Alpine TMX-R680A User Manual

®

PUSH

TMX-R680A

Mobile Overhead Monitor

OWNER’S MANUAL

It is dangerous and illegal for the driver to watch the TV/Video while

WARNING

!

Caution

• Read this manual thoroughly before starting installation and operation. You will find a number of Safety Warnings
in this manual to tell you about things that could hurt you or other people if you were to ignore the Warnings. We
cannot be responsible for problems resulting from failure to observe the Warnings in this manual.

• This manual uses a symbol to show how to use this product safely and to avoid harm to yourself and others and
damage to your property. Here is what this symbol means. Understanding it is important for reading the Manual.

• Meaning of Symbol:

!

DO NOT DISASSEMBLE OR ALTER

Attempts to disassemble or alter this product can lead to accidental fires or electrical shock.

KEEP SMALL ARTICLES OUT OF THE REACH OF CHILDREN

Keep small articles (wire-ties, etc.) out of reach of children. If swallowed, consult a physician immediately.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND

Use only in cars with a 12 volt negative (–) ground electrical system. (Check with your dealer if you are not sure.)
Failure to do so may result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL

Before doing any electrical wiring, disconnect the cable from the negative (–) terminal of the battery. Failure to do so
may result in electric shock or injury due to electrical shorts.

KEEP ELECTRICAL CABLES TOGETHER TO AVOID OPERATING HAZARDS

Dress the wiring to keep them from interfering with the operation of the steering wheel, gear lever, brake pedals, etc.

DO NOT CUT AWAY ANY WIRE INSULATION TO USE ITS POWER FOR OTHER EQUIPMENT

Tapping power from wiring to supply voltage to another piece of equipment could exceed the current carrying
capacity of that wire. This could result in fire or electric shock.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION

Do not install in locations which might create hazards for the vehicle occupants or hinder vehicle operation (such as
the steering wheel or gear shift) by obstructing forward vision or hampering movement etc.

DO NOT DAMAGE PIPES OR WIRING WHEN DRILLING HOLES

When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes,
tanks or electrical wiring. Failure to take such precautions may result in fire.

DO NOT USE NUTS OR BOLTS IN THE BRAKE SYSTEM FOR INSTALLATION OR GROUND
CONNECTIONS

Never use safety-related parts such as bolts or nuts in the steering or brake systems or tanks to make wiring
installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.

HALT USE IMMEDIATELY IF A PROBLEM APPEARS

When problems appear, stop using the system immediately and contact the dealer from whom you purchased the
equipment. Some problems which may warrant immediate attention include a lack of sound, noxious odors or smoke
being emitted from the unit, or foreign objects dropped inside the unit.

DO NOT OPERATE THE EQUIPMENT OR LOOK AT THE SCREEN WHILE DRIVING

Do not change settings while driving. If operation requiring a prolonged view of the display is required, stop the
vehicle in a safe location before attempting operation.

DO NOT INSTALL THE MONITOR NEAR THE PASSENGER SEAT AIR BAG

Ensure that the location chosen for the monitor does not interfere with the operation of the passenger seat air bag.
This will prevent the triggered air bag from launching the display towards passengers, possible causing injury.

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS

The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always
contact the dealer where you purchased this unit to have the work done.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST

Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this
unit may cause smoke or fire.

MAKE THE CORRECT CONNECTIONS

Failure to make the correct connections can cause fire or accident to occur.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED

Route the cables and wiring so as not to be crimped by moving parts like seat rails or to make contact with sharp
spots which could damage the wiring.

DO NOT RAISE THE VOLUME EXCESSIVELY

Keep the volume at a level where you can still hear outside noises while driving. Driving while unable to hear outside
sounds could cause an accident.

WARNING

driving the vehicle. The driver may be distracted from looking ahead
and an accident could occur.

This symbol means there is something that could cause serious injury or
death to you or other people.

