Allied Telesis AT-VIEW PLUS 2.4 User Manual

Download

AT-V

EVICE MANAGEMENT GUIDE

IEW PLUS 2.4

PN 613-50507-00 Rev D Page 1 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Microsoft is a registered trademark of Microsoft Corporation. Netscape Navigator is a registered trademark of Netscape Communications Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners.

Allied Telesis K. K. reserves the right to make changes in specifications and other information contained in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis K.K. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis K. K. has been advised of, known, or should have known, the possibility of such damages.

PN 613-50507-00 Rev D Page 2 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

TABLE OF CONTENTS

Basic Operations................................................................................................................ 10

Common operations on the main window....................................................................... 11

Menu for stacked devices ............................................................................................... 11

Port selection dialog box................................................................................................. 13

Port status colors............................................................................................................ 13

LED status ...................................................................................................................... 13

Utilization ........................................................................................................................ 14

AT-8000 Series .................................................................................................................. 15

Main Window .................................................................................................................. 15

Agent Menu .................................................................................................................... 22

Bridge Menu ................................................................................................................... 23

RMON Menu................................................................................................................... 23

Port Menu ....................................................................................................................... 24

Stacking Menu................................................................................................................ 26

Expansion Module Notes................................................................................................ 26

AT-8124 ............................................................................................................................. 28

Main Window .................................................................................................................. 28

Agent Menu .................................................................................................................... 29

Bridge Menu ................................................................................................................... 29

RMON Menu................................................................................................................... 30

Port Menu ....................................................................................................................... 30

AT-8124XL (V2) ................................................................................................................. 32

Main Window .................................................................................................................. 32

Agent Menu .................................................................................................................... 33

Bridge Menu ................................................................................................................... 33

RMON Menu................................................................................................................... 34

Port Menu ....................................................................................................................... 34

AT-8200XL Series.............................................................................................................. 36

Main Window .................................................................................................................. 36

Agent Menu .................................................................................................................... 37

Bridge Menu ................................................................................................................... 39

RMON Menu................................................................................................................... 40

Port Menu ....................................................................................................................... 40

Expansion Module Notes................................................................................................ 42

AT-8324 ............................................................................................................................. 43

Main Window .................................................................................................................. 43

Agent Menu .................................................................................................................... 44

Bridge Menu ................................................................................................................... 45

RMON Menu................................................................................................................... 45

Port Menu ....................................................................................................................... 46

Stacking Menu................................................................................................................ 48

AT-8324SX......................................................................................................................... 49

Main Window .................................................................................................................. 50

PN 613-50507-00 Rev D Page 3 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Agent Menu .................................................................................................................... 51

Bridge Menu ................................................................................................................... 52

RMON Menu................................................................................................................... 52

Port Menu ....................................................................................................................... 53

Stacking Menu................................................................................................................ 54

AT-8300GB Series ............................................................................................................. 55

Main Window .................................................................................................................. 56

Agent Menu .................................................................................................................... 58

Bridge Menu ................................................................................................................... 59

RMON Menu................................................................................................................... 60

Port Menu ....................................................................................................................... 60

Stacking Menu................................................................................................................ 61

AT-8400 ............................................................................................................................. 63

Main Window .................................................................................................................. 64

Agent Menu .................................................................................................................... 65

Bridge Menu ................................................................................................................... 66

RMON Menu................................................................................................................... 67

Port Menu ....................................................................................................................... 68

Stacking Menu................................................................................................................ 69

AT-8400 Line Cards ........................................................................................................... 70

AT-8411.......................................................................................................................... 70

AT-8412.......................................................................................................................... 71

AT-8413.......................................................................................................................... 72

AT-8414.......................................................................................................................... 73

AT-9006 Family.................................................................................................................. 74

Main Window .................................................................................................................. 74

Agent Menu .................................................................................................................... 75

Bridge Menu ................................................................................................................... 76

RMON Menu................................................................................................................... 76

VLAN Menu .................................................................................................................... 77

Port Menu ....................................................................................................................... 77

AT-9410GB ........................................................................................................................ 79

Main Window .................................................................................................................. 79

Agent Menu .................................................................................................................... 80

Bridge Menu ................................................................................................................... 81

RMON Menu................................................................................................................... 81

Port Menu ....................................................................................................................... 82

AT-FH800u......................................................................................................................... 84

Main Window .................................................................................................................. 84

Agent Menu .................................................................................................................... 85

Hub Menu ....................................................................................................................... 86

Module Menu.................................................................................................................. 86

RMON Menu................................................................................................................... 86

Port Menu ....................................................................................................................... 87

AT-AR200E ........................................................................................................................ 88

Main Window .................................................................................................................. 88

PN 613-50507-00 Rev D Page 4 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Agent Menu .................................................................................................................... 90

Routing Menu ................................................................................................................. 90

Bridge Menu ................................................................................................................... 92

ADSL Menu .................................................................................................................... 92

ATM Menu ...................................................................................................................... 93

PPP Menu ...................................................................................................................... 96

Port Menu ....................................................................................................................... 99

AT-AR300 and AT-AR300L.............................................................................................. 101

Main Window ................................................................................................................ 101

Agent Menu .................................................................................................................. 102

Routing Menu ............................................................................................................... 103

Bridge Menu ................................................................................................................. 103

Frame Relay Menu ....................................................................................................... 103

Call List Menu............................................................................................................... 104

Port Menu ..................................................................................................................... 104

AT-AR320 ........................................................................................................................ 105

Main Window ................................................................................................................ 105

Agent Menu .................................................................................................................. 106

Routing Menu ............................................................................................................... 106

Bridge Menu ................................................................................................................. 106

Port Menu ..................................................................................................................... 107

AT-AR350 ........................................................................................................................ 108

Main Window ................................................................................................................ 108

Agent Menu .................................................................................................................. 109

Routing Menu ............................................................................................................... 109

Bridge Menu ................................................................................................................. 109

Port Menu ..................................................................................................................... 110

AT-AR370 ........................................................................................................................ 111

Main Window ................................................................................................................ 111

Agent Menu .................................................................................................................. 112

Routing Menu ............................................................................................................... 112

Bridge Menu ................................................................................................................. 113

Frame Relay Menu ....................................................................................................... 113

Call List Menu............................................................................................................... 114

Port Menu ..................................................................................................................... 114

AT-AR410 ........................................................................................................................ 115

Main Window ................................................................................................................ 115

Agent Menu .................................................................................................................. 116

Routing Menu ............................................................................................................... 116

Bridge Menu ................................................................................................................. 117

Frame Relay Menu ....................................................................................................... 117

Call List Menu............................................................................................................... 117

Port Menu ..................................................................................................................... 117

AT-AR450S ...................................................................................................................... 119

Main Window ................................................................................................................ 119

Agent Menu .................................................................................................................. 120

PN 613-50507-00 Rev D Page 5 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Routing Menu ............................................................................................................... 120

Bridge Menu ................................................................................................................. 121

Port Menu ..................................................................................................................... 121

AT-AR720 ........................................................................................................................ 122

Main Window ................................................................................................................ 122

Agent Menu .................................................................................................................. 123

Routing Menu ............................................................................................................... 123

Bridge Menu ................................................................................................................. 124

Frame Relay Menu ....................................................................................................... 124

Call List Menu............................................................................................................... 124

Port Menu ..................................................................................................................... 124

AT-AR725 ........................................................................................................................ 126

Main Window ................................................................................................................ 126

Agent Menu .................................................................................................................. 128

Routing Menu ............................................................................................................... 128

Bridge Menu ................................................................................................................. 129

Frame Relay Menu ....................................................................................................... 129

Call List Menu............................................................................................................... 129

Port Menu ..................................................................................................................... 129

AT-AR740 ........................................................................................................................ 131

Main Window ................................................................................................................ 131

Agent Menu .................................................................................................................. 133

Routing Menu ............................................................................................................... 133

Bridge Menu ................................................................................................................. 134

Frame Relay Menu ....................................................................................................... 134

Call List Menu............................................................................................................... 134

Port Menu ..................................................................................................................... 135

AT-AR745 ........................................................................................................................ 136

Main Window ................................................................................................................ 136

Agent Menu .................................................................................................................. 138

Routing Menu ............................................................................................................... 138

Bridge Menu ................................................................................................................. 139

Frame Relay Menu ....................................................................................................... 139

Call List Menu............................................................................................................... 139

Port Menu ..................................................................................................................... 140

AT-8724XL ....................................................................................................................... 141

Main Window ................................................................................................................ 141

Agent Menu .................................................................................................................. 142

Routing Menu ............................................................................................................... 143

Bridge Menu ................................................................................................................. 143

Port Menu ..................................................................................................................... 144

AT-8748XL ....................................................................................................................... 145

Main Window ................................................................................................................ 145

Agent Menu .................................................................................................................. 146

Routing Menu ............................................................................................................... 147

Bridge Menu ................................................................................................................. 147

PN 613-50507-00 Rev D Page 6 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Port Menu ..................................................................................................................... 148

AT-8824 ........................................................................................................................... 149

Main Window ................................................................................................................ 149

Agent Menu .................................................................................................................. 150

Routing Menu ............................................................................................................... 151

Bridge Menu ................................................................................................................. 151

Port Menu ..................................................................................................................... 152

AT-8848 ........................................................................................................................... 153

Main Window ................................................................................................................ 153

Agent Menu .................................................................................................................. 154

Routing Menu ............................................................................................................... 155

Bridge Menu ................................................................................................................. 155

Port Menu ..................................................................................................................... 156

AT-8948 ........................................................................................................................... 157

Main Window ................................................................................................................ 157

Agent Menu .................................................................................................................. 158

Routing Menu ............................................................................................................... 159

Bridge Menu ................................................................................................................. 159

Port Menu ..................................................................................................................... 160

Rapier 16F/MT and 16F/SC ............................................................................................. 161

Main Window ................................................................................................................ 161

Agent Menu .................................................................................................................. 163

Routing Menu ............................................................................................................... 163

Bridge Menu ................................................................................................................. 164

Frame Relay Menu ....................................................................................................... 164

Call List Menu............................................................................................................... 165

Port Menu ..................................................................................................................... 165

Rapier 24 and 24i............................................................................................................. 166

Main Window ................................................................................................................ 166

Agent Menu .................................................................................................................. 168

Routing Menu ............................................................................................................... 168

Bridge Menu ................................................................................................................. 169

Frame Relay Menu ....................................................................................................... 169

Call List Menu............................................................................................................... 170

Port Menu ..................................................................................................................... 170

Rapier 48 and 48i............................................................................................................. 171

Main Window ................................................................................................................ 171

Agent Menu .................................................................................................................. 173

Routing Menu ............................................................................................................... 173

Bridge Menu ................................................................................................................. 174

Port Menu ..................................................................................................................... 174

Rapier G6......................................................................................................................... 176

Main Window ................................................................................................................ 176

Agent Menu .................................................................................................................. 177

Routing Menu ............................................................................................................... 178

Bridge Menu ................................................................................................................. 178

PN 613-50507-00 Rev D Page 7 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Port Menu ..................................................................................................................... 179

Rapier G6F-LX/SC, G6F-SX/SC, G6F-SX/MT-RJ............................................................ 180

Main Window ................................................................................................................ 180

