Page 1
ALTV1224C4
Door
Wire Strap
(from
Enclosure
to Door)
Black
L
ead
White
Lead
XFMR XFMR
+ DC1 --- + DC2 ---
AC
XFMR IN
AC1 AC2
DC
ON OFF
SW1
F1
F2 F3 F4
ON OFF
SW2
Voltage
Adjustment
Inp
ut
115VA
C
60Hz,
2 a
mp
AC/DC Dual Output Power Supply
Overview:
The Altronix ALTV1224C4 AC/DC Dual Output Power Supply is designed to provide both 12VDC and 24VAC outputs
where a combination of both AC and DC outputs are required. Provides two (2) 12VDC outputs with a total current of 2
amp and two (2) 24VAC outputs with a total current of 4 amp.
Specifications:
• 115VAC 50/60 Hz, 2 amps.
• Four (4) individually fuse protected outputs:
- Two (2) outputs @ 12VDC
- Two (2) outputs @ 24VAC.
• 2 amp supply current at 12VDC
• 4 amp supply current at 24VAC
• Output fuses are rated at:
AC fuses: 3.5 amp / 250VAC.
DC fuses: 1 amp / 250V
• AC/DC power LED indicators.
• Power ON/OFF switch.
• Spare fuses included.
• Unit maintains camera synchronization.
• Ease of installation sa
ves time and
eliminates costly labor.
Enclosure dimensions: 13.5"H x 13"W x 3.25"D
.
(Fig. 1).
(Fig. 1).
AC.
Installation Instructions:
1. Mount unit in desired location. Mark and
predrill holes in the wall to line up with the
o keyholes in the enclosure. Install
top tw
two upper fasteners and screws in the wall
with the screw heads protruding. Place the
enclosure’
s upper k
upper screws, le
position of the lo
eyholes o
vel and secure. Mark the
wer two holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the
ver the two
enclosure’s upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws
(Enclosure Dimensions, pg. 2). Secure enclosure to earth ground.
2. Slide switches SW1, SW2 to OFF position.
3. Connect the AC (115VAC 50/60 Hz) to the two black and white flying leads of the transformers.
4. Measure output voltage before connecting devices.
5. Connect devices to output terminals using the following procedure.
Connect DC cameras to terminals marked [+ DC1 -- , + DC2 -- ] carefully observing the correct polarity.
C cameras to ter
Connect
6. Slide switches SW1, SW2 to ON position.
7. Green LED on the circuit board will illuminate when power is present.
Upon completion of wiring, secure enclosure door with scre
8.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. This instal-
A
lation should be made by qualified service personnel and should confor
AC2].
C1,
minals mark
ed [A
ws (supplied).
m to all local codes and in accordance
with the National Electrical Code.
Fuse Replacement:
Before replacing fuses slide s
1.
witchs SW1, SW2 to OFF position.
2. Replace AC outputs fuses F1 or F2 with fuses rated @ 3.5 amp/250VAC.
Replace DC outputs fuses F3 or F4 with fuses rated @ 1 amp/250VAC.
Fig. 1
Page 2
Terminal Identification:
5.10"
6.5625"
3.25"3.25"
5.10"
5.10"
3.25"
1.00"10.50"1.00"
1.00"
1.00"
1.40"
1.20"
1.40"
1
.20"
0.75
"0.75" 11.00"
12.50"
3.25"
0.9375"
0.9375"
1
.40" 4.85" 4.85" 1.40"
1
.20"
Bottom
Top
RightLeft
T
erminal Legend Function/Description
XFMR IN Low voltage AC input from two (2) (24VAC / 100VA).
+ DC1 -, + DC2 - DC power outputs.
AC1, AC2 AC power outputs.
Enclosure Dimensions:
13.5"H x 13"W x 3.25"D
Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.
ork 11220 USA, 718-567-8181, f
Y
w
140 58th Street, Brookl
web site: www.altronix.com, e-mail: info@altronix.com, Made in U.S.A.
IIALTV1224C4 - Rev. 062906 F29F
yn, Ne
ax: 718-567-9056
MEMBER
Loading...