Alpine TME-M790 User Manual

TME-M790

MOBILE MULTIMEDIA MONITOR

• OWNER'S MANUAL
Please read before using this equipment.

• MODE D'EMPLOI
Veuillez lire avant d’utiliser cet appareil.

• MANUAL DE OPERACIÓN
Léalo antes de utilizar este equipo.

R

EN

DE

FR

ALPINE ELECTRONICS, INC.

Tokyo office: 1-1-8 Nishi Gotanda,

Shinagawa-ku,

Tokyo 141-8501, Japan

Tel.: [phone]

ALPINE ELECTRONICS OF AMERICA, INC.

19145 Gramercy Place, Torrance,

California 90501, U.S.A.

Tel.: 1-800-ALPINE-1 (1-800-257-4631)

ALPINE ELECTRONICS OF CANADA, INC.

Suite 203, 7300 Warden Ave. Markham,

Ontario L3R 9Z6, Canada

Tel.: 1-800-ALPINE-1 (1-800-257-4631)

Sankei Kikaku Co., Ltd.
1-13-38, Hinodai, Hino, Tokyo, Japan

ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.

6-8 Fiveways Boulevarde Keysborough,

Victoria 3173, Australia

Tel.: [phone]

ALPINE ELECTRONICS GmbH

Kreuzerkamp 7-11 40878 Ratingen, Germany

Via C. Colombo 8, 20090 Trezzano Sul Naviglio

Tel.: [phone]

ALPINE ITALIA S.p.A.

MI, Italy

Tel.: [phone]

ALPINE ELECTRONICS FRANCE S.A.R.L.

(RCS PONTOISE B 338 101 280)

98, Rue De La Belle Etoile, Z.I. Paris Nord Il

B.P. 50016 F-95945, Roissy, Charles De Gaulle

13 Tanners Drive, Blakelands, Milton Keynes

ALPINE ELECTRONICS DE ESPAÑA, S.A.

01013 Vitoria (Alava)-Apdo. 133, Spain

Cedex, France

Tel.: [phone]

ALPINE ELECTRONICS OF U.K., LTD.

MK14 5BU, U.K.

Tel.: [phone]

Portal De Gamarra 36, Pabellón 32

Tel.: [phone]

Designed by ALPINE Japan

Printed in Japan (S)

68P30540Y57-A

ES

ES

SE

Contents

ENGLISH

Operating Instructions

WARNING

WARNING.................................................. 2

CAUTION................................................... 3

PRECAUTIONS ......................................... 3

Basic Operations

Using Face Cover...............................................4

Initial System Start-up .......................................4

Raising the Monitor ...........................................4

Lowering the Monitor ........................................4

Turning Power On or Off...................................5

Selecting the Monitor Opening Angle ...............5

Adjusting the Monitor Viewing Angle...............5

Adjusting the Volume ........................................5

Switching the Source .........................................5

Switching Display Modes ..................................6

Other Useful Features

Adjusting Brightness of Picture .........................8

Adjusting Color Density of Picture ...................8

Adjusting Tint of Picture....................................8

Setting the Brightness of the Backlight .............9

Adjusting the Lowest Level of the Backlight .... 9

Setting Automatic Opening/

Closing of Monitor.............................................9

Selecting Rear Monitor ....................................10

Setting the External Device Interrupt Mode ....10

Switching the Opening Screen......................... 11

Turning Sound Guide Function On or Off.......11

Switching the Video Screen .............................11

Using the External Input Terminal ...................11

Operating with the Remote Control Unit

(RUE-4165 Sold Separately) ...........................12

Information

In Case of Difficulty ........................................13

Specifications...................................................13

Installation and Connections

Warning ............................................................14

Caution.............................................................14

Precautions.......................................................15

Installation .......................................................16

Connections .....................................................18

System Connections.........................................19

LIMITED WARRANTY

FR

ES

DE

IT

SE

1-EN

WARNING

WARNING

This symbol means important instructions.
Failure to heed them can result in serious
injury or death.

DO NOT OPERATE ANY FUNCTION THAT TAKES
YOUR ATTENTION AWAY FROM SAFELY DRIVING
YOUR VEHICLE.

Any function that requires your prolonged attention
should only be performed after coming to a complete stop.
Always stop the vehicle in a safe location before
performing these functions. Failure to do so may result in
an accident.

KEEP THE VOLUME AT A LEVEL WHERE YOU CAN
STILL HEAR OUTSIDE NOISE WHILE DRIVING.

Failure to do so may result in an accident.

MINIMIZE DISPLAY VIEWING WHILE DRIVING.

Viewing the display may distract the driver from looking
ahead of the vehicle and cause an accident.

DO NOT DISASSEMBLE OR ALTER.

Doing so may result in an accident, fire or electric shock.

DO NOT BLOCK VENTS OR RADIATOR PANELS.

Doing so may cause heat to build up inside and may result
in fire.

DO NOT WATCH VIDEO WHILE DRIVING.

Watching the video may distract the driver from looking
ahead of the vehicle and cause an accident.

INSTALL THE PRODUCT CORRECTLY SO THAT THE
DRIVER CANNOT WATCH TV/VIDEO UNLESS THE
VEHICLE IS STOPPED AND THE EMERGENCY BRAKE
IS APPLIED.

It is dangerous (and illegal in many states) for the driver
to watch TV/Video while driving a vehicle. Installing this
product incorrectly enables the driver to watch TV/Video
while driving. This may cause a distraction, preventing
the driver from looking ahead, thus causing an accident.
The driver or other people could be severely injured.

USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.

Use for other than its designed application may result in
fire, electric shock or other injury.

KEEP SMALL OBJECTS SUCH AS BATTERY OUT OF
THE REACH OF CHILDREN.

Swallowing them may result in serious injury. If
swallowed, consult a physician immediately.

DO NOT PLACE HANDS, FINGERS OR FOREIGN
OBJECTS IN INSERTION SLOTS OR GAPS.

Doing so may result in personal injury or damage to the
product.

USE THE CORRECT AMPERE RATING WHEN
REPLACING FUSES.

Failure to do so may result in fire or electric shock.

2-EN

CAUTION

PRECAUTIONS

This symbol means important instructions.
Failure to heed them can result in injury or
material property damage.

HALT USE IMMEDIATELY IF A PROBLEM APPEARS.