Agent Menu .................................................................................................................. 182

Routing Menu ............................................................................................................... 183

Bridge Menu ................................................................................................................. 183

Port Menu ..................................................................................................................... 184

SwitchBlade 4004 ............................................................................................................ 185

Main Window ................................................................................................................ 186

Agent Menu .................................................................................................................. 187

Routing Menu ............................................................................................................... 188

Bridge Menu ................................................................................................................. 188

Port Menu ..................................................................................................................... 189

SwitchBlade 4008 ............................................................................................................ 190

Main Window ................................................................................................................ 190

Agent Menu .................................................................................................................. 192

Routing Menu ............................................................................................................... 193

Bridge Menu ................................................................................................................. 193

Port Menu ..................................................................................................................... 194

SwitchBlade Line Cards ................................................................................................... 195

AT-9812T ......................................................................................................................... 198

Main Window ................................................................................................................ 198

Agent Menu .................................................................................................................. 199

Routing Menu ............................................................................................................... 200

Bridge Menu ................................................................................................................. 200

Port Menu ..................................................................................................................... 201

AT-9816GB ...................................................................................................................... 202

Main Window ................................................................................................................ 202

Agent Menu .................................................................................................................. 203

Routing Menu ............................................................................................................... 204

Bridge Menu ................................................................................................................. 204

Port Menu ..................................................................................................................... 205

AT-MCF06 Family ............................................................................................................ 206

Main Window ................................................................................................................ 206

Agent Menu .................................................................................................................. 207

Status Menu ................................................................................................................. 208

AT-MCF12 Family ............................................................................................................ 209

Main Window ................................................................................................................ 209

Agent Menu .................................................................................................................. 210

Status Menu ................................................................................................................. 211

AT-MCF106 Family .......................................................................................................... 212

Main Window ................................................................................................................ 212

Agent Menu .................................................................................................................. 213

Status Menu ................................................................................................................. 214

AT-MCF112 Family .......................................................................................................... 215

Main Window ................................................................................................................ 215

PN 613-50507-00 Rev D Page 8 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Agent Menu .................................................................................................................. 216

Status Menu ................................................................................................................. 217

AT-MPB3000.................................................................................................................... 218

Main Window ................................................................................................................ 218

Agent Menu .................................................................................................................. 220

Status Menu ................................................................................................................. 220

AT-MPB3000 Modules ..................................................................................................... 221

AT-MCM100 Modules................................................................................................... 221

AT-MCM110 Modules................................................................................................... 222

AT-MCM1000S Modules .............................................................................................. 223

AT-MCM1000T Modules............................................................................................... 224

PowerBlade...................................................................................................................... 225

Main Window ................................................................................................................ 225

Agent Menu .................................................................................................................. 226

Status Menu ................................................................................................................. 227

PowerBlade Modules ....................................................................................................... 228

AT-PB10 Series Media Converter Modules .................................................................. 228

AT-PB100 Series Media Converter Modules ................................................................ 229

AT-PB200 Series Switch Modules................................................................................ 230

AT-PB300 Series Media Converter Modules ................................................................ 231

AT-PB1000 Series Media Converter Modules .............................................................. 232

AT-RG213 ........................................................................................................................ 233

Main Window ................................................................................................................ 233

Agent Menu .................................................................................................................. 234

RTC Menu .................................................................................................................... 234

Port Menu ..................................................................................................................... 235

AT-RG600 Series............................................................................................................. 237

Main Window ................................................................................................................ 237

Agent Menu .................................................................................................................. 239

Bridge Menu ................................................................................................................. 239

IGMP Menu .................................................................................................................. 240

VoIP Menu.................................................................................................................... 241

Port Menu ..................................................................................................................... 242

Port Interface Cards ......................................................................................................... 244

AT-AR020..................................................................................................................... 244

AT-AR021..................................................................................................................... 244

AT-AR022..................................................................................................................... 245

AT-AR023..................................................................................................................... 245

AT-AR024..................................................................................................................... 245

AT-AR026..................................................................................................................... 245

AT-AR027..................................................................................................................... 246

Network Service Modules................................................................................................. 247

Uplink Modules................................................................................................................. 249

Layer 2 Switches Uplink Modules................................................................................. 249

Advanced Layer 2 Switches and Layer 3 Switches Uplink Modules............................. 252

PN 613-50507-00 Rev D Page 9 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

This document describes the operations and menus specific to particular Allied Telesyn models of managed devices. For module-independent information, refer to the AT-View Plus Device Manager User's Guide.

Basic Operations

AT-View Plus Device Manager's main window shows the main panel of the target device. It has both common and device-specific menus on its menu bar.

You can perform operations on the agent by doing a right click on the main panel or by selecting a menu item from the menu bar. Ports and LEDs on the main panel indicate the status of the port, system and traffic.

Topics:

• Common operations on the main window

• Menu for stacked devices

• Port selection dialog box

• Port status colors

• LED status

• Utilization

PN 613-50507-00 Rev D Page 10 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Common operations on the main window

Right clicking on a port

Port

Right clicking on a port opens a pull-down menu specific to the device. Selecting a menu item opens another window and lets you view and edit MIB information related to the port. You can also access the same menu from the menu bar.

RS-232 Terminal Port

Right clicking on an RS-232 port opens a pull-down menu and lets you choose how to log into the agent. Depending on the managed device, choose Telnet or WEB Browser.

Reset Button

Right clicking on a reset button opens a pull-down menu with an option that allows you to reset the device. (Not available on some devices.)

Menu for stacked devices

If the target is a stacked device, some menus have extra subitems to specify a single device in the stack.

PN 613-50507-00 Rev D Page 11 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Module submenu

PN 613-50507-00 Rev D Page 12 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Port selection dialog box

When you select a menu item acting on ports, a dialog box opens to let you select ports. Check the target ports and click OK.

Note - If you select multiple ports, it may take some time for data to be displayed.

Select Port dialog box

Port status colors

Port status is shown by its color. Port speed is also displayed in the port image.

• Link Up: Green

• Disabled: Red (the port is disabled by an administrator)

• Partitioned/Blocking: Yellow

• Others: Default colour (usually black)

LED status

In AT-View Plus Device Manager, LEDs do not blink. The meanings of LEDs differ between devices.

PN 613-50507-00 Rev D Page 13 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Utilization

Utilization is calculated by the following formula.

# of frames x (96 + 64) + octets x 8 Utilization (%) = ------------------------------------------- x 100 Port speed (bps) x Sampling Interval(sec)

Basic Operations

PN 613-50507-00 Rev D Page 14 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8000 Series

This section describes AT-View Plus Device Manager menus and operations specific to the AT8000 Series (excluding the AT-8026T).

Topics:

• Main Window

• Agent Menu

• Bridge Menu

• RMON Menu

• Port Menu

• Stacking Menu

• Expansion Module Notes

Main Window

AT-8012M

PN 613-50507-00 Rev D Page 15 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8016F/MT

AT-8016F/SC

PN 613-50507-00 Rev D Page 16 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8016F/ST

AT-8024

PN 613-50507-00 Rev D Page 17 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8024GB

AT-8024M

PN 613-50507-00 Rev D Page 18 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8026FC

AT-8026T

PN 613-50507-00 Rev D Page 19 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8088/MT

AT-8088/SC

PN 613-50507-00 Rev D Page 20 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Device Manager LEDs for AT-8000 Series

LED State Description

PWR Green The switch is receiving power.

MASTER Orange

The switch is the master switch of an enhanced stack.

Gray

DUPLEX Green

Orange

The switch is a slave switch or is not a member of an enhanced stack.

The port is operating in full-duplex mode.

The port is operating in half-duplex mode.

Note - Please refer to Uplink Modules for the operations and behavior of the expansion modules

installed on these devices.

Note - The current firmware version does not allow AT-View Plus Device Manager to support the

RPS LED.

Note - When connecting to a slave switch, AT-View Plus Device Manager does not automatically

replace the master switch image in the main window with the slave switch image. To view the slave switch image, click on the Refresh option under the Agent menu.

Note - AT-View Plus Device Manager will detect a loss of connection between an AT-8024GB and

an AT-9410GB when the uplink port on both devices are set to the same speed and mode.

Note - Connection between an AT-8024GB and an AT-8324 can only be established if the uplink

ports on both devices are configured to auto-negotiate.

Note - When a port's Port Speed and Mode parameter is set to 'auto sense' and the port is connected

to a full duplex port on another device, its corresponding Duplex LED on the device image turns orange instead of green.

Note - The Port State parameter of ports that are disabled while 'Active Protocol Version' is set to

'STP' will be set to 'blocking' once 'Spanning Tree Status' is set to 'enabled'. As a result, the port images for the disabled ports will turn yellow.

Note - Setting the 'Active Protocol Version' to 'RSTP' and 'Spanning Tree Status' to 'enabled' will set

the Port State parameter of inactive ports to 'blocking'. As a result, port images for inactive ports will turn yellow.

Note - Port images for active and inactive ports that are disabled while 'Active Protocol version' is

set to 'RSTP' will turn to green (active) and black (inactive) once 'Spanning Tree Status' is set to 'enabled'.

PN 613-50507-00 Rev D Page 21 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - Port images of inactive ports that are disabled while 'Active Protocol Version' is set to 'RSTP'

will turn to yellow after 'Spanning Tree Status' is set to 'enabled' the second time.

Agent Menu

From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet.

System Info

Displays basic system information, including system name, location, contact and description.

Note - Attempting to enter more than 39 characters for the System Contact, System Name,

and System Location parameters may result in a timeout error. If a timeout error occurs, the switch will have to be restarted causing these parameters to be cleared of any value.

Note - Attempting to set the System Contact, System Name, and System Location parameters

to NULL will result in a general error. However, the parameters will still be temporarily set to NULL. Once the switch is restarted, the original values will be restored.

Firmware Info

Displays firmware version.

Network Info

Displays network-related information such as the addresses of the default gateway and the agents.

Note - The current firmware version does not allow the Default Domain Name and the DNS

Server parameters to be configured.

Manager Address Info

Displays the IP address of the management station.

Device Info

Displays general information about the switch.

MAC Address Table

Displays a list of static MAC addresses configured on the switch.

Note - MAC Address Table entries created through a local or telnet management session will

not be visible to AT-View Plus Device Manager until the device is restarted.

Note - The current firmware version does not allow the Port Number parameter to be

configured. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: gen Error".

PN 613-50507-00 Rev D Page 22 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Reset

Resets the switch.

Telnet

Starts a Telnet connection to the switch.

WEB Browser

Connects to the switch's HTTP server.

Bridge Menu

From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status.

Forwarding Database

Displays the Forwarding Database table.

Discard/Aging Time Info

Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.

Note - The current firmware version does not allow values greater than 1000000 for the

Aging Time parameter.

Spanning Tree Info

Displays spanning tree parameters such as priority and cost.

Statistics

Displays statistics about frames received/transmitted on the switch port.

RMON Menu

From the RMON menu you can view and edit the RMON MIB.

Statistics

Displays traffic statistics in the network segment attached to each port.

History Control Table

Displays the RMON History table.

