Amana BB20V1E, BB20V1PS, BB20V1S, BB20V1W, BB20VE Owner's Manual

...

Bottom Freezer Refrigerator Owner's Manual

English ................................................................... 2

Español................................................................ 21

Français ............................................................... 41

Keep these instructions for future reference. Be sure this manual stays with refrigerator.

Contents

Electrical Requirements ..................................................... 2

Model Identification ............................................................ 2

Service ............................................................................... 2

Asure™ Extended Service Plan ......................................... 2

Proper Disposal of your Refrigerator ................................. 3

Cutout Dimensions............................................................. 3

Installation Instructions ....................................................... 3

Door Reversal (Contour door models) ........................ 3

Door Reversal (Front-mounted handle) ...................... 3

Door Reversal (Side-mounted handle) ....................... 5

Install Decorator Panels .............................................. 7

Connect Ice Maker Water Supply Line

(some models) ............................................................ 8

Leveling Refrigerator .................................................. 9

Installation Checklist ........................................................ 10

Controls............................................................................ 11

Fresh Food and Deepfreeze

Setting Controls ........................................................ 11

Fresh Food Features ........................................................ 11

Spillsaver™ Shelves ................................................. 11

Deli Port™ ................................................................. 11

Drawers..................................................................... 12

Covered Storage Bucket ........................................... 12

Dairy Centers ............................................................ 12

Door Buckets............................................................. 12

Door Shelf ................................................................. 13

Adjustable Dividers ................................................... 13

Tall Package Retainer ............................................... 13

Deepfreeze

Automatic Ice Maker(some models) .......................... 13

Ice Service Rack(some models) ............................... 13

Slideout Shelf(some models) .................................... 14

Vertical Shelf Divider(some models) ......................... 14

Pivot Bin™ ................................................................ 14

Care and Cleaning........................................................... 14

General ..................................................................... 14

Odor Removal ........................................................... 14

Adhesives ................................................................. 15

Door Gaskets ............................................................ 15

Condenser Coils ....................................................... 15

Glass Shelves ........................................................... 15

Light Bulbs ................................................................ 15

Energy Tips ...................................................................... 15

Vacation Tips .................................................................... 16

Normal Operating Sounds ............................................... 16

Before Calling For Service ............................................... 17

Warranty ........................................................................... 19

Note: Translation may sometimes cause variations in meaning. In all cases where meaning varies, the most accurate meaning will be the English version of this document.

Features ...................................................... 13

Controls ..................... 11

Recognize this symbol as a safety

precaution.

Electrical Requirements

WARNING

To avoid electrical shock which could cause severe personal injury or death:

• Do not cut or remove grounding prong from plug.

• Do not use a two-prong adapter.

• Do not use an extension cord.

• Do not remove warning tag from power cord.

• Follow all grounding and connection instructions.

This refrigerator is equipped with a three-prong (grounding) plug for protection against possible shock hazards. If a two-prong wall receptacle is encountered, contact a qualified electrician and have the two-prong wall receptacle replaced with a properly grounded three-prong wall receptacle in accordance with the National Electrical Code.

Refrigerator is designed to operate on a separate 103 to 126 volt, 15 amp., 60 cycle line.

Model Identification

Thank you for purchasing this Amana® refrigerator. Please read this Owner's Manual thoroughly. This manual provides proper maintenance information. Any questions, call the Consumer Affairs Department at 1-800-843-0304 inside U.S.A. and 1-319-622-5511 outside U.S.A, or contact us on the internet at www.amana.com.

Complete registration card and promptly return. If registration card is missing, call the Consumer Affairs Department.

When contacting Amana Appliances, provide product information. Product information is on the serial plate, located on the ceiling of refrigerator section. Record the following information:

Model Number: Manufacturing Number: S/N or Serial Number: Date of purchase: Dealer’s name and address:

Service

Keep a copy of sales receipt for future reference or in

case warranty service is required. Any questions or to locate an authorized servicer, call 1-800-NAT-LSVC (1800-628-5782) inside U.S.A. 319-622-5511 outside U.S.A.,

or contact us on the internet at www.amana.com.

Warranty service must be performed by an authorized servicer. Amana, also recommends contacting an authorized servicer if service is required after warranty expires.

Note About Contour Door Reversal:

Only a qualified servicer can reverse this door. To have doors reversed, please call 1-800-843-0304. There is a

fee charged for this service.

Asure™ Extended Service Plan

Amana offers long-term service protection for this new refrigerator. Asure™ Extended Service Plan is specially designed to supplement Amana’s strong warranty. This plan covers parts, labor, and travel charges.

For more information visit our web site:

www.amana.com

DANGER

Proper Disposal of your Refrigerator

IMPORTANT: Child entrapment and suffocation are not

problems of the past. Junked or abandoned refrigerators are still dangerous—even if they sit for "just a few days". If you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents.