Failure to do so may cause personal injury or damage to
the product. Return it to your authorized Alpine dealer or
the nearest Alpine Service Center for repairing.

KEEP FINGERS AWAY WHILE THE MOTORIZED
FRONT PANEL OR MOVING MONITOR IS IN
MOTION.

Failure to do so may result in personal injury or damage
to the product.

Temperature

Be sure the temperature inside the vehicle is between
+45°C (+113°F) and 0°C (+32°F) before turning your unit
on.

Fuse Replacement

When replacing the fuse(s), the replacement must be of
the same amperage as shown on the fuse holder. If the
fuse(s) blows more than once, carefully check all
electrical connections for shorted circuitry. Also have your
vehicle’s voltage regulator checked.

Maintenance

If you have problems, do not attempt to repair the unit
yourself. Return it to your Alpine dealer or the nearest
Alpine Service Station for servicing.

Installation Location

Make sure the TME-M790 will not be exposed to:

• Direct sun and heat

• High humidity

• Excessive dust

• Excessive vibrations

• After turning the system off, a slight ghost of the image
will remain temporarily. This is an effect peculiar to
LCD technology and is normal.

• Under cold temperature conditions, the screen may
lose contrast temporarily. After a short warm-up
period, it will return to normal.

FR

ES

DE

3-EN

IT

SE

Basic Operations

9 8

RESET switch

PWR AUX

Using Face Cover

An anti-theft face cover is provided with the TME­M790.
Put the face cover onto the TME-M790 when you
leave the vehicle.
Be sure to remove the anti-theft face cover when
you drive.

OPEN/CLOSE

/ -

NOTES

• If the monitor touches an obstacle while it is
being raised, the unit will stop raising the
monitor immediately. Should this occur, remove the
obstacle and press the OPEN/CLOSE button again to
raise the monitor.

• When the movable monitor is opened, do not place
any object on the monitor and be careful not to bump
or apply any pressure to the monitor while it is open.
This can cause damage to the mechanism.

• Under low ambient temperature conditions, the
display may be dark for a short period of time
immediately after the power is turned on. Once the
LCD has warmed up, the display will return to
normal.

• For your safety, some operation of the unit
cannot be performed while the vehicle is in
motion. In this case, first stop the vehicle and
engage the parking brake, then perform the
operation.

Initial System Start-up

Immediately after installing or applying power to
the unit, it should be initialized.

1 At the lower left corner of the screen front panel,

there is a small button. Using a pencil or other
pointed object, press this RESET switch to
complete the initialization procedure.

Raising the Monitor

NOTE

The TME-M790 is a precision device. With careful
handling, its performance can be maintained at a high
level for a long time.

1 Press the OPEN/CLOSE button.

The unit beeps 3 times and raises the monitor
automatically.

4-EN

Lowering the Monitor

NOTE

The TME-M790 is a precision device. With careful
handling, its performance can be maintained at a high
level for a long time.

1 Press the OPEN/CLOSE button.

The unit will beep 3 times and lower the monitor
automatically.

NOTE

If the monitor touches an obstacle while it is being
lowered, the unit will stop lowering the monitor
immediately.
Should this occur, remove the obstacle and press the
OPEN/CLOSE button again to lower the monitor.

Turning Power On or Off

1 Press the PWR (Power) button to turn on the unit.

The opening screen appears automatically.

Adjusting the Monitor Viewing
Angle

Adjust the monitor's angle for better visibility.

2 Press the PWR (Power) button again to turn off

the unit.

NOTES

• The TME-M790 draws minimal current even
when its power switch is turned off. If the
switched power (ignition) lead of the TME­M790 is connected directly to the positive (+)
post of the vehicle's battery, the battery may be
discharged. If this lead is unswitched, it must
be disconnected from the battery post should
the vehicle be left unused for an extended
period of time.
An SPST (Single-Pole, Single-Throw) switch (sold
separately) can be added to simplify this procedure.
Then, you can simply place it in the OFF position
when you leave the vehicle. Turn the SPST switch
back ON before using the TME-M790. For
connecting the SPST switch, refer to the Installation.

• Some operation of the unit cannot be performed
while the vehicle is in motion. In this case, be sure to
first stop your vehicle and apply the parking brake,
then perform the operation.

• After turning the system off, a slight ghost of the
image will remain temporarily. This is an effect
peculiar to LCD technology and is normal.

• Under cold temperature conditions, the screen may
lose contrast temporarily. After a short warm-up
period, it will return to normal.

Selecting the Monitor Opening
Angle

1 While viewing the screen that is shown press the

9 or 8 button to adjust the display to the ideal
viewing angle.
The display viewing angle can be adjusted
between 40 and 105 degrees.

2 Press the 4 or 3 button to adjust the right-left

viewing angle. It is possible to adjust the display
viewing angle up to 15 degrees to the left or
right.
Press and hold the OPEN/CLOSE button for at
least 2 seconds to cancel the neck angle
adjustment.

NOTES

• The angle changes continuously if the 9 and 8
buttons or the 4 and 3 buttons are held down.

• If there are any obstructions to the monitor
when adjusting the angle, first remove the
obstruction and then readjust the angle.

• The screen color will vary when viewed at certain
angles. Adjust the screen angle for the best viewing
position.

• If the voltage of the vehicle's battery power is
low, the screen may blink when the screen angle is
changed. This is normal and not a malfunction.

• The adjusted angle is stored in the memory.

Adjusting the V olume

1 Press the or button to adjust the volume.

FR

ES

DE

The monitor opening angle can be set in 2
positions.

1 Press and hold the OPEN/CLOSE button for at

least 2 seconds while the monitor is being
raised. Each press changes the monitor angle
back or forth.

NOTE

When the OPEN/CLOSE button is pressed and held for
at least 2 seconds when the neck angle is adjusted, the
neck angle adjustment is canceled.
After doing this, adjust the display in the front/rear
direction.

NOTE

The volume changes continuously if the or
button is held down.

Switching the Source

1 Press the AUX button. Each press of the button

will cycle through the modes as follows:

NAVIGATION AUX1 AUX2

5-EN

IT

SE

Basic Operations

DISP

Switching Display Modes

Viewing the switching display modes

To watch a video source, your vehicle must be
parked with the ignition key in the ACC or ON
position. To do this, follow the procedure below.

