Allied Telesis AT-FS217 User Manual

AT-FS211
AT-FS212
AT-FS212/1
AT-FS212/2
AT-FS212/3
AT-FS212/4
AT-FS214
AT-FS215
AT-FS216
AT-FS217

Wall-Mountable Fast Ethernet Switches

PN 613-50226-00 Rev B

Installation Guide

Copyright  2001 Allied Telesyn International Corp.
960 Stewart Drive, Suite B, Sunnyvale CA 94085 USA

All rights reserved. No part of this publication may be reproduced without prior
written permission from Allied Telesyn International Corp.

Ethernet is a registered trademark of Xerox Corporation. All other product names,
company names, logos or other designations mentioned herein are trademarks or
registered trademarks of their respective owners.

Allied Telesyn International Corp. reserves the right to make changes in specifications
and other information contained in this document without prior written notice. The
information provided herein is subject to change without notice. In no event shall
Allied Telesyn International Corp. be liable for any incidental, special, indirect, or
consequential damages whatsoever, including but not limited to lost profits, arising out
of or related to this manual or the information contained herein, even if Allied Telesyn
International Corp. has been advised of, known, or should have known, the possibility of
such damages.

Safety Warnings

Standards: This product meets the following standards.

DECLARATION OF CONFORMITY
Manufacture Name: Allied Telesyn International Corp.
Manufacture Address: 960 Stewart Drive, Suite B

Manufacture Telephone: [phone]
Declares that the product: Fast Ethernet Switches
Model Numbers: AT-FS211, AT-FS212, AT-FS212/1,

This product complies with FCC Part 15B, Class B Limits:
This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device must not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class B

digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on. The
user is encouraged to try to correct the interference by one or more of the following
measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Changes and modifications not expressly approved by the manufacturer or registrant of
this equipment can void your authority to operate this equipment under Federal
Communications Commission rules.

U.S. Federal Communications Commission

Sunnyvale, CA 94085 USA

AT-FS212/2, AT-FS212/3, AT-FS212/4,
AT-FS214, AT-FS215, AT-FS216,
AT-FS217

Industry Canada

This Class B digital apparatus meets all requirements of the Canadian Interference­Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur
le matériel brouilleur du Canada.

RFI Emission EN55022 Class B
Warning: In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.
Immunity EN55024

$ 1

$ 2

$ 3

iii

Safety Wa rnings

Warning: This product requires shielded cables to comply with emission and immunity
standards. If it is used with unshielded cables, the user may be required to take measures
to correct the interference problem at their own expense.

Electrical Safety EN60950 (TUV), UL1950 (UL/cUL)
Laser EN60825
Warning Class 1 Laser product. (AT-FS212/x models)
Warning Do not stare into the Laser beam.

At time of installation, the Fiber Optic Lasers comply with FDA Radiation Performance
Standard 21CFR Subchapter J, applicable at date of manufacture.

This is a “CLASS 1 LED PRODUCT” (AT-FS21x models)

Important: Appendix B contains translated safety statements for installing this
equipment. When you see the
your language.

Wichtig: Anhang B enthält übersetzte Sicherheitshinweise für die Installation dieses
Geräts. Wenn Sie
in Ihrer Sprache nach.

Vigtigt: Tillæg B indeholder oversatte sikkerhedsadvarsler, der vedrører installation af
dette udstyr. Når De ser symbolet
sikkerhedsadvarsler i Deres eget sprog.

Belangrijk: Appendix B bevat vertaalde veiligheidsopmerkingen voor het installeren van
deze apparatuur. Wanneer u de
veiligheidsinstructies in uw taal.

Important: L'annexe B contient les instructions de sécurité relatives à l'installation d e cet
équipement. Lorsque vous voyez le symbole

la traduction de ces instructions dans votre langue.
Tärkeää: Liite B sisältää tämän laitteen asentamiseen liittyvät käännetyt turvaohjeet.

Kun näet
Importante: l’Appendice B contiene avvisi di sicurezza tradotti per l’installazione di

questa apparecchiatura. Il simbolo
sicurezza nella propria lingua.

Viktig: Tillegg B inneholder oversatt sikkerhetsinformasjon for installering av dette
utstyret. Når du ser
sikkerhetsinformasjonen på ønsket språk.

Importante: O Anexo B contém advertências de segurança traduzidas para instalar este
equipamento. Quando vir o símbolo
idioma no Anexo B.

Importante: El Apéndice B contiene mensajes de seguridad traducidos para la
instalación de este equipo. Cuando vea el símbolo
mensaje de seguridad traducido a su idioma.

Obs! Bilaga B innehåller översatta säkerhetsmeddelanden avseende installationen av
denna utrustning. När du ser
säkerhetsmeddelandet på ditt språk.

