DVD NAVIGATION MAP
CARTE DE NAVIGATION DVD
MAPA DE NAVEGACIÓN DEL DVD
SMART MAP PRO
NVD-V002
DVD NAVIGERINGSKARTA
Prog. Ver. 2.00
OWNER'S MANUAL
Please read before using this disc.
MODE D'EMPLOI
Veuillez lire avant d'utiliser ce disque.
MANUAL DE OPERACIÓN
Lea este manual antes de utilizar este disco.
ANVÄNDARHANDLEDNING
Läs igenom handledningen innau du använder den här skivan.
R
Page 2
Precautions
PRECAUTIONS
IMPORTANT INFORMATION, PLEASE READ CAREFULLY BEFORE USING THIS PRODUCT.
This product is intended to safely provide
turn by turn instruction to get you to a
desired destination. Please read the following precautions to ensure that you use your
navigation system correctly.
LL
L This product is not a substitute for your
LL
personal judgment. Any route suggestions
made by the navigation system may never
supersede any local traffic regulations or
your personal judgment and/or knowledge
of safe driving practices. Do not follow
route suggestions if the navigation system
instructs you to perform an unsafe or illegal
maneuver, places you in an unsafe situation,
or routes you into an area which you consider unsafe.
LL
L Glance at the monitor screen only when
LL
necessary and safe to do so. If prolonged
viewing of the screen is necessary, stop the
vehicle in a safe and legal manner and
location.
LL
L Do not input destinations, change settings,
LL
or access any functions requiring a prolonged view of the monitor and/or remote
control while you are driving. Stop the
vehicle in a safe and legal manner and
location before attempting to access the
system.
LL
L Do not use the navigation system to route
LL
you to emergency services. Not all locations
of emergency service providers such as
police and fire stations, hospitals, and
clinics are contained in the database. Please
use your own judgment and your ability to
ask for directions in these situations.
LL
L The map database contained within the
LL
media (DVD ROM) in which it is stored is
the most recent map data available at the
time of production. Because of changes in
streets and neighbourhoods, there may be
situations where the navigation system may
not be able to route you to your desired
destination. In these cases, use your own
personal judgment.
2
LL
L The map database is designed to provide you
LL
with route suggestions, it does not take
account of the relative safety of a suggested
route, or of factors which may affect the time
required to reach your destination. The
database does not reflect road closures or
construction, road characteristics (i.e. type of
road surface, slope or grade, weight or height
restrictions, etc.), traffic congestion, weather
conditions, or any other factors which may
affect the safety or timing of your driving
experience. Use your personal judgment if
the navigation system is unable to provide
you with an alternate route.
LL
L There may be situations where the naviga-
LL
tion system may display the vehicle's
location erroneously. Use your own driving
judgment in this situation, taking into
account current driving conditions. Please
be aware that in this situation, the navigation system should correct the vehicle's
position automatically; however, there may
be times where you may have to correct the
position yourself. If this is the case, stop the
vehicle in a safe and legal manner and
location before attempting operation.
LL
L Make certain that the volume level of the
LL
monitor is set to a level which still allows
you to hear outside traffic and emergency
vehicles. Driving while unable to hear
outside sounds could cause an accident.
LL
L Please make certain that any other person
LL
who intends on using the navigation system
reads these precautions and the following
instructions carefully.
LL
L If there is anything in the manual which you
LL
do not understand, or are uncertain about the
operation of the navigation system, please
contact an authorized Alpine representative
before using the navigation system.
Page 3
Points to Observe for Safe Usage
a Read the manuals for this disc and the system
components carefully before using your navigation
system. They contain instructions on how to use the
system in a safe and effective manner. Alpine cannot be
responsible for problems resulting from failure to
observe the instructions in these manuals.
aMeaning of displays
Warning
Caution
This symbol means important instructions. Failure to heed them can
result in serious injury or death.
This symbol means important instructions. Failure to heed them can
result in injury or material property damage.
Warning
DO NOT OPERATE ANY FUNCTION THAT
TAKES YOUR ATTENTION AWAY FROM
SAFELY DRIVING YOUR VEHICLE. Any func-
tion that requires your prolonged attention should
only be performed after coming to a complete
stop. Always stop the vehicle in a safe location
before performing these functions. Failure to do
so may result in an accident.
DO NOT DISASSEMBLE OR ALTER THIS
PRODUCT. Doing so may result in an accident,
fire or electric shock.
a
This manual uses various pictorial displays to show you how
to use this product safely and to alert you to potential
dangers resulting from improper connections and operation.
Following are the meanings of these pictorial displays. It is
important to fully understand the meanings of these pictorial
displays in order to use this manual and the system properly.
MINIMIZE DISPLAY VIEWING WHILE DRIVING. Viewing the display may distract the driver
from looking ahead of the vehicle and cause an
accident.
DO NOT FOLLOW ROUTE SUGGESTIONS IF THE
NAVIGATION SYSTEM INSTRUCTS YOU TO
PERFORM AN UNSAFE OR ILLEGAL
MANEUVER, OR PLACES YOU IN AN UNSAFE
SITUATION OR AREA. This product is not a
substitute for your personal judgment. Any route
suggestions by this system should never supersede
any local traffic regulations or your personal judgment or knowledge of safe driving practice.
EN
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If
swallowed, consult a physician immediately.
USE THIS PRODUCT FOR MOBILE 12V
APPLICATIONS. Use for other than its designed
application may result in fire, electric shock or
other injury.
DO NOT PLACE HANDS, FINGERS OR
FOREIGN OBJECTS IN INSERTION SLOTS
OR GAPS. Doing so may result in personal
injury or damage to the product.
Tips
This indicates supplementary explanation of operation of the system.
Caution
HALT USE IMMEDIATELY IF A PROBLEM
APPEARS. Failure to do so may cause per-
sonal injury or damage to the product. Return it
to your authorized Alpine dealer or the nearest
Alpine Service Centre for repairing.
KEEP FINGERS AWAY WHILE THE MOTORIZED FRONT PANEL OR MOVING MONITOR
IS IN MOTION. Failure to do so may result in
personal injury or damage to the product.
3
Page 4
Precautions
User Agreement
In using this DVD-ROM "SMART MAP PRO" (hereinafter referred to as "Disk"), as part of
the Aisin AW Co., Ltd. ("Aisin AW") and Navigation Technologies Corporation ("NavTech")
Database (hereinafter referred to as "Database"), you are bound by the terms and conditions set forth below. By breaking the seal on this package, and using your copy of the
Database and Disk, you have demonstrated your agreement to the terms and conditions
of this Agreement. You should therefore, make sure that you read and understand the
following provisions.
• The Disk and Database may not be copied, duplicated, processed, or otherwise modified, in whole or in part, without the express written permission of Aisin AW, NavTech
and Alpine Electronics, Inc. ("Alpine").
• Neither the Disk nor the Database may be transferred or sublicensed to any third party
for profit, rent or loan, or licensed for reuse in any manners.
• The Disk and/or Database may not be decompiled, reverse engineered or otherwise
disassembled, in whole or in part.
• The Disk and Database may not be used in a network or by any other manner of simultaneous use in multiple systems.
• The Disk and Database are intended solely for personal use (or internal use where the
end-user business), or the consumer. The Disk and Database are not to be used for
commercial purposes.
• Neither Aisin AW, Alpine nor NavTech guarantees to the customer that the functions
included in the Disk and Database meet a specific objective of user.
• Neither Aisin AW, Alpine nor NavTech shall be responsible for any damages caused by
the use of the Disk and/or Database to the actual user and to any third party.
• The Warranty on the Disk and Database shall not extend to an exchange or refund due
to misspelling, omission of letters, or any other cosmetic discrepancy in layout found in
Disk and/or Database.
• The right to use the Disk and Database shall expire either when the user destroys this
software, or when any of the terms for use is violated and Aisin AW, Alpine and/or
NavTech exercises the option to revoke the license to use this software.
• The terms and conditions hereof apply to all subsequent users and owners as well as to
the actual purchaser.
WARNING
• Operation of the system while driving is dangerous. Users should stop vehicle
before operating the software.
• Road conditions and regulations take precedence over information contained
on the map display: observe actual traffic restrictions and circumstances while
driving.
• This software is designed for use exclusively in the NVE-N077PS series. It
cannot and may not be used in conjunction with other hardware.