1. Push the foot brake to bring your vehicle to a
complete stop at a safe location. Engage the
parking brake.

2. Keep pushing the foot brake and release the
parking brake once then engage it again.

3. While the parking brake is being engaged the
second time, release the foot brake.

NOTE

For automatic transmission vehicles, place the
transmission lever in the Park position.

The video lock-out system is now disabled.
Unless ignition is turned OFF, this mode can be
reactivated by simply engaging the parking
brake, without performing the entire procedure
above (1 through 3).
If the ignition is turned OFF position, you must
perform the entire procedure above.

1 Press and hold the DISP button for at least 2

seconds. Each press changes the display modes
as follows:

MODE 1 MODE 2 MODE 3 MODE 4

(WIDE) (ZOOM) (CINEMA) (NORMAL)

MODE 1 (WIDE)

Stretches the normal image evenly in a
horizontal direction so that it is displayed on the
entire screen.

NOTE

Trying to access the switching display modes while
driving will display the warning - PICTURE OFF
FOR YOUR SAFETY.

6-EN

MODE 2 (ZOOM)

Stretches the normal image evenly in a
horizontal direction so that it is displayed on the
entire screen. The stretching ratio increases the
closer to the left or right edge of the screen.

MODE 3 (CINEMA)

Stretches the normal image horizontally and
vertically.
The top and bottom of the screen is cut slightly
to adapt it to a cinema size image with a
proportion of 16:9.

MODE 4 (NORMAL)

FR

A normal television broadcasting (4:3) image is
displayed in the center (normal image).

ES

DE

IT

SE

7-EN

Other Useful Features

9 8

/ -

SET UP

Adjusting Brightness of Picture

NOTE

After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.

1 Press the SET UP button.
2 Press the 9 or 8 button within 10 seconds and

select BRIGHT.

3 Press the 4 or 3 button within 10 seconds to

adjust the brightness.

SET UP

AUX1

BRIGHT 0
COLOR 0
TINT 0
AUX OUT LINK

MIN MAX

1

3

4 Press the SET UP button to finish adjustments.

NOTE

If the AUX button is pressed and held for 2 seconds or
more while in the adjustment screen, the setting of the
brightness, color density, and tint is reset back to its
center value.

Adjusting Color Density of Picture

NOTE

After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.

1 Press the SET UP button.
2 Press the 9 or 8 button within 10 seconds and

select COLOR.

8-EN

AUX

3 Press the 4 or 3 button within 10 seconds to

adjust the color density.

SET UP

AUX1

BRIGHT 0
COLOR 0
TINT 0
AUX OUT LINK

–+

1

3

4 Press the SET UP button to finish adjustments.

NOTES

• If the AUX button is pressed and held for 2 seconds
or more while in the adjustment screen, the setting of
the brightness, color density, and tint is reset back to
its center value.

• The color density cannot be adjusted in the
NAVIGATION (RGB connection) mode.

Adjusting Tint of Picture

NOTE

After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.

1 Press the SET UP button.
2 Press the 9 or 8 button within 10 seconds and

select TINT.

3 Press the 4 or 3 button within 10 seconds to

adjust the tint.

SET UP

AUX1

BRIGHT 0
COLOR 0
TINT 0
AUX OUT LINK

RG

1

3

4 Press the SET UP button to finish adjustments.

NOTES

• If the AUX button is pressed and held for 2 seconds
or more while in the adjustment screen, the setting of
the brightness, color density, and tint is reset back to
its center value.

• The tint cannot be adjusted in the NAVIGATION
(RGB connection) mode.

Setting the Brightness of the
Backlight

It is possible to change the brightness of the LCD
panel's backlighting to more closely conform to
the vehicle's interior lighting. This makes the
screen easier to view.

3 Press the 4 or 3 button within 10 seconds to set

the value.

SET UP

AUX1

DIMMER AUTO
DIMMER Lv. ­OPEN/CLOSE
OUT INT. ON

LOW HIGH

OFF

2

3

NOTE

After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.

1 Press the SET UP button.
2 Press the 9 or 8 button within 10 seconds and

select DIMMER.

3 Press the 4 or 3 button within 10 seconds to set

the value.

AUTO:
Automatic adjustment of the screen brightness in
conformity with vehicle interior brightness.
HIGH:
Maximum screen brightness.
LOW:
The preset screen brightness that was set when
adjusting the minimum backlight level.

SET UP

AUX1

DIMMER AUTO
DIMMER Lv. ­OPEN/CLOSE
OUT INT. ON

HIGH LOW

AUTO

OFF

2

3

4 Press the SET UP button to finish adjustments.

4 Press the SET UP button to finish adjustments.

Setting Automatic Opening/
Closing of Monitor

Simply turn the ignition key to ACC ON or OFF to
automatically open or close the TV display.

NOTE

After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.

1 Press the SET UP button.
2 Press the 9 or 8 button within 10 seconds to

select OPEN/CLOSE.

3 Press the 4 or 3 button within 10 seconds to set

the value.

AUTO:
Automatic opening or closing of the display in
depending upon whether the ignition switch is ON
or OFF.
OFF:
Manual opening or closing of the display.

FR

ES

DE

Adjusting the Lowest Level of the
Backlight

It is possible with this equipment to adjust the
minimum brightness level for backlighting (LOW).
This is useful, for matching the screen brightness
to the dashboard for driving at night. This setting
is recalled with the AUTO setting corresponding
to the vehicle's interior lighting.

NOTE

After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.

1 Press the SET UP button.
2 Press the 9 or 8 button within 10 seconds and

select DIMMER Lv.

SET UP

AUX1

DIMMER AUTO
DIMMER Lv. ­OPEN/CLOSE
OUT INT. ON

OFF

AUTO

OFF

2

3

4 Press the SET UP button to finish adjustments.

9-EN

IT

SE

Other Useful Features

9 8

PWR

SET UP

Selecting Rear Monitor

This unit has controls to switch the video and
audio to a rear monitor if another (rear) monitor
is connected.

NOTE

After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.

/ -

V. SEL

Setting the External Device
Interrupt Mode

When used in conjunction with an Ai interception
box (KCA-801B), the sound of a TV or an
external input sound can be intercepted to an
Alpine head unit. This function may not work
with some combinations of products. For details,
refer to the KCA-801B’s operating instructions.

1 Press the SET UP button.
2 Press the 9 or 8 button within 10 seconds and

select AUX OUT.