BEFORE YOU THROW AWAY YOUR OLD REFRIGERATOR OR FREEZER:

• Take off the doors.

• Leave the shelves in place so children may not easily climb inside.

Cutout Dimensions

IMPORTANT:

• Save all screws for reuse.

• For plug removal requiring use of flat blade screwdriver

or putty knife, blade of tool must be covered with

masking tape to avoid damage to refrigerator finish. For plugs using a screwdriver or nut driver style

head, use appropriate tool to avoid damage to plugs.

CAUTION

To avoid personal injury or property damage caused by refrigerator tipping, stabilizing leg must be firmly

against floor.

Door Reversal (Contour door model)

Only a qualified servicer can reverse this door. To have doors reversed, please call 1-800-843-0304. There is a

fee charged for this service.

Door Reversal (Front mounted handle)

Some installations may require door reversal to achieve full door swing. To reverse door swing direction perform the following steps.

1. Remove refrigerator handle:

• Remove handle screw from top handle trim. Pry up edge of handle trim using a putty knife with the blade covered with masking tape. Remove handle from door by removing 1 remaining mounting screw at each end of handle.

• Remove 1 plug from top hinge side of door and 2 from front hinge side of door. Transfer plugs to opposite side of door to fill empty mounting holes.

Single Installation

H • 69" with 12" deep cabinets above refrigerator.

• 70" with 24" deep cabinets above refrigerator. W 36" D 24"

Installation Instructions

Proper installation will ensure that this refrigerator operates most efficiently. Amana cannot be responsible for improper installation.

Tools Required

/16" hex nut driver Phillips screwdriver

/8 " hex nut driver Blade screwdriver

/4 " hex nut driver

Putty knife (blade covered by masking tape)

A Handle trim C Screws B Handle D Plugs

2. Remove freezer door handle:

• Open freezer door 90°. Locate two notches on back of freezer handle. Insert flat screwdriver blade or putty knife blade wrapped in masking tape. Pry up back edge of handle cap and remove from handle.

• Remove handle from door by removing two mounting screws.

• Remove 2 plugs from hinge side of freezer door and transfer to opposite side to fill holes left from handle removal.

A Handle C Screws B Handle cap D Plug

3. Remove doors:

• Remove top hinge cover. Top hinge cover snaps off. While supporting refrigerator door, remove top hinge and hinge shim using positive positioning shim from cabinet. Remove and retain all shims.

• Keep adhesive surface of shim free of dirt and dust until ready to replace during top hinge reversal. Contamination of adhesive surface will prevent proper reinstallation.

/16” hex nut driver. Peel

C D

A Phillips screws C Center hinge shim B Center hinge

6. Reverse bottom hinge pin:

• Remove toe grille by grasping both ends and pulling straight out from unit. Grille snaps free.

A Top hinge cover D Hinge shim

/16" hex nut screws E Positive positioning

B C Top hinge shim

• Remove refrigerator door by lifting door off center hinge pin. Inspect door to verify all shims are with pin assembly.

• Remove center hinge pin using ¼" hex nut driver. Due to tight fit of pin, firm pressure may need to be applied. Remove and retain all washer shims.

• Remove freezer door by lifting door off bottom hinge pin.

A Washer shims C Center hinge B Center hinge pin

4. Remove internal support rod(some models):

• Some models have an internal support rod

installed in the hinge socket of door. If

below)

present, remove and retain for later replacement.

A Support rod (some models)

5. Reverse center hinge:

• Remove center hinge bracket and shims by removing screws using a Phillips screwdriver.

• Remove 3 screws opposite of center hinge and transfer to opposite side of cabinet.

• Install bracket on opposite side of cabinet with shims.

(see

A Toe grille

• Exchange hinge pin from bottom hinge assembly with outward hinge plug from opposite bottom hinge assembly.

A Hinge pin B Hinge plug

7. Reverse door stops:

• Locate door stop at bottom edge of refrigerator door. Unscrew two Phillips screws to remove door stop. Remove the two Phillips screws on opposite edge of door. Mount door stop on opposite side. Replace remaining screws in empty mounting holes.

• Repeat the above instructions to reverse door stop on freezer door.

A Screws B Door stop

8. Replace doors:

• Rehang freezer door by setting freezer door hinge hole on bottom hinge pin.

• While supporting freezer door, insert internal support rod into hinge socket, and install center hinge pin into the center hinge bracket.

• Tighten down center hinge pin with a ¼" hex nut driver to hold door in place. Make sure fit is snug.

• Locate 3 plugs at top of cabinet. Transfer plugs to holes left by hinge removal.

• Assemble top hinge, hinge shim(s), and positioning shim together. Attach loosely to opposite side of cabinet to allow for door clearance.

• Set refrigerator door on center hinge pin.