4
Page 5
Table of Contents
2 .................................................................................Important Information
3 ............................................................. Points to Observe for Safe Usage
4 .......................................................................................... User Agreement
• This manual explains operation assuming that Alpine NVE-N077PS and RUE-4135 are used. If other model(s) are used, some display
screens may vary and locations of the buttons on the remote control are different (see "Buttons and functions of remote controls" on pages 43
and 44). For operation, refer to the manuals for the units you use in addition to this manual.
remote controls
45 .......................... In case of difficulty
46 ................. If this message appears
5
Page 6
Preface
Preface
Navigation terminology
Navigation
The navigation system displays and tracks the
vehicle's position and movement on a moving map
display. When a destination is input, the navigation
system quickly calculates a route and guides you
along the route with pictorial displays and voice
prompts.
Current vehicle position
The navigation system integrates the GPS (Global
Positioning Satellite) signals received and the map
information stored on the DVD ROM to display the
position and direction of the vehicle. The system
also includes a gyroscope and a speed sensor that
enable it to display the present position even in
locations where the GPS signals may be blocked.
Current vehicle
position
Map matching
Since GPS navigation has an error of 100 – 655 feet
(30 m – 200 m), the position of your vehicle may be
displayed off the road. Map matching automatically
corrects this error so that the position of your vehicle
is displayed on the road.
Road preference setting
You can set your preferred road on the route to the
destination for up to 2 places if your local knowledge
helps.
Memory points
Locations you go to frequently
can be stored into memory and
marked on the map. The
system can store up to 200
points, excluding your home.
You can add icons at the
memory points so that the
system also displays the
icons on the map.
Memory point mark
Motorway-preference selection
When searching for routes with the navigation
system, you can switch between searching for
routes that give priority to motorways and those that
give priority to ordinary roads. When you specify
motorway preference, the navigation system
automatically searches for a route that gives priority
to motorways and guides you along that route.
Destination
The point on the map that is
your destination is specified
and displayed with the
destination icon. You can set
up to 5 destinations for the
same journey.
Route
When a destination is input,
the navigation system
automatically calculates a
route and displays it in blue
on the map.
6
Destination icon
Route
(Blue)
Page 7
Features
• Automatic Route Calculation
Just select the destination and your navigation
system does the rest, automatically searching for
the route you need.
• Real Time Voice Guide
A voice guide informs you of the distance and
direction until your course changes, giving advice
timed to match road conditions.
The VOICE button lets you repeat the last voice
guide when needed by just pushing the button.
• Dual-screen Display
Two different maps or guidance screens can be
displayed simultaneously. For example, the map
screen and the arrow-guide screen, or the map
screen and the motorway screen.
• Direct Inputting of Phone
Number
By inputting the phone number of a place or a
memory point you have stored, the system can
search for it as the destination.
• Voice Guidance at an Exit or
Junction on Motorways
When you approach an exit or junction on the
motorway, the system gives you voice guidance
using the same name as shown on the road
signboards.
• Eight Languages Selectable for
the Voice Guidance
You can choose one of the eight languages
(German, English, French, Italian, Dutch, Swedish,
Spanish or Danish) for the voice route guidance.
• Multiple-Destination Setting
You can set up to 5 destinations in any order you
like for the same journey.
• Intersection Zoom
As you near intersections and cross points, the
map display automatically zooms in to show a
more detailed view that you will need. This means
there is no need to press the zoom buttons.
• Built-in Gyroscope and Speed
Sensors
The gyroscope for sensing direction and the speed
pulse sensor for detecting distance provide data
which allows the vehicle position and direction to be
displayed even in locations where the GPS signals
cannot be received such as between high buildings
or in tunnels.
• Motorway Information Display
When you travel on motorways, the basic guidance
display (with an arrow) automatically shows the
distances to the next fuel station/restaurant/parking/
junction (except exit).
EN
• Map Zooming
You can change the map display in 13 magnification
scales (50,100, 200, 400, 800, 1K, 3K, 6K, 10K,
20K, 50K, 100K and 200K metres) to show more
detailed or wider views by pressing the 3 or 4
button on the remote control.
• Direct Input of Name of Place of
Interest
Input only the name of a place of interest (without
inputting the city name) to search for the route to
the place of interest.
7
Page 8
Before Using The System
Before Using The System
Rewriting operating system programme
If a different version of the map disc is used with
your navigation system, the operating system
programme installed will be rewritten automatically
to read this SMART MAP PRO disc.
Remove the different version of the
map disc from your navigation
1
system. Insert this SMART MAP
PRO disc. (For removing and
inserting procedures, refer to the
Owner's Manual of the system.)
The system starts rewriting of the operation
system programme. While the programme
is being rewrited, do not turn the power off
and on to the system, or do not eject the
disc.
The opening screen appears in the
display.
2
Notes:
• If a different version of the map disc is
inserted after the system programme has
been rewritten, the selection menu appears
in the display.
• If the user model is either "NVD-V001," or
"NVD-V001S," and upgraded, "NAME2"
memory point contents already registered
are erased.
• For the locations and functions of the remote
control's buttons, see pages 43 and 44.
8
Page 9
Switching the display on or off
With the Alpine navigation system, when the
ignition key is turned to ACC or ON and the
display monitor is set in navigation display mode
or external input display mode, the opening
screen will be automatically displayed.
For operation of the remote control, see pages 43
and 44 and the Owner's Manual for your system.
After the opening screen is displayed, important information say-
1
ing "CAUTION" and the language
selection menu are automatically
displayed.
There are eight languages to choose
from. Select (highlight) your disired
language for the picture/voice
guidance and texts by tilting the
joystick on the remote control, then
press the ENTER button on the top
of the joystick to execute the
selection. The important information
changes to the selected language.
Be sure to read the important
information.
Language selection menu
After you have read this important
information, select "I agree" and
2
press the ENTER button.
The map screen is displayed.
To turn off the display monitor,
press the ON/OFF button on the
3
remote control.
When you press the ON/OFF button again,
the display monitor is turned on and the
opening screen is displayed.
Tips:
• If there is no disc in the navigation system,
"No DVD. Please insert map DVD." is
displayed. For details on how to load or
remove the disc, refer to the "Inserting a
disc" and "Removing a disc" sections in the
manual for the navigation system.
• If the inserted disc cannot be read, the
"Unable to read data. Check if map DVD is
correct." message is displayed. Load the
correct disc.
• If the monitor is kept on with the engine off
for an extended period of time, the battery
may discharge.
EN
9
Page 10
Before Using The System
How to switch the map displays
Once the route setting has been performed and
travelling started, the navigation system provides
the driver all of the major route information with
real time voice directions and guidance displays.
You can manually select the desired guidance
displays for your convenience.
Point Display
Distance
in a straight
line from the
current
vehicle
position.
Operation
guide
Scale
←→
*GPS signal state
No icon: No satellite information being received
or satellite signals are being calculated.
Icon is displayed: Receiving GPS signals
(in 2-dimentional or 3-dimentional).
The distance between
400 m
the arrows on the screen
is 400 metres ( mile).
Reticule icon
1
4
Distance to the
destination
Estimated required time.
3-D Display for
Motorway Junction
The Current Vehicle Position Display is automatically displayed when travelling starts. Pressing the
4 or 3 button on the remote control while the
map is being displayed the map will be zoom in or
out. To return to the current vehicle position
screen display from other screen displays, press
the POS. button.
During navigation, when your vehicle approaches an intersection, the Zoomed Intersection Map of that intersection is displayed. This
enlarged Intersection Map gives you further
information via voice guidance.
(Sometimes, the enlarged crossroads map is
displayed even when you are going to go
straight.)
Zoomed Intersection
Map Display
• Ordinary Road:
Name of next road
ahead.
• Motorway:
Name of next
junction ahead.
Distance to the intersection
Map orientation
Shows the map orientation for
up on the current map.
N: North
Current Vehicle
Position Display
: North up
: Heading up
(The arrowhead shows the
direction of north. To change
the map orientation, see page
12.
Information on the next
intersection.
Route.
Street name.
←
Current vehicle position icon.
→
Dual - Screen Display
10
Motorway junction
Note:
Applicable to some areas in
Germany and UK only.
Right screenLeft screen
Page 11
Main menu and sub-menu
Use the main menu to select a variety of the
system's functions. Select (highlight) a desired
main menu item and press the ENTER button.
