Altronix ALTV1224DCCB220, ALTV1224DC1CB220, ALTV1224DC2CB220, ALTV1224DCCB, ALTV1224DC1 Installation Manual

ALTV1224DC220 Series

CCTV Power Supplies

Installation Guide

Models Include:

• ALTV1224DC220 • ALTV1224DCCB220

- 12VDC or 24VDC @ 4A. - 12VDC or 24VDC @ 4A.

- Eight (8) Fuse Protected Outputs. - Eight (8) PTC Protected Outputs.

• ALTV1224DC1220 • ALTV1224DC1CB220

- 12VDC or 24VDC @ 4A. - 12VDC or 24VDC @ 4A.

- Sixteen (16) Fuse Protected Outputs. - Sixteen (16) PTC Protected Outputs.

• ALTV1224DC2220 • ALTV1224DC2CB220

- 12VDC or 24VDC @ 6A. - 12VDC or 24VDC @ 6A.

- Sixteen (16) Fuse Protected Outputs. - Sixteen (16) PTC Protected Outputs.

Rev. 022505

Overview:

D1

INPUT

R1

LED

Used on PTC Models

(example: ALTV1224DCCB220)

220VAC

power
mains

Divider

ALTV1224DC220 Series DC CCTV power supplies are designed to power CCTV Cameras and accessories. Units provide
12VDC or 24VDC distributed via eight (8) or sixteen (16) fused or PTC protected outputs with a total of 4A or 6A total
continuous supply current.

Eight (8) or Sixteen (16) Output ALTV1224DC Reference Chart:

Altronix
Model Number

ALTV1224DC220
ALTV1224DCCB220
ALTV1224DC1220
ALTV1224DC1CB220
ALTV1224DC2220
ALTV1224DC2CB220

Output

Voltage

12VDC

or

24VDC

Total

Output
Current
(Power)

4A

6A 16

Number

of

Outputs

8

16

PTC

Protected

Outputs

-----

P

-----

P

-----

P

Fuse

Protected

Outputs

P

----- 2.5A

P

----- 2.5A

P

----- 2.5A

Output

Current

(max per

output)

3.5A

3.5A

3.5A

220VAC

50/60Hz

Input

Current

0.9A

1.5A

Input:

• Input 220VAC (working range 198VAC-256VAC),
50/60 Hz.

Output:

• Eight (8) or sixteen (16) fuse or PTC protected outputs.

• 12VDC or 24VDC.

• Outputs are rated @ 3.5A (fused) or 2.5A (PTC).

• Filtered and electronically regulated outputs.

Specifications:

Features:

• AC input and DC output LED indicators.

• Power ON/OFF switch.

• Unit maintains camera synchronization.

• Ease of installation saves time and eliminates
costly labor.

Enclosure Dimensions (H x W x D approx.):

13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm).

Installation Instructions:

1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install two fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 6).
Secure enclosure to earth ground.

2. Slide switch to OFF position (Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5).

3. Set the unit to desired DC output voltage range by setting switch (SW1) on the power supply board to the appropriate
position. Use trimpot to adjust voltage if necessary (Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5).

4. Connect AC circuit (220VAC, 50/60Hz) as follows: Green branch wire connects to earth (safety) ground lug .
Line and Neutral to the connector on power supply board marked [L, N] respectively
(Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5).

5. Measure output voltage before connecting devices. This helps avoiding potential damage.

6. Connect each DC device to the output terminals 1 through 8 (Fig. 1, pg. 3) or terminals 1 through 16
(Fig. 2, pg. 4 or Fig. 3, pg. 5).
Note: Be careful to observe camera polarity.

7. When batteries are being used, the DC output voltage must be adjusted by turning the trim pot VR1
(Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5) clockwise to increase the output voltage to 13.7VDC for 12VDC
operation and 27.1VDC for 24VDC operation.
Connect battery to theterminals marked [-- BAT + ] (battery leads included) (Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5).
Use two (2) 12VDC batteries connected in series for 24VDC operation.

8. Slide switch to ON position (Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5).

9. Green LED on the PD8/PD8CB or PD16W/PD16WCB board will illuminate when power is present.

10. Upon completion of the wiring, secure enclosure door with screws (supplied).

WARNING: To reduce the risk of fire or electric shock do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to the National
Electrical Code and all local codes.

- 2 - ALTV1224DC220 Series

ALTV1224DC/CB Terminal Identification:

CAUTION: De-energize unit prior to servicing. For continued protection against

OLS127220 - Power Supply

Terminal Legend Function/Description

L, N 220VAC power mains connection.
– DC + 12VDC or 24VDC @ 4A total continuous output.
– BAT + Stand-by battery connections. Maximum charge rate 0.5A.

PD8/PD8CB - Power Distribution Module

Terminal Legend Function/Description

1P - 8P Positive DC power outputs.
1N - 8N Negative DC power outputs.

Fig. 1

fire hazard replace fuse with the same type and rating. Do not expose unit to rain or moisture.