Note - The current firmware version does not support the "historyControlTable" MIB object

of RFC1757. As a result, AT-View Plus Device Manager displays the error message "Failed to get MIB data." when the History Control Table option is selected from the RMON menu.

PN 613-50507-00 Rev D Page 23 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Alarm Table

Displays the RMON Alarm table.

Event Table

Displays the RMON Event table.

Event Log

Displays the RMON Event log.

Port Menu

From the Port menu, you can view and edit MIB information about the port.

Utilization

Displays the port's utilization information.

Interface Info

Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.

Note - Valid MIB Set values for the Administration Status parameter are 'up' and 'down'.

Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Error Statistics

Displays error statistics.

Detail Info

Displays detailed port information such as duplex mode.

Note - Setting the Port Reset parameter to 'reset' will not reset the port's attributes.

Note - Valid MIB Set values for the Port Flow Control parameter are 'disable', 'transmit-

only', 'receive-only', and 'transmit-and-receive'. However, the current firmware version does not allow this parameter to be set to 'transmit-only' and 'receive-only' for the following ports:

• Expansion module ports

• GBIC ports on the AT-8024GB

• Fiber optic ports on the AT-8026FC

Note - For AT-8024GB devices, the current firmware version does not allow the Port Speed

and Mode parameter of the GBIC ports to bet set to '1Gbps half-duplex'.

PN 613-50507-00 Rev D Page 24 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - Valid MIB Set Values for the Port State parameter are 'enabled' and 'disabled'.

Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Note - The current firmware version does not allow the Port Name parameter to be

configured. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: noSuchName".

Spanning Tree Info

Displays the port's spanning tree parameters.

Note - Setting a port's Port parameter to 'disabled' does not automatically set the Port State

parameter under Detail Info to 'disabled'. As a result, the port's image may not turn red as expected.

Enable

Enables the port.

Note - Under the Sun Solaris platform, the AT-View Plus Device Manager application may

terminate abnormally if multiple ports have been selected and each dialog box with the message "May I set 'atiswitchPortState.n' to up" is clicked one after the other.

Disable

Disables the port.

Note - Under the Sun Solaris platform, the AT-View Plus Device Manager application may

terminate abnormally if multiple ports have been selected and each dialog box with the message "May I set 'atiswitchPortState.n' to down" is clicked one after the other.

Port Mirroring

Displays port mirroring parameters and allows configuration of port mirroring state, source, and destination.

Note - Valid MIB Set values for the Mirroring Destination Port parameter should range from

0 to 24. However, the current firmware version allows the user to enter values up to 65535. Attempting to enter values greater than 65535 will cause the new value to be converted to its equivalent wrap-around value; i.e., 65536 will become 0, 65537 will become 1, and so on.

Note - Valid MIB Set values for the Port Mirroring Status parameter are 'receive', 'transmit',

and 'both'. However, the current firmware version does not allow this parameter to be set to 'receive' and 'transmit'. Attempting to do so will result in the error message: "The error occurred with 'Set' operation. Error: bad value".

PN 613-50507-00 Rev D Page 25 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Stacking Menu

From the Stacking menu, you can perform enhanced stacking from any AT-8000 Series master switch.

Stacking Info

Displays information about the switch's mode. This is also the menu where you can perform enhanced stacking.

Expansion Module Notes

• AT-View Plus Device Manager cannot distinguish between the AT-A45/xx, AT-A47, and

AT-STACKM expansion modules. All are displayed with the same GIF image.

• When both the AT-A45 and AT-A46 expansion modules are present on a device, the AT-

A45 port image may show up as green and its Port Speed parameter may reflect the value "1 Gbps" even if there is no connection established on the port. To reflect the correct port image color and port speed, restart the device. This applies to the following devices:

 AT-8016F/xx  AT-8024M  AT-8088/xx

• Connection cannot be established on the AT-A46 expansion module port if the Port Speed

and Mode parameter is set to "auto 1Gbps".

• When the Port Speed and Mode parameter of the AT-A46 expansion module port is set to

"auto 10/100Mbps" and the port is connected to a 10/100Mbps full-duplex port on another device, its corresponding Duplex LED on the device image turns orange instead of green.

• The Spanning Tree Protocol (STP) does not work for the AT-A46 expansion module when it

is installed on an AT-8016F/ST device. As a result, the Port State parameter of the AT-A46 expansion module port will never be set to 'blocking' and the port image will never turn yellow.

• Connection between an AT-A47 expansion module port that is configured to operate at

1Gbps full duplex and a port on another device can only be established if the port on the other device is configured to auto-negotiate.

• For the AT-A47 expansion module, AT-View Plus Device Manager will only display the

AT-A45/AT-A47/AT-STACKM shared GIF image if a GBIC module is present in the GBIC slot.

PN 613-50507-00 Rev D Page 26 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

• By default, the Port Speed and Mode parameter of the AT-A47 expansion module port is set

to 'auto sense'. From this mode, the Port Speed and Mode can only be changed to '1Gbps fullduplex'. However, once set to '1Gbps full-duplex', it can no longer be set to 'auto sense'.

• The Port Speed and Mode parameter of the AT-STACKM expansion module cannot be

modified. It is fixed at '1Gbps full-duplex'.

AT-8000 Series

PN 613-50507-00 Rev D Page 27 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8124

This section describes AT-View Plus Device Manager menus and operations specific to the AT8124 switch.

Topics:

• Main Window

• Agent Menu

• Bridge Menu

• RMON Menu

• Port Menu

Main Window

AT-8124

Device Manager LEDs for AT-8124

LED State Description

PWR Green The switch is receiving power.

DUPLEX Green

Gray

PN 613-50507-00 Rev D Page 28 of 253

The port is operating in full-duplex mode.

The port is operating in half-duplex mode.

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Agent Menu

From the Agent menu, you can view and edit the system information for the device or log into the CLI using telnet.

System Info

Displays basic system information, including system name, location, contact and description.

Network Info

Displays network-related information such as the device's IP address, and the default gateway address.

Firmware Info

Displays the version of the software running on the managed device.

Manager Address Info

Displays the management station's IP address.

Reset

Resets the switch.

Hot Reset

Performs a software reset. This takes less time than a Cold Reset.

Cold Reset

Performs a hardware reset. This takes more time than a Hot Reset.

Telnet

Connects to the switch's Telnet service.

Bridge Menu

From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status.

Forwarding Database

Displays the Forwarding Database table.

Discard/Aging Time Info

Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.

Spanning Tree Info

Displays spanning tree parameters such as priority and cost.

PN 613-50507-00 Rev D Page 29 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Statistics

Displays statistics about frames received/transmitted on the switch port.

RMON Menu

From the RMON menu you can view and edit the RMON MIB.

Note - Since there may be a large quantity of RMON data, it may take some time for the information

to appear.

Statistics

Displays traffic statistics about the network segment attached to each port.

History Control Table

Displays the RMON History table.

Alarm Table

Displays the RMON Alarm table.

Event Table

Displays the RMON Event table.

Event Log

Displays the RMON Event log.

Port Menu

From the Port menu, you can view and edit MIB information about the port.

Utilization

Displays the port's utilization information.

Interface Info

Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.

Detail Info

Displays port traffic statistics such as the number of frames received/transmitted on the port.

Error Statistics

Displays error information.

Detail Status

Displays detailed port information such as duplex mode.

PN 613-50507-00 Rev D Page 30 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Spanning Tree Info

Displays the port's spanning tree parameters.

Enable

Enables the port.

Disable

Disables the port.

AT-8124

PN 613-50507-00 Rev D Page 31 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8124XL (V2)

This section describes AT-View Plus Device Manager menus and operations specific to the AT8124XL (V2) switch.

Topics:

• Main Window

• Agent Menu

• Bridge Menu

• RMON Menu

• Port Menu

Main Window

AT-8124XL (V2)

Device Manager LEDs for AT-8124XL (V2)

LED State Description

PWR Green The switch is receiving power.

DUPLEX Green

Orange

PN 613-50507-00 Rev D Page 32 of 253

The port is operating in full-duplex mode.

The port is operating in half-duplex mode.

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Agent Menu

From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet.

System Info

Displays basic system information, including system name, location, contact and description.

Note - AT-View Plus Device Manager allows the user to enter up to 255 characters for the

System Contact, System Name, and System Location parameters but truncates them to 64 characters. NULL values are not accepted.

Firmware Info

Displays firmware version.

Network Info

Displays network-related information such as the addresses of the default gateway and the agents.

DHCP Info

Displays DHCP information including the DHCP System Group and DHCP Timer Group.

Manager Address Info

Displays the IP address of the management station.

Reset

Resets the switch.

Telnet

Starts a Telnet connection to the switch.

WEB Browser

Connects to the switch's HTTP server.

Bridge Menu

From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status.

Forwarding Database

Displays the Forwarding Database table.

Discard/Aging Time Info

Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.

PN 613-50507-00 Rev D Page 33 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Spanning Tree Info

Displays spanning tree parameters such as priority and cost.

Statistics

Displays statistics about frames received/transmitted on the switch's ports.

RMON Menu

From the RMON menu you can view and edit the RMON MIB.

Statistics

Displays traffic statistics in the network segment attached to each port.

History Control Table

Displays the RMON History table.

Alarm Table

Displays the RMON Alarm table.

Event Table

Displays the RMON Event table.

Event Log

Displays the RMON Event log.

Port Menu

From the Port menu, you can view and edit MIB information about the port.

Utilization

Displays the port's utilization information.

Interface Info

Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.

Note - Valid MIB Set values for the Administration Status parameter are 'up' and 'down'. All

other values are ignored.

Detail Info

Displays detailed port information such as duplex mode.

Note - Enabling/Disabling the Port STP Configuration parameter for one port

enables/disables STP for all ports.

PN 613-50507-00 Rev D Page 34 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - Attempting to modify the Port Speed and Mode parameter from 'auto sense' to '1Gbps

half-duplex' or '1Gbps full-duplex' will result in the following:

• An error message: "The error occurred with 'Set' operation. Error: gen Error"

• Port Speed and Mode parameter value changing to '100Mbps half-duplex'

Note - The current firmware version does not allow the Port Bridge ID parameter to be

configured. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Note - When a port is set to 'auto sense' and is connected to a half duplex port on another

device, its corresponding Duplex LED on the device image turns green instead of orange.

Note - The current firmware version does not allow the Port Back Pressure parameter to be

configured. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: time out occurred."

Note - The Port Transmit Pacing Configuration parameter is not applicable to the AT-

8124XL (V2).

Note - The current firmware version does not allow the Port VLAN Tag Priority and the Port

QoS Priority parameters to be configured. Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Note - Valid MIB Set values for the Port State parameter are 'enabled' and 'disabled'.

Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value.".

Spanning Tree Info

Displays the port's spanning tree parameters.

Enable

Enables the port.

Disable

Disables the port.

Port Mirroring

Displays port mirroring parameters and allows configuration of port mirroring state, source, and destination.

IGMP Snooping

Displays the current state of IGMP Snooping and allows reconfiguration.

AT-8124XL (V2)

PN 613-50507-00 Rev D Page 35 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8200XL Series

This section describes AT-View Plus Device Manager menus and operations specific to the AT8216FXL/SC and AT-8224XL switches.