$ 4

$ 6

$ 7

$ 8

$ 9

$

, go to Appendix B for the translated safety statement in

$

sehen, schlagen Sie in Anhang B den übersetzten Sicherheitshinweis

$

, skal De slå op i tillæg B og finde de oversatte

$

ziet, raadpleeg Appendix B voor vertaalde

$

, reportez-vous à l'annexe B pour consulter

$

-symbolin, katso käännettyä turvaohjetta liitteestä B.

$

, indica di consultare l’Appendice B per l’avviso di

$

, åpner du til Tillegg B for å finne den oversatte

$

, leia a advertência de segurança traduzida no seu

$

, vaya al Apéndice B para ver el

$

, skall du gå till Bilaga B för att läsa det översatta

$ 5

iv

Table of Contents

Safety Warnings ............................................................................................iii

Welcome to Allied Telesyn .........................................................................vii

Where to Find Web-based Guides ...................................................................vii

Document Conventions ....................................................................................vii

Contacting Allied Telesyn...............................................................................viii

Online Support .........................................................................................viii

Technical and Fax Support......................................................................viii

Technical Support E-mail Addresses ........................................................ix

Returning Products ........................................................................................... ix

FTP Server.........................................................................................................ix

For Sales or Corporate Information ..................................................................x

Tell Us What You Think .................................................................................... x

Chapter 1

Overview ..........................................................................................................1

Key Features.......................................................................................................3

Switch Performance .................................................................................... 3

Status LEDs ................................................................................................ 4

External Power Adapter .............................................................................4

Auto MDI/MDI-X.........................................................................................4

Functional Description....................................................................................... 5

Frame Processing........................................................................................ 5

Address Recognition and Filtering.............................................................5

Network Topologies............................................................................................6

Chapter 2

Installing the Switch ..................................................................................... 7

Verifying the Package Contents ........................................................................7

Planning the Installation...................................................................................7

Selecting a Site ...................................................................................................9

Reviewing Safety Guidelines .............................................................................9

Installing the Switch........................................................................................10

Warranty Registration.....................................................................................13

v

Chapter 3

Troubleshooting ...........................................................................................15

Appendix A

Technical Specifications ............................................................................17

Specifications ....................................................................................................17

Physical......................................................................................................17

Temperature ..............................................................................................17

Electrical and Mechanical Specifications.................................................17

Electrical Rating........................................................................................18

Fiber Optic Port Specifications ........................................................................18

Pinout Assignments..........................................................................................20

Appendix B

Electrical Safety and Installation Requirements .................................21

Appendix C

Technical Support Fax Order ...................................................................33

Incident Summary............................................................................................33

vi

Welcome to Allied Telesyn

This installation guide contains instructions on how to wall-mount the
AT-FS21x and the AT-FS212/x Series Fast Ethernet Switches and how to
connect the units to your network.

Where to Find Web-based Guides

The Allied Telesyn web site at www.alliedtelesyn.com provides you with an
easy way to access the most recent documentation, software, and technical
information for all of our products. For product guides, you can go directly to
the following web page: www.alliedtelesyn.com/support/prd_libs.htm.

Document Conventions

This guide uses several conventions that you should become familiar with
before you begin to install the product.

Note

A note provides additional information.

Caution

A caution indicates that performing or omitting a specific action may
result in equipment damage or loss of data.

Warning

A warning indicates that performing or omitting a specific action may
result in bodily injury.

vii

Welcome to Allied Telesyn

Contacting Allied Telesyn

You can contact Allied Teleysn technical support online or by telephone, fax,
or e-mail.

Online Support

You can request technical support online by filling out the Online Technical
Support Form at www.alliedtelesyn.com/support/supportf.asp or by
accessing the Technical Support Knowledge Base from Allied Telesyn’s North
American web site. You can use the Knowledge Base to submit questions to
our technical support staff and review answers to previously asked questions.

Technical and Fax Support

For technical support via fax, please fill out the “Technical Support Fax
Order” on page 33 and send it to the appropriate location listed below.

Americas

United States, Canada, Mexico,
Central America, South America
Tel: [phone], option 4
Fax: [phone]

Asia

Singapore, Taiwan, Thailand, Malaysia,
Indonesia, Korea, Philippines, China,
India, Hong Kong
Tel: [phone]
Fax: [phone]

Australia

Australia, New Zealand
Tel: [phone]
Fax: [phone]

France

France, Belgium, Luxembourg,
The Netherlands, Middle East, Africa
Tel: [phone]
Fax: [phone]

Germany

Germany, Switzerland, Austria, Eastern
Europe
Tel: [phone]
Fax: [phone]

Italy

Italy, Spain, Portugal, Greece, Turkey,
Israe

l

Tel: [phone]
Fax: [phone]

Japan

Tel: [phone]
Fax: [phone]

United Kingdom

United Kingdom, Denmark, Norway,
Sweden, Finland
Tel: [phone]
Fax: [phone]

viii

AT-FS21x and AT-FS212/x Series In st al l a tion G ui de

Technical Support E-mail Addresses

United States and Canada

[e-mail]

Latin America, Mexico, Puerto Rico, Caribbean, and Virgin Islands

[e-mail]

Europe

[e-mail]

Returning Products

Products for return or repair must first be assigned a Return Materials
Authorization (RMA) number. A product sent to Allied Telesyn without a
RMA number will be returned to the sender at the sender’s expense.