• While supporting refrigerator door, use a dime to

space door

/16" (18 mm) from cabinet. Use plastic shims behind center hinge to provide more space if required.

• Handle side of door should be approximately

/8"

(3 mm) higher than hinge side of door. Door will

become level when it is loaded with food.

• Tighten all top hinge screws to secure refrigerator door. Snap on hinge cover.

1/8"

(3 mm)

11/16"

(18 mm)

9. Reinstall handles:

• Mount refrigerator handle on opposite side of door using mounting screws removed in previous step.

• Snap handle trim into place and replace screw.

• Mount freezer handle to opposite side of door using

mounting screws removed in previous step.

• Angle front edge of handle cap downward toward back lip of freezer handle. Verify bottom tab on freezer cap slides under rear lip of freezer handle. Snap rear edge of handle cap in place.

10. Check unit for proper leveling following instructions in section titled

Leveling Refrigerator

, starting with step

three.

1. Remove top refrigerator door cap and hinge cover:

• Remove 3 Phillips screws to release top door cap.

A Hinge cover C Handle B Top door cap

• Remove hinge cover by unscrewing one Phillips screw.

2. Remove doors:

• Use

/16" hex nut driver to remove top hinge screws. Peel positive positioning shim from cabinet. Remove and retain all shims.

• Keep adhesive surface of shim free of dirt and dust until ready to replace during top hinge reversal. Contamination of adhesive surface will prevent

proper reinstallation.

B C

Door Reversal (Side mounted handles)*

*Non contour doors only

Tools Required

#1 & #2 Phillips Head Screw Driver Flat blade screwdriver Rubber mallet ¼” hex nut driver

/8” hex nut driver

/16” hex nut driver

/32” hex nut driver

IMPORTANT:

• Keep all discarded parts with literature assembly.

• Save all screws for reuse.

• For plug removal requiring use of flat blade screwdriver

or putty knife, blade of tool must be covered with masking tape to avoid damage to refrigerator finish. For plugs using a screwdriver or nut driver style

head, use appropriate tool to avoid damage to plugs.

A Hinge cover D Top hinge shim

/16" hex nut screws E Positive positioning shim

B C Top hinge

• Remove refrigerator door by lifting door off center hinge pin. Inspect door to verify all shims are with

pin assembly.

• Remove center hinge pin using ¼" hex nut driver. Due to tight fit of pin, firm pressure may need to be

applied. Remove and retain all washer shims.

A Washer shims C Center hinge B Center hinge pin

• Remove freezer door by lifting door off bottom hinge pin.

• Some models have an internal support rod installed in the hinge socket of door. If

below)

present, remove and retain for later replacement.

(see

• Unscrew door extension on top of door with Phillips screw driver. Flip door extension so notched corner turns in toward interior of door. Reinstall with screws.

A Support rod (some models)

3. Reverse center hinge:

• Remove center hinge bracket and shims by removing screws using a Phillips screwdriver.

• Remove 3 screws opposite of center hinge and transfer to opposite side of cabinet.

• Install bracket on opposite side of cabinet with shims.

A Phillips screws C Center hinge shim B Center hinge

4. Reverse bottom hinge pin:

• Remove toe grille by grasping both ends and pulling straight out from unit. Grille snaps free.

A Before B After C Door extension

6. Reverse handles and trim:

• Remove screws from bottom door cap of refrigerator and freezer door with screwdriver.

• Using a soft rubber mallet, tap bottom of handle upward toward top of door. Handle will slide up approximately ¾" and release from door.

• Using a soft rubber mallet, tap bottom of door hinge trim upward toward top of door. Trim will slide up approximately ¾" and release from door.

• Remove plastic tab on top of trim*. Return tab to literature assembly. Locate alternate tab piece in literature assembly and place this in notch at opposite end of trim.

* In stainless steel models plastic tab is not

required. Replace trim with alternate trim shipped with unit.

A Toe grille

• Exchange hinge pin from bottom hinge assembly with outward hinge plug from opposite bottom hinge assembly.

A Hinge pin B Hinge plug

5. Remove door stops and reverse door extensions:

• Locate door stop and bottom of refrigerator door and freezer door. Remove with Phillips screwdriver.

A Bottom door cap C Door stop B Screws

Left mounted handle

• Replace bottom door cap.

• Attach door stop under the hinge side of the door

using Phillips screws.

• Install hinge trim by locating notches on the inside of trim(make sure plastic tab insert is facing bottom of door). Align notches of trim with metal mounting tabs on opposite side of door. Slide trim down until piece locks into place. Tap top of trim with rubber mallet to insure snug fit.

Right mounted handle

• Reinstall handle on opposite side locating notches on inside of handle trim. Slide handle down until handle locks into place. Tap top of handle with rubber mallet to insure snug fit. End of trim should

be flush with top of door.