Topics:

• Main Window

• Agent Menu

• Bridge Menu

• RMON Menu

• Port Menu

• Expansion Module Notes

Main Window

AT-8216FXL/SC

PN 613-50507-00 Rev D Page 36 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8224XL

Device Manager LEDs for AT-8200XL Series

LED State Description

PWR Green The switch is receiving power.

RPS

DUPLEX Green

Green

Gray

Orange

An optional redundant power supply is connected to the switch.

There is no redundant power supply connected to the switch.

The port is operating at full-duplex mode.

The port is operating at half-duplex mode.

Note - Please refer to Uplink Modules for the operations and behavior of the expansion modules

installed on these devices.

Agent Menu

From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet.

System Info

Displays basic system information, including system name, location, contact and description.

PN 613-50507-00 Rev D Page 37 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - The current firmware version allows the user to enter up to 64 characters for the

System Contact and the System Location parameters and up to 20 characters for the System Name parameter.

Note - The current firmware version appends a period '.' and the value of the Default Domain

Name parameter to the value of the System Name parameter.

Firmware Info

Displays the firmware version of the switch.

Network Info

Displays network-related information such as the addresses of the default gateway and the agents.

Manager Address Info

Displays the IP address of the management station.

Device Info

Displays general information about the switch.

Note - The Security Action parameter has a fixed value of 'do nothing' and cannot be

modified.

Note - The Security Configuration parameter has a fixed value of 'disabled' and cannot be

modified.

Note - Valid MIB Set values for the HOL Configuration and Logging Configuration

parameters are 'on' and 'off'. Attempting to set these parameters to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value".

Note - Valid MIB Set values for the QoS Configuration parameter are:

• mode 1

• mode 2

• mode 3

• mode 4

• mode 5

• mode 6

• mode 7

• mode 8

Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value".

PN 613-50507-00 Rev D Page 38 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

DHCP Info

Displays the DHCP information about the switch.

Diagnostics

Displays the operating status of the switch's components such as power supply and system fans.

Note - The current firmware version returns 'non-supported' for the following parameters:

• Fan Speed 3

• 3.3V Power

• 2.5Va Power

• 2.5Vb Power

• 2V Power

• CPU Temperature

Reset

Resets the switch.

Console Settings

Displays the current settings of the console.

Telnet

Starts a Telnet connection to the switch.

WEB Browser

Connects to the switch's HTTP server.

Note - The current firmware version is unable to display the AT-8216FXL/SC device image

in the Omega web management session interface.

Bridge Menu

From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status.

Bridge Info

Displays basic bridge information such as the LAN ID, bridge address, number of parts controlled by the bridging entity and the bridge type.

Forwarding Database

Displays the Forwarding Database table.

PN 613-50507-00 Rev D Page 39 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - The current firmware version does not allow the VLAN Name parameter to be

configured. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: noSuchName."

Discard/Aging Time Info

Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.

Spanning Tree Info

Displays spanning tree parameters such as priority and cost.

Statistics

Displays statistics about frames received/transmitted on the switch port.

RMON Menu

From the RMON menu you can view and edit the RMON MIB.

Statistics

Displays traffic statistics in the network segment attached to each port.

History Control Table

Displays the RMON History table.

Alarm Table

Displays the RMON Alarm table.

Event Table

Displays the RMON Event table.

Event Log

Displays the RMON Event log.

Port Menu

From the Port menu, you can view and edit MIB information about the port.

Utilization

Displays the port's utilization information.

Interface Info

Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.

PN 613-50507-00 Rev D Page 40 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - Valid MIB Set values for the Administration Status parameter are 'up' and 'down'.

Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Error Statistics

Displays error statistics.

Detail Info

Displays detailed port information such as duplex mode.

Note - The Port Flow Control parameter has a fixed value of 'not supported' and cannot be

modified.

Note - When the Port Speed and Mode parameter of an AT-8224XL fixed port is set to 'auto

sense' and the port is connected to a full duplex port on another device, its corresponding Duplex LED on the device image turns orange instead of green.

Note - The current firmware version allows active ports to be disabled. However, the

disabled ports' Port Link State parameter retains the value 'on-line'.

Note - Valid MIB Set values for the Port State parameter are 'enabled' and 'disabled'.

Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Note - Attempting to configure the Port Speed and Mode parameter of an AT-8216FXL/SC

fixed port to '10Mbps half-duplex' or '10Mbps full-duplex' will automatically set it to '100Mbps half-duplex' or '100Mbps full-duplex' respectively.

Note - The following parameters are not applicable to the AT-8200XL Series:

• Port Transmit Pacing Configuration

• Port MDI Configuration

• Port VDSL Rate Configuration

• Port VDSL Link Mode

Spanning Tree Info

Displays the port's spanning tree parameters.

Enable

Enables the port.

Disable

Disables the port.

Port Mirroring

Displays the information about port mirroring.

PN 613-50507-00 Rev D Page 41 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Expansion Module Notes

• When the Port Speed and Mode parameter of an AT-A14 expansion module port is set to

'auto sense' and the port is connected to a 100Mbps full duplex port on another device, its corresponding Duplex LED on the device image turns orange instead of green.

• The current firmware version does not allow the Port Speed and Mode parameter of the AT-

A14 expansion module port to be set to any value other than 'auto-sense'.

• A GBIC image is always visible on the GBIC slot of the AT-A15 expansion module image

even if there is no GBIC physically present in the slot.

• The Port Speed and Mode parameter of an AT-A15 expansion module port must match the

duplex mode of the port to which it is connected in order to establish connection.

• The current firmware version does not allow AT-View Plus Device Manager to distinguish

the AT-A16, AT-A17, and AT-A19 expansion modules from each other. With the connector type (VF-45, SC, MT-RJ) being the only difference among them, all three expansion modules have been made to share the same GIF image.

• Attempting to configure the Port Speed and Mode parameter of an AT-A16/AT-A17/AT-

A19 expansion module port to '10Mbps half-duplex' or '10Mbps full-duplex' will automatically set it to '100Mbps half-duplex' or '100Mbps full-duplex' respectively.

• The current firmware version does not allow the Port Speed and Mode parameter of the AT-

A17 expansion module ports to be set to 'auto sense'.

• When the Port Speed and Mode parameter of an AT-A18 expansion module port is set to

'auto sense' and the port is connected to a full duplex port on another device, its corresponding Duplex LED on the device image turns orange instead of green.

AT-8200XL Series

PN 613-50507-00 Rev D Page 42 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8324

This section describes AT-View Plus Device Manager menus and operations specific to the AT8324 switch.

Topics:

• Main Window

• Agent Menu

• Bridge Menu

• RMON Menu

• Port Menu

• Stacking Menu

Main Window

AT-8324

PN 613-50507-00 Rev D Page 43 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Supports up to 8 stacked AT-8324 switches.

Device Manager LEDs for AT-8324

LED State Description

PWR Green The switch is receiving power.

DUPLEX Green

Orange

The port is operating in full-duplex mode.

The port is operating in half-duplex mode.

Note - The current firmware version does not allow AT-View Plus Device Manager to support the

RPS and the Master LEDs.

Note - A GBIC image is always visible on the GBIC slot of the AT-A15 expansion module even if

there is no GBIC physically inserted.

Agent Menu

From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet.

System Info

Displays basic system information, including system name, location, contact and description.

Note - Attempting to enter more than 39 characters for the System Contact, System Name,

and System Location parameters will result in the error message: "The error occurred with 'Set' operation. Error: gen Error".

Firmware Info

Displays firmware version.

Network Info

Displays network-related information such as the addresses of the default gateway and the agents.

Manager Address Info

Displays the IP address of the management station.

Reset

Resets the switch.

Telnet

Starts a Telnet connection to the switch.

PN 613-50507-00 Rev D Page 44 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

WEB Browser

Connects to the switch's HTTP server.

Bridge Menu

From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status.

Forwarding Database

Displays the Forwarding Database table.

Discard/Aging Time Info

Displays information about the number of address entries that were learned but discarded because of lack memory or the entry's aging timer has expired.

Note - The current firmware version accepts values in the range [8-512] inclusive for the

Aging Time parameter. However, if the value entered is not a multiple of 8, the firmware will convert it to the largest multiple of 8 less than the entered value.

Spanning Tree Info

Displays spanning tree parameters such as priority and cost.

Note - When STP/RSTP is enabled, the current firmware version sets the Port State

parameter of all inactive ports to 'blocking'. As a result, inactive ports will turn yellow in ATView Plus Device Manager.

Note - When enabling/disabling STP/RSTP, connection to the AT-8324 is temporarily lost.

As a result, the following error message appears: "The error occurred with 'Set' operation. Error: time out occurred." This will not affect the application in any way.

Statistics

Displays statistics about frames received/transmitted on the switch's ports.

RMON Menu

From the RMON menu you can view and edit the RMON MIB.

Statistics

Displays traffic statistics in the network segment attached to each port.

History Control Table

Displays the RMON History table.

PN 613-50507-00 Rev D Page 45 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - The current firmware version is unable to retrieve the correct information for the

History Control Table. As a result, the following error message appears: "Failed to get MIB data."

Alarm Table

Displays the RMON Alarm table.

Event Table

Displays the RMON Event table.

Event Log

Displays the RMON Event log.

Port Menu

From the Port menu, you can view and edit MIB information about the port.

Note - The current firmware version does not allow AT-View Plus Device Manager to support the

following features:

• Spanning Tree Info

• Class of Service

• IGMP Snooping

Utilization

Displays the port's utilization information.

Interface Info

Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.

Note - The Port Type parameter returns '???(62)'.

Note - Valid MIB Set values for the Administration Status parameter are 'up' and 'down'.

Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: gen Error."

Error Statistics

Displays error statistics.

Detail Info

Displays detailed port information such as duplex mode.

Note - The current firmware version accepts from 0 up to 19 characters for the Port Name

parameter.

PN 613-50507-00 Rev D Page 46 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - The Port State parameter returns 'unknown' for active ports.

Note - When a port is configured to auto-negotiate, the current firmware version does not

always update its Port Duplex Status parameter with the correct negotiated mode. As a result, the port's Duplex LED may show up as green when it should really be orange and vice-versa.

Note - The Port Speed and Mode parameter of the 1000Base-X port on the AT-A15

expansion module can only be set to '1Gbps full-duplex'. Attempting to set this to any other value will result in the error message: "The error occurred with 'Set' operation. Error: gen Error".

Note - The Port Speed and Mode parameter of the 100/1000Base-T port on the AT-A14

expansion module can only be set to 'auto'. Attempting to set this to any other value will result in the error message: "The error occurred with 'Set' operation. Error: gen Error".

Note - The Port Speed and Mode parameter of the 100Base-FX port on the AT-A16, AT-

A17, and AT-A19 expansion modules can only be set to '100Mbps full-duplex'. Attempting to set this to any other value will result in the error message: "The error occurred with 'Set' operation. Error: gen Error".

Note - Valid MIB Set values for the Port State parameter are 'enabled' and 'disabled'.

Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Enable

Enables the port.

Note - Expansion module ports cannot be enabled. Attempting to do so will result in the error

message: "The error occurred with 'Set' operation. Error: gen Error".

Disable

Disables the port.

