Amana Product Information by Fax / Internet
800-843-0304 / http://www.amana.com
Amana Electric Downdraft Cooktops: Fax Document Number: 3044 / 010701
Models AKED3050
General
Recessed Porcelain Surface AKED3050E / AKED3050WW
Recessed Stainless Steel Surface AKED3050SS
“On” Indicator Light Yes
Infinite Setting Controls Yes
Variable Downdraft Vent System Yes
Downdraft has 402 Maximum CFM at 0 ft. Yes
Optional Cartridges*
Exclusive Smoke Control Grill,
2000W Excalibur Non Stick Coating.
Exclusive Smoke Control Griddle
(Must purchase ACL100 grill cartridge to use griddle)
Electric Coil (6” / 8”) 1,500W / 2,100W
Radiant (6 1/2” / 8 1/2”) 1,200W / 2,000W
Quartz Halogen (6 1/2” / 8 1/2”) 1,200W / 2,000W ACH100E/WW
Optional Wall Cap CC30
Colors
Black-On-Black AKED3050E
White-On-White AKED3050WW
Stainless Steel AKED3050SS
Electrical
Electrical Requirements
Warranty
Cooktops
Cartridges
Overall Dimensions (in Inches)
Width 29 1/2
Depth 21 1/2
Cutout Dimensions (in Inches)
Width 28 7/8
Depth 20 5/8
Clearance to Top of Countertop 7 3/4
Approximate Shipping Weight (lbs.) 58
*Unit Does Not Come with Any Cartridges
ACR110E/WW/SS - Large Element in Front
(Right Side Installation Only)
ACR100E/WW - Large Element in Rear:
(Installs on Either Side)
ACT110E/WW or ACT111E/WW
Large Element in Front:
(Right Side Installation Only)
ACT100E/WW or ACT101E/WW
Large Element in Rear:
(Installs on Either Side)
120/240 VAC, 60HZ, 7.3 KW, 4 Wire, 30 Amp Max
120/208 VAC, 60HZ, 5.5 KW, 4 Wire, 30 Amp Max
Warranty applies only when product is
repaired by an authorized Amana servicer.
Full 1 year - parts, labor and travel
Limited 5 years on electric surface elements – parts
Limited 1 year - parts only
Limited 5 years on electric heating elements and/or
glass ceramic top - parts only
ACL100
ACG100
only
Amana’s ongoing commitment to quality products may mean a change in product specifications without notice.
Doc. 3044, Page 1 of 4
Amana Product Information by Fax / Internet
inch thick
cooktop.
800-843-0304 / http://www.amana.com
Cutout Dimensions for Countertop Installation
1
4
min
/2"
3 1/2"
min
20
5/
"
8
2 1/2"
28
7/
"
8
Wall oven
cutout
3 1/2"
min
Minimum Clearances to Combustible Surfaces
The dimensions provided are to be
measured from the cooktop itself, and not
the installation cutout for the cooktop.
A—30 inches minimum clearance between
the top of the cooking surface and the
bottom of an unprotected wood or metal
cabinet.
OR
A—24 inches minimum clearance when
bottom of wood or metal cabinet is
protected by not less than 1/4-inch thick
flame retardant millboard covered with not
less than No.28 MSG sheet steel, 0.015
inch thick stainless steel, 0.024-
aluminum, or 0.020 inch thick copper.
B—3 inches minimum distance between
cooktop and wall, cabinet taller than 36
inches or a walkway.
C—1 1/2 inches minimum distance between
cooktop and bac k wall or backguard.
D—2 inches minimum distance between
cooktop and edge of countertop.
E—Minimum of 18 inches (on each side)
between top of countertop and bottom of
an unprotected wood or metal cabinet.
F—Minimum of 30 inches (30-inch cooktop)
length for protected cabinets above the
D
2 "
min
C
29 1/2"
8 3/16"
21 1/2 "
F
A
E
B
Amana’s ongoing commitment to quality products may mean a change in product specifications without notice.
Doc. 3044, Page 2 of 4
Amana Product Information by Fax / Internet
4"
4"
Duct Locations without a Wall Oven
Duct Length Calculations
800-843-0304 / http://www.amana.com
Cooktop Side View Cooktop Front View
7 7/8"
Front
6 7/8"
Cooktop can be vented vertically or horizontally.
- If vented horizontally vent air through left or rear wall.
- If vented vertically, locate hole between joists.
- Do not vent exhaust air into a wall, ceiling, or a
concealed space of a building.
7 7/8"
6"
C
L
2 1/16"
8 1/4"
3 3/8"
C
L
6 1/2"
- Vent cutout should be 3 1/2” x 10 1/2” or a 7” round
1
opening.
12
/2"
Ducting length is calculated in terms of straight metal
duct. Fittings such as elbows or transition pieces
should be limited to 50% of total duct length. Using
too many fittings can cause airflow problems.
Maximum allowable calculated duct length is 60
equivalent feet.
- Use Duct Length Piece Equivalents section found
in the Installation Instructions .
- Do not use any duct other than metal.
- Flexible duct is not recommended because it can
create a fire hazard. However, if it is used, one
foot of flexible duct is equal to two feet of smooth
metal duct.
- Exterior exhaust opening must be a minimum of
one foot (12 inches) from an obstruction.
Back Edge of
Cooktop Cutout
5'
1'
1' of Duct 1'
90° Elbow 5'
3'
5'
10'
1'
3' of Duct 3'
90° Elbow 5'
10' of Duct 10'
Total Feet 24'
Amana’s ongoing commitment to quality products may mean a change in product specifications without notice.
Doc. 3044, Page 3 of 4
Amana Product Information by Fax / Internet
Duct Locations Above a Wall Oven
800-843-0304 / http://www.amana.com
Cooktop can be vented vertically or horizontally.
- If vented horizontally, vent air through left or
rear wall.
- If vented vertically, vent edge must be a
minimum of 3/4-inch away from the wall oven.
- Do not vent exhaust air into a wall, ceiling, or a
concealed space of a building.
- Duct cutout size should be 3 1/2” x 10 1/2”.
4 1/2"
C
27 1/4"
L
2 1/16"
28 1/2"
6"
3 3/8"
C
L
3
/4"
C
L
3 3/8"
C
L
C
L
3
2 1/16"
/4 "
min
Amana’s ongoing commitment to quality products may mean a change in product specifications without notice.
Doc. 3044, Page 4 of 4
Loading...