

For full product documentation visit:

www.acpsolutions.com

Cedar Rapids, Iowa 52404

 2010 ACP , Inc.