3 Press the 4 or 3 button within 10 seconds to

carry out selection.

LINK:
Output the video/audio portion shown on the main
monitor, to the rear monitor.
NAV.:
Output the navigation video/audio to the rear
monitor. (Only when navigation unit is connected).
AUX 1:
Output the AUX 1 video/audio to the rear monitor.
AUX 2:
Output the AUX 2 video/audio to the rear monitor.

SET UP

AUX1

BRIGHT 0
COLOR 0
TINT 0
AUX OUT LINK

LINK NAV. AUX1 AUX2

1

3

NOTE

After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.

1 Press the SET UP button.
2 Press the 9 or 8 button within 10 seconds and

select OUT INT.

3 Press the 4 or 3 button within 10 seconds to

turn ON.

SET UP

AUX1

DIMMER AUTO
DIMMER Lv. ­OPEN/CLOSE
OUT INT. ON

OFF ON

OFF

2

3

4 Press the SET UP button to finish adjustments.

4 Press the SET UP button to finish adjustments.

10-EN

Switching the Opening Screen

9

Switching the Video Screen

You can change the opening screen to your liking.

NOTE

After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.

1 Press the SET UP button.
2 Press the

select H.U. IND.

3 Press the

set the selection.

ON:
Special opening screen.
This setting is used when combining with the
Flagship System model.
OFF:
Normal opening screen.

9

or 8 button within 10 seconds and

or 9 button within 10 seconds to

SET UP

AUX1

H.U. IND. ON

OFF ON

3

3

It is possible to change the video source for
display while retaining the present audio portion.

1 Press the V.SEL button.

NAVIGATION AUX1 AUX2

2 To release press and hold the V.SEL button for 2

seconds.

Using the External Input Terminal

It is possible to enjoy video and sound from a
video camera, etc. by simply connecting it with
an optional adapter cable.

Main unit

Video camera, etc.

AUDIO OUT

RLVIDEO OUT

Optional adapter cable
(RCA pin plugs
[yellow, red, white]

3.5ø miniplugs).

FR

ES

4 Press the SET UP button to finish adjustments.

Turning Sound Guide Function
On or Off

This function will give audible feedback with
varying tones depending upon the button
pressed.

1 Press and hold the PWR button for 2 seconds

with the power OFF and turn the Sound Guide
ON or OFF.

NOTE

With the above connections, video source switching and
settings and adjustments at adjustment screens are not
possible.

DE

IT

SE

11-EN

Other Useful Features

RUE-4165

Remote Control Signal Transmitter

2

D

L

O

V

ENT

L

U

P

V

O

N

1

DISP

SOURCE

LIST

DISP

MENU

DEFEAT

DETOUR

DISC

LIST

BAND

CANC.

MUTE

MP/RG

N/H

PLAN
CHG

V.SEL

DEL DEST.

4
6

r

A.PROC

VOICE

TUNER

POWER

ON/OFF

Signal Transmitter Indicator

5

3
7

8

t

9

q

(When the flip cover is open)

12

45

78

0

DEL

3

6

9

OK

Remote Control Sensor

Remote Sensor

(when the display
is stowed away)

• Point the remote control transmitter
toward the remote sensor on the TME­M790 and use the remote control within
2 meters from the TME-M790.

Remote Sensor

(when the display
is raised)

p
w

e

Operating with the Remote Control
Unit (RUE-4165 Sold Separately)

Button

RUE-4165 RUE-4165

No.

Select the item on the adjustment screen.
Moves to the left or right when you press
on the or side.

1

ENT

Moves up and down when you press
on the or side.

Volume increases when turned in a
clockwise direction.

2

Volume decreases when turned in a
counter-clockwise direction.

Volume increases.

3

4

5

6

7

8

9

LIST

DISP

NAVI / AUDIO

SOURCE

MENU

BAND

CANC.

MUTE

MP/RG

8

Changes continuously when held down.
Volume decreases.

Changes continuously when held down.
When operating this equipment,

change to the NAVI side.
Displays the adjustment screen.

Terminates the adjustment screen.

The display mode changes.
Display angle adjustment (left).

Changes continuously when held down.

Button

No.

p

q

w

e

r

t

9

DEL

OK

0

POWER

DISP

ON/OFF

V.SEL

DEL DEST.

NAVI / AUDIO

Display angle adjustment (right).
Changes continuously when held down.

Display angle adjustment (down).
Changes continuously when held down.

Display angle adjustment (up).
Changes continuously when held down.

When pressed less than 2 seconds:
OPEN/CLOSE of display.
When pressed at least 2 seconds:
Display slides forward and backward.

Power ON/OFF.

Switch the video source.

When switch 5 is set to the AUDIO side.

12-EN

Information

In Case of Difficulty

If you encounter a problem, please review the items in
the following checklist. This guide will help you isolate
the problem if the unit is at fault. Otherwise, make sure
the rest of your system is properly connected or consult
your authorized Alpine dealer.

No function or display.

• Car's ignition is off.

-Turn the ignition on.

• No fuse or blown fuse.

-Check the cause and replace the fuse.

• Incorrect connections.

-Check connection and remedy.

• Vehicle's battery is weak.

-Check the voltage of vehicle's battery.

Unclear picture display.

• Fluorescent tube is exhausted.

-Replace the fluorescent tube.*

No picture display.

• Brightness control is set for minimum brightness control.

-Adjust the brightness.

• Incorrect setting of the VCR mode.

-Switch to the correct mode.

• Protective circuit is on because of high temperature.

-Wait until the temperature inside the vehicle comes

down to the operating temperature range (45°C).

• Incorrect or open connection with the Monitor, AV
interface unit.

-Check the connection and remedy.

Picture color is poor.

• Brightness/Color/Tint control are not set to the proper
positions.

-Check each control.

Spots or dotted lines/stripes appear.

• Caused by neon signs, high-voltage power lines, CB
transmitter, other vehicle's ignition plugs, etc.

-Change the location of your vehicle.

The display angle cannot be adjusted or the
adjustment screen does not appear.

• Mechanism error.

-Press the OPEN/CLOSE button to stow away the
display, and raise the display again.

* The fluorescent tube replacement is not free of charge

even within the warranty period, for the tube is an article
of consumption.