The sub-menu for the selected main menu item
automatically appears in the display.
Press the MENU button on the
remote control to display the main
1
menu when the navigation system is
on.
For the locations of the buttons on the
remote control, see pages 43 and 44.
Operation guide
The main menu appears on the
display.
2
Volume
(see page 41)
The display shows the sub-menu for
the selected main menu item.
4
Highlight (select) a desired submenu item by tilting the joystick and
press the ENTER button.
The screen example shows when
"Destination" is selected.
This bar indicates that
there is a continuation
of the list.
Tilt the joystick to scroll
the list.
Searching country
(For details, see
page 13.)
Use when you delete
the destination.
Note:
Press the POS. button to return to the current
vehicle position screen.
EN
Tilt the joystick to select (highlight)
a desired main menu item.
Make sure that the desired main
menu item is highlighted, then press
3
the ENTER button on the top of the
joystick to execute the selection of
the menu item.
11
Page 12
Before Using The System
Point setting menu
When a desired point is searched for using the
Destination or Memory points menu etc. and the
map for the point area is displayed, the point
setting menu is displayed. This menu is very
When the point map is displayed
using the Destination menu
When the point map is displayed using
the Memory points menu
useful when you set the searched point as a
destination or memory point.
After selecting a menu item, press ENTER.
Map scroll: Select this menu to manually scroll the map
with the joystick.
Enter: Use this menu when you set the point as a
destination or an additional destination, and calculate the
route.
To set the selected point as an additional destination,
select "Enter" from the point setting menu and press
ENTER. The Set destination menu appears, select "Add"
and press ENTER.
Info.: Choose this menu when you want to get some
information about the point such as address, phone
number, etc. when the point is searched for using POI
menu.
Change: Select this menu when you want to change the
conditions in searching for a route, such as motorway
preference.
Map scroll : Select this menu to manually scroll the map.
12
Enter: Use this menu when you set the point as a
memory point or avoid area.
Info.: Choose this menu when you want to get some
information about the point such as address, phone
number, etc. when the point is searched for using POI
menu.
When the ENTER button is pressed while
a map screen without the point setting
menu is displayed
Map orient.: Select this menu when you want to change
the map orientation for the current map display.
POI: Use this menu when you want to display the POI
icons on the map or to display the “Local POI list” for the
displayed POIs.
: This menu appears only when multiple
destinations are set. Use it when you specify the desired
destination.
Change route: Choose this menu when you want to
change to another route (this menu is displayed only
when the route has already been set).
Mark: You can store the point as a memory point.
Right screen: Select this menu when dual-screen mode is
selected and you want to edit the map orientation and the
icon display on the right screen. (See page 29.)
Guide: Use this menu when you want to check the POI
icons set on the map. If you select the desired POI icon
by tilting the joystick and pressing ENTER, the detailed
information of the POI is displayed.
Page 13
Basic Operation
Deciding the route
There are three procedures to decide an appropriate route to your desired destination; searching for
the location, searching for the route, and deciding
the route.
This section describes the operational procedures
when a destination is searched for using its
address as an example.
Press the MENU button on the
remote control to display the main
1
menu.
Select (highlight) "Destination" from
the main menu by tilting the joystick
2
on the remote control and press the
ENTER button on the top of the
joystick.
and press ENTER. (Select the 8 or 9
indicator on the display and press ENTER to
scroll the area list.) When you have selected
the desired area, choose "OK" by tilting the
joystick and press ENTER.
The street or town name input
alphabet table automatically
4
appears. Tilt the joystick to select
the desired character for the first
position of the street name and
press ENTER. The input character
appears at the first position of the
text window. Repeat this procedure
to input the entire street name.
Tips:
• When 1 character is input, the candidates for
the next character are narrowed down.
• Selecting "/" returns to the previous
numeral and erases it.
EN
The Destination search menu
automatically appears. Select
3
"Address" from the Destination
search menu by tilting the joystick
and press the ENTER button.
Note:
When you search for a location in another
country (area), you should change the search
country (area). In this case, select "Change"
by tilting the joystick and press ENTER. The
Search area menu appears, select the
desired area (country) by tilting the joystick
Searching
country
(This example
shows when
Germany is
selected.)
When the street name inputtings
have been completed, the list of the
5
input street names appears. Select
the desired street name by tilting the
joystick and press ENTER.
(To be continued)
13
Page 14
Basic Operation
The house number input table
appears automatically. Input the
6
house number in the same manner
as step 4 above. When the house
number inputtings have been
completed, select "List" by tilting the
joystick and press ENTER.
The map showing the area of the
input address with the point setting
7
menu appears. Select "Enter" by
tilting the joystick and press ENTER.
Tips:
You can search for a location from various
items as shown below.
The system starts calculation of the
route. When the calculation is
8
completed, the whole route is
displayed.
When you start driving this route,
the system displays the map with
9
the current vehicle position and
begins guidance.
Current vehicle
position
14
Page 15
Selecting from the route menu (three routes searching)
The system calculates up to three routes simultaneously including the recommended route. You
can choose any one of the routes.
When you have selected a desired
destination, the navigation system
1
calculates up to 3 routes and the
system automatically displays the
"All-route" screen.
Press ENTER while the All-route
screen is displayed.
2
a 3 routes: Displays the 3 Routes screen.
EN
The list showing information about the
distance and required time to the
destination is displayed.
The route menu appears.
Select the desired route menu item
3
and press ENTER.
The route menu items:
a Start: Starts the route guidance.
Note:
If you want to view the drive simulation to
check the details of the route, select "Start"
then press and hold the ENTER button for at
least 5 seconds while the whole route screen
is displayed. (For more information, see page
42.)
a Edit route: Displays the Edite route
screen. For details, see page 30.
15
Page 16
Basic Operation
Suspending or resuming the
route guidance
You can very easily suspend the route guidance
temporarily and resume it.
Note:
The route information remains in memory even if
the route is cancelled. To erase the route information delete the destination, see "Erasing the route"
(next section).
Press the MENU button to display
the main menu.
1
To temporarily suspend the route
guidance, select "Suspend
2
guidance" in the main menu by
tilting the joystick and press ENTER.
Erasing the route
Press the MENU button to display
the main menu.
1
Select "Edit route" from the main
menu by tilting the joystick and
2
press ENTER.
Select "Delete" under "Destination"
3
and press ENTER.
16
1-02-2
Note:
When the guidance is suspended, the main
menu automatically changes to show
"Resume guidance."
To resume the route guidance,
select "Resume guidance" in the
3
main menu by tilting the joystick
and press ENTER.
Note:
If multiple destinations are set, the Delete
destination screen showing the list of the
destinations appears. Select the destination
to be deleted (or "Del. All" to delete all
destinations) by tilting the joystick and
press ENTER.
The confirmation dialog message
appears. Select "Yes" by tilting the
4
joystick and press ENTER if you
want to delete the destination(s) and
route.
Page 17
Registering your home
Register your home first. When your home is
registered, you can recall it very quickly and
setting the route for returning home is simple.
Press the MENU button to display
the main menu.
1
Select "Memory points" from the
main menu by tilting the joystick
2
and press ENTER.
To search for your home location,
select the searching method
4
described in the Searching for a
Destination section on page 18.
When the map showing the area of
your home is displayed, press
5
ENTER.
EN
The sub-menu appears. Select
"Register home" by tilting the
3
joystick and press ENTER.
Note:
You can register only one home. If your home
has already been registered, the system
shows "Delete home" menu. Select "Delete
home" and press ENTER to delete the
previously registered home (for details, see
page 38). Then, register new home.
Press the "POS." button to return to
the current vehicle position map.
6
17
Page 18
Searching For Destinations
Searching For Destinations
Searching for a destination from its address
If you know the address of the desired destination,
you can easily display that point on the map by
just inputting the address.
Press the MENU button to display
the main menu. Select "Destination"
1
from the main menu by tilting the
joystick and press ENTER.
The sub-menu for "Destination"
appears. Select "Address" by tilting
2
the joystick and press ENTER.
Notes:
• If your destination is located in other country
than that currently selected one, be sure to
change the searching country.
•
To change the searching country, choose
"Change." The menu appears, select the
desired searching country.