To obtain an RMA number, contact Allied Telesyn’s Technical Support at one
the following locations:

North America

Toll-free: 1-800-428-4835, option 4
Fax: [phone]

Latin America, the Caribbean, and
Virgin Islands

Tel: international code + 425-481-3852
Fax: international code + 425-481-3895

Mexico

Toll-free: 800-424-5012, ext 3852
Fax: international code + 425-481-3895

Australia

Toll-free: 1-800-000-880
Fax: [phone]

Europe, Africa, and the Middle East

Tel: [phone]
Fax: [phone]

Puerto Rico

Tel: [phone], ext 3852 or
1-800-424-4284, ext 385

Asia and Southeast Asia

Tel: [phone]
Fax: [phone]

New Zealand

Toll-free: 0800-45-5782

2

FTP Server

If you need management software for an Allied Telesyn device and you know
the file name of the software, you can download the software by connecting
directly to our FTP server at ftp.alliedtelesyn.com. At login, enter
‘anonymous’ as the user name and your e-mail address for the password.

ix

Welcome to Allied Telesyn

For Sales or Corporate Information

You can contact Allied Telesyn for sales or corporate information at one of the
locations below:

Allied Telesyn International Corp.

19800 North Creek Parkway, Suite 200
Bothell, WA 98011
Tel: [phone]
Fax: [phone]

Allied Telesyn International Corp.

960 Stewart Drive, Suite B
Sunnyvale, CA 94085
Tel: [phone] (US and Canada)
Fax: [phone]

Tell Us What You Think

If you have any comments or suggestions on how we might improve this or
other Allied Telesyn documents, please fill out the Send Us Feedback Form at
www.alliedtelesyn.com/contact/feedbackf.asp.

x

Chapter 1

Overview

The AT-FS21x and AT-FS212/x Series Fast Ethernet Switches feature the
following models:

❑ AT-FS211 ❑ AT-FS212/4
❑ AT-FS212 ❑ AT-FS214
❑ AT-FS212/1 ❑ AT-FS215
❑ AT-FS212/2 ❑ AT-FS216
❑ AT-FS212/3 ❑ AT-FS217

These switches are designed to interconnect LAN devices and subnetworks
over large distances. These dual-port switches can also improve the
performance of your network by dividing it into smaller, more manageable
segments.

The AT-FS21x and AT-FS212/x Series Switches have a 10/100Base-TX
twisted pair port and a 100Base-FX fiber optic port. The twisted pair port has
an RJ-45 connector and a maximum operating distance of 100 meters (328
feet). This port operates at 10/100 Mbps and features half- and full-duplex
operation.

The fiber optic port has a FJ, LC, MT-RJ, SC, ST, or VF-45 connector and a
maximum operating distance 2 kilometers (1.2 miles) to 100 kilometers
(62 miles), depending on the model. This port operates at 100 Mbps and
features full-duplex operation.

1

Overview

These switches are easy to install and do not require software configuration or
management. Figure 1 illustrates an AT-FS21x Series Switch.

Mounting
Bracket Screws

4

1

2

S

F

-

T

A

Fast Ethernet Switch

LEDs

X

F

R

W

P

X

T

10Base-T/
100Base-TX

C

D

V

.3

3

Cable Hook

DC Connector10/100Base-TX Port

Figure 1 AT-FS21x Series Switch (Model AT-FS214)

Table 1 lists the operating distances for the AT-FS21x and AT-FS212/x Series
Switches.

Table 1 Maximum Operating Distance

Model 10/100Base-TX

Connector Maximum

Operating Distance

1

100Base-FX

Connector Maximum

Operating Distance

2

AT-FS211 RJ-45 100 m (328 ft) ST 2 km (1.2 mi)
AT-FS212 RJ-45 100 m (328 ft) SC 2 km (1.2 mi)
AT-FS212/1 RJ-45 100 m (328 ft) SC 15 km (9.3 mi)
AT-FS212/2 RJ-45 100 m (328 ft) SC 40 km (24.8 mi)
AT-FS212/3 RJ-45 100 m (328 ft) SC 70 km (43.4 mi)
AT-FS212/4 RJ-45 100 m (328 ft) SC 100 km (62 mi)
AT-FS214 RJ-45 100 m (328 ft) MT-RJ 2 km (1.2 mi)
AT-FS215 RJ-45 100 m (328 ft) VF-45 2 km (1.2 mi)
AT-FS216 RJ-45 100 m (328 ft) LC 2 km (1.2 mi)
AT-FS217 RJ-45 100 m (328 ft) FJ 2 km (1.2 mi)

1. Maximum distance can only be obtained when the UTP/STP cabling is installed and verified to the TIA/EIA 568A

Commercial Building Telecommunications Cabling Standard.