Note - Expansion module ports cannot be disabled. Attempting to do so will result in the

error message: "The error occurred with 'Set' operation. Error: gen Error".

Port Mirroring

Displays port mirroring parameters and allows configuration of port mirroring state, source, and destination.

PN 613-50507-00 Rev D Page 47 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Stacking Menu

From the Stacking menu, you can view basic switch information as well as stacking information.

Stacking Info

Displays information such as Product Type, Port Count and Uplink Types for all switches in the stack.

AT-8324

PN 613-50507-00 Rev D Page 48 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8324SX

This section describes AT-View Plus Device Manager menus and operations specific to the AT8324SX switch.

Topics:

• Main Window

• Agent Menu

• Bridge Menu

• RMON Menu

• Port Menu

• Stacking Menu

PN 613-50507-00 Rev D Page 49 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Main Window

AT-8324SX

Supports up to 4 stacked switches.

PN 613-50507-00 Rev D Page 50 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Device Manager LEDs for AT-8324SX

LED State Description

PWR Green The switch is receiving power.

RPS

DUPLEX

STACK

Green

Gray

Orange

Redundant power is ON.

Redundant power is OFF.

The port is operating in full-duplex mode.

The port is operating in half-duplex mode.

Green The switch's position in the switch stack.

Note - When multiple units of AT-8324SX are stacked together, port numbering is continuous. This

means that the first unit on the stack will have ports numbered from 1 to 32. The second unit on the stack will have ports numbered from 33 to 64. The third unit will have ports numbered from 65 to 96 and the fourth unit from 97 to 128. It is assumed that the maximum number of ports per unit is 32, 24 fixed ports plus up to 8 uplink ports.

Agent Menu

From the Agent menu, you can view and edit the system information for the switch, or log into the CLI using Telnet.

System Info

Displays basic system information, including system name, location, contact and description.

Note - AT-View Plus Device Manager allows the user to enter up to 255 characters for the

System Contact, System Name, and System Location parameters.

TFTP Download Management

Displays TFTP information.

Note - AT-View Plus Device Manager allows the user to enter up to 80 characters for the

TFTP File Name parameter but truncates it to 47 characters.

Note - AT-View Plus Device Manager does not allow the user to set the Download Mode

parameter to 'temporary'. Attempting to do so will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Reset

Displays the reset table that allows you to configure reset parameters before restarting the management agent.

PN 613-50507-00 Rev D Page 51 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Telnet

Starts a Telnet connection to the switch.

WEB Browser

Connects to the switch's HTTP server.

Bridge Menu

From the Bridge menu, you can view and edit bridge information, such as the forwarding database and spanning tree status.

Forwarding Database

Displays the Forwarding Database table.

Discard/Aging Time Info

Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.

Note - Valid MIB Set values for the Aging Time parameter should range from 10 to 412.

However, the current firmware version allows it to be set to a value greater than 412 all the way up to 1000000.

Spanning Tree Info

Displays spanning tree parameters such as priority and cost.

Statistics

Displays statistics about frames received/transmitted on the switch's ports.

RMON Menu

From the RMON menu, you can view and edit the RMON mib.

Statistics

Displays traffic statistics in the network segment attached to each port.

History Control Table

Displays the RMON history table.

Alarm Table

Displays the RMON alarm table.

Event Table

Displays the RMON event table.

Event Log

PN 613-50507-00 Rev D Page 52 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Displays the RMON event log.

Port Menu

From the Port menu, you can view and edit MIB information about the port.

Note - The current firmware version does not allow Port Menu to support the Class of Service.

Utilization

Displays the port's utilization information.

Interface Info

Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.

Note - Valid MIB Set values for the Administration Status parameter are 'up' and 'down'.

Attempting to set this parameter to any other value will result in the following error message: "The error occurred with 'Set' operation. Error: bad value." This will not affect the application in any way.

Error Statistics

Displays error statistics.

Detail Info

Displays detailed port information such as duplex mode.

Note - The current firmware version does not support port naming.

Note - When the Port Speed and Mode parameter of a fixed port is set to 'auto sense', the

current firmware version is unable to provide information on the negotiated mode of the port. As a result, the port's Duplex LED may show up as green when it should really be orange and vice-versa.

Note - Valid MIB Set values for the Port Speed and Mode parameter of the AT-B17

expansion module ports are '100Mbps full-duplex' or '100Mbps half-duplex'. Attempting to set this to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value".

Note - Valid MIB Set values for the Port Speed and Mode parameter of the AT-B15

expansion module port are 'auto sense', '1Gbps full-duplex' or '1Gbps half-duplex'. Attempting to set this to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value".

Note - The Module ID and Port Number parameters return 'noSuchName'.

PN 613-50507-00 Rev D Page 53 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Spanning Tree Info

Displays the port's spanning tree parameters.

Enable

Enables the port.

Disable

Disables the port.

Port Mirroring

Displays port mirroring parameters and allows configuration of port mirroring state, source, and destination.

IGMP Snooping

Displays the current state of IGMP Snooping and allows reconfiguration.

Note - Valid MIB Set values for the IGMP Report Delay parameter should range from 5 to

30. However, the current firmware version does not allow it to be set to a value greater than

10. Attempting to do so will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Stacking Menu

From the Stacking menu, you can view basic switch information as well as stacking information.

Stacking Info

Displays information such as Hardware Version, Firmware Version, Expansion Slot, and Role In System for all switches in the stack.

AT-8324SX

PN 613-50507-00 Rev D Page 54 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8300GB Series

This section describes AT-View Plus Device Manager menus and operations specific to the AT8300GB Series.

Topics:

• Main Window

• Agent Menu

• Bridge Menu

• RMON Menu

• Port Menu

• Stacking Menu

PN 613-50507-00 Rev D Page 55 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Main Window

AT-8326GB

PN 613-50507-00 Rev D Page 56 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

The AT-8326GB supports up to 6 AT-8326GB stacked switches or any of the following mixed stack combinations of AT-8326GB and AT-8350GB switches:

• Two AT-8326GB switches and one AT-8350GB switch

• Two AT-8326GB switches and two AT-8350GB switches

• Three AT-8326GB switches and one AT-8350GB switch

• Four AT-8326GB switches and one AT-8350GB switch

Note - When 3 or more AT-8326GB devices are stacked together, expect the twisted pair port image

of Port 26 on the last device on the stack to turn green. This is because the current firmware version returns 'on-line' for the Port Link State parameter of the port even if there is no link established.

AT-8350GB

The AT-8350GB supports up to 3 stacked AT-8350GB switches.

Note - The current firmware version does not allow AT-View Plus Device Manager to support the

RPS LED.

PN 613-50507-00 Rev D Page 57 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - The current firmware version does not allow AT-View Plus Device Manager to support

expansion modules that may be installed on the AT-8350GB.

Device Manager LEDs for AT-8300GB Series

LED State Description

PWR Green The switch is receiving power.

STACK ID Green The switch's position in the switch stack.

DUPLEX

Green

Orange

The port is operating in full-duplex mode.

The port is operating in half-duplex mode.

Note - Status information for the gigabit ports will always be reflected on the RJ-45 gigabit port

images regardless of whether the gigabit ports have been set to operate as GBIC ports or as Twisted Pair ports.

Note - When Global STP is enabled, the current firmware version sets the Port State parameter of

inactive ports to 'blocking'. As a result, expect port images for inactive ports to turn yellow in ATView Plus Device Manager .

Note - The current firmware version does not allow AT-View Plus Device Manager to detect the

presence or absence of a GBIC module in any of the GBIC slots. As a result, the GBIC slots on the device image will remain empty regardless of whether or not GBIC modules are physically present in the slots.

Agent Menu

From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet.

System Info

Displays basic system information, including system name, location, contact and description.

Note - The current firmware version does not allow multiple-word values for the System

Name parameter.

Note - AT-View Plus Device Manager allows the user to enter up to 255 characters for the

System Contact, System Name and System Location parameters but the current firmware version truncates them to 64 characters.

Firmware Info

Displays the version of the software running on the managed device.

PN 613-50507-00 Rev D Page 58 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Network Info

Displays network-related information such as the device IP address and the default gateway address.

Note - The current firmware version does not save changes made to the DNS Server and the

Default Domain Name parameters.

DHCP Info

Displays DHCP information including the DHCP System Group and DHCP Timer Group.

Manager Address Info

Displays the IP address of the management station.

Reset

Resets the switch.

Telnet

Starts a Telnet connection to the switch.

WEB Browser

Connects to the switch's HTTP server.

Bridge Menu

From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status.

Forwarding Database

Displays the Forwarding Database table.

Discard/Aging Time Info

Displays information about the number of address entries that were learned but discarded because of lack of memory or the entry's aging timer has expired.

Note - The current firmware version accepts values in the range [10-1000000] inclusive for

the Aging Time parameter.

Spanning Tree Info

Displays spanning tree parameters such as priority and cost.

Statistics

Displays statistics about frames received/transmitted on the switch's ports.

PN 613-50507-00 Rev D Page 59 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

RMON Menu

From the RMON menu you can view and edit the RMON MIB.

Statistics

Displays traffic statistics in the network segment attached to each port.

History Control Table

Displays the RMON History table.

Alarm Table

Displays the RMON Alarm table.

Event Table

Displays the RMON Event table.

Event Log

Displays the RMON Event log.

Port Menu

From the Port menu, you can view and edit MIB information about the port.

Utilization

Displays the port's utilization information.

Interface Info

Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.

Note - Valid MIB Set values for the Administration Status parameter are 'up' and 'down'.

Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: gen Error."

Detail Info

Displays detailed port information such as duplex mode.

Note - The Port Transmit Pacing Configuration parameter is not applicable to the AT-

8300GB Series.

Note - The Port VLAN Tag Priority parameter has a fixed value of 'use vlan priority' and

cannot be modified.

PN 613-50507-00 Rev D Page 60 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - The current firmware version does not allow the Port Bridge ID parameter to be

configured. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: bad value".

Note - When a port's Port Speed and Mode parameter is set to 'auto sense', the current

firmware version does not update its Port Duplex Status parameter with the negotiated mode. As a result, the port's Port Duplex Status parameter will always display 'auto sense' and its corresponding Duplex LED will always be green regardless of the actual connection mode.

Note - The Port Name parameter is not applicable to the AT-8300GB Series.

Note - Valid MIB Set values for the Port State parameter are 'enabled' and 'disabled'.

Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Spanning Tree Info

Displays the port's spanning tree parameters.

Enable

Enables the port.

Disable

Disables the port.

QoS

Displays QoS parameters and allows enabling of QoS status and setting priority queue.

Port Mirroring

Displays port mirroring parameters and allows configuration of port mirroring state, source and destination.

IGMP Snooping

Displays the current state of IGMP Snooping and allows reconfiguration.

Stacking Menu

From the Stacking menu, you can view basic switch information as well as stacking information.

Stacking Info

Displays information such as Product Type, Port Count, and Uplink Types for all switches in the stack.

Note - The Uplink Port A MDA Type and Uplink Port B MDA Type parameters return

incorrect values.

PN 613-50507-00 Rev D Page 61 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - The Security Action parameter returns '???(0)' when the Security Configuration

parameter is set to 'disabled'.