The street name input table for the
3
destination appears. Select the
character for the first position of the
street name by tilting the joystick
and press ENTER. The entered
character appears at the first
position of the text window. Repeat
this procedure to complete the
character inputtings of the street
name.
c /
Returns to the previous character/numeral
and erases it.
d Character with diacritical mark/numeric
pallet
Select the desired pallet.
e Number of candidates
Tips:
• When 1 character/numeral is input, the
candidates for the next character/numeral
are narrowed down (and the others are
shaded).
• You can also search for a location by
inputting just the start of its name and
selecting "List" and pressing ENTER.
•
If the number of candidate locations is
narrowed down, the list of the candidate
locations will be displayed automatically.
Select the desired location from the list and
press ENTER.
• If you want to display the list of candidate
street names, select "List"and press ENTER.
When "City" is selected and ENTER
is pressed, the city selection menu
appears. Select the desired menu
item.
• When "Input city name" is selected, input
the city name and press ENTER.
• When "5 near cities" is selected, the names
of 5 near cities appears in the display. Select
the desired city name and press ENTER.
• When a city name is directly selected from
the list displayed, press ENTER.
• When "All cities" is selected, the character
input pallet will be displayed. Input the city
name.
18
a
a Text windows
Display the selected characters/numerals.
b List
Displays a list of the candidate names for
the selected characters/numerals.
e
c
b
d
Page 19
The list of street names will be
displayed. Select the desired street
4
name and press ENTER.
Notes:
• If there are other streets with the same
name in other cities when the desired street
name is searched for in "All cities" mode,
the list of the city names will be displayed.
Select the desired city name and press
ENTER.
• If there is no location with the input
spelling, locations with similar spelling are
displayed.
The house number input table
appears. Input the house number in
5
the same manner as for inputting
the street name (step 3 above).
When the house number inputtings
have been completed, select "List"
by tilting the joystick and press
ENTER.
The map screen showing the
selected area with the point setting
6
menu appears.
Note:
For details of the point setting menu, see
page 12.
EN
Notes:
• Your desired destination can be searched for
more precisely by inputting the house number.
• If there is no house number or no data in the
disc, the system displays the map showing
the area of the input street name.
19
Page 20
Searching For Destinations
Searching for a point of interest (POI)
If you know the name of the desired point of
interest (POI), you can easily display that point of
interest on the map by just inputting its name.
Press the MENU button to display
the main menu. Select "Destination"
1
by tilting the joystick and press
ENTER.
The sub-menu appears. Select "POI"
by tilting the joystick and press
2
ENTER.
There are three ways in searching
for your desired POI. The Input POI
3
name screen with the character
input table appears.
• By inputting the name:
1. Input the name of a POI you want to
search for by tilting the joystick and
pressing ENTER in the same manner as
inputting the street name (see page 18).
• From the city name
1. Select "City" by tilting the joystick and
press ENTER. The city selection menu
appears, select the desired menu item.
• When "Input city name" is selected,
input the city name.
• When "5 near cities" is selected, the
names of 5 near cities appears in the
display. Select the disired city name
and press ENTER.
• When a city name is directly selected
from the list displayed, press the
ENTER button.
• When "All cities" is selected, the
character input pallet will be
displayed. Input the city name.
• From the category
1. Select "Category" by tilting the joystick
and press ENTER.
2. The category selection menu appears.
Select the desired category by tilting the
joystick and press ENTER.
Select "List" by tilting the joystick
and press ENTER. The list of the
4
candidate POIs and the number of
the POIs appear. Select the desired
POI by tilting the joystick and press
ENTER.
Note:
If you select "Name," "Category" or "City," you
can narrow down the number of the
candidates.
The map screen showing the area of
the selected POI and the point
5
setting menu appears.
Note:
For details of the point setting menu, see
page 12.
20
Page 21
Setting the local point icon
display
Searching for the local POIs
using the their icons
The system can display on the map the icons for
the points of interest such as petrol stations,
restaurants, parking lots, etc.
While a map screen is being
displayed, press ENTER.
1
The point setting menu appears.
Select "POI" from the point setting
2
menu by tilting the joystick and
press ENTER.
The show POI icons screen is
displayed. Select a desired POI icon
3
by tilting the joystick and press
ENTER.
The system can search for the POIs in a range of
30 km (19 miles) around the reticule icon and
when POI icons are set you can display their icons
with the distance to the POIs. The system can
also display only the POIs along the set route.
While a map screen is being
displayed, press ENTER.
1
The point setting menu appears.
Select "POI" from the point setting
2
menu by tilting the joystick and
press ENTER.
The show POI icons screen appears.
Select "Local POI list" by tilting the
3
joystick and press ENTER.
The list of the Local POIs appears.
4
EN
Notes:
• If you want to display multiple icons, select
"More" by tilting the joystick and press
ENTER. Then, select the desired icons one
by one. When all selections have been
completed, select "OK" and press ENTER.
• You can set up to 5 POI icons.
• If you select "POI off," the POI icons do not
appear on the map.
• If you select “Guide” from the point setting
menu, you can obtain the information about
the POI icon displayed on the map. For
details, see “Point setting menu” on page 12.
Notes:
• You can sort the list by distance, icons or
names.
• You can list up to 100 places to display.
Select the desired local POI by
tilting the joystick and press ENTER.
5
The map showing the area of the
selected POI with the point setting
menu appears.
Note:
For details of the point setting menu, see
page 12.
You can sort the
list by distance,
icons or names.
When this menu
is selected, the
system can list
the POIs along
the set route.
21
Page 22
Searching For Destinations
Searching from Telephone
number
If you have input phone number in your memory
points, you can easily display a desired memory
point as your destination by just inputting the
phone number. For inputting phone numbers for
the memory points, see page 35.
Press the MENU button to display
the main menu. Select "Destination"
1
from the main menu by tilting the
joystick and press ENTER.
The sub-menu appears. Select
"Telephone no." by tilting the
2
joystick and press ENTER. The
numeric input table appears.
Input the phone number including
the area code by tilting the joystick
3
and pressing ENTER. (For details of
inputting number, see step 5 on
page 19.)
When the desired phone number
has been input, select "OK" and
press ENTER.
Searching from memory points
If memory points have already been registered,
you can call them out with a simple operation and
choose a desired location as the destination. For
details on the registration method, see page 34.
Press the MENU button to display
the main menu. Select "Destination"
1
from the main menu by tilting the
joystick and press ENTER. Select
"Memory point" from the sub-menu
by tilting the joystick and press
ENTER.
The list of the memory points is
displayed. Select the memory point
2
you wish to display by tilting the
joystick and press ENTER.
Tips:
• The phone number can also be input using
the numeric keypad on the remote control.
For operation, see the Remote Control
Reference Guide page 43.
• When 1 numeral is input, the candidates for
the next numeral are narrowed down (and
the others are shaded).
• Selecting "/" returns to the previous
numeral and erases it.
The area map of the location with
the input phone number is displayed
4
with the point setting menu.
Note:
For details of the point setting menu, see
page 12.
The reticule icon appears at the
selected memory point on the map
3
with the point setting menu.
Note:
For details of the point setting menu, see
page 12.
22
Page 23
Searching for homeSearching from intersection
If your home has already been registered, you can
call it out with a simple operation. For details
about the registration method, see page 17.
Press the MENU button to display
the main menu. Select "Destination"
1
from the main menu by tilting the
joystick and press ENTER.
The sub-menu appears. Select
"Home" by tilting the joystick and
2
press ENTER.
Searching from previous
destinations searched
The system automatically stores up to 20 locations the system have searched for as destinations.
Press the MENU button to display
the main menu. Select "Destination"
1
from the main menu by tilting the
joystick and press ENTER.
The sub-menu appears. Select
"Prev. dest." by tilting the joystick
2
and press ENTER.
If you know an intersection near where you want
to go, you can input two cross streets as your
destination. This section describes how to locate a
destination by entering two cross street names.
Press MENU button to display the
main menu. Select "Destination"
1
from the main menu by tilting the
joystick and press ENTER.
The sub-menu appears. Select
"Intersection" by tilting the joystick
2
and press ENTER.
The intersection input table for the
1st street name and 2nd street name
3
appears. Input the 1st street name
by tilting the joystick and pressing
ENTER in the same manner as for
inputting the address for Searching
For Destinations (step 3 on page 18).
The 2nd street name input table
appears. Input the 2nd street name.
4
When two street names have been
input, the map screen showing the
5
area of the selected intersection
with the point setting menu appears.
EN
The list showing the destinations
stored in memory is displayed.