Specifications

MONITOR SECTION

Screen Size 7.0"
LCD Type Transparent type TN LCD
Operation System TFT active matrix
Number of Picture Elements 336,960 pcs. (1,440 x 234)
Effective Number of
Picture Elements 99.99% or more
Illumination System Cold cathode

fluorescent tube

AV-INTERFACE UNIT SECTION

S/N Ratio

Video 45dB
Audio 55dB

Input Level

Video 1 Vp-p (75Ω UNBALANCED)
Audio 500mV (RMS)

Output Level

Video 1 Vp-p (75Ω UNBALANCED)
Audio 500mV (RMS)

GENERAL

Power Requirement 14.4V DC (11-15 V allowable)
Operating temperature +32ºF to +113º(0ºC to + 45ºC)
Weight
(Monitor Section) 2.0 kg (4 lbs. 7 oz)
(AV-Interface Unit Section) 0.2 kg ( 7 oz)

CHASSIS SIZE (Monitor section)

Width 178 mm (7")
Height 50 mm (2")
Depth 165 mm (6-1/2")

CHASSIS SIZE
(A V-Interface Unit section)

Width 106.6 mm (4-1/4")
Height 32 mm (1-1/4")
Depth 67.8 mm (2-11/16")

NOTES

• Due to continuous product improvement,
specifications and design are subject to change
without notice.

• The LCD panel is manufactured using an
extremely high precision manufacturing
technology. Its effective pixel ratio is over

99.99%. This means that there is a possibility
that 0.01% of the pixels could be either always
ON or OFF.

FR

ES

DE

IT

13-EN

SE

Installation and Connections

Before installing or connecting the unit, please
read the following and pages 2 and 3 of this
manual thoroughly for proper use.

Warning

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire
or product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE
GROUND.

(Check with your dealer if you are not sure.) Failure to do
so may result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM
THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due
to electrical shorts.

DO NOT ALLOW CABLES TO BECOME ENTANGLED
IN SURROUNDING OBJECTS.

Arrange wiring and cables in compliance with the manual
to prevent obstructions when driving. Cables or wiring
that obstruct or hang up on places such as the steering
wheel, gear lever, brake pedals, etc. can be extremely
hazardous.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying
capacity of the wire and result in fire or electric shock.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY
EXPERTS.

The wiring and installation of this unit requires special
technical skill and experience. To ensure safety, always
contact the dealer where you purchased this product to
have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL
THEM SECURELY.

Be sure to use only the specified accessory parts. Use of
other than designated parts may damage this unit
internally or may not securely install the unit in place.
This may cause parts to become loose resulting in hazards
or product failure.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
PINCHED BY A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like
the seat rails) or sharp or pointed edges. This will prevent
crimping and damage to the wiring. If wiring passes
through a hole in metal, use a rubber grommet to prevent
the wire’s insulation from being cut by the metal edge of
the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH
MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence
of moisture or dust. Moisture or dust that penetrates into
this unit may result in product failure.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR
STEERING SYSTEMS TO MAKE GROUND
CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or
any other safety-related system), or tanks should NEVER
be used for installations or ground connections. Using
such parts could disable control of the vehicle and cause
fire etc.

KEEP SMALL OBJECTS SUCH AS BATTERY OUT OF
THE REACH OF CHILDREN.

Swallowing them may result in serious injury. If
swallowed, consult a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT
HINDER VEHICLE OPERATION, SUCH AS THE
STEERING WHEEL OR GEARSHIFT.

Doing so may obstruct forward vision or hamper
movement etc. and results in serious accident.

14-EN

Precautions

• Be sure to disconnect the cable from the (–) battery
post before installing your TME-M790. This will
reduce any chance of damage to the unit in case of a
short-circuit.

• Be sure to connect the color coded leads according to
the diagram. Incorrect connections may cause the unit
to malfunction or damage the vehicle's electrical
system.

• When making connections to the car’s electrical
system, be aware of the factory installed components
(e.g. on-board computer). Do not tap into these leads to
provide power for this unit. When connecting the
TME-M790 to the fuse box, make sure the fuse for the
intended circuit of the TME-M790 has the appropriate
amperage. Failure to do so may result in damage to the
unit and/or the vehicle. When in doubt, consult your
ALPINE dealer.

• The TME-M790 uses female RCA-type jacks for
connection to other units (e.g. amplifier) having RCA
connectors. You may need an adaptor to connect other
units. If so, please contact your authorized ALPINE
dealer for assistance.

• The Display must be completely retracted in the casing
when installing. If it is not, problems may occur.

• When installing in automobiles, make sure the Display
can open/close without coming in contact with the shift
lever.

IMPORTANT

Please record the serial number of your unit in
the space provided below and keep it as a
permanent record. The serial number plate is
located on the bottom of the unit.

SERIAL NUMBER:
INSTALLATION DATE:
INST ALLATION TECHNICIAN:
PLACE OF PURCHASE:

FR

ES

15-EN

DE

IT

SE

Installation and Connections

Installation

Installing the Monitor

• Place of installation

Before determining the position of installation,
check that the display will not hamper gear
shifting when it is opened and closed in that
position.

NOTE

Install at an angle of within 30 degress from the
horizontal.

1

Mounting Sleeve
(Included)

Screws(M4x5)
(Included)

Dashboard

TME-M790

Mounting Bracket
(Included)

3

Lock Pin

Slide the TME-M790 into the dashboard. When
the unit is in place, make sure the locking pins
are fully seated in the down position. This can be
done by pressing firmly in on the unit while
pushing the locking pin down with a small
screwdriver. This ensures that the unit is properly
locked and will not accidentally come out from
the dashboard. Install the Supplied Front Frame.

Removal

1 Use a small screwdriver (or similar tool) to

push the locking pins to the “up” position (see
above drawing). As each pin is unlocked,
gently pull out on the unit to make sure it does
not re-lock before unlocking the second pin.

2 Pull the unit out, keeping it unlocked as you do

so.

<JAPANESE CAR>

Slide mounting sleeve from main unit (see
Removal Procedure below). Slide the mounting
sleeve into the dashboard. Install the supplied
bracket to the monitor.

2

Hex Nut
(M5)

Ground Lead

Chassis

Screw

Metal Mounting Strap

Bolt Stud

TME-M790

Front Frame
(Included)

Reinforce the monitor with the metal mounting
strap (not supplied). Secure the ground lead of
the unit to a clean metal spot using a screw (
already attached to the vehicle’s chassis.