2. Maximum distance for 100 Mbps Optical Datalinks are dependent on the following factors: type of optical fiber,

duplex mode of both end-nodes, and maximum optical loss budget for each of the optical fiber at the operating
optical wavelength.

2

AT-FS21x and AT-FS212/x Series In st al l a tion G ui de

Key Features

The switches have the following key features:

❑ LEDs for unit and port status

❑ Wall-mountable chassis

❑ Auto MDI/MDI-X

❑ External AC/DC power adapters (North America, Continental, or

Europe)

❑ Full- or half-duplex mode operation on the twisted pair port

❑ Full-duplex operation on the fiber optic port

❑ FJ, LC, MT-RJ, SC, ST, or VF-45 fiber optic connector

❑ Data packet forwarding and filtering at full wire speed

❑ Store and forward switching mode

❑ Automatic address learning and aging

❑ IEEE 802.3u compliant auto-negotiation on the twisted pair port

Switch Performance

The switches perform at:

❑ 148,800 pps for 100 Mbps and 14,880 pps for 10 Mbps with full wire

speed forwarding and filtering

❑ 200 Mbps maximum throughput in 100 Mbps, full-duplex mode

❑ 20 Mbps maximum throughput in 10 Mbps, full-duplex mode

❑ Storage for up to 4,000 MAC addresses

❑ Unlimited multicast/broadcast addresses

❑ Low latency 15.6 µs (64-byte packet, 100 Mbps full-duplex)

3

Overview

Status LEDs

Table 2 lists the switch LEDs.

Table 2 AT-FS21x and AT-FS212/x Series Switch LEDs

LED Color Description

PWR Green Power is applied.
FX Green

Blinking

TX Green

Blinking

100M Green

OFF

A link has been established on the fiber optic port
Activity has been detect ed on the fiber optic port.

A link has been establ ished on the twisted pair port
Activity has been detected on the twisted pair port.

The twisted pair port is operating at 100 Mbps.
The twisted pair port is operating at 10 Mbps.

External Pow er Adapter

The power adapter supplies 3.3V DC to the switch. Allied Telesyn supplies an
approved safety compliant AC power adapter for 3.3 V/1.5 A versions with an
unregulated output of 3.3V DC.

Auto MDI/MDI-X

An RJ-45 twisted pair port on a 10 Mbps or 100 Mbps Ethernet network
device can have one of two possible wiring configurations: MDI or MDI-X. The
RJ-45 port on a PC, router, or bridge is typically wired as MDI, while the
twisted pair port on a switch or hub is usually MDI-X.

To connect two 10 Mbps or 100 Mbps network devices together that have
dissimilar port wiring configurations, such as MDI to MDI-X, you use a
straight-through twisted pair cable. To connect two network devices that have
the same wiring configuration, such as MDI to MDI, you use a crossover cable.

The AT-FS21x and AT-FS212/x Series Switches feature automatic MDI/
MDI-X. Each port automatically determines the configuration of the port on
the device to which it is connected and then configures itself appropriately.
For example, if a port on a switch is connected to a port on a bridge, which is
typically wired as MDI, the port on the switch automatically configures itself
as MDI-X. This eliminated the need for using a crossover cable with these
switches.

4

AT-FS21x and AT-FS212/x Series In st al l a tion G ui de

Functional Description

Frame Process ing

The switches support store and forward switching at Fast Ethernet full-wire
speed in 10 or 100 Mbps, half- or full-duplex mode. Packets entering each port
are stored in buffers. After the full packet is received, it is forwarded or
discarded depending on its destination address and error status. This ensures
that only error-free data packets destined for another segment will be
transferred across the switch, reducing network load. For example, if the
packet entering from Port 1 is destined for an end station on Port 2, it will be
forwarded if the Frame Check Sequence (FCS) is valid. If the packet from Port
1 is destined for an end station also attached to Port 1, then the packet is
discarded.

The switch will discard CRC error, misaligned, runt, and under-sized/over­sized packets. When the packet has dribble bits at the end, the switch will
truncate to octet boundary and check for a good FCS before forwarding.