• While supporting refrigerator door, use a dime to space door shims behind center hinge to provide more space if required.

• Handle side of door should be approximately (3 mm) higher than hinge side of door. Door will

become level when it is loaded with food.

• Tighten all top hinge screws to secure refrigerator door. Snap on hinge cover.

/16" (18 mm) from cabinet. Use plastic

/8"

1/8"

(3 mm)

A Trim C Mounting tabs B Refrigerator handle

• Fasten top door cap securely over top of door by replacing screws.

• Remove top door cap of freezer from top of freezer door with screwdriver.

• Transfer hinge socket plug on top of freezer door to opposite hinge socket.

• To reverse freezer handle and trim, follow step 5. Note: Freezer trim does not have plastic tab or alternate trim for stainless steel models.

• Replace top door cap with screwdriver.

A Top door cap E Bottom door cap B Hinge socket plug F Door stop C Handle G Trim D Mounting tabs

7. Replace doors:

• Rehang freezer door by setting freezer door hinge socket on bottom hinge pin.

• While supporting freezer door, insert internal support rod into hinge socket, and install center hinge pin into the center hinge bracket.

• Tighten down center hinge pin with a ¼" hex nut driver to hold door in place. Make sure fit is snug.

• Locate 3 plugs at top of cabinet. Transfer plugs to holes left by hinge removal.

• Locate new top hinge found in literature assembly. Assemble top hinge, hinge shim(s), and positioning shim together. Attach loosely to opposite side of cabinet to allow for door clearance.

• Set refrigerator door on center hinge pin.

11/16"

(18 mm)

8. Check unit for proper leveling following instructions in section titled

three.

Leveling Refrigerator

, starting with step

Install Decorator Panels (some models)

WARNING

To avoid personal injury or property damage, fresh food panel should not weigh more than 30 lbs (14 kgs) and freezer panel should not weigh more than 15 lbs (7 kgs).

If raised panels are used, allow 2½" minimum clearance between raised edge of panel and refrigerator handle.

A2½" clearance from raised panel edge to edge of door. B Raised panel–41" x 35 C Raise panel–23

/8" (104 cm x 90.5 cm)

/16" x 35 5/8" (60.2 cm x 90.5 cm)

1. Remove top door cap and handle of refrigerator door. Slide panel into groove provided by bottom door cap. When replacing handle, press panel flat against door and slide handle down so that overlapping edge of handle slides over panel to secure it. Replace door cap.

A Refrigerator door panel B Refrigerator handle

2. Open door 90° and unscrew freezer top door cap. Close door. Slide trim forward until free from door. Open door. Remove door handle per step 5.

3. Slide panel into groove provided by bottom door cap. When replacing handle, press panel flat against door and slide handle down so that overlapping edge of handle slides over panel to secure it. Replace door cap and screws.

Important

• Before connecting water supply, contact a plumber to connect copper tubing to household plumbing in compliance with local codes and ordinances.

• Amana does not recommend using a self-piercing, or

/16" saddle valves! Both reduce water flow, become plugged with sediment over time and may cause leaks if repair is attempted. The correct type of shut-off valve requires a prior to valve attachment. Amana is not responsible for property damage caused by improper water connection.

Materials Required

¼" O.D. (6 mm) flexible copper tubing is required. Length of copper tubing must reach from water supply connection to water valve inlet port on back of refrigerator, plus additional 8'(2 m) of tubing for a service loop. A service loop will allow refrigerator to be pulled away from the wall without disconnecting tubing.

Procedure

1. Remove plastic cap from water valve inlet port.

/4" hole to be drilled in the water supply pipe

A Top door cap D Bottom door cap B Handle E Trim C Panel

4. Review

Installation Checklist

Connect Ice Maker Water Supply Line

(some models)

WARNING

To avoid electrical shock which can cause severe personal injury or death, disconnect power to refrigerator before connecting water supply. After

connecting water supply, connect power.

CAUTION

Observe the following to avoid property damage:

• Make sure water pressure to water valve is between 20 and 100 pounds per square inch.

• Tighten adapter fitting and nuts with pliers and wrenches. Do not overtighten.

• Check for water leaks and correct if necessary before returning refrigerator to normal location. After 24 hours check again for leaks.

A Plastic cap B Water valve inlet

port

2. Place brass nut and brass sleeve on copper tubing. (Brass nut and sleeve are found in your literature packet.) Insert copper tubing into water valve inlet port. Connect brass nut on copper tubing to water valve inlet port. Make sure copper tubing is secure by

pulling on copper tubing.

A "P" clamp D Brass nut B Copper tubing E Water valve inlet C Brass sleeve port

3. Turn on water supply to refrigerator and check for leaks. Correct any leaks at connection. Be careful not to overtighten connection.

4. Create a service loop using extreme care to avoid kinks. Secure copper tubing to refrigerator cabinet with a "P" clamp.