NOTE

For the screw marked , use an appropriate
screw for the chosen mounting location.

To install using the vehicle's genuine bracket

TME-M790

Ground Lead

Screws
(M4x5)

Mounting Bracket

)

16-EN

Attaching the AV-Interface Unit

NAVIGATION

VIDEO

AUX INPUT 1

RL

AUX OUTPUT

AUDIO

VIDEO

AUDIO

RL

VIDEO

DISPLAY OUTPUT

(MONO) (MONO)
AUX INPUT 2

Velcro

When attaching with VelcroTM Tape, be sure to
choose a level location.
Do not attach in a location where the AV­Interface unit is upside down.
Attach the AV-Interface Unit.
Attach the Velcro

TM

Tape included with the AV­Interface Unit and secure the unit under the
passenger seat, for example.

Foot Brake Lead/Parking Brake Lead Connection

If necessary, use a pinch connector to connect the foot brake lead, parking brake lead, etc.

AUDIO

RL

TM

Tape (Included)

FR

12

TME-M790

Vehicle Cable

FOOT BRAKE

(Yellow/Black)

PARKING BRAKE

(Yellow/Blue)

Pinch Connector

Stopper

Pinch Connector

Pinch Connector

Monitor Cable

Foot brake lead

Parking brake lead

Foot brake lamp

Parking brake lamp

Foot brake switch

Parking brake switch

Plier

ES

Chassis

Battery

DE

Connection Diagram of SPST Switch (Sold Separately)

(If the ACC power supply is not available)

SPST SW (Optional)

IGNITION

TME-M790

(Monitor)

(Red)

BATTERY

(Yellow)

Battery

IT

NOTE

If your vehicle has no ACC power supply, add an SPST
(Single-Pole, Single-Throw) switch (sold separately).
If the switched power (ignition) lead of the TME­M790 is connected directly to the positive (+) post of
the vehicle’s battery, the TME-M790 draws some
current (several hundred milliamperes) even when its
switch is placed in the OFF position and the battery
may be discharged.

SE

17-EN

Installation and Connections

Connections

Monitor

White/Brown

White/Brown

Yellow/Black

Yellow/Blue

Pink/Black

8

Red

8

Yellow

Black

REMOTE OUT

AUX1

REMOTE OUT

AUX2

FOOT BRAKE

PARKING BRAKE

AUDIO

INTERRUPT OUT

IGNITION

BATTERY

GND

1

1

2

3

4

5

6

7

DISPLAY OUTPUT

AUX INPUT 2

(MONO) (MONO)

AUDIO VIDEO

RL

To remote input lead.

To remote input lead.

To the foot brake cord or brake lamp cord.

To the parking brake signal lead.

Connect to an IN INT compatible product.

Ignition key

Battery

AUDIO VIDEONAVIGATION R L

AUX OUTPUT

AUX INPUT 1

AUDIO VIDEORL

1 Remote Control Output Lead (White/Brown)

Connect this lead to the remote control input
lead. This lead outputs the controlling signals
from the remote control.

2 Foot Brake Lead (Yellow/Black)

Connect to the vehicle’s foot brake lead or brake
lamp lead.

3 Parking Brake Lead (Yellow/Blue)

Connect this lead to the power supply side of the
parking brake switch to transmit the parking
brake status signals to the TME-M790.

4 Audio Interrupt Out Lead (Pink/Black)
5 Switched Power Lead (Ignition) (Red)

Connect this lead to an open terminal on the
vehicle’s fuse box or another unused power
source which provides (+) 12V only when the
ignition is turned on or in the accessory position.

6 Battery Lead (Yellow)

Connect this lead to the positive (+) post of the
vehicle’s battery.

7 Ground Lead (Black)

Connect this lead to a good chassis ground on
the vehicle. Make sure the connection is made to
bare metal and is securely fastened using the
sheet metal screw provided.

8 Fuse Holder (5A)

To prevent external noise from entering the
audio system.

• Locate the unit and route the leads at least
10cm away from the car harness.

• Keep the battery power leads as far away from
other leads as possible.

• Connect the ground lead securely to a bare
metal spot (remove the coating if necessary) of
the car chassis.

• If you add an optional noise suppressor,
connect it as far away from the unit as possible.
Your Alpine dealer carries various Alpine noise
suppressors, contact them for further
information.

• Your Alpine dealer knows best about noise
prevention measures so consult your dealer for
further information.

18-EN

System Connections

AV-Interface unit

AUDIO VIDEORL

AUX INPUT 1

AUX OUTPUT

AUDIO VIDEONAVIGATION R L

1

2

3

AUDIO VIDEO

RL

(MONO) (MONO)

AUX INPUT 2

DISPLAY OUTPUT

4 9

Monitor

6

DVD Player

DVA-5205

7

(Sold separately)

8

KCE-150V

(Sold separately)

Monitor

(Sold separately)

ON
OFF

REMOTE OUT

AUX1

(White/Brown)

REMOTE OUT

AUX2

(White/Brown)

REMOTE IN

(White/Brown)

TV Tuner

(Sold separately)

Color Control

REMOTE IN

(White/Brown)

NOTE

When the DVA-5200 is connected for the DVD
Player, use the Ai-NET-PIN connection cord
KCA-120B (sold separately).

Rear

FR

ES

5

1 RCA Extension Cable (Included with DVD

Player)

2 RCA Extension Cable (Option)
3 RCA Extension Cable (Included with KCE-

150V)

4 RCA Extension Cable (Option)
5 RGB Cable (Navigation NVE-N851A: Included,

Navigation NVE-N871A: Sold separately)

6 Video Output Connector

Connect the AUX INPUT 1, Video Input Terminal
on the TME-M790 to the Video Output Connector
on the DVD player.

7 Audio Output Connector

Connect the AUX INPUT 1, Audio Input Terminal
on the TME-M790 to the Audio Output Connector
(L/R) on the DVD player.

Navigation

10

System

(Sold separately)

(NVE-N851A/NVE-N871A)

8 Video Output Terminal

Connect the AUX INPUT 2 Terminal on the TME­M790 to the Video Output Ter minal.