Address Recognition and Filtering

Up to 4,000 MAC addresses can be stored in the MAC address table. The
switch will learn all new addresses in real-time after power-up with its
address self-learning mechanism. If the source address of an incoming packet
is not found in the address table, the switch waits until the end of the packet
to check for good CRC and then updates its MAC address table. Because the
switch has Automatic Address Aging, if a source address entry in the table is
not updated within five minutes, the entry is deleted from the table. The
switch forwards multicast, broadcast, and unicast packets when the MAC
address table size is exceeded.

5

Overview

Network Topologies

Figure 2 illustrates a topology using one AT-FS214 switch to interconnect two
small networks of stackable hubs. Network 1 has an AT-FH812u with an
AT-FH807u switching module connected to the 100Base-FX port on the
AT-FS214. Network 2 has an AT-3624TR hub connected to the 10/100Base-TX
port on the AT-FS214.

Network 1

Network 2

AT-FH812u
with an
AT-FH807u
module

AT-FH812u

AT-FH812u

Twisted Pair
Fiber Optic

AT-FS214

AT-FS214

Fast Ethernet Switch

FX

PWR

TX

100MLK/AT

Figure 2 Network Topology

AT-3624TR

AT-3624TR

AT-3624TR

6

Chapter 2

Installing the Switch

Verifying the Package Contents

Make sure the following items are included in your package. If any item is
missing or damaged, contact your Allied Telesyn sales representative for
assistance.

❑ One AT-FS21x or AT-FS212/x Series Fast Ethernet Switch

❑ External power adapter (North America, Continental Europe, or

United Kingdom)

❑ 2 Phillips-head screws

❑ 2 plastic anchors

❑ Cable tie

❑ This installation guide

❑ Warranty card

Planning the Installation

Be sure to observe the following guidelines when planning the installation of
your switch.

❑ The end-node connected to the fiber optic port on the switch must be

able to operate at 100 Mbps and full-duplex mode.

❑ The end-node connected to the twisted pair port can operate at either

10 Mbps or 100 Mbps, half- or full-duplex mode.

❑ The twisted pair cabling must be kept away from sources of electrical

noise, such as radios, transmitters, power lines, broadband amplifiers,
electrical motor, and fluorescent fixtures.

❑ Refer to the following tables for the cabling specifications for the 10/

100Base-TX and 100Base-FX ports.

7

Installing the S witch

Table 3 10/100Base-TX Twisted Pair Port Cabling Specifications

Operating Mode Twisted Pair Cable

Maximum Operating
Distance

10Base-T Shielded or unshielded Category 3 or be tter 100 m (328 ft)
100Base-TX Shielded or unshielded Category 5 or better 100 m (328 ft)7

Table 4 100Base-FX Fiber Optic Port Cabling Specificatio ns (Full-duplex)

Model Fiber Optic Cable

AT-FS211 50/125 or 62.5/125

Maximum
Operating Di stance

2 km (1.2 mi) 13 dB at 1310 nm

Maximum Allowable
Loss Budget

micron multimode

AT-FS212 50/125 or 62.5/125

2 km (1.2 mi) 13 dB at 1310 nm

micron multimode

AT-FS212/1 9/125 micron

15 km (9.3 mi) 16 dB at 1310 nm

single-mode

AT-FS212/2 9/125 micron

40 km (24.8 mi) 30 dB at 1310 nm

single-mode

AT-FS212/3 9/125 micron

70 km (43.4 mi) 33 dB at 1310 nm

single-mode

AT-FS212/4

1

9/125 micron

100 km (62 mi) 34 dB at 1550 nm

single-mode

AT-FS214 50/125 or 62.5/125

2 km (1.2 mi) 13 dB at 1310 nm

micron multimode

AT-FS215 50/125 or 62.5/125

2 km (1.2 mi) 13 dB at 1310 nm

micron multimode

AT-FS216 50/125 or 62.5/125

2 km (1.2 mi) 13 dB at 1310 nm

micron multimode

AT-FS217 50/125 or 62.5/125

2 km (1.2 mi) 13 dB at 1310 nm

micron multimode

1. The cable must be non-dispersion-shifted, dispersion-shifted, or non-zero dispersion-shifted single-mode fiber

optic cable.

8

AT-FS21x and AT-FS212/x Series In st al l a tion G ui de

Note

Refer to page 18 for additional fiber optic port specifications.

Selecting a Site

Be sure to observe the following requirements when choosing a site for your
switch.

❑ Select a site that is dust-free and moisture-free.

❑ Be sure that the site will allow you to easily access the fiber optic and

twisted pair cables and the power cord.

❑ Use dedicated power circuits or power conditioners to supply reliable

power to the device.

Reviewing Safety Guidelines

Please review the following safety guidelines before you begin to install the
media converter.

