Amana AMC2206BAW15, AMC2206BAW06, AMC2206BAW00, AMC2206BAS15, AMC2206BAS06 Installation Guide
...
MICROWAVE OVEN BUILT-INTRIM KIT
INSTALLATIONINSTRUCTIONS
Built-In Trim Kit Models UMTK27, UMTK30
UL listed for use over built-in electric ovens:
27 (68.6 cm): MEW5527, MEW6527
30 (76.2 cm): MEW5530, MEW6530, JJW8130DD, JJW8330DD, JJW9130DD, JJW9330DD
Tableof Contents
MICROWAVEOVENSAFETY...........................................................1
INSTALLATIONINSTRUCTIONS.....................................................2
Toolsand Parts...............................................................................2
Location Requirements...................................................................2
Minimum Cutout Dimensions.........................................................2
Trim KitFrame Dimensions............................................................2
ElectricalRequirements..................................................................3
Microwave Oven Preparation.........................................................3
DuctAssembly................................................................................3
Microwave Oven Installation...........................................................4
InstallTop and Bottom Brackets....................................................4
InstallTrim Kit Frame......................................................................4
MICROWAVE OVEN SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
W10308503A
INSTALLATIONINSTRUCTIONS
t'O0_S 3_J
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
• Measuring tape • Drill
• Pencil • 7/64" drill bit
• Phillips screwdriver • Tape
Parts Supplied
(7.6
(42.9
3"
11/16Jt
(1.8cm)
B
Duct base Trimkit frame
Left duct Templates1 and 2
Bottom bracket Topbracket
13/16" screws (2) 9/16" screws (16) 1/2" screws (4- painted)
The microwave oven may be installed over a built-in oven. If
installing over a built-in oven, make sure there is a minimum of 3"
(7.6 cm) between the top of the lower oven cutout and the
microwave oven cutout floor.
The microwave oven may also be installed in a cabinet by itself
(without a built-in oven below). For best usability, we recommend a
minimum distance of 36" (91.4 cm) from the floor to the cutout floor.
Make sure the surrounding cabinetry has clearance to open and
close freely. Allow a clearance of at least 1" (2.5 cm) below the
cutout floor (3" [7.6 cm] for installation above a built-in oven), and
a clearance of at least 2" (5.1 cm) above the cutout opening.
I
A. Trim kit frame overhang
B. Cutout for lower oven
NOTES:
• Height, width and depth measurements have _+1/16" (2 mm)
tolerance.
• 3" (7.6 cm) minimum dimension is from lower oven cutout
ceiling to microwave oven cutout floor.
• Trim kit frame extends 11/16" (1.8 cm) below, and 19/16''
(4.0 cm) above the cutout opening.
_ ,_ _, i _ _ _ _ , _ _,,_,_ _ ,-_
26_,,
t
19_/8,,
(48.6 crn)
!
*27" (68.6 cm) trim kit
**30" (76.2 cm) trim kit
24" (61.0 c_)
17/W' (3.7 crn)*
27/8" (7.3 crn)**
(2.2 crn)
3" (7.6 crn)
1"
(2.5cm) f
2
3"
-(7.6 crn)
36"
(91.4 c
t
A. Upper cabinet D. Lower cabinets
B. Microwave oven cutout E.Floor
C. Lower oven cutout
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Observe all governing codes and ordinances.
Required:
• A 120 Volt, 60 Hz, AC only, 15- or 20-amp electrical supply
with a fuse or circuit breaker.
Recommended:
• A time-delay fuse or time-delay circuit breaker.
• A separate circuit serving only this microwave oven.
' J,_CS _/_ __,#
1,
Unplug microwave oven before proceeding with installation.
2.
Remove any loose items inside microwave oven.
1. Remove 4 existing screws (2 on each side) from the
microwave oven. The screws are located at the lower edge.
These screws will be used in the next step.
2. Secure duct base to the microwave oven with the 4 existing
screws removed in Step 2.
o@
1
A. Duct base
B.Existingscrews (4)
3,
Secure left duct to outside panel of microwave oven with one
9/16" screw, as shown.
GROUNDING iNSTRUCTiONS
[] For all cord connected appliances:
The microwave oven must be grounded. In the event of
an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current. The microwave oven is equipped with a cord
having a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly installed
and grounded.
WARNING: Improper use of the grounding plug can
result in a risk of electric shock. Consult a qualified
electrician or serviceman if the grounding instructions are
not completely understood, or if doubt exists as to whether
the microwave oven is properly grounded.
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician or serviceman install
an outlet near the microwave oven.
SAVE THESE iNSTRUCTiONS
A. Left duct
B. 9/16" screw
1,
On the cutout floor, find and mark the centerline.
2.
Use Template 1 to mark hole center for box screw. Be sure to
align the center line of template to center line of cutout floor.
J
.f ....
,{
- "_.(37.5 crn) ...._
j_
A
B
A. Cutout floor
B. Center line
C. Cutout opening
3,
Using 7/64" drill, drill pilot hole into hole center marked in
Step 2.
Loading...