FEATURES/DESCRIPTION

Alpine’s TMX-R680A integrates a 6.8 inch color LCD panel, infrared transmitter for wireless
headphones, dual video source selector, and remote controllable dome light. This gives the
passengers in the rear seats of your vehicle, the ability to enjoy many different A/V sources (such
as a VCR, DVD, TV Tuner and Video Game). The TMX-R680A combines all these features into a
single pod mounted to the vehicles head liner. Alpine’s SmartView™ swivel mechanism was
designed to give the rear seat passengers flexibility in adjusting the monitor for the best picture
possible from any angle.

It is dangerous and illegal for the driver to watch TV/Video while driving any

!

WARNING

Features:

Dual A/V Inputs

Including one, 5m, mini-DIN extension to connect either of the 2 inputs to an A/V source. The
Mini-DIN to RCA interface converts the DIN input to standard RCA-type. The two inputs are
selected using the wireless remote control.

Single A/V Output

An auxiliary A/V output is provided to you to send video and audio to an additional monitor.
This signal mirrors what’s being shown on the TMX-R680A display.

Dual Headphone Outputs (wired)

Two headphone output jacks help to reduce interference from other audio sources. Infrared,
wireless headphones can also be used thanks to the built-in IR transmitter array.

Dome Light (3-way Controllable)

The integrated dome light has its own DC source (yellow/green wire). This wire, along with one
of the control wires must be connected for the Dome light to operate properly. Operation can
also be controlled through the wireless remote control. A Delayed Dome Light function can also
be programmed, if desired.

Wireless Remote Control (w/Remote Output for external source)
IR Transmitter for wireless headphones
Wireless IR Headphone (SHS-N101) compatible
V ariable Audio Output
OSD (On-screen Display)

vehicle. The driver may be distracted from looking ahead and an accident
could occur.

Note:

If you have any questions regarding the application of this device, see your authorized Alpine
dealer.
It is recommended that this product be used with Alpine’s various Overhead Consoles. Your
authorized Alpine dealer will have more information on these products.

See page 14 for a typical Entertainment system using the TMX-R680A.

4

PUSH

OPERATION - Overhead Monitor

Headphone
Outputs (2)

SmartView Swivel

Mechanism

LCD Monitor

Panel

Monitor Open

Button

Dome Light

IR Sensor/Logo

Headphone Outputs

Two output jacks (mini-phono plug) are provided for wired headphones. Output level is adjusted
using the Volume UP/DN buttons on the remote control.
NOTE:

• Plugging a headphone into either jack will mute the Variable Audio Output.

SmartView Swivel Mechanism

The design of this mechanism provides the rear seat passengers a stable picture, viewable from
many different angles. This system allows the LCD to tilt from 90 to 120 degrees in 10 degree
steps. At the same time, the LCD will maintain its horizontal view while being rotated from left
to right, up to 30 degrees, in 10 degree steps.
NOTE:

• The LCD will only close when rotation is at 0 degrees to prevent damage to the monitor.

• When rotating the monitor, use both hands on either side of the panel to ensure even pressure

on the mechanism. This will prevent damage to the SmartSwivel mechanism.

• Make sure the panel is fully opened (90 degree position) before trying to rotate.

LCD Monitor Panel

This is a 6.8 inch, TFT, Active Matrix, LCD. In addition, an Infrared Wireless Headphone
transmitter is located on both sides of the LCD panel. When the monitor panel is closed, the
power is automatically turned off. Once power is OFF, power can only be turned ON by using
the Power button on the remote control (even after the panel is reopened).

Monitor Open Button

Press this button to release the Monitor Panel. The Panel will drop down slightly allowing you to
fully open to its 90 degree or greater position. To close, firmly press the LCD Monitor Panel
back up into the housing until a click is heard.

IR Sensor/Logo

There is an IR Sensor that receives the Remote Control commands at the front of the housing. At
this same location is a back-lit Alpine logo which acts as the main power indicator.

5