CAUTION

To avoid property damage, protect soft vinyl or other flooring with cardboard, rugs, or other protective

material when moving refrigerator.

Leveling Refrigerator

Some installation may require door reversal to achieve full door swing. If so proceed to leveling your refrigerator.

If your refrigerator requires ice maker water supply connection, proceed to section before leveling refrigerator.

1. Plug in power cord.

2. Move refrigerator into final location.

3. Level refrigerator using a level placed on top of the refrigerator.

• Remove toe grille by grasping both ends and pulling straight out from unit. Grille snaps free.

• The left and right corners of front cabinet base each contain 2 screws to allow individual adjustment of all four corners. Adjust the front and rear of each corner until leveling is complete.

• Turn roller adjustment screws to the right to raise cabinet, or to the left to lower cabinet. Front of refrigerator must be ¼" (6 mm), or ½ bubble on your level, higher than the back of your refrigerator.

• After leveling, turn stabilizing leg (some models) clockwise until firmly against floor.

Door Reversal

Connect Ice Maker Water Supply

section before

A Rear roller adjustment C Stabilizing leg* B Front roller adjustment *some models

• Locate metal clips mounted to inside of toe grille assembly. Hook bottom set of clips inside metal molding beneath freezer. Press forward on upper

part of grille until top portion snaps into place.

A Metal clips

Installation Checklist

This checklist is for personal records only.

Consumer Installer

Doors

Handles are solidly attached to doors. Handle side of door is 1/8" (3 mm) higher than hinge side of door. (Door lowers

when loaded with food.) Doors seal completely to refrigerator cabinet.

Leveling

Refrigerator is tilted 1/4" (6 mm) from front to rear.

Stabilizing legs are against floor.

Toe grille is properly attached to refrigerator.

Ice Maker (some models)

Water supply to refrigerator is turned on. Water leaks are not present at connection between household water supply and

refrigerator. (After 24 hours, consumer should check connection for water leaks.) Ice maker arm is down for ice production. (It may take up to 24 hours for first

harvest of ice.)

Notes

Consumer's Signature

Product Literature

Owner's manual is reviewed including the following information:

• product registration card

• Fresh Food and Deepfreeze® controls

• humidity controlled crisper drawer

• temperature controlled drawer

• normal operating sounds

Installer's Signature

DateInstaller's Company Name/Phone Number

Controls

This refrigerator operates most efficiently in normal household temperatures of 55° to 110°F (13°C to 43°C).

Fresh Food and Deepfreeze® Controls

Fresh Food control is located on upper rear wall of Fresh Food section.

Deepfreeze® control is located on right front ceiling of Deepfreeze® section.

Spillsaver™ Shelves

Spillsaver™ shelves adjust to meet individual storage needs and hold simple spills for easier cleaning.

CAUTION

To avoid personal injury or property damage, handle tempered glass shelves carefully. Shelves may break suddenly if nicked, scratched, or exposed to sudden temperature change.

• Remove shelves by lifting front, releasing hooks from metal track then pulling out.

• Replace shelves by inserting hooks into metal track and lowering front.

Deepfreeze Control

Cold Coldest

When Deepfreeze® control is set to Food nor Deepfreeze® sections will cool. Initially, set both controls to 4. Wait 24 hours for Fresh Food and Deepfreeze® sections to reach desired temperatures. After 24 hours, adjust controls, one number at a time, as desired. 1 is warmest setting and 7 is coldest.

OFF

, neither Fresh

Setting Controls

Set controls precisely using a household thermometer that includes temperatures between -5° to 50°F (-21° to 10°C).

Put thermometer snugly between frozen packages in Deepfreeze® section. Wait 5–8 hours. If Deepfreeze temperature is not 0° to 2°F (-17° to -16°C), adjust control, one number at a time. Check again after 5–8 hours.

Put thermometer in a glass of water in middle of Fresh Food section. Wait 5–8 hours. If Fresh Food temperature is not 38° to 40°F (3° to 4°C), adjust control, one number at a time. Check again after 5–8 hours.

Fresh Food Features

EasyGlide™ shelves pull forward for easy access of items in back.

Deli Port

Deli Port™ provides space saving storage underneath Spillsaver™ shelf and pulls forward for easy access.

• Remove shelf by pulling forward until shelf stops. Push tabs on sides of shelf in and pull shelf forward.

• Replace shelf by inserting shelf into track and sliding back.

™

CAUTION

To avoid property damage, confirm shelf is secure before placing items on shelf.

ATab

Drawers

Humidity Controlled Crisper Drawer

The right drawer is humidity controlled. This drawer keeps produce fresh longer. Wrap produce tightly. Do not wash produce before placing in drawer. Excess moisture could cause produce to spoil prematurely. Do not line drawer with paper towels. Paper towels will retain moisture. Humidity control is located below front shelf trim. Control adjusts humidity in drawer. Slide control to right for produce with leaves such as lettuce, spinach or cabbage. Slide control to left for produce with skins such as cauliflower, corn or tomatoes.