AT-8300GB Series

PN 613-50507-00 Rev D Page 62 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8400

This section describes AT-View Plus Device Manager menus and operations specific to the AT8400 switch.

Topics:

• Main Window

• Agent Menu

• Bridge Menu

• RMON Menu

• Port Menu

• Stacking Menu

PN 613-50507-00 Rev D Page 63 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Main Window

AT-8400

PN 613-50507-00 Rev D Page 64 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Device Manager LEDs for AT-8401 Management Module

LED State Description

FAN A

FAN B

MASTER

Green

Gray

Green

Gray

Green

Gray

FAN TRAY A is installed and is operating correctly.

FAN TRAY A is not installed.

FAN TRAY B is installed and is operating correctly.

FAN TRAY B is not installed.

The switch is the master of an enhanced stack.

The switch is either a slave switch of an enhanced stack or the switch is not a member of an enhanced stack.

RPS

Green

The switch is receiving power from the redundant power supply (PWR B).

Gray

The switch is receiving power from the main power supply (PWR A).

PWR

Green

Gray (Only if

The switch is receiving power from the main power supply (PWR A).

The main power supply is not functioning.

RPS is installed)

Note - Please refer to AT-8400 Line Cards

for the operations and behavior of the line cards installed

on the chassis.

Note - The FAN A and FAN B LEDs are always green regardless of whether or not fan trays are

actually installed.

Note - The PWR LED is always green and the RPS LED is always gray regardless of whether the

switch is receiving power from the main power supply or the redundant power supply.

Note - Some parameters, when configured, may at times cause a temporary loss of connection. When

this happens, the following error message appears: "The error occurred with 'Set' operation. Error: time out occurred.". This will not affect the application in any way.

Agent Menu

From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet.

PN 613-50507-00 Rev D Page 65 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

System Info

Displays basic system information, including system name, location, contact and description.

Network Info

Displays network-related information such as the addresses of the default gateway and the agents.

Note - The current firmware version does not allow the DNS Server and Default Domain

Name parameters to be configured. Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation. Error: gen Error.".

Chassis Info

Displays chassis information including the firmware information.

Note -The current firmware version does not allow the Power A Status and Power B Status

parameters to be configured. Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation. Error: gen Error.".

Line Card Info

Displays information for each line card including line card type and line card temperature.

MAC Address Table

Displays a list of static MAC address configured on the switch.

Note - Valid MIB Set values for the MAC Address Entry Status parameter are 'active', 'not in

service' and 'destroy'. Attempting to set this parameter to any other value will result in error message: "The error occurred with 'Set' operation. Error: bad value".

Reset

Resets the switch.

Telnet

Starts a Telnet connection to the switch.

WEB Browser

Connects to the switch's HTTP server.

Bridge Menu

From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status.

Forwarding Database

Displays the Forwarding Database table.

PN 613-50507-00 Rev D Page 66 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - It may take some time to retrieve Forwarding Database information. As a result, all

the Forwarding Database parameters may reflect the value 'retry over occurred'. To avoid this, click on File -> Property -> Polling options and set the Polling Interval parameter to 25 seconds or longer.

Discard/Aging Time Info

Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.

Spanning Tree Info

Displays spanning tree parameters such as spanning tree status and spanning tree version.

Note - When setting the Spanning Tree Status parameter to 'enabled', connection to the AT-

8400 is temporarily lost. As a result, the following error message appears: "The error occurred with 'Set' operation. Error: time out occurred.".

Note - Setting the value of the Spanning Tree Version parameter to 'stp' will result in a

permanent loss of connection. To re-establish connection, restart the device.

Statistics

Displays statistics about frames received/transmitted on the switch's ports.

Note - Ports are numbered continuously from top to bottom, across all installed line cards,

starting from the leftmost line card all the way through the rightmost line card.

RMON Menu

From the RMON menu you can view and edit the RMON MIB.

Statistics

Displays traffic statistics in the network segment.

History Control Table

Displays the RMON History table.

Note - The current firmware version does not support the "historyControlTable" MIB object

of RFC1757. As a result, AT-View Plus Device Manager displays the error message "Failed to get MIB data." when the History Control Table option is selected from the RMON menu.

Alarm Table

Displays the RMON Alarm table.

Event Table

Displays the RMON Event table.

PN 613-50507-00 Rev D Page 67 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Event Log

Displays the RMON Event log.

Port Menu

From the Port menu, you can view and edit MIB information about the port.

Note - Ports are numbered continuously from top to bottom, across all installed line cards, starting

from the leftmost line card all the way through the rightmost line card. This applies to the following submenu options:

• Utilization

• Interface Info -> Standard

• Error Statistics -> Standard

• Spanning Tree Info

Utilization

Displays the port's utilization information.

Interface Info

Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.

Note - Valid MIB Set values for the Administration Status parameter are 'up' and 'down'.

Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value.".

Error Statistics

Displays error statistics such as alignment error frames and carrier sense errors.

Detail Info

Displays detailed port information such as duplex mode.

Note - The current firmware version does not allow the Port Name parameter to be set to

NULL. Attempting to set this parameter to NULL will result in the error message: "The error occurred with 'Set' operation. Error: bad value.".

Spanning Tree Info

Displays the port's spanning tree parameters.

Note - The current firmware version does not allow the Port parameter to be configured.

Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: readOnly".

PN 613-50507-00 Rev D Page 68 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Port Security

Displays the port security attributes for each physical port present in the switch.

Enable

Enables the port.

Disable

Disables the port.

Port Mirroring

Displays port mirroring parameters and allows configuration of port mirroring state and port's source list.

Note - Valid MIB Set values for the Port Mirroring Configuration Entry Status parameter are

'active', 'not in service' and 'destroy'. Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value.".

Stacking Menu

From the Stacking menu, you can view basic switch information as well as stacking information.

Stacking Info

Displays information such as Stack Switch ID, Stack Switch MAC Address, Stack Switch Name, Stack Switch Mode, Stack Switch Software Version and Stack Switch Model for all switches in the stack.

AT-8400

PN 613-50507-00 Rev D Page 69 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8400 Line Cards

This section describes the AT-8400 Line Cards supported by AT-View Plus Device Manager. If line cards are installed on the AT-8400 chassis at the time AT-View Plus Device Manager is called, they will be displayed in their corresponding slots on the chassis image.

• AT-8411

• AT-8412

• AT-8413

• AT-8414

AT-8411

LED State Description

DUPLEX

Note - When a port on the AT-8411 line card is configured to auto-negotiate and is connected to a

10/100 Mbps full-duplex port on another device, the current firmware version returns the value 'halfduplex' for the Port Duplex Status parameter. As a result, the Duplex LED turns orange instead of green.

PN 613-50507-00 Rev D Page 70 of 253

Green

Orange

The port is operating in full-duplex.

The port is operating in half-duplex.

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8412

AT-8412/MT AT-8412/SC

LED State Description

DUPLEX Green The port is operating in full-duplex.

Note – The current firmware version does not allow the Port Flow Control parameter of ports on the

AT-8412/MT and AT-8412/SC line cards to be set to ‘auto’. Attempting to set this parameter to ‘auto’ will result in the error message: “The error occurred with ‘Set’ operation. Error: gen Error”.

PN 613-50507-00 Rev D Page 71 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8413

AT-8413GB/T

LED State Description

DUPLEX

Green

Orange

The port is operating in full-duplex.

The port is operating in half-duplex.

Note - A GBIC image is always visible on the GBIC slot of the AT-8413GB/T line card image even

if there is no GBIC physically present in the slot.

Note - Status information for the AT-8413GB/T ports will always be reflected on the RJ-45 port

image regardless of whether the port that is in actual use is the GBIC port or the twisted pair port.

Note - When the 10/100/1000Base-T port of the AT-8413GB/T line card is configured to auto-

negotiate and is connected to a 10/100Mbps full-duplex port on another device, the current firmware version returns the value 'half-duplex' for the Port Duplex Status parameter. As a result, the Duplex LED turns orange instead of green.

PN 613-50507-00 Rev D Page 72 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-8414

AT-8414/SC AT-8414/ST

LED State Description

DUPLEX

Green

Orange

The port is operating in full-duplex.

The port is operating in half-duplex.

Note - The Port Negotiation parameter of ports on the AT-8414/SC and AT-8414/ST line cards has a

fixed value of '10Mbps full-duplex' and cannot be modified.

AT-8400 Line Cards

PN 613-50507-00 Rev D Page 73 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-9006 Family

This section describes AT-View Plus Device Manager menus and operations specific to the AT9006SX/SC and AT-9006T switches.

Topics:

• Main Window

• Agent Menu

• Bridge Menu

• RMON Menu

• VLAN Menu

• Port Menu

Main Window

AT-9006SX/SC

PN 613-50507-00 Rev D Page 74 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-9006T

Device Manager LEDs for AT-9006 Family

LED State Description

PWR Green The switch is receiving power.

RPS Green

Gray

DUPLEX Green

Orange

An optional redundant power supply is connected to the switch.

There is no redundant power supply connected to the switch.

The port is operating in full-duplex mode.

The port is operating in half-duplex mode.

Note - Ports on the expansion modules are numbered starting from 7. Slot A's leftmost port has the

smallest number and Slot B's rightmost port has the largest number.

Agent Menu

From the Agent menu, you can view and edit the system information for the device, or log into the CLI using telnet.

System Info

Displays basic system information, including system name, location, contact and description.

PN 613-50507-00 Rev D Page 75 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Firmware Info

Displays firmware version.

Network Info

Displays network-related information such as agent's and default gateway address.

Manager Address Info

Displays management station's IP address.

Reset

Reset the switch.

Telnet

Connect to the switch's telnet service.

Bridge Menu

From the Bridge menu, you can view and edit information such as forwarding database and spanning tree status.

Forwarding Database

Displays forwarding database table.

Discard/Aging Time Info

Displays information about number of address entry that was learned but discarded because of the reason such as memory shortage and entry's aging time.

Spanning Tree Info

Displays spanning tree parameters such as priority and cost.

Statistics

Displays statistics of frames received/transmitted on the switch port.

RMON Menu

From the RMON menu, you can view and edit RMON MIB.

Note - Since RMON data may be large, it may take some time for information to appear.

Statistics

Displays traffic statistics in the network segment attached to each port.

History Control Table

Displays RMON History table.

PN 613-50507-00 Rev D Page 76 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Alarm Table

Displays RMON Alarm table.

Event Table

Displays RMON Event table.

Event Log

Displays RMON Event log.

VLAN Menu

From the VLAN menu, you can view the list of VLAN and member ports.

Note - You cannot modify VLAN configuration on the AT-9006 Family using the VLAN menu.

Name List

Displays configured VLAN names.

Port Info

Displays VLAN to which the port belongs.

Port Menu

From the Port menu, you can view and edit MIB information about the port.

Utilization

Displays port's utilization information.

Interface Info

Displays port statistics such as number of frames received/transmitted on the port, bytes received/transmitted on the port and port status.

Error Statistics

Displays error statistics.

Detail Info

Displays detailed port information such as duplex mode, speed, spanning tree protocol status and switching mode.

Spanning Tree Info

Displays port's spanning tree parameters.

Enable

Enables the port.

PN 613-50507-00 Rev D Page 77 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Disable

Disables the port.