Divider

LED

Door

Wire Strap

(from

Enclosure

to Door)

Ground

Lug

220VAC

power
mains

OFF - 24V

ON - 12V

1 2 3 4 5 6 7 8

OFF ON

ON

ON

OFF - 24V
ON - 12V

Switch disables power mains
line voltage input.

If stand-by battery (batteries) are
connected the DC output remains on.

SW1
24VDC output - OFF
12VDC output - ON

INPUT

D1

R1

FUSED POWER OUTPUTS

COMMON POWER OUTPUTS

N

P

Used on PTC Models

(example: ALTV1224DCCB220)

Trimpot
Adjusts output voltage
on power supply

ALTV1224DC220 Series - 3 -

ALTV1224DC1/CB Terminal Identification:

OLS127220 - Power Supply

Terminal Legend Function/Description

L, N 220VAC power mains connection.
– DC + 12VDC or 24VDC @ 4A total continuous output.
– BAT + Stand-by battery connections. Maximum charge rate 0.5A.

PD16W/PD16WCB - Power Distribution Module

Terminal Legend Function/Description

1P - 16P Positive DC power outputs.
1N - 16N Negative DC power outputs.

Fig. 2

CAUTION: De-energize unit prior to servicing. For continued protection against
fire hazard replace fuse with the same type and rating. Do not expose unit to rain or moisture.

Door

Wire Strap

(from

Enclosure

to Door)

Ground

Lug

220VAC

power
mains

ON - 12V

OFF - 24V

ON

Divider

12345678

OFF ON

ON

OFF - 24V
ON - 12V

9 10 11 12 13 14 15 16

common

outputs
protected

outputs

For continuous protection against risk of fire

replace fuses with same type and rating.

3.5A 250V

Switch disables power mains
line voltage input.

If stand-by battery (batteries) are
connected the DC output remains on.

SW1
24VDC output - OFF
12VDC output - ON

Trimpot
Adjusts output voltage
on power supply

N

P

NP

NPS

XFMR Input

Used on PTC Models

(example: ALTV1224DC1CB220)

12345678

common

outputs

protected

outputs

9 10 11 12 13 14 15 16

N

P

NP

NPS

XFMR Input

- 4 - ALTV1224DC220 Series

ALTV1224DC2/CB Terminal Identification:

OLS187220 - Power Supply

Terminal Legend Function/Description

L, N 220VAC power mains connection.
– DC + 12VDC or 24VDC @ 6A total continuous output.
– BAT + Stand-by battery connections. Maximum charge rate 0.5A.

PD16W/PD16WCB - Power Distribution Module

Terminal Legend Function/Description

1P - 16P Positive DC power outputs.
1N - 16N Negative DC power outputs.

Fig. 3

CAUTION: De-energize unit prior to servicing. For continued protection against
fire hazard replace fuse with the same type and rating. Do not expose unit to rain or moisture.

Door

Wire Strap

Enclosure

to Door)

(from

Ground

Lug

OFF - 24V

ON - 12V

Divider

12345678

3.5A 250V

ON

OFF ON

ON

OFF - 24V
ON - 12V

Switch disables power mains
line voltage input.

If stand-by battery (batteries) are
connected the DC output remains on.

SW1
24VDC output - OFF
12VDC output - ON

Trimpot
Adjusts output voltage
on power supply

9 10 11 12 13 14 15 16

common

outputs

protected

outputs

For continuous protection against risk of fire

replace fuses with same type and rating.

N

P

NP

NPS

XFMR Input

ON OFF

5A 250V

LGN

220VAC

power
mains

AC

DC

--- BAT + --- DC +

Used on PTC Models

(example: ALTV1224DC2CB220)

12345678

common

outputs

protected

outputs

9 10 11 12 13 14 15 16

N

P

NP

NPS

XFMR Input

ALTV1224DC220 Series - 5 -

The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the

(

)

(

)

(

)

presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of sufficient
magnitude to constitute an electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION: To reduce the risk of electric shock do not open enclosure. There are
no user serviceable parts inside. Refer servicing to qualified service personnel.

Enclosure Dimensions:

13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)

1.40”

(36mm)

1.20”

(31mm)

(36mm)

0.75”

(19mm)

1.40”

4.85”

(123mm)

12.5”

(318mm)

11.0”

(279mm)

4.85”

(123mm)

1.40”

(36mm)

(19mm)

0.75”

1.20”

(31mm)

0.9375”
(24mm)

3.25”

(83mm)

1.20”

(31mm)

1.40”

(36mm)

5.10”

(130mm)

5.10”

(130mm)

3.25”

(83mm)

13.0”

(330mm)

1.0”

(25mm)

0.9375”
(24mm)

1.0”

(25mm)

3.25”

(83mm)

3.25”

(83mm)

5.10”

(130mm)

6.5625”

(167mm)

1.0”

25mm

10.5”

267mm

1.0”

25mm

- 6 - ALTV1224DC220 Series

Notes:

ALTV1224DC220 Series - 7 -

Notes:

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: [phone]
web site: www.altronix.com, e-mail: [e-mail]. Lifetime Warranty, Made in U.S.A.

- 8 - ALTV1224DC220 Series

IIALTV1224DC220Series A12P

MEMBER