9 AUX Input T erminal

Connect the AUX OUTPUT Terminal on the TME­M790 to the AUX Input Ter minal.

p RGB Output Connector

Connect the NAVIGATION RGB Connector on
the TME-M790 to the RGB Output Connector on
the navigation system.

NOTES

• When this product is used in combination with a
separately sold Ai-NET-PIN connection cord (KCA­121B), the sound can be output to a head unit
equipped with an external input. For details, refer to
the head unit’s operating instructions.

• When the NVA-N751AS is connected for the
Navigation System, use the RGB conversion cable
KWE-503N (sold separately).

DE

IT

SE

19-EN

GARANTIE LIMITÉE

Fidèles à leur engagement de ne fournir que des produits de qualité, ALPINE ELECTRONIQUE DE L'AMERIQUE INC. et
ALPINE ELECTRONIQUE DU CANADA INC. (Alpine) sont heureuses de vous offrir cette garantie. Nous vous suggérons de le
lire attentivement et en entier. Si vous avez la moindre question, veuillez contacter l'un de nos concessionnaires ou appeler
directement Alpine au numéros Liste ci-dessous.

2



●

PRODUITS COUVERT PAR LA GARANTIE



Cette garantie couvre les produits audio/visuel de voiture et
les accessoires connexes ("le produit").
produits que dans le pays où il ont été achetés.



●

DURÉE DE LA GARANTIE



Cette garantie est en vigueur pendant un an à partir de la date
du premier achat du client.

Elle ne couvre les

● GARANTIE À VIE DES TÊTES DE LECTURE DES

MAGNÉTOPHONES À CASSETTES

Toutes les têtes de cassettes analogiques audio de voiture
Alpine, à l’exception des êtes de cassettes vidéo sont
garanties à vie contre des vices de fabrication pouvant
entraîner leur panne.



●

PERSONNES PROTÉGÉES PAR LA GARANTIE



Seul l'acheteur original du produit, s'il résisde aux États-Unis,
à Porto Rico ou au Canada, peut se prévaloir de la garantie.



●

CE QUI EST COUVERT



Cette garantie couvre tous les défauts de matériaux et de
fabrication (pièces et main d'œuvre) du produit.



●

CE QUI N'EST PAS COUVERT



Cette garantie ne couvre pas ce qui suit:

1

Les dommages survenus durant le transport des produits
renvoyés à Alpine pour être réparés (les réclamations
doivent être adressées au transporteur);

2

Tout dégât provoqué par accident, abus, négligence,
usage inapproprié, mauvais raccordement, mauvaise
utilisation ou par le non-respect des instructions
indiquées dans le manuel de l’utilisateur.

3

Les dommages dus à la force majeure, notamment aux
tremblements de terre, au feu, aux inondations, aux
tempêtes ou aux autres cataclysmes naturels;

4

Les frais ou les dépenses relatifs à l'enlèvement ou à la
réinstallation du produit;

5

Les services rendus par une personne, physique ou
morale non autorisée;

6

Les produits dont le numéro de série a été effacé, modifié
ou retiré;

7

Les produits qui ont été adaptés ou modifiés sans le
consentement d'Alpine;

8

Les produits qui ne sont pas distribués par Alpine aux
Etats-Unis, à Porto Rico ou au Canada;

9

Les produits qui n'ont pas été achetés par l'entremise d'un
concessionnaire Alpine autorisé;

Ä

Tout produit qui a été déterminé comme contenant une
quantité excessive de poussière ou de saleté et tout
produit qui contient d’autres saleté, en ce compris du
liquide et des corps étrangers.



●

COMMENT SE PRÉVALOIR DE LA GARANTIE



1

Il vous faut remettre le produit nécessitant des réparations
à un centre de service autorisé Alpine ou à Alpine même et
en assumer les frais de transport. Alpine a le choix entre
réparer le produit ou le remplacer par un produit neuf ou
révisé, le tout sans frais pour vous. Si les réparations sont
couvertes par la garantie et si le produit a été envoyé à un
centre de service Alpine ou à Alpine, le paiement des frais
de réexpédition du produit incombe Alpine.

Vous devez donner une description détaillée des
problèmes qui sont à l'origine de votre demande de
réparation.

3

Vous devez joindre la preuve de votre achat du produit.

4

Vous devez emballer soigneusement le produit pour éviter
tout dommage durant son transport.



●

LIMITATION DES GARANTIES TACITES



LA DURÉE DE TOUTES LES GARANTIES TACITES, Y
COMPRIS LA GARANTIE D'ADAPTATION A L'UTILISATION
ET LA GARANTIE DE QUALITÉ LOYALE ET MARCHANDE,
EST LIMITÉE À CELLE DE LA GARANTIE EXPRESSE
DÉTERMINÉE CI-DESSUS. PERSONNE N'EST AUTORISÉ
À ENGAGER AUTREMENT LA RESPONSABILITÉ D'ALPINE
EN VERTU DE LA VENTE D'UN PRODUIT.



●

EXCLUSIONS DE LA GARANTIE



ALPINE STIPULE EXPRESSÉMENT QU'ELLE N'EST PAS
RESPONSABLE DES DOMMAGES DOMMAGES-INTÉRÊTS
ET DOMMAGES INDIRECTS PROVOQUÉS PAR LE
PRODUIT. LES DOMMAGES DOMMAGES-INTÉRÊTS
SONT LES FRAIS DE TRANSPORT DU PRODUIT VERS UN
CENTRE DE SERVICE ALPINE, LA PERTE DE TEMPS DE
L'ACHETEUR ORIGINAL, LA PERTE D'UTILISATION DU
PRODUIT, LES BILLETS D'AUTOBUS, LA LOCATION DE
VOITURES ET TOUS LES AUTRES FRAIS LIÉS À LA
GARDE DU PRODUIT.
LES DOMMAGES INDIRECTS SONT LES FRAIS DE
RÉPARATION OU DE REMPLACEMENT D'AUTRES BIENS
ENDOMMAGÉS SUITE AU MAUVAIS FONCTIONNEMENT
DU PRODUIT.
LES RECOURS PRÉVUS PAR LES PRÉSENTES
EXCLUENT ET REMPLACENT TOUTE AUTRE FORME DE
RECOURS.