3
Select the desired destination from
the list by tilting the joystick and
press ENTER.
This bar indicates
that there is a
continuation of
the list. Tilt the
joystick to scroll
the list.
The map of the selected destination
appears with the point setting menu.
4
Notes:
• For details of the point setting menu, see
page 12.
• The stored location in memory can be
erased. For details, see page 38.
Note:
For details of the point setting menu, see
page 12.
23
Page 24
Searching For Destinations
Searching from motorway
entrance/exit
You can search for a location from the motorway
entrance or exit.
Press the MENU button to display
the main menu. Select "Destination"
1
from the main menu by tilting the
joystick and press ENTER.
The sub-menu appears. Select
"Motorway entrance/exit" by tilting
2
the joystick and press ENTER. The
Motorway Ent./Exit input pallet
appears.
Input the desired motorway name by
tilting the joystick and press ENTER.
3
When the inputtings of the
motorway name have been
4
completed, the list of the input
motorways appears. Select the
correct motorway by tilting the
joystick and press ENTER.
Searching from start point
When a route has been set, the start point of the
route is stored in memory. You can easily call out
the start point when you want to return to the start
point.
Press the MENU button to display
the main menu. Select "Destination"
1
from the main menu by tilting the
joystick and press ENTER.
The sub-menu appears. Select
"Prev. start point" by tilting the
2
joystick and press ENTER.
The map showing the previous start
point and the point setting menu
3
appears.
Note:
For details of the point setting menu, see
page 12.
24
The Motorway Ent./Exit screen
appears. Select "Entrance" or "Exit"
5
as desired by tilting the joystick and
press ENTER.
The list of the entrances or exits of
the selected motorway appears.
6
Select the desired entrance or exit
by tilting the joystick and press
ENTER.
The map showing the area of the
selected entrance or exit of the
7
motorway with the point setting
menu is displayed.
Notes:
• When the number of candidates narrows
down, the list of candidates is displayed
automatically.
• For details of the point setting menu, see
page 12.
Page 25
Searching by scrolling
displayed map
The displayed map can be freely scrolled with the
joystick in eight directions to search for a desired
destination.
The best way to find a location is first to display the
wide range map and specify the approx. location.
You can find the desired location efficiently by
specifying more and more detailed maps. (Press
the
tion.)
1
2
3
4 or 3
button to change the map magnifica-
Press the MENU button to display
the main menu. Select "Destination"
from the main menu by tilting the
joystick and press ENTER.
The Destination screen appears.
Select "Map" by tilting the joystick
and press ENTER.
The map screen with the current
vehicle position appears. Select
"Map scroll" by tilting the joystick
and press ENTER.
EN
Search for a desired destination by
4
scrolling the map with the joystick.
The map scrolls in the direction in
which the joystick is tilted. Bring the
destination point on the map under
the reticule icon and press ENTER.
The point setting menu appears.
For details of the point setting menu,
see page 12.
Notes:
• There are two map scrolling speeds,
depending on how long the joystick is tilted.
• To return to the previous screen, press the
RETURN button.
• To return to the current vehicle position,
press the POS. button.
25
Page 26
Route Checking
Overviewing the searched route
We recommend that before you begin driving the
route, you look at the entire route in the overview
display.
Press the MENU button to display
the main menu. Select "Route
1
overview" from the main menu by
tilting the joystick and press ENTER.
The entire route is displayed on a
map with a large enough view that
2
you can view the entire route.
Tips:
With the route overview screen displayed, if
you press the ENTER button the screen
shown below appears.
Activates route
guidance mode.
Displays the turn
list (see the
example below).
Goes to route
editing mode.
26
Example of turn list
When you press the POS. button,
the system return to the current
3
vehicle position map screen.
Page 27
Previewing the searched route
When this mode is selected, the reticule icon for the current vehicle position moves along the searched
route so that you can preview the route. You can also search for the POIs along the route.
Press the MENU button to display the main menu. Select "Route preview" from
the main menu by tilting the joystick and press ENTER.
1
The route preview screen with operation menu is displayed.
2
Select this menu to scroll the map using
the joystick.
Select this menu to change the map
orientation.
This menu appears only when there are
POI icons along the route.
You can display the POI information.
Select this menu to display the Edit route
preview menu as shown below.
Select the desired menu to move the
reticule icon along the route to go to the
destination/POI selected or to return to
the current vehicle position.
EN
Press the POS. button to return to the current vehicle position screen.
3
27
Page 28
Guidance Screen Configuration
Guidance map display
Your desired guidance map display modes can be
selected for your convenience as follows.
Press the MENU button to display
the main menu. Select "Screen
1
config." from the main menu by
tilting the joystick and press ENTER.
Single screen
display
The Screen configuration selection
menu is displayed. Select a desired
2
menu item by tilting the joystick and
press ENTER.
Arrow screen
display
Dual-screen display
Turn list display
Motorway information
display
Map screen display
28
Page 29
Dual-screen display
The system can display two different screens
simultaneously for your convenience. For example, a detailed map and a wide range map can be
displayed at the same time so that you can view a
detailed map around the present vehicle position
and a wide range map along the route.
Press the MENU button to display
the main menu. Select "Screen
1
config." from the main menu by
tilting the joystick and press ENTER.
The Map configuration screen
appears (see page 28). Select "Dual"
2
under "Map mode" by tilting the
joystick and press ENTER.
Note:
Pressing the
screen display.
The System changes to dual-screen
mode and displays two screens
3
simultaneuusly. Press ENTER while
two screens are displayed.
button switches to the dual-
• To display the set local POI icons, select
"Show POI icons" by tilting the joystick and
press ENTER.
• To change the map magnification range,
press the 4 or 3 button.
• If a wider-range map is being displayed, the
icons cannot be displayed. In this case,
change to a detailed map by pressing the 3
button.
When the settings have been
completed, press the POS. button to
6
return to the current vehicle position
map. Now, the system displays two
different screens.
EN
The point setting menu appears. To
change display mode of the right
4
screen, select "Right screen" from
the point setting menu by tilting the
joystick and press ENTER.
The Edit right screen menu appears.
5
• To change the map orientation, select "Map
orient." menu by tilting the joystick and press
ENTER. Each pressing of ENTER toggles
between north-up and heading-up modes.
29
Page 30
Route Editing
Adding destinations
This operation is for setting multiple destinations
for the same journey (up to 5).
Press MENU button to display the
main menu. Select "Edit route" from
1
the main menu by tilting the joystick
and press ENTER.
The "Edit route" screen appears.
Select "Add" under "Destination" by
2
tilting the joystick and press ENTER.
The Destination searching screen is
displayed. For details of searching
3
for the desired destinations, see
pages 18 to 25.
Reordering destinations
The sequence of the destinations to go can be
changed in any order you like.
Press the MENU button to display
the main menu. Select "Edit route"
1
from the main menu by tilting the
joystick and press ENTER.
The Edit route screen appears.
Select "Reorder" under
2
"Destination" by tilting the joystick
and press ENTER.
The list of the Input destinations
appears. Select the destinations one
3
by one in the desired sequence of
arrival by tilting the joystick and
pressing ENTER.
When the sequence of the
destinations has been changed,
4
select "OK" by tilting the joystick
and press ENTER.
When the map showing the area of
the selected destination with the
4
point setting menu is displayed,
select "Enter" by tilting the joystick
and press ENTER.
The Add Destinations screen
showing the sequence of the
5
destinations is displayed. Select
"Add" at the place where the new
destination should be added by
tilting the joystick and press ENTER.
Note:
To add more destinations (up to 5 in all),
repeat this procedure.
When you have set all the
destinations, select "OK" by tilting
6
the joystick and press ENTER.
When the settings have been
completed, select "OK" by tilting the
5
joystick and press ENTER.
30
Page 31
Deleting destinations
This section describes how to delete an input
destination or all of the input destinations at the
same time.
Press the MENU button to display
the main menu. Select "Edit route"
1
from the main menu by tilting the
joystick and press ENTER.
The Edit route screen appears.
Select "Delete" under "Destination"
2
by tilting the joystick and press
ENTER.
The list of the Input destinations
appears. Select the destination you
3
want to delete by tilting the joystick
and press ENTER.
(If you want to delete all of the
destinations at the same time, select
"Del. All" by tilting the joystick and
press ENTER.)
Note:
If only one destination is set, the list will not
appear.