Warning

Class 1 laser device. $ 7

Warning

Do not stare into the laser beam. $ 8

Warning

Electric Shock Hazard: To prevent electric shock, do not remove the
cover. There are no user-serviceable parts inside. The unit contains
hazardous voltages and should only be opened by a trained and
qualified technician. $ 9

Warning

Lightning Danger: Do not work on this equipment or cables during
periods of lightning activity. $ 11

Caution

Power cord is used as a disconnection device: To de-energize
equipment, disconnect the power cord. $ 12

9

Installing the S witch

Caution

Pluggable Equipment: The socket outlet should be installed near the
equipment and should be easily accessible. $ 13

Caution

Air vents: The air vents must not be blocked on the unit and must have
free access to the room ambient air for cooling. $ 14

Caution

Operating Temperature: This product is designed for a maximum
ambient temperature of 40°C. $ 16

Caution

All Countries: Install this product in accordance with local and
National Electric Codes. $ 17

Installing the Switch

To install an AT-FS21x or AT-FS212/x Series Switch, perform the following
procedure:

1. Remove all equipment from the package and store the packaging in a safe

place.

2. Remove the mounting bracket screws, as shown in Figure 3. These screws

are marked with black circles.

h

itc

w

t S

e

n

r

e

th

AT-FS214

t E

s

a

F

PWR

FX

TX

10Base-T/
100Base-TX

C

D

V

.3

3

Figure 3 Removing the Moun ting Bracket Screws

10

AT-FS21x and AT-FS212/x Series In st al l a tion G ui de

3. Gently slide the bracket off the switch. See Figure 4.

Figure 4 Sliding the Wall-mounting Bracket of f t he Switch

Note

For drywall installation, drill two 3/16-inch holes, insert the plastic
anchors and tap flush.

4. Position the wall-mounting bracket on the wall and, using two

Phillips-head screws (provided), secure the bracket to the wall. See Figure

5.

Figure 5 Attaching the Wall-mounting Bracket to the Wall

11

Installing the S witch

Note

The switch can be mounted either vertically or horizontally.

5. Using the flanges under the fiber optic port as a guide, slide the switch

into the mounting bracket. Refer to Figure 6.

Flange Flange

AT-FS214

Fast Ethernet S

witch

F

X

P

W

R

T

X
L

K

/

A

T

1

0

0

M

Figure 6 Sliding the Switch Over the Wall-mounting Bracket

6. Secure the switch to the wall-mounting bracket using the screws removed

in Step 2.

7. If your switch is shipped with Universal Voltage Power Adapter (2-cable),

do the following:

a. Connect the AC power cord to the Universal Voltage Power Adapter.

b. Plug the DC cable into the DC receptacle on the switch.

c. Plug the AC power cord on the adapter to a power outlet.

12

AT-FS21x and AT-FS212/x Series In st al l a tion G ui de

8. If your switch is shipped with an Single Voltage Power Adapter (single

cable), do the following:

a. Plug the DC cable into the DC receptacle on the switch.

b. Plug the AC power cord to a power outlet.

Note

To prevent the DC power cable from being inadvertently pulled out of
the switch, use the cable tie supplied with the unit to secure the DC
power cable to the cable hook located next to the DC connector.

9. Verify that the PWR LED on the switch is green. If the LED is OFF, refer

to “Troubleshooting” on page 15.

10. Remove the dust cover from the 100Base-FX fiber optic port and connect

the fiber optic cable.

11. Connect the twisted pair cable to the 10/100Base-TX port.

12. Power ON the end-nodes. The TX and FX LEDs should be green. If the

LEDs are OFF, refer to “Troubleshooting” on page 15.

13. The switch is now ready for use.

Warranty Registration

When you finish installing the product, you should register your product by
completing the enclosed warranty card and sending it in. You can also fill out
the registration online at www.alliedtelesyn.com/support/warrantyf.asp.

13

Chapter 3

Troubleshooting

Follow the guidelines below to test and troubleshoot the installation in the
event a problem occurs.

If the PWR LED is OFF, do the following:

❑ Make sure that the power adapter is securely connected to a power

source and the DC power cord on the adapter is securely connected to
the DC power connector on the switch.

❑ Verify that the power outlet has power by connecting another device

to it.

❑ Try connecting the switch to another power source.

❑ Try using another power adapter.

If the TX LED for the twisted pair port is powered OFF, do the following:

❑ Check that the end-node connected to the port is ON and is operating

properly.

❑ Check that the twisted pair cable is securely connected to the twisted

pair port on the switch and on the end-node.

❑ Make sure that the twisted pair cable does not exceed 100 meters (328

feet).

❑ If the end-node is operating at 100 Mbps, verify that you are using

Category 5 or better twisted pair cabling.