●

LIEN ENTRE LA GARANTIE ET LA LOI



La garantie vous donne des droits spécifiques, mais vous
pouvez aussi jouir d'autres droits, qui varient d'un état ou
d'une province à l'autre. En outre, certains états et certaines
provinces interdisent de limiter la durée des garanties tacites
ou d'exclure les dommages accessoires ou indirects. Dans ce
cas, les limites et les exclusions de la garantie peuvent ne pas
s'appliquer à vous.



●

CLAUSE APPLICABLE AU CANADA SEULEMENT



Pour que la garantie soit valable, il faut qu'un centre
d'installation autorisé ait installé le système audio pour l'auto
dans votre véhicule et qu'il ait ensuite apposé son cachet sur
la garantie.



●

NUMÉROS D'APPEL DU SERVICE À LA CLIENTELE



Si vous avez besoin de nos services, veuillez appeler le
centre de service autorisé Alpine le plus proche.

U.S.A. 1-800-ALPINE-1 (1-800-257-4631)
CANADA 1-800-ALPINE-1 (1-800-257-4631)

Alpine Électronique de L'Amérique, Inc., 19145 Gramercy Place, Torrance, California 90501, U.S.A.
Alpine Électronique du Canada, Inc., Suite 203, 7300 Warden Ave. Markham, Ontario L3R 9Z6, Canada

LIMITED WARRANTY

ALPINE ELECTRONICS OF AMERICA, INC. AND ALPINE OF CANADA INC. ("Alpine"), are dedicated to quality
craftsmanship and are pleased to offer this Warranty. We suggest that you read it thoroughly. Should you have any
questions, please contact your Dealer or Alpine at one of the telephone numbers listed below.

2



●

PRODUCTS COVERED:



This Warranty covers Car Audio/Visual Products and
Related Accessories ("the product"). Products purchased in
the Canada are covered only in the Canada. Products
purchased in the U.S.A. are covered only in the U.S.A.



●

LENGTH OF WARRANTY:



This Warranty is in effect for one year from the date of the
first consumer purchase.



●

LIFETIME TAPE HEAD WARRANTY:



All Alpine Car Audio analog tape heads excluding Video
tape heads are warranted for life against manufacturing
defects causing failure.



●

WHO IS COVERED:



This Warranty only covers the original purchaser of the
product, who must reside in the United States, Puerto Rico
or Canada.



●

WHAT IS COVERED:



This Warranty covers defects in materials or workmanship
(parts and labor) in the product.



●

WHAT IS NOT COVERED:



This Warranty does not cover the following:

1

Damage occurring during shipment of the product to
Alpine for repair (claims must be presented to the
carrier).

2

Damage caused by accident, abuse, negligence,
misuse, improper connections, improper operation or
failure to follow instructions contained in the Owner's
manual.

3

Damage caused by act of God, including without
limitation, earthquake, fire, flood, storms or other acts of
nature.

4

Any cost or expense related to the removal or
reinstallation of the product.

5

Service performed by an unauthorized person, company
or association.

6

Any product which has the serial number defaced,
altered or removed.

7

Any product which has been adjusted, altered or
modified without Alpine's consent.

8

Any product not distributed by Alpine within the United
States, Puerto Rico or Canada.

9

Any product not purchased from an Authorized Alpine
Dealer.

Ä

Any product that has been determined to contain an
excessive amount of dust or dirt and any product that
contains other contaminants including liquid or foreign
objects.



●

HOW TO OBTAIN WARRANTY SERVICE:



1

You are responsible for delivery of the product to an
Authorized Alpine Service Center or Alpine for repair
and for payment of any initial shipping charges. Alpine
will, at its option, repair or replace the product with a
new or reconditioned product without charge. If the
repairs are covered by the warranty, and if the product
was shipped to an Authorized Alpine Service Center or
Alpine, Alpine will pay the return shipping charges.

You should provide a detailed description of the
problem(s) for which service is required.

3

You must supply proof of your purchase of the product.

4

You must package the product securely to avoid
damage during shipment.



●

HOW WE LIMIT IMPLIED WARRANTIES:



ANY IMPLIED WARRANTIES INCLUDING FITNESS FOR
USE AND MERCHANTABILITY ARE LIMITED IN
DURATION TO THE PERIOD OF THE EXPRESS
WARRANTY SET FORTH ABOVE AND NO PERSON IS
AUTHORIZED TO ASSUME FOR ALPINE ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE OF THE
PRODUCT.



●

HOW WE EXCLUDE CERTAIN DAMAGES:



ALPINE EXPRESSLY DISCLAIMS LIABILITY FOR
INCIDENTAL AND CONSEQUENTIAL DAMAGES
CAUSED BY THE PRODUCT. THE TERM "INCIDENTAL
DAMAGES" REFERS TO EXPENSES OF
TRANSPORTING THE PRODUCT TO THE ALPINE
SERVICE CENTER, LOSS OF THE ORIGINAL
PURCHASER'S TIME, LOSS OF THE USE OF THE
PRODUCT, BUS FARES, CAR RENTALS OR OTHERS
COSTS RELATING TO THE CARE AND CUSTODY OF
THE PRODUCT. THE TERM "CONSEQUENTIAL
DAMAGES" REFERS TO THE COST OF REPAIRING OR
REPLACING OTHER PROPERTY WHICH IS DAMAGED
WHEN THIS PRODUCT DOES NOT WORK PROPERLY.
THE REMEDIES PROVIDED UNDER THIS WARRANTY
ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS.

● HOW STATE/PROVINCIAL LAW RELATES TO THE

WARRANTY:

This Warranty gives you specific legal rights, and you may
also have other rights which vary form state to state and
province to province. In addition, some states/provinces do
not allow limitations on how long an implied warranty lasts,
and some do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly,
limitations as to these matters contained herein may not
apply to you.



●

IN CANADA ONLY:



This Warranty is not valid unless your Alpine car audio
product has been installed in your vehicle by an Authorized
Installation Center, and this warranty stamped upon
installation by the installation center.



●

HOW TO CONTACT CUSTOMER SERVICE:



Should the product require service, please call the following
number for your nearest Authorized Alpine Service Center.

U.S.A. 1-800-ALPINE-1 (1-800-257-4631)
CANADA 1-800-ALPINE-1 (1-800-257-4631)

Alpine Electronics of America, Inc., 19145 Gramercy Place, Torrance, California 90501, U.S.A.
Alpine Electronics of Canada, Inc., Suite 203, 7300 Warden Ave. Markham, Ontario, L3R 9Z6, Canada