AT-9006 Family

PN 613-50507-00 Rev D Page 78 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-9410GB

This section describes AT-View Plus Device Manager menus and operations specific to the AT9410GB switch.

Topics:

• Main Window

• Agent Menu

• Bridge Menu

• RMON Menu

• Port Menu

Main Window

AT-9410GB

Device Manager LEDs for AT-9410GB

LED State Description

PWR Green The switch is receiving power.

DUPLEX Green

Orange

The port is operating at full-duplex mode.

The port is operating at half-duplex mode.

Note - When Global STP is enabled, the current firmware version sets the Port State parameter of

PN 613-50507-00 Rev D Page 79 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

inactive ports to 'blocking'. As a result, expect port images for inactive ports to turn yellow in ATView Plus Device Manager.

Note - When a port on the AT-9410GB is set to 'auto sense' and is connected to a half-duplex port on

another device, its corresponding Duplex LED on the device image turns green instead of orange.

Note - A GBIC image is always visible on each of the GBIC slots of the device image even if there

are no GBICs physically inserted.

Agent Menu

From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet.

System Info

Displays basic system information, including system name, location, contact and description.

Note - The current firmware version does not allow the user to enter multiple-word values for

the System Name parameter.

Note - AT-View Plus Device Manager allows the user to enter up to 255 characters for the

System Contact, System Name, and System Location parameters but truncates them to 64 characters.

Firmware Info

Displays firmware version.

Network Info

Displays network-related information such as the addresses of the default gateway and the agents.

Note - The current firmware version does not save changes made to the DNS Server and the

Default Domain Name parameters.

DHCP Info

Displays DHCP information including the DHCP System Group and DHCP Timer Group.

Manager Address Info

Displays the IP address of the management station.

Device Info

Displays general information about the switch.

Note - The Security Action parameter returns '???(0)' when the Security Configuration

parameter is set to 'disabled'.

PN 613-50507-00 Rev D Page 80 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

DHCP Info

Displays DHCP information including the DHCP System Group and DHCP Timer Group.

Reset

Resets the switch.

Telnet

Starts a Telnet connection to the switch.

WEB Browser

Connects to the switch's HTTP server.

Bridge Menu

From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree status.

Bridge Info

Displays basic bridge information such as the LAN ID, bridge address, number of ports and the bridge type.

Forwarding Database

Displays the Forwarding Database table.

Discard/Aging Time Info

Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.

Note - The current firmware version accepts values in the range [10-1000000] inclusive for

the Aging Time parameter.

Spanning Tree Info

Displays spanning tree parameters such as priority and cost.

Statistics

Displays statistics about frames received/transmitted on the switch's ports.

RMON Menu

From the RMON menu you can view and edit the RMON MIB.

Statistics

Displays traffic statistics in the network segment attached to each port.

History Control Table

PN 613-50507-00 Rev D Page 81 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Displays the RMON History table.

Alarm Table

Displays the RMON Alarm table.

Event Table

Displays the RMON Event table.

Event Log

Displays the RMON Event log.

Port Menu

From the Port menu, you can view and edit MIB information about the port.

Utilization

Displays the port's utilization information.

Interface Info

Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.

Note - Valid MIB Set values for the Administration Status parameter are 'up' and 'down'.

Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: gen Error."

Detail Info

Displays detailed port information such as duplex mode.

Note - The Port Name parameter is not applicable to the AT-9410GB.

Note - The current firmware version does not allow the Port VLAN Tag Priority parameter to

be configured. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Note - The Port Transmit Pacing Configuration parameter is not applicable to the AT-

9410GB.

Note - AT-View Plus Device Manager allows the user to disable an active port. However, the

disabled port's Port Link State parameter retains the value 'on-line'.

Note - When connection is established between a twisted pair port that is configured to auto-

negotiate and a port on another device that is configured to operate at 10/100Mbps full/half duplex, expect the link to drop when the twisted pair port's speed and mode is changed to match the speed and mode of the port on the other device.

PN 613-50507-00 Rev D Page 82 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - Valid MIB Set values for the Port State parameter are 'enabled' and 'disabled'.

Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Spanning Tree Info

Displays the port's spanning tree parameters.

Enable

Enables the port.

Disable

Disables the port.

QoS

Displays QoS parameters and allows enabling of QoS status and setting priority queue.

Port Mirroring

Displays port mirroring parameters and allows configuration of port mirroring state, source and destination.

IGMP Snooping

Displays the current state of IGMP Snooping and allows reconfiguration.

AT-9410GB

PN 613-50507-00 Rev D Page 83 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-FH800u

This section describes AT-View Plus Device Manager menus and operations specific to the ATFH812u and AT-FH824u hubs.

Topics:

• Main Window

• Agent Menu

• Hub Menu

• Module Menu

• RMON Menu

• Port Menu

Main Window

AT-FH800u Series

Device Manager LEDs for AT-FH800u

LED State Description

PWR Green The hub is receiving power.

PN 613-50507-00 Rev D Page 84 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Agent Menu

From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet.

System Info

Displays basic system information, including system name, location, contact and description.

Network Info

Displays network-related information such as the device's IP address, and the default gateway address.

Note - The current firmware version returns 'noSuchName' for the following parameters:

• Server Slip Address

• Host Slip Address

• Temporary Server Slip Address

• Temporary Host Slip Address

Firmware Info

Displays the version of the software running on the managed device.

Manager Address Info

Displays the management station's IP address.

Note - The current firmware version does not allow the Status parameter to be set to 'under

change'. Attempting to set it to 'under change' will result in the error message "The error occurred with 'Set' operation. Error: bad value.".

Note - By default, the Status parameters are set to 'invalid'. To be able to set them to 'valid',

their corresponding IP Address parameters must first be set to valid values. Failing to do so will result in the error message "The error occurred with 'Set' operation. Error: time out occured."

Reset

Resets the system

Telnet

Starts a Telnet connection to the hub.

WEB Browser

Connects to the hub's HTTP server.

PN 613-50507-00 Rev D Page 85 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Hub Menu

From the Hub menu, you can check traffic statistics and hub's status. It also lets you perform a selftest.

Status

Displays hub information such as stacking status.

Module Menu

From the Module menu, you can view and edit MIB information about a selected hub in the stacked group.

Status

Displays information such as operation status and object identifier.

Note - The current firmware version returns 'noSuchName' for the following parameters:

• Module Description

• Last Update Time and Date

RMON Menu

From the RMON menu, you can view and edit RMON MIB.

Statistics

Displays traffic statistics in the network segment attached to each port.

History Control Table

Displays RMON History table.

Alarm Table

Displays RMON Alarm table.

Event Table

Displays RMON Event table.

Event Log

Displays RMON Event log.

Segment Info

Displays number of segments and others.

Segment Status

Displays RMON configuration information of each segment.

PN 613-50507-00 Rev D Page 86 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Port Menu

From the Port menu, you can view and edit MIB information about hub's ports.

Statistics

Displays port statistics such as number of frames received/transmitted on the port, bytes received/transmitted on the port and port status.

Status

Displays whether the port is enabled or disabled, whether it is partitioned and other status information.

Detail Status

Displays information such as port name, LED status and polarity.

Note - A link between a port on the hub and a port on another device can only be established

if the port on the other device is configured to auto-negotiate.

Security Info

Displays source MAC addresses of frames received on the port.

Note - Valid MIB Set values for the Learn Action parameter are 'inactive' and 'active'.

Attempting to set this parameter to any other value will result in the error message "The error occurred with 'Set' operation. Error: bad value.".

Note - The current firmware version does not allow the user to configure the MAC Address

parameter. Attempting to configure it will result in the error message "The error occurred with 'Set' operation. Error: bad value.".

Enable

Enables the port.

Disable

Disables the port.

AT-FH800u

PN 613-50507-00 Rev D Page 87 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-AR200E

This section describes AT-View Plus Device Manager menus and operations specific to the ATAR240E, AT-AR250E, and AT-AR255E ADSL bridge/routers.

Topics:

• Main Window

• Agent Menu

• Routing Menu

• Bridge Menu

• ADSL Menu

• ATM Menu

• PPP Menu

• Port Menu

Main Window

AT-AR240E

PN 613-50507-00 Rev D Page 88 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

AT-AR250E

AT-AR255E

Device Manager LEDs for AT-AR200 Series

LED State Description

PWR Green The router is receiving power.

Note - The current firmware version does not allow AT-View Plus Device Manager to support the

Reset button.

PN 613-50507-00 Rev D Page 89 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - The port speed displayed on the Ethernet port images is always '100' even if the Ethernet port

is connected to a 10Mbps port on another device.

Note - The four Ethernet ports on the device operate as a single port. As a result, even if connection

is established on just one port, all four ports will turn green.

Note - Expect the ADSL port to be green even if there is no physical connection established.

Note - The current firmware version does not allow you to disable the Ethernet ports.

Note - The current firmware version does not allow you to manually configure the speed of the

Ethernet ports.

Agent Menu

From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet.

System Info

Displays basic system information, including system name, location, contact and description.

Note - The current firmware version returns 'enterprises' instead of the actual OID of the

device for the System Unique Object ID parameter.

Note - Clicking on the 'Set MIB Value' button several times when configuring System Info

parameters will result in the error message: "The error occurred with 'Set' operation. Error: time out occurred."

Note - The current firmware version does not allow System Info parameters to be configured

at the same time. Attempting to do so will result in the error message: "The error occurred with 'Set' operation. Error: time out occurred."

Telnet

Starts a Telnet connection to the router.

WEB Browser

Connects to the router's HTTP server.

Routing Menu

From the Routing menu, you can view and edit information about the router's IP routing functions.

ARP Table

Displays the mapping of IP addresses to MAC addresses (the ARP cache) on the router.

PN 613-50507-00 Rev D Page 90 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - The current firmware version does not allow the user to configure the Physical

Address parameter. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: gen Error."

Address Table

Displays the list of IP interfaces and their IP addresses on the router.

Route Table

Displays the IP routing table on the router.

Note - The current firmware version does not allow the user to configure the Destination Port

Number parameter. Attempting to configure this parameter will result in the error messages: "The error occurred with 'Set' operation. Error: gen Error." or "The error occurred with 'Set' operation. Error: bad value."

Note - The current firmware version does not allow the following parameters to be

configured:

• Destination Metric 1

• Destination Metric 2

• Destination Metric 3

• Destination Metric 4

• Next Hop Address

• Routing Type

• Route Updated Seconds

• Routing Mask

• Destination Metric 5

Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation. Error: gen Error."

IP Statistics

Displays statistics about IP routing, including the number of IP datagrams received.

Note - The current firmware version does not allow the Forwarding Status and the Default

TTL parameters to be configured. Attempting to configure these will result in the error message: "The error occurred with 'Set' operation. Error: gen Error."

ICMP Statistics

Displays ICMP statistics.

UDP Statistics

Displays UDP statistics.

PN 613-50507-00 Rev D Page 91 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

TCP Statistics

Displays TCP statistics.

Note - The current firmware version does not allow the user to configure the TCP

Connection State parameter. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Bridge Menu

From the Bridge menu, you can view and edit bridge information such as the forwarding database, discard/aging time information, and spanning tree status.