Setting required (preferred)
roads for the route
Press the MENU button to display
the main menu. Select "Edit route"
1
from the main menu by tilting the
joystick and press ENTER.
The Edit route screen appears.
Select "Add" under "Set required
2
road" by tilting the joystick and
press ENTER.
The map showing the entire route
appears. Scroll the map and bring
3
the road to be edited under the
reticule icon by tilting the joystick
and press ENTER.
The confirmation screen appears. If
you prefer to use the road, select
4
"Enter" by tilting the joystick and
press ENTER. (If you want to change
to another type of road, select
"Next" to choose another road.)
EN
The confirmation dialog screen
appears. Select "Yes" by tilting the
4
joystick and press ENTER. The
selected destination (or all of the
destinations) will be deleted.
When the sequence of the
destinations has been changed,
5
select "OK" by tilting the joystick
and press ENTER.
The Add required road screen
appears. Select "Add" located at
5
where the required road should be
placed by tilting the joystick and
press ENTER.
Note:
If only one destination is set, the list will not
appear.
Note:
You can set 1 or 2 required roads.
When you have set the required
road, select "OK" by tilting the
6
joystick and press ENTER.
31
Page 32
Route Editing
Modifying the set required
roads
Press the MENU button to display
the main menu. Select "Edit route"
1
from the main menu by tilting the
joystick and press ENTER.
The Edit route screen appears.
Select "Modify" under "Set required
2
road" by tilting the joystick and
press ENTER.
The list showing the sequence of the
set roads to go through appears.
3
When you have set only one
waypoint on the route, skip this step
and go to step 4. When you have set
multiple waypoints, select the road
to be modified by tilting the joystick
and pressing ENTER.
Deleting the set required roads
Press the MENU button to display
the main menu. Select "Edit route"
1
from the main menu by tilting the
joystick and press ENTER.
The Edit route screen appears.
Select "Delete" under "Set required
2
road" by tilting the joystick and
press ENTER.
The list showing the sequence of the
set required roads to go through
3
appears. When you have set only
one waypoint on the route, skip this
step and go to step 4. When you
have set multiple waypoints, select
the set required road to be deleted
by tilting the joystick and press
ENTER. (If you want to delete all of
the set required roads, select "Del.
All" by tilting the joystick and press
ENTER.)
32
The road selected in step 3 above
appears on the map. Scroll the map
4
by tilting the joystick to bring the
required road under the reticule icon
and press ENTER.
The dialog message appears. Select
"Enter" by tilting the joystick and
5
press ENTER.
(If the road is not preferred one,
select "Next" by tilting the joystick
and press ENTER.)
When settings have been
completed, select "OK" by tilting the
6
joystick and press ENTER.
The confirmation dialog screen
appears. Select "Yes" by tilting the
4
joystick and press ENTER. The
selected required road is deleted.
When the required road(s) have
been deleted, select "OK" by tilting
5
the joystick and press ENTER.
Page 33
Changing the conditions for
the route searching
You can change the conditions for the route
searching between the current vehicle position to
a destination or only a portion of the route.
Press the MENU button to display
the main menu. Select "Edit route"
1
from the main menu by tilting the
joystick and press ENTER.
The Edit route screen appears.
Select "Search condition" by tilting
2
the joystick and press ENTER.
The search condition list screen
appears. Select the route between
3
the points to be edited and choose
the desired condition (Quick, Short,
etc.) by tilting the joystick and press
ENTER. You can specify the
searching condition for other
portions of the route as well.
Setting the route options
The navigation system can search for 4 different
types of routes: using motorway, toll road, ferry
and restricted road.
Press the MENU button to display
the main menu. Select "Edit route"
1
from the main menu by tilting the
joystick and press ENTER.
The Edit route menu appears. Select
"Road preference" by tilting the
joystick and press ENTER.
The Road preferrance menu
appears. Select "Allow" or "Detour"
423
for the item to be edited by tilting
the joystick and press ENTER.
EN
When the searching conditions have
been specified, select "OK" by
4
tilting the joystick and press ENTER.
When the editing for the route
option has been completed, select
4
"OK" by tilting the joystick and
press ENTER. The navigation
system starts the calculation of the
route.
33
Page 34
Memory Points
Memory Points
Storing locations in memory
You can store up to 200 special points on the map
in memory, such as locations you go to frequently
or scenic locations. The locations stored in
memory can be recalled quickly.
Press the MENU button to display
the main menu. Select "Memory
1
points" from the main menu by
tilting the joystick and press ENTER.
The Memory points menu appears.
Select "Register" under "Memory
2
points" by tilting the joystick and
press ENTER.
The Register memory points with
the searching menu appears. Search
3
for a desired point. To search for a
point, see pages 18 to 25.
When the point searched for and the
point setting menu is displayed,
4
select "Enter" by tilting the joystick
and press ENTER.
Editing the memory points
You can change the point marks, names, phone
numbers, etc. of the memory points.
Press the MENU button to display
the main menu. Select "Memory
1
points" from the main menu by
tilting the joystick and press ENTER.
The Memory point menu appears.
Select "Edit" under "Memory points"
2
by tilting the joystick and press
ENTER.
The list of the memory points
appears. Select the memory point to
3
be edited by tilting the joystick and
press ENTER.
You can sort
by the date,
icons or
names.
The Reqister memory point mark
(icon) selection screen is displayed.
5
Select the desired point mark by
tilting the joystick and press ENTER.
Note:
When you select "With sound" and press
ENTER, the sound menu appears. Select
your desired sound to be produced when you
come near the memory point. If the voice
guidance and the memory point sound
happened to come at the same time, the
voice guidance has priority.
Press the POS. button to return to
the present vehicle position screen.
6
The Edit memory point screen
appears. Select the item to be edited
4
by tilting the joystick and press
ENTER.
a
b
c
d
a Icon
You can select an icon for the registered
point from a number of icons.
H Go to a1 Icon change.
b Name
You can give a name to a registered point
and set to show it or not.
H Go to b2 Name change.
34
Page 35
c Location
The location of a memory point can be
moved.
H Go to c1 Location Change.
d Phone no.
Phone number can be added to a
registered point.
H See d1 Phone Number Change.
Icon Change
Select "Change" for "Icon" and
press ENTER.
a1
The icon list appears. Select the
desired icon and press ENTER.
a2
Location Change
Select "Change" for "Location" and
press ENTER.
c1
The location to be corrected is
indicated by the reticule icon. Tilt
c2
the joystick and move the map to
the correct location.
Press ENTER.
c3
Phone Number Change
Select "Change" for "Phone no."
and press ENTER.
d1
EN
Name Change
Select "Change" for "Name" and
press ENTER.
b1
The character input pallet is
displayed.
b2
Select the desired characters one by
one and press ENTER each time you
select a character.
When character inputtings have
b3
been completed, select "OK" and
press ENTER.
Note:
To show the name, select "On" and press
ENTER. If you do not want to show the name,
select "Off" and press ENTER.
Backspace
Erases the
previous
character
The numeric input pallet is
displayed. Select the desired
d2
numeral and press ENTER. Repeat
this procedure to complete the
editing.
When the new phone number has
been input, select "OK" and press
d3
ENTER.
Tips:
Phone Number Editing:
You can search for a desired destination or
point of interest using the phone number that
is input or edited here. (See page 22.)
When the editing has been
completed, press the POS. button to
5
return to the current vehicle position
screen.
35
Page 36
Memory Points
Deleting the memory points
Press the MENU button to display
the main menu. Select "Memory
1
points" from the main menu by
tilting the joystick and press ENTER.
The Memory points screen appears.
Select "Delete" under "Memory
2
points" by tilting the joystick and
press ENTER.
The list of the Delete memory points
appears. Select the memory point to
3
be deleted by tilting the joystick and
press ENTER.
(To delete all of the memory points
at the same time, select "Del. all" by
tilting the joystick and press
ENTER.)
Storing the avoid points in
memory
The system can store up to 10 avoid areas which
you do not want to pass through. In the route
calculation, the system searches for a route which
does not include the avoid areas.
Press the MENU button to display
the main menu. Select "Memory
1
points" from the main menu by
tilting the joystick and press ENTER.
The Memory points screen appears.
Select "Register" under "Area to
2
avoid" by tilting the joystick and
press ENTER.
The Register area to avoid screen
appears. To search for an area to be
3
avoided, see pages 18 to 25.
