Corega WLBARGMO is a MISO wireless broadband Router with IEEE802.11g
wireless access point standard. Its MIMO XR technique can improve transmit
speed and coverage area. The maximum transmit length is up to 450m and
the coverage area can be six times more than general 802.11g products. It
also has 3 antennas which can improve transmit quality. Moreover, WLBARGMO supports security settings, such as WEP, WPA/WPA2-PSK, and 802.1x.
WDS and WMM functions are also supported. With extensive functions and
superior efficiency, WLBARGMO is the best choice for users seeking for a high
quality and broad coverage area wireless broadband Router.
1.1 Package Contents
Check the listed contents thoroughly before installation. In case of discrepancy
to the list below, check with your local dealers.
- Wireless 108Mbps Broadband Router
- Power Adapter
- Detachable Antenna
- Flat UTP Cable
- Product Stand (with Mounting Screws)
- Wall Mount Kit
- Quick Installation Guide
1.2 Features
• IEEE802.11b/g standard
• Intended MIMO XR technology can improve wireless coverage up to 450m,
coverage radius is six times than general 802.11g products.(Environmental
factors may adversely affect wireless signal range.)
• Detachable Antenna Design 3 antennas , support TX-Burst technology. Can
effectivly improve transmit speed when working with corega WLCBGMO or
corega WLUSB2GO.
• Internal NAT and NAPT fuction, allowing several computers access Internet,
compatible on-line gaming, and IM software at the same time.
• Supports WMM mode, improves transmittal quailty of multimedia software.
• Supports WDS - P to MP(P to MP bridge mode )and AP Repeater (repeater
mode)
• Advanced SPI, DoS Firewall
• Chinese and English version utility
• Supports UPnP and on-line broadband applications (Such as Windows
Messenger, MSN Messenger, Yahoo Mesenger, Skype, ICQ and etc.)
WLBARGMO Manual
1
3
4
5
7
6
2
8
9
11
10
1.3 Hardware Introduction
1. Initial Button
Press this button it will reset to
default setting
2. WLAN LED (Green)
ON:Connected
3. Power LED (Green)
Indicate power status
4.Status LED (Red)
Blink:Working normal
ON:Firmware upgrade
5. WAN LED (Green)
ON:Connected
Blink:Transmitting or receiving
data
6. Speed LED (Green)
ON:100Mbps
Off:10Mbps
7. Link LED (Green)
ON:Connected
Blink:Transmitting or
receiving data
8. Detachable Antenna
Connector
9. WAN port
Connected with modem
10. LAN ports(1-4)
Connected with PC
11. AC IN Socket
Connect with power adapter
45
WAN
LAN
Product Installation
WLBARGMO Manual
2
2.1 Hardware Installation
Following the steps below to set up WLBARGMO and the connection.
(1) Insert the cable connector into the Network Adapter embeded in PC, and
insert the other side into one of LAN ports (1~4) of the Router.
(2) Insert the connect into the WAN port of the Router and insert the other side
into the modem.
(3) Connect the Power Adapter, and plug in the AC power.
2.2 Installation Procedure
To ensure successful installation, following the below steps after confirming all installation data and/or equipment.
Install the hardware -> PC setting -> Open the browser (such as IE 6.0),
and type [192.168.1.1] in the browser’s address bar, and press enter. ->
User name: Root, leave Password empty, and press Submit. ->Select [Quick
Installation Setting] for quick installation->Setting the Wirless Security->Use
PC with compatible wireless card for wireless connection.
PC Setting
WLBARGMO Manual
3
3.1 TCP/IP Configuration
The following steps and screenshots maybe dissimilar in different operating systems. This manual takes Windows XP/2000, 95/98/ME, and Mac O/S as
examples:
3.1.1 Windows XP O/S
(1) Enter [Control Panel] -> click [Network Connection] -> right click and select
[Open].
(2) Click [Local Area Connection] and right click and select [Properties].
(3) Unselect all three options in the [Local Area Network LAN Setting].
(4) Press [OK] in the [Internet Options].
3.2.2 Mac O/S
(1) Open Internet Explorer (IE 5.0) Go to [Edit] in the menu bar, select [Internet
Explorer Preferences].
(2) Select [Proxies] options in [Network] on the left-side configuration items.
(3) Do not select [Web Proxy], press [OK].
1415
Network Configuration
4
4.1 Quick Network Configuration
Basic configuration is required before connection your computer to the internet via WLBARGMO. The connection methods may be differed by your contract
to the ISP. Please reconfirm your connection conditions with your ISP prior to
configure this router. The configuration procedures are as follow:
*Note: Anti-virus or Firewall software may prevent this router from being set-up
properly. Please close such software through out the setting of WLBARGMO.
(1) Open the Web browser (Internet Explorer 6.0). If you use dial-up network
such as PPPoE, and are using Windows 2000/98/ME O/S. The [Dial-up
Network] window will pop-up; do not connect to the Internet right now,
and close the window.
(2) Type [192.168.1.1] in the browser’s address bar, press [Enter].
*Note: [192.168.1.1] is the IP address for configuring CG-WALBARGMO, and is not
corega’s company public internet address. After you have completed the
configuration, connect to [http://www.corega-asia.com] for testing the
connection.
WLBARGMO Manual
(3) When log-in screen is appeared, type [root] for the username, and leave
empty for the password. Press [Submit].
(4) Please select the language. e.g.) English. ->Select your region. e.g.)
Singapore.=>Click [Apply].
Loading...
+ 39 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.