If the FX LED for the fiber optic port is powered OFF, do the following:

❑ Verify that the end-node connected to the port is ON and is operating

properly.

❑ Check that the fiber optic cable is securely connected to the fiber optic

port on the switch and on the end-node.

15

Troubleshooting

❑ Check to be sure that the end-node connected to the port is operating

at 100 Mbps.

❑ Make sure that the fiber optic port on the end-node is operating in

full-duplex mode.

❑ Make sure that the cable connected to the fiber optic receiver port on

the switch is connected to the transmitter port on the remote end-node
and that the fiber optic transmitter port on the switch is connected to
the receiver port on the end-node.

❑ Test the attenuation on the fiber cable to ensure that it does not

exceed acceptable values.

❑ Verify that you are using the appropriate type of fiber optic cable and

that you have not exceeded the maximum operating distance. For
cable types and operating distances, refer to Table 4 on page 8.

❑ Check that the operating specifications of the fiber optic port on the

end-node are compatible with the operating specifications of the fiber
optic port on the switch. Refer to page 18 for the fiber optic port
specifications.

If you are still experiencing problems after testing and troubleshooting the
installation, contact Allied Telesyn Technical Support for assistance. Refer to
“Contacting Allied Telesyn” on page viii or visit our web site at
www.alliedtelesyn.com for support information.

16

Appendix A

Technical Specifications

Specifications

Physical

Dimensions: 90 mm x 24 mm x 70 mm

(3.54 in x 0.94 in x 2.76 in)

Weight: 0.23 kg (0.5 lbs)

Temperature

Operating: 0° to 40° C

Storage: -25° to 70° C

Relative Humidity: 5% to 80% (non-condensing)

Operating Altitude: Up to 10,000 feet

Electrical and Mechanical Specifications

Standard: CE Compliant IEEE 802.3, IEEE 802.3u

Immunity: Conforms to EN500082-1 1997 immunity

standard

Safety: Conforms to all standards normally supported

by Allied Telesyn products including safety
standards UL 1950 (UL/cUL), TUV EN60950,
EN60825 CE Compliant

EMI/RFI: Meets all applicable requirements for emissions

including but not limited to FCC Class A,
EN55022 Class A

17

Technical Specifications

Electrical Rating

Input Supply Voltage 3.3V DC

Minimum Current Rating 1.5A

Maximum Power

Consumption 6W

Fiber Optic Port Specifications

The following tables list the specifications for the 100Base-FX fiber optic port.

Table 5 Fiber Optic Transmi tter

2

Model

AT-FS211

Fiber
Type

1

Fiber
Optic
Diameter

Optical
Frequency

Maximum A verage Minimum

Launch Power

MMF 50/125 1310 nm -14.0 -20.3 -22.5
AT-FS212
AT-FS214

MMF 62.5/125 1310 nm -14.0 -16.8 -19.0
AT-FS215

AT-FS216
AT-FS217

AT-FS212/1 SMF 9/125 1310 nm -8.0 -11.5 -15.0
AT-FS212/2 SMF 9/125 1310 nm 0.0 -3.0 -5.0
AT-FS212/3 SMF 9/125 1310 nm 0.0 -2.0 -4.0

3

AT-FS212/4

1. MMF = Multimode Fiber / SMF = Single-mode Fiber.

2. The launch power is measured at one meter from the transmitter.

3. The cable must be non-dispersion-shifted, dispersion-shifted, or non-zero dispersion-shifted single-mode fiber
optic cable.

SMF 9/125 1550 nm 0.0 -1.5 -3.0

18

AT-FS21x and AT-FS212/x Series In st al l a tion G ui de

Table 6 Fiber Optic Receiver

Receiver Power

Typical
Sensitivity

Model

AT-FS211

Fiber
Type

1

Fiber
Optic
Diameter

Optical
Frequency

Minimum

MMF 50/125 1310 nm -31.8 -34.5 -14.0
AT-FS212
AT-FS214

MMF 62.5/125 1310 nm -31.8 -34.5 -14.0
AT-FS215

AT-FS216
AT-FS217

AT-FS212/1 SMF 9/125 1310 nm -31.0 -31.0 -8.0
AT-FS212/2 SMF 9/125 1310 nm -35.0 -38.0 0.0
AT-FS212/3 SMF 9/125 1310 nm -37.0 -37.0 -3.0
AT-FS212/4 SMF 9/125 1550 nm -37.0 -37.0 -3.0

1. MMF = Multimode Fiber / SMF = Single-mode Fiber.

Table 7 Fiber Optic Dat alink

Model Fiber Type

Minimum
Power/Link
Budget

Average
Signal
Loss

Minimum
Operating
Distance

1

Maximum
Operating
Distance

Saturation

AT-FS211
AT-FS212

50/125
MMF

13.00 18.70 0 2 km (1.25 mi)