Temperature Controlled Drawer

The left drawer is temperature controlled. This drawer keeps food fresh longer and up to 5°F (3°C) colder than Fresh Food temperature. Use this drawer for deli storage or additional produce storage. Temperature control is located below front shelf trim. Control adjusts amount of air circulating around drawer. Slide control left for normal Fresh Food temperature and right for colder temperature. Ice crystals may form on drawer or food on coldest setting. Cold air can decrease Fresh Food temperature. Fresh Food control may need to be adjusted. Remove shelf and drawers by completing the following steps.

1. Open left* drawer. *For doors hinged on left, open right drawer.

Covered Storage Bucket

Storage bucket has a lid and removable egg tray. When tray is removed, bucket will accept items such as a standard egg carton, ice, etc.

Dairy Centers

Dairy centers provide convenient storage for items such as butter, cheese, etc.

• Remove dairy centers by lifting door, pushing tabs toward center and pulling out.

• Replace dairy centers by sliding in until tabs lock into place and lowering door.

CAUTION

To avoid personal injury or property damage, handle tempered glass shelves carefully. Shelves may break suddenly if nicked, scratched, or exposed to sudden temperature change.

2. Remove shelf by gently pushing up from underneath. Tilt one end up then pull out.

3. Remove left* drawer by lifting front while supporting underneath then pulling out. *For doors hinged on left, remove right drawer.

4. Remove support post at recess in bottom center of Fresh Food section by lifting.

5. Remove other crisper by sliding to opposite wall. Lift front while supporting underneath then pull out.

6. Replace drawers and shelf by reversing steps 1–5.

A Door B Tab

Door Buckets

Door buckets adjust to meet individual storage needs.

• Remove door buckets by pushing tabs toward center and pulling out.

• Replace door buckets by sliding in until tabs lock into place.

A Tabs

DeepfreezeTM Features

Door Shelf

• Remove door shelf by lifting ends and pulling out.

• Replace door shelf by placing shelf on glides and

sliding down.

A Glide

Adjustable Dividers

Adjustable dividers keep items in place and adjust to meet individual storage needs. Divider fits in any Fresh Food door bucket or door shelf.

Frost-Free System

The fresh food and freezer sections are completely frostfree. Defrosting is automatic under normal conditions. Fresh food and freezer sections never have to be defrosted.

Automatic Ice Maker (some models)

• Make sure ice bucket is in place and ice maker arm is down.

A Off position C On position B Ice maker arm

• After freezer section reaches normal temperature, the ice maker fills with water and begins operating. Allow 24–48 hours after installation before first harvest of ice. Ice maker produces 7 to 9 harvests of ice in a 24-hour period under ideal conditions.

• After ice is formed, ice maker drops ice cubes into ice storage bucket. During ice production, ice maker arm raises and lowers. When ice storage bucket is full, ice maker arm turns ice maker off.

Note: Discard first 3 harvests of ice so any impurities left in the water line after installation are not consumed.

• If you wish to stop automatic ice production lift ice maker arm. A definite click is heard when proper position is reached. Ice maker arm will remain in that position until pushed down.

Ice Service Rack (some models)

Install ice service rack by placing ice service rack on washers and sliding down.

A B

A Washer C Ice service rack B Screws

CAUTION

Make sure shelf is secure before placing items on shelf to avoid property damage.

Slideout Shelf (some models)

Slide out shelf pulls forward for easy access to items in back.

• Remove slideout shelf by sliding forward until ball point beneath center rail catches in molding groove.

• Grasp shelf by center rail, pull up, and remove.

• Slide in until ball point falls into molding groove.

A Central rail B Ball

Vertical Shelf Divider (some models)

Install vertical shelf divider by completing the following steps:

1. Slide prongs of shelf divider beneath desired grille

work, slightly off-center from center rail.

2. Press top of divider down and slide hook assembly

beneath center rail.

Pivot Bin

Pivot Bin™ provides convenient storage for frozen food items in Deepfreeze access of those items.

A Pivot Bin™

™

door and tilts forward for easy

Care and Cleaning

WARNING

To avoid electrical shock which can cause severe personal injury or death, disconnect power to refrigerator before cleaning. After cleaning, connect power.

CAUTION

To avoid personal injury or property damage, read and follow all cleaning product manufacturer's directions.

Textured Doors and Exterior

1. Wash surfaces with 4 tablespoons baking soda dissolved in 1 quart warm water and a soft, clean cloth.

2. Rinse surfaces with warm water. Dry surfaces with a soft, clean cloth.

• Do not use the following items:

- abrasive or harsh cleaners, ammonia, chlorine bleach, etc.

