Amana ACR4503SEW, ACR4303MES User Manual

30" (76.2 cm) Freestanding Electric Range

PRODUCT MODEL NUMBERS

ACR3130BA
ACR4303ME
ACR4530BA
ACR4503SE

Electrical: To properly install your range, you must determine the type
of electrical connection you will be using and follow the instructions
provided for it here.

• Range must be connected to the proper electrical voltage and
frequency as specied on the model/serial number rating plate. The
model/serial number rating plate is located on the left side frame
behind the storage drawer panel or behind the top right side of the
oven door. Refer to the gures in the “Product Dimensions” section

of the “Location Requirements” section.

• This range is manufactured with the neutral terminal connected to
the cabinet. Use a 3-wire, UL listed, 40- or 50-amp power supply
cord (pigtail) (see following Range Rating chart). If local codes do
not permit ground through the neutral, use a 4-wire power supply
cord rated at 250 volts, 40 or 50 amps and investigated for use

with ranges.

Range Rating*

120/240 Volts 120/208 Volts Amps

8.8 – 16.5 KW 7.8 – 12.5 KW 40 or 50 **

16.6 – 22.5 KW 12.6 – 18.5 KW 50

* The NEC calculated load is less than the total connected load listed

on the model/serial rating plate.

** If connecting to a 50-amp circuit, use a 50-amp rated cord with kit.

For 50-amp rated cord kits, use kits that specify use with a nominal

3

1

/8" (34.9 mm) diameter connection opening.

• A circuit breaker is recommended.

AER3311WA
AER5330BA
AER5523XA
AER5524XA

AER5630BA
AER5823XA
AER5830VA

Specied Rating of
Power Supply Cord Kit
and Circuit Protection

CABINET OPENING DIMENSIONS

Cabinet opening dimensions shown are for 25" (64.0 cm)
countertop depth, 24" (61.0 cm) base cabinet depth and 36"
(91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood
combination above the range, following the range hood or microwave
hoods combination instructions for dimensional clearances
above the cooktop surface.

A freestanding range may be installed next to combustible walls
with zero clearance.

* NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet

is covered by not less than 1/4" (0.64 cm) ame retardant millboard
covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm)
stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the cooking
platform and the bottom of an uncovered wood or metal cabinet.

Because Whirlpool Corporation includes a continues commitment to improve
our products, we reserve the right to change materials and specications
without notice.

PRODUCT DIMENSIONS

A

F

E

D

A. 273/4" (70.5 cm) max. depth with handle
B. 467/8" (119.1 cm) overall height (max.) with leveling legs

screwed all the way in*

C. 36" (91.4 cm) cooktop height (max.) with leveling legs

screwed all the way in*
D. 297/8" (75.9 cm) width
E. 255/16" (64.3 cm) depth – back of range to front of cooktop**
F. Model/serial rating plate (located on the left side frame behind

storage drawer or right side of frame behind the oven door)

IMPORTANT: Range must be level after installation. Follow
the instructions in the “Level Range” section. Using the cooktop
as a reference for leveling the range is not recommended.

* Range can be raised approximately 1" (2.5 cm)

by adjusting the leveling legs.

** Front of door and drawer may extend further forward

depending on styling.

A

B

D

E

A. 13" (33.0 cm) max. upper cabinet depth
B. 30" (76.2 cm) min. opening width
C. For minimum clearance to top of cooktop, see NOTE*.
D. 301/8" (76.5 cm) min opening width
E. Outlet – 8" (20.3 cm) to 22" (55.9 cm) from either cabinet,
51/2" (14.0 cm) max. to oor

F. Cabinet door or hinges should not extend into the cutout

Dimensions are for planning purposes only. For complete details,
see Installation Instructions packed with product. Specications
subject to change without notice.

C

F

B

C

Ref. W10403811C

8/3/15