Forwarding Database

Displays the Forwarding Database table.

Discard Aging Time Info

Displays information about the number of address entries that were learned but discarded because either there was a lack of memory or the entry's aging timer expired.

Spanning Tree Info

Displays spanning tree parameters such as priority and cost.

ADSL Menu

From the ADSL menu, you can view and edit ADSL information such as the line attributes, physical layer components, channel information, performance statistics, and configuration profiles.

Note - The ADSL Menu does not apply to the AT-AR255E.

ADSL Line

Displays attributes of the ADSL line.

Note - The current firmware version does not allow the Configuration Profile and the Alarm

Configuration Profile parameters to be configured. Attempting to configure these will result in the error message: "The error occurred with 'Set' operation. Error: gen Error."

ATU Remote

ATUR Physical Layer Inventory

Displays the physical layer parameters of each remote ADSL transmission unit.

ATUR Channels Displays ATUR Channel information like interleave delay, transmit rate, and length of the channel data-block.

ATUR Performance Data

PN 613-50507-00 Rev D Page 92 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Displays ATUR performance statistics like frame failures, signal failures and power failures.

Note - The ATUR Performance Data sub-menu option does not display the correct

parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.

ATUR Performance Data by Interval Displays collection of ATUR performance statistics in 15-minute intervals.

Note - The ATUR Performance Data by Interval sub-menu option does not display the

correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.

ATUR Channel Performance Data Displays ATUR channel performance statistics like received blocks, transmitted blocks, and error counts.

ATUR Channel Performance Data by Interval Displays collection of ATUR channel performance statistics in 15-minute intervals.

Note - The ATUR Channel Performance Data sub-menu option does not display the correct

parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.

Configuration Profiles

Displays a list of parameters that represents the configuration of an ADSL modem.

Note - The Configuration Profiles sub-menu option does not display the correct parameters.

Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.

Alarm Configuration Profiles

Displays alarm-related information.

Note - The Alarm Configuration Profiles sub-menu option does not display the correct

parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.

ATM Menu

From the ATM menu, you can view and edit ATM and AAL5-related information such as ATM interfaces, ATM virtual links, ATM cross-connects, AAL5 entities, and AAL5 connections.

Interface Configuration

Displays ATM interface configuration information.

PN 613-50507-00 Rev D Page 93 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - The current firmware version does not allow the following parameters to be

configured:

• Max VPC

• Max VCC

• Max Active VPI Bits

• Max Active VCI Bits

• ILMI VPI

• ILMI VCI

• Neighbor IP Address

• Neighbor Name

Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation. Error: gen Error."

Interface DS3 PLCP

Displays DS3 PLCP configuration and state parameters.

Note - The Interface DS3 PLCP sub-menu option does not display the correct parameters.

Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.

Interface TC Sublayer

Displays TC Sublayer configuration and state parameters.

Note - The Interface TC Sublayer sub-menu option does not display the correct parameters.

Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.

Traffic Descriptor

Displays information on the ATM traffic descriptor type and its associated parameters.

Note - The current firmware version does not allow the following parameters to be

configured:

• Type

• Parameter 1

• Parameter 2

• Parameter 3

• Parameter 4

• Parameter 5

• QoS Class

• Status

Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation. Error: gen Error."

Virtual Path Link (VPL)

PN 613-50507-00 Rev D Page 94 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Displays configuration and state information for a bi-directional Virtual Path Link.

Note - The Virtual Path Link (VPL) sub-menu option does not display the correct

parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.

Virtual Channel Link (VCL)

Displays configuration and state information for a bi-directional Virtual Channel Link.

Note - AT-AR240E : The current firmware version does not allow the following parameters

to be configured:

• Administrative Status

• Receive Traffic Descriptor Index

• Transmit Traffic Descriptor Index

• AAL Type

• AAL5 CPCS Transmit SDU Size

• AAL5 CPCS Receive SDU Size

• AAL5 Encapsulation Type

Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation. Error: gen Error".

Note - AT-AR240E: The Port Number parameter and the Virtual Channel Link (VCL)

parameters are not relevant and should be ignored.

Note - AT-AR240E : The current firmware version does not allow the Status parameters to

be configured. Attempting to configure them will result in the error message: "The error occurred with 'Set' operation. Error: bad value." or "The error occurred with 'Set' operation. Error: gen Error".

Note - AT-AR250E/AT-AR255E : The Virtual Channel Link (VCL) sub-menu option does

not display the correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.

Virtual Path (VP) Cross Connect

Displays configuration and state information of all point-to-point , point-to-multipoint, or multipoint-to-multipoint VP cross connect.

Note - The Virtual Path (VP) Cross Connect sub-menu option does not display the correct

parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.

Virtual Channel (VC) Cross Connect

Displays configuration and state information of a bi-directional VC cross connect.

PN 613-50507-00 Rev D Page 95 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - The Virtual Channel (VC) Cross Connect sub-menu option does not display the

correct parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.

AAL5 Performance Statistics

Displays performance statistics information associated with an AAL5 virtual channel connection.

Note - The AAL5 Performance Statistics sub-menu option does not display the correct

parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.

PPP Menu

From the PPP menu, you can view and edit Point-to-Point Protocol information such as Link Control Protocol information, Link Quality Report information, PPP tests, MAC Bridging over PPP, IP over PPP, and security protocol.

PPP Link Group

PPP Link Status

Displays management information about a particular PPP Link.

PPP Link Configuration

Displays configuration information about a particular PPP Link.

Note - The current firmware version does not allow the Initial MRU parameter to be

configured. Attempting to configure this parameter will not result in an error but the new value will not be applied.

Note - The current firmware version does not allow the following parameters to be

configured:

o Receive ACC Map o Transmit ACC Map o Magic Number o FCS Size

Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

PPP Link Quality Report

LQR Info

Displays Link Quality Report information for a particular PPP link.

PN 613-50507-00 Rev D Page 96 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - The LQR Info sub-menu option does not display the correct parameters.

Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.

LQR Configuration

Displays Link Quality Report configuration information for a particular PPP link.

Note - The LQR Configuration sub-menu option does not display the correct

parameters. Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.

LQR Extensions

Displays information on the most recently received Link Quality Report packet for a particular PPP link.

Note - The LQR Extensions sub-menu option does not display the correct parameters.

Instead, it displays the sub-menu option name as a parameter with a value of 'noSuchName'.

PPP Tests

Performs a PPP echo test or PPP discard test.

Note - The PPP Tests sub-menu option does not display the correct parameters. Instead, it

displays the sub-menu option name as a parameter with a value of 'noSuchName'.

MAC Bridging over PPP

Bridging Info

Displays information indicating whether the Bridge Network Control Protocol has reached an opened state, the type of compression used, and use of LAN identification field in packets.

Bridging Configuration Info

Displays bridging configuration information for a particular PPP link.

Note - The current firmware version does not allow the Administration Status

parameter to be configured. Attempting to configure this parameter will not result in an error but the new value will not be applied.

Note - The current firmware version does not allow the following parameters to be

configured:

 Tinygram  Ring ID

PN 613-50507-00 Rev D Page 97 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

 Line ID  LAN ID

Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Bridge Media Status

Diplays the types of MAC frames that can be sent or received across each of the system's interfaces.

Bridge Media Configuration

Displays configuration information used to negotiate the MAC types to be sent or received.

Note - The current firmware version does not allow the Local Status parameter to be

configured. Attempting to configure this parameter will not result in an error but the new value will not be applied.

IP over PPP

IP Info

Displays IP compression protocol status information for a particular PPP link.

IP Configuration Info

Displays IP compression protocol configuration information for a particular PPP link.

Note - The current firmware version does not allow the Compression parameter to be

configured. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: noSuchName."

Note - The current firmware version does not allow the Administration Status

parameter to be configured. Attempting to configure this parameter will not result in an error but the new value will not be applied.

PPP Security

Security Configuration Info

Displays the security configuration information for a particular PPP link.

Note - The current firmware version does not allow the Protocol parameter to be

configured. Attempting to configure this parameter will not result in an error but the new value will not be applied.

PN 613-50507-00 Rev D Page 98 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - The current firmware version does not allow the Status parameter to be

configured. Attempting to configure this parameter will result in the error message: "The error occurred with 'Set' operation. Error: noSuchName."

Security Secrets

Displays information on the identities and secrets used by the PPP authentication protocols.

Note -The current firmware version does not allow the Protocol parameter to be

configured. Attempting to configure this parameter will not result in an error but the new value will not be applied.

Note - Setting the Status parameter to 'invalid' clears the corresponding values of the

Identity and Secret parameters.

Note - AT-View Plus Device Manager allows the user to enter up to 63 characters for

the Identity and Secret parameters. Entering more than 63 characters will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Note - Security Secrets parameters return to their default values whenever the device

is restarted.

Port Menu

From the Port menu, you can view and edit MIB information about selected ports.

Interface Info

Displays port statistics such as the number of frames received and transmitted on the port, bytes received and transmitted on the port, and port status.

Note - The Interface Info sub-menu option displays port parameters for 20 ports. By default,

the Administration Status parameter is set to 'up' for the first four ports and 'down' for the rest of the ports. For ports 1 to 3, the Administration Status parameter cannot be configured. Its value is fixed to 'up'. For ports 5 to 12, valid MIB Set values for the Administration Status parameter are 'up' and 'down'. Attempting to set this parameter to any other value will result in the error message: "The error occurred with 'Set' operation. Error: bad value."

Note - The Administration Status parameter always returns to its default value whenever the

device is restarted.

Error Statistics

Displays error statistics for the port.

PN 613-50507-00 Rev D Page 99 of 253

Allied Telesyn AT-VIEW PLUS

DEVICE MANAGEMENT

Note - The current firmware version returns 'noSuchName' for the Ethernet Chip Set

parameter.

AT-AR200E

PN 613-50507-00 Rev D Page 100 of 253

Allied Telesis AT-VIEW PLUS 2.4 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Basic Operations

Common operations on the main window

Menu for stacked devices

Port selection dialog box

Port status colors

LED status

Utilization

AT-8000 Series

Main Window

Agent Menu

Bridge Menu

RMON Menu

Port Menu

Stacking Menu

Expansion Module Notes

AT-8124

Main Window

Agent Menu

Bridge Menu

RMON Menu

Port Menu

AT-8124XL (V2)

Main Window

Agent Menu

Bridge Menu

RMON Menu

Port Menu

AT-8200XL Series

Main Window

Agent Menu

Bridge Menu

RMON Menu

Port Menu

Expansion Module Notes

AT-8324

Main Window

Agent Menu

Bridge Menu

RMON Menu

Port Menu

Stacking Menu

AT-8324SX

Main Window

Agent Menu

Bridge Menu

RMON Menu

Port Menu

Stacking Menu

AT-8300GB Series

Main Window

Agent Menu

Bridge Menu

RMON Menu

Port Menu

Stacking Menu

AT-8400

Main Window

Agent Menu

Bridge Menu

RMON Menu

Port Menu

Stacking Menu

AT-8400 Line Cards

AT-8411

AT-8412

AT-8413

AT-8414

AT-9006 Family

Main Window

Agent Menu

Bridge Menu

RMON Menu

VLAN Menu

Port Menu

AT-9410GB

Main Window