- concentrated detergents or solvents

- metal scouring pads

These items can scratch, crack and discolor surfaces.

• Do not place buckets, shelves, etc. in dishwasher.

Stainless Steel Cleaning

Damage to stainless steel finish due to improper use of cleaning products, or using non-recommended cleaning products, is not covered under warranty. For

Amana recommended products, call our Consumer Affairs division at 1(800) 843-0304, or contact us on the web at www.amana.com.

1. Wash surfaces with warm soapy water and a soft, clean cloth or sponge.

2. Rinse surfaces with warm water. Dry surfaces with a soft, clean cloth.

• Do not use the following harsh cleaners:

- abrasive or acidic cleaners(ammonia, chlorine bleach, vinegar-based product, etc.

- citrus-based cleaners

- scouring pads(metal, textured plastic, etc.)

These items can scratch, discolor, or permanently tarnish surfaces.

3. Follow up rinsing by immediately drying with a soft, clean cloth. This will avoid water spotting on

stainless steel finish.

Odor Removal

1. Remove all food.

2. Clean all interior surfaces including ceiling, floor, and walls according to attention to corners, crevices, and grooves. Include all drawers, shelves, and gaskets.

3. Wash and dry all bottles, containers and jars before returning food to refrigerator. Wrap foods in tightly sealed containers to prevent further odor. After 24 hours, check if odor was eliminated.

Complete the following steps if odor was not eliminated.

4. Complete steps 1–2.

5. Place garden fresh crispers on top shelf of Fresh Food section. Pack Fresh Food and Deepfreeze sections, including doors, with crumpled sheets of black and white newspaper.

General

instructions. Pay special

6. Place charcoal briquettes randomly throughout newspaper.

7. Close doors and let stand 24–48 hours.

8. Remove charcoal briquettes and newspapers.

9. Complete steps 2–3.

Contact Consumer Affairs Department if odor was still not eliminated.

Adhesives

1. Remove glue residue by rubbing toothpaste into adhesive with fingers until adhesive loosens.

2. Rinse surface with warm water. Dry surface with a soft, clean cloth.

CAUTION

To avoid personal injury or property damage, observe the following:

• Allow light bulb to cool.

• Wear gloves when replacing light bulb.

• Remove light bulb cover by removing ¼" hex nut

screws. Replace with appliance bulb no greater than 60 watts.

• Replace light bulb cover by replacing ¼" hex nut screws.

Door Gaskets

1. Clean door gaskets as necessary according to

General

and pliable to assure proper seal.

2. Apply a light film of petroleum jelly on hinge side of gasket to keep gaskets pliable.

instructions. Gaskets must be kept clean

Condenser Coils

Clean condenser coil every 3 months to ensure maximum performance of refrigerator. Accumulated dust and lint may cause the following:

• reduced cooling performance

• increased energy usage

• premature part failure

1. Remove toe grille by holding ends and pulling forward.

2. Clean front surface of condenser coil with a vacuum cleaner hose nozzle.

3. Replace toe grille by inserting clips in holes and snapping in.

Glass Shelves

CAUTION

To avoid personal injury or property damage, handle tempered glass shelves carefully. Shelves may break suddenly if nicked, scratched, or exposed to sudden temperature change.

Remove shelf by lifting front, releasing hooks from metal track then pulling out. Place shelf on a towel. Allow shelf to adjust to room temperature before cleaning.

Clean crevices by completing the following steps:

1. Dilute mild detergent and brush solution into crevices using a plastic bristle brush. Let set for 5 minutes.

2. Spray warm water into crevices using faucet spray attachment.

3. Dry shelf thoroughly and replace shelf by inserting hooks into metal track and lowering front.

Light Bulbs

WARNING

To avoid electrical shock which can cause severe personal injury or death, disconnect power to refrigerator before replacing light bulb. After replacing

light bulb, connect power.

A ¼" hex nut screws B Light bulb cover

Energy Tips

This refrigerator is designed to be one of the most energy efficient refrigerators available. Reduce energy use by observing the following.

• Operate in normal household temperatures of 55° to 110°F (13°C to 43°C) away from heat sources and direct sunlight.

• Set Fresh Food, Deepfreeze no colder than necessary.

• Keep Deepfreeze

• Keep door gaskets clean and pliable. Replace

gaskets if worn.

• Keep condenser coils clean.

section full.

, and drawer controls

Vacation Tips

Complete the following steps for short vacations.

1. Remove perishable foods. Warranty does not cover food loss. Check warranty certificate for specific coverage.

2. If an ice maker is installed, move ice maker arm to off position.

Complete the following steps for long vacations.