The map showing the area selected
with the point setting menu appears.
4
Select "Enter" by tilting the joystick
and press ENTER.
The confirmation dialog message is
displayed. Select "Yes" by tilting the
4
joystick and press ENTER to
execute the deletion.
Press the POS. button to return to
the current vehicle position screen.
5
The Change area size screen
appears. Select the desired avoid
5
area size from five boxes displayed
by tilting the joystick and press
ENTER.
Area size
selector
Note:
The system accepts the settings only when
the map magnification ratio is from 50 m to
800 m.
Press the POS. button to return to
the current vehicle position screen.
6
36
Page 37
Editing the avoid areas
Deleting the stored avoid points
You can change the names, locations, and the
area size of the stored avoid areas.
Press the MENU button to display
the main menu. Select "Memory
1
points" from the main menu by
tilting the joystick and press ENTER.
The Memory points screen appears.
Select "Edit" under "Area to avoid"
2
by tilting the joystick and press
ENTER.
The list of the stored avoid arears is
displayed. Select the avoid area to
3
be changed by tilting the joystick
and press ENTER.
The Edit area to avoid screen
appears.
4
Press the MENU button to display
the main menu. Select "Memory
1
points" from the main menu by
tilting the joystick and press ENTER.
The Memory points screen appears.
Select "Delete" under "Area to
2
avoid" by tilting the joystick and
press ENTER.
The list of the stored avoid areas is
displayed. Select the avoid area to
3
be deleted by tilting the joystick and
press ENTER.
(If you want to delete all of the
stored avoid areas at the same time,
select "Del. all" by tilting the joystick
and press ENTER.)
EN
• Name:
Select "Change" for "Name" and press
ENTER. The name input pallet appears.
Input the new name and select "OK" and
press ENTER.
• Location:
Select "Change" for "Location" and press
ENTER. The avoid area map appears.
Move the map to bring the reticule icon to
the point where you want to avoid by tilting
the joystick and press ENTER.
• Change area size:
Select this menu and press ENTER to
change the avoid area size. Select the
desired size by tilting the joystick and press
ENTER.
When the editing has been
completed, press the POS. button to
5
return to the current vehicle position
screen.
The confirmation dialog message
appears. Select "Yes" by tilting the
4
joystick and press ENTER. The
selected avoid area(s) are deleted.
Press the POS. button to return to
the current vehicle position screen.
5
37
Page 38
Memory Points
Deleting the registered home
You can register only one home, so if you want to
edit the registered home, you should delete the
previously registered home and register new one.
Press the MENU button to display
the main menu. Select "Memory
1
points" from the main menu by
tilting the joystick and press ENTER.
The Memory points screen appears.
Select "Delete home" by tilting the
joystick and press ENTER.
Note:
If your home is not yet registered in memory,
the display shows "Register home."
The confirmation message for
deletion is displayed. Select "Yes"
423
by tilting the joystick and press
ENTER to execute the deletion.
Deleting the stored previous
destinations
Press the MENU button to display
the main menu. Select "Memory
1
points" from the main menu by
tilting the joystick and press ENTER.
The Memory points screen appears.
Select "Del. prev. dest." by tilting the
2
joystick and press ENTER.
The Delete previous dest. screen
showing the list of the previous
3
destinations appears. Select the
previous destination to be deleted
by tilting the joystick and press
ENTER.
(If you want to delete all of the
previous destinations, select "Delete
all" by tilting the joystick and press
ENTER.)
38
Press the POS. button to return to
the current vehicle position screen.
4
The confirmation dialog message
appears, select "Yes" by tilting the
4
joystick and press ENTER.
Press the POS. button to return to
the current vehicle position screen.
5
Page 39
Customizing Setups
How to change the setups
Press the MENU button to display
the main menu. Select "Set up" from
1
the main menu by tilting the joystick
and press ENTER.
The Set up screen appears. Select
the desired item to be customized
2
by tilting the joystick and press
ENTER.
"Distance"
Selects km or miles.
3a
Note:
For English, you can select the distance
indications in either miles or km.
For other languages, only kilometres are used
for the distance indications.
"Notify seasonal restrict."
Turns the display of the seasonal
3b
restrictions on or off.
"Estimated travel time"
Turns on or off the estimated travel
3c
time display.
When "Change speed" is selected,
the graphic screen appears in the
display. Select the desired menu
item and tilt the joystick to the right
or left to increase or decrease the
average speed respectively. When
settings have been finished, select
"OK" by tilting the joystick and
press ENTER to end the setting
procedure.
"Auto reroute"
Turns on or off the automatic
3
d
rerouting function when the vehicle
deviated from the original route.
"Voice guide in all mode"
Use this menu when a device having
e
3
voice interrupt function such as
CVA-1003 is connected to the
system. In this case, set to the ON
position.
"Current street name"
f
Turns the display of the current
3
street name on or off.
"Map colour (day), (night)"
g
Selects normal colour or special
3
colour.
Note:
"day" means when the head lamps are off and
"night" means the head lamps are on.
"Operation guide on map"
h
Turns the display of the operation
3
guide on or off.
EN
Operation guide
Note:
To go back to the original settings, select
"Default."
"Screen adjust"
Use when you adjust the screen
3i
position. For details, see next page.
When the settings have been
completed, select "OK" by tilting the
4
joystick and press ENTER.
Note:
To return to the initial settings, select "Default"
by tilting the joystick and press ENTER.
39
Page 40
Customizing Setups
Others
Screen position adjustment
For some TV monitors that can be connected to
the navigation system, the screen display will be
out of place. Adjust the display position to match
the TV monitor you connect to the system.
Press the MENU button to display the
main menu. Select "Set up" from the
1
main menu by tilting the joystick.
The Set up screen appears. Select
"Screen adjust" by tilting the
2
joystick and press ENTER.
The screen position adjustment
screen is displayed.
3
Adjust the display position by tilting
the joystick.
The display screen moves the way you tilt
the joystick.
When the adjustment has been
completed, press ENTER.
The screen is displayed at the adjusted
position.
Vehicle position/direction
correction
If the actual position/direction of your vehicle and
the position/direction of the current vehicle position icon on the map differ (for example, when you
moved on a ferry boat), you can manually correct
the position/direction of the current vehicle position icon with the following method.
The system's map matching feature automatically
corrects the error when you drive the vehicle
several miles in good GPS signal reception area.
Press the MENU button to display the
main menu. Select "Set up" from the
1
main menu by tilting the joystick and
press ENTER.
The Set up screen appears.
"Calib." by tilting the joystick and
2
press ENTER.
The Calibration screen is displayed.
Select "Pos./Direction" by tilting the
3
joystick and press ENTER.
Select
40
Tilt the joystick in 8 directions to
correct the position. When the
4
correction has been completed,
press ENTER.
Tilt the joystick toward left and right
to correct the direction. When the
5
correction has been completed,
press ENTER.
Page 41
Resetting after tyre replacement
Adjusting the volume level for
the navigation system
Resetting is required when the vehicle's tyres are
replaced. Be sure to perform the following resetting procedure when the vehicle's tyres are
replaced.
Press the MENU button to display
the main menu. Select "Set up" from
1
the main menu by tilting the joystick
and press ENTER.
The Set up screen appears. Select
"Calib." from the Set up screen by
2
tilting the joystick and press ENTER.
The Calibration screen appears.
Select "Tyre change" from the
3
Calibration screen by tilting the
joystick and press ENTER.
You can adjust the volume level of the beep
sound that is produced when the remote control is
operated and the volume level of the voice guide.
Press the MENU button to display
the main menu. Select "n" from the
1
main menu by tilting the joystick
and press ENTER.
Volume
The volume adjustment screen
appears. You can adjust the volume
2
level in seven steps from 1 to 7.
Select the desired level by tilting the
joystick and press ENTER.
Note:
When you want to turn off the sound of the
navigation system, select "Off" and press
ENTER.
EN
Press the POS. button to return to
the current vehicle position screen.
3
41
Page 42
Others
Drive simulation
To check the searched route, you can carry out a
drive simulation. The icon for the current vehicle
position moves along the searched route indicating the contents of guidance that will be provided.
When the calculation of the route
has been completed, the display
1
shows the entire route on the map.
For details, see the searching for a
route on page 13.
While the entire route is being
displayed, press ENTER.
2
The point setting menu appears.