1. Empty Fresh Food and Deepfreeze

2. Unplug refrigerator.

3. Clean refrigerator and door gaskets according to

General

4. Prop doors open, so air can circulate inside.

5. If an ice maker is installed, turn water supply to refrigerator off and move ice maker arm to off position.

instructions in

Care and Cleaning

sections.

section.

Normal Operating Sounds

This new refrigerator may be replacing a differently designed, less efficient or smaller refrigerator. Today’s refrigerators have new features and are more energy efficient. As a result, certain sounds may be unfamiliar. These sounds are normal and will soon become familiar. These sounds also indicate refrigerator is operating and performing as designed.

1. Deepfreeze

compressor.

2. Deepfreeze® fan air rushes and whirs.

3. Sealed system (evaporator and heat exchanger)

refrigerant flow gurgles, pops or sounds like boiling water.

4. Defrost heater sizzles, hisses or pops.

5. Condenser fan air rushes and whirs.

6. Compressor has a high pitched hum or pulsating

sound.

7. Ice cubes from ice maker (some models) drop into

ice bucket.

8. Ice maker water valve hookup (some models)

buzzes when ice maker fills with water. This occurs whether or not refrigerator is connected to water supply. If refrigerator is not connected to water supply, stop sound by raising ice maker arm to off position.

Note: Foam insulation is very energy efficient and has excellent insulating capabilities. However, foam insulation is not as sound absorbent as previously used fiberglass insulation.

control clicks when starting or stopping

Before Calling For Service

Problem Solution

Refrigerator does not operate.

Refrigerator still won’t operate.

Food temperature appears too warm.

Temperature controlled drawer temperature is too warm. Food temperature is too cold.

Refrigerator runs too frequently.

Water droplets form on inside of refrigerator.

Water droplets form on outside of refrigerator. Drawers do not close freely. • Check for a package which may prevent drawer from closing properly.

Refrigerator has an odor. • See Odor Removal instructions in Care and Cleaning section. Refrigerator or ice maker

(some models) make unfamiliar sounds or seems too loud.

• Confirm Deepfreeze® control is on.

• Confirm refrigerator is plugged in.

• Check fuse or circuit breaker. Plug in another item at that wall outlet.

• Wait 40 minutes to see if refrigerator restarts. If Deepfreeze

control is on, lights work but 2 fans and compressor are not operating, refrigerator may be in defrost cycle.

• Unplug refrigerator. Transfer food to another unit or place dry ice in Deepfreeze

section to preserve food.

Warranty does not cover food loss.

Check warranty certificate for specific coverage.

1-800-628-5782

• Call

inside U.S.A. and

1-319-622-5511

outside U.S.A. to locate

an authorized Amana technician.

• See above sections.

• Allow time for recently added warm food to reach Fresh Food or Deepfreeze

temperature.

• Check gaskets for proper seal.

• Clean condenser coils.

• Adjust Fresh Food and/or Deepfreeze

control.

• Slide control to colder setting.

• Adjust Deepfreeze

control to colder setting.

• Clean condenser coils.

• Adjust Fresh Food control.

• Adjust Deepfreeze

control to warmer setting. Allow several hours for

temperature to adjust.

• It may be normal to maintain constant temperature.

• Doors may have been opened frequently or for an extended period of time.

• Allow time for recently added warm food to reach Fresh Food or Deepfreeze

temperature.

• Clean condenser coils.

• Adjust Deepfreeze

control.

• Check gaskets for proper seal.

• It is normal during high humidity periods or if doors have been opened

frequently.

• Check door gaskets for proper seal.

• Confirm drawer is in proper position.

• Clean drawer channels with warm, soapy water. Rinse and dry thoroughly.

• Apply a thin layer of petroleum jelly to drawer channels.

• Confirm refrigerator is level.

• It may be normal. See Normal Operating Sounds section.

Problem Solution

Ice maker (some models) is not producing ice.

• Confirm ice maker arm is down.

• Confirm household water supply is reaching water valve.

• Confirm ice maker wiring harness is completely inserted into proper holes.

• Check for kinks in copper or plastic tubing. Remove kinks or replace tubing.

• Check electrical connections to water valve coil and connector block on

refrigerator cabinet.

• Confirm Deepfreeze

section is operating at proper temperature.

Ice cubes have an odor. • See Odor Removal instructions in Care and Cleaning section.

• Discard ice and clean ice bucket or trays more frequently. Ice cubes are porous and absorb odors easily.

Ice cubes stick together or ‘shrink’.

Ice forms in inlet tube to ice maker (some models).

• Empty ice cube bucket or trays more frequently. If used infrequently, ice cubes may stick together or shrink.

• Check water pressure. Low water pressure will cause valve to leak. Selfpiercing valves cause low water pressure.

Amana recommends using a saddle valve. Contact 1-800-843-0304 or an Amana dealer for availability. Do not use self-piercing valve. Amana is not responsible for property damage due to improper installation or water connection.

+ 42 hidden pages