Select "Start" from the point setting
3
menu by tilting the joystick, then
press and hold ENTER for at least 5
seconds.
The drive simulation starts.
To stop the drive simulation, press
4
the RETURN button. The display
returns to the current vehicle
position screen.
42
Page 43
Reference
Buttons and functions of remote controls
RUE-4135
Joystick/ENTER button
Selects highlighted items in menus and
moves map displays and vehicle position
icon. Tilt and hold this to scroll at a higher
speed. Press the ENTER button to select
any highlighted function, screen icon or
street segment.
Zoom/Scroll buttons
Change map magnification ratio upward or
downward in 13 steps. When the button is
pressed momentarily, the map
magnification ratio changes one step.
When the button is pressed and held, the
map magnification ratio changes
contineuously. Scroll through street, city or
category listings a page at a time.
AUDIO/NAV. switch
Switches between Audio and
Navigation operations.
Pressing this button illuminates the
highlighted portion of the display.
LO.PT. (Local Point) button
Press to diaplay the information of
the set POI.
The "Local POI list" screen is
displayed.
ROUTE button
Press to change the set route. "Change
route" screen is displayed.
DEST. (Destination) button
Displays the destination menu.
ON/OFF button
Turns the pictorial display on or off.
DEL. DEST. button
Deletes current destination.
(Deletes only the next
destination to go to.)
TEL. button
Displays the telephone number inputting screen.
Remote Control transmitter
Transmits the remote control signals.
Aim toward the display monitor for
operation.
S
O
U
/
i
5
8
A.PROC.
2
F
U
N
C
O
P
/
C
L
0
V. SEL.
R
C
E
MENU
B
A
N
D
VOICE
3
6
.
9
. PT.
M
OK
U
M
.
L
O
V
E
T
LO.PT.
R
O
DEST.
ON/OFF
ENTER
RETURN
U
T
E
POS.
1
4
7
TEL.
BS
DEL.DEST.
M.PT. (Memory
Point) button
Displays the
memory point list.
You can set the
desired memory
point as a
destination.
Status indicator
Illuminates when the remote is
transmitting.
MENU button
Displays the main menu.
MODE button
Press this button to input numerals
using the numeric keypad. The
numerals can be input while the
status indicator is blinking.
RETURN button
Returns the navigation system to
the previous searching.
i
button
This button is not used in the
present version.
button
Switches between dual pictures
and single picture.
VOICE button
Initiates vocal instruction for next
route maneuver or repeats last
instruction.
POS. (Position) button
Returns to the current position of
your vehicle.
When this button is pressed while
the current vehicle position map is
displayed, information about
places around the current vehicle
position is displayed.
Numeric Keypad
Use these buttons after pressing
the MODE button to enter phone
numbers, address numbers or
street names containing numbers
(i.e., 42nd St.).
BS key: Deletes the character
previously input.
OK key: Executes numeral
inputting
EN
Tips:
After pressing the MODE button, press the following buttons while the status indicator is blinking : numerals
(0 to 9), BS. and OK.
Note: Due to continuous product improvement, specifications are subject to change.
43
Page 44
Reference
A.S
EL
V
O
IC
E
B
A
N
D
ENT
V.SEL
NAVI
POWER
NAVI OFF
ZOOM
DISC CHG
MUTE
A.PROCA.PROCA.PROCA.PROC
POS.
DEST.
D
IS
P
M
E
N
U
ENT
LIST
RETURN
V
O
L
.
D
N
V
O
L
U
P
ENT
A.PROC
ROUTE
LO.PT.
TUNER
POWER
DEFEAT
%
$
#
"
!
Button
No.
1
2
RUE-4131
ENTER
M
E
N
U
RETURN
V
O
I
C
E
POS.
LO.PT.
DEST.
ZOOM
OFF
ROUTE
POWER
Tilting the joystick selects items from menus and moves the map in eight directions.
Pressing the ENTER(ENT) button selects a highlighted item in the menu.
Switches between Audio and Navigation for remote controlling. Push to light. (RUE-4167 only)
1
3
4
5
(with flap lid opened)
6
7
8
9
)
12
45
78
BSOK
0
3
6
9
Description
&
(
%
$
#
"
!
RUE-4167
1
2
3
4
5
6
7
8
9
(with flap lid opened)
12
3
45
6
78
9
DEL
OK
)
0
&
(
44
3
4
5
6
Not in use.
Returns the navigation system to the previous searching.
Switches between dual pictures and single picture.
Displays the destination menu.
Returns to the current position of your vehicle.
7
When this button is pressed while the current vehicle position map is displayed, information about places
around the current vehicle position is displayed.
8
9
!
"
#
$
%
&
(
)
Changes the map magnification ratio upward or downward.
Turns the pictorial display OFF.
Turns the pictorial display ON.
Press to diaplay the information of the set POI.
The "Local POI list" screen is displayed.
Press to change the set route. "change route" screen is displayed.
Press this button for voice guidance.
Displays the main menu screen.
Input numerals.
Executes numeral inputtings and starts searching.
Erases the previous numeral in number inputtings.
Page 45
In case of difficulty
If you encounter a problem, please review the items in the following checklist. This guide will help you
isolate the problem if the system is at fault. Otherwise, make sure the system is properly connected or
consult your authorized Alpine dealer.
Symptom
Cause
Solution
EN
No operation
The present vehicle
position cannot be
measured correctly.
The measurement
error is too large.
Screen not displayed
Cannot read disc is
displayed for a certain
operation.
Unstable operation
No auto reroute
Blown fuse
Ambient temperature over 50°C
Moisture condensation
The vehicle position changed after
the ignition was switched off.
• Movement on a ferry boat
• Rotation of a parking lot turntable
• Movement by tow truck
Poor satellite configuration
Measurement is 2
dimensional
The navigation screen is off.
The disc is dirty.
The pickup lens is dirty.
The remote control batteries are
wearing out.
Auto reroute mode is not set.
Replace with a fuse of the prescribed rating.
Lower the temperature in the vehicle below 50°C, for
example by running for a while with the window open
or by using the air conditioner.
Allow enough time for the condensation to evaporate
(about 1 hour).
Drive for a while with GPS signal reception.
Move to a location where GPS satellite reception is
easy.
Press the ON (ON/OFF) button on the remote control.
Clean the disc.
Consult your Alpine dealer. (Do not use a lens cleaner
disc sold in the market.)
Replace the remote control batteries.
Select "Set up" from the main menu, then select ON
for Auto reroute. (See page 39.)
45
Page 46
Reference
If this message appears
Various messages are displayed on the monitor screen during operation. In addition to the messages
telling you the current status or providing guidance for the next operation, there are also the following
error messages. If one of these error messages is displayed, carefully follow the instructions in the
solution column.
Message
No DVD.
Please insert map DVD.
The DVD cover is open. Close it
and perform operation again.
Unable to read data.
Check if map DVD is correct.
Menu inoperable while driving.
Your home has not been
registered.
No memory points are
registered. Perform operation
again after registering a memory
point.
Unable to set additional points.
Perform operation again after
deleting unnecessary points.
No roads possible for guidance
near destination. Please refer to
map.
Route could not be found.
Cause
• The disc has been removed.
• There was no disc in the system when
the power was switched on.
• The DVD cover is open.
• A disc that the system cannot read has
been loaded.
• The disc is dirty or upside down.
• The disc cannot be read because of
condensation.
• The MENU button was pressed while
the vehicle was running.
•
A menu selection operation was carried
out while the vehicle was running.
• An attempt was made to search the
map from home with no home
registered.
• An attempt was made to search the
map from a memory point with no
memory point registered.
• An attempt was made to register more
than 200 points in memory.
• When the destination or waypoint was
specified, there was no road in the
area, so no route could be found.
• Route could not be found for some
reason.
Solution
Insert the disc.
Close the DVD cover
Insert the map disc.
Take out the disc, check if it was upside
down, clean it if necessary, then reinsert it.
Take out the disc, allow enough time for
condensation to evaporate (about 1
hour), then re-insert the disc.
Move the vehicle to a safe location, stop,
and engage the parking brake, then
carry out this operation.
Register your home, then search the
map.
Register a memory point, then search
the map.
Erase unnecessary points, then register.
Focus on a nearby major road, then
specify the destination or waypoint
again.
Try to search for route again, or set
another location as destination.
46
Page 47
EN
47
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.