AT-FS214
AT-FS215
AT-FS216

62.5/125
MMF

16.80 22.50 0 2 km (1.25 mi)

AT-FS217
AT-FS212/ 1 9/125 SMF 16.00 19.50 0 15 km (9.4 mi)
AT-FS212/2 9/125 SMF 30.00 35.00 0 40 km (25 mi)
AT-FS212/ 3 9/125 SMF 33.00 35.00 15 km

(9.3 mi)

AT-FS212/ 4 9/125 SMF 34.00 35.00 40 km

(24.8 mi)

1. The recommended minimum range is stated in all cases where the maximum transmitter output power exceeds
the receivers saturation level. This is to prevent blinding or burning out of the optical receiver on the far end-node.

70 km
(43.4 mi)

100 km
(62 mi)

19

Technical Specifications

Table 8 Fiber Optic Loss Specification (Benchmarks)

Fiber Type

Multimode

Fiber Optic
Diameter

50/125 1310 nm 1.00 db/km 1.50 db/km 400

Optical
Frequency

Typical
Loss Factor

Worst Case
Loss Factor

Bandwidth

Fiber

62.5/125 1310 nm 1.00 db/km 1.5 db/km 500

Single-mode 9/125 nm 1310 nm 0.40 db/km 1 .00 db/km N/A

9/125 nm 1550 nm 0.30 db/km 0.75 db/km N/A

Pinout Assignments

Figure 7 shows the pin assignments of the switch’s 10/100Base-TX RJ-45 port.

Pin 1 Pin 8

Figure 7 RJ-45 Pin Assignments

Table 9 lists the RJ-45 connector pins and their signals for 10/100Base-TX.

Table 9 RJ-45 Pin Signals

MDI-X (Default) Signal MDI Signal

1RX+1 TX+
2RX-2 TX­3 TX+ 3 RX+
4- 4 ­5- 5 ­6 TX- 6 RX­7- 7 ­8- 8 -

20

Appendix B

Electrical Safety and Installation Requirements

Important: This appendix contains multiple-language translations for the
safety statements in this guide.

Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch
enthaltenen Sicherheitshinweise in mehreren Sprachen.

Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af
sikkerhedsadvarslerne i denne håndbog.

Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de
veiligheidsopmerkingen in deze gids.

Important: Cette annexe contient la traduction en plusieurs langues des
instructions de sécurité figurant dans ce guide.

Tärkeää: Tämä liite sisältää tässä oppaassa esiintyvät turvaohjeet usealla
kielellä.

Importante: questa appendice contiene traduzioni in più lingue degli avvisi
di sicurezza di questa guida.

Viktig: Dette tillegget inneholder oversettelser til flere språk av
sikkerhetsinformasjonen i denne veiledningen.

Importante: Este anexo contém traduções em vários idiomas das
advertências de segurança neste guia.

Importante: Este apéndice contiene traducciones en múltiples idiomas de los
mensajes de seguridad incluidos en esta guía.

Obs! Denna bilaga innehåller flerspråkiga översättningar av
säkerhetsmeddelandena i denna handledning.

21

Electrical Safety and Ins tallation Requiremen t s

Standards: This product meets the following standards.

U.S. Federal Communications Commission

DECLARATION OF CONFORMITY
Manufacture Name: Allied Telesyn International Corp.
Manufacture Address: 960 Stewart Drive, Suite B

Manufacture Telephone: [phone]
Declares that the product: Fast Ethernet Switches
Model Numbers: AT-FS211, AT-FS212, AT-FS212/1,

This product complies with FCC Part 15B, Class B Limits:
This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device must not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class B

digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on. The
user is encouraged to try to correct the interference by one or more of the following
measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Changes and modifications not expressly approved by the manufacturer or registrant of
this equipment can void your authority to operate this equipment under Federal
Communications Commission rules.

Sunnyvale, CA 94085 USA

AT-FS212/2, AT-FS212/3, AT-FS212/4,
AT-FS214, AT-FS215, AT-FS216,
AT-FS217

Industry Canada

This Class B digital apparatus meets all requirements of the Canadian Interference­Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur
le matériel brouilleur du Canada.

$ 1 RFI Emission EN55022 Class B

$ 2 Warning: In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

$ 3 Immunity EN55024

$ 4 Warning: This product requires shielded cables to comply with emission and

immunity standards. If it is used with unshielded cables, the user may be required
to take measures to correct the interference problem at their own expense.

$ 5 Electrical Safety EN60950 (TUV), UL1950 (UL/cUL)

$ 6Laser EN60825

SAFETY

22

AT-FS21x and AT-FS212/x Series In st al l a tion G ui de

$ 7 Warning Class 1 Laser product. (AT-FS212/x models)

$ 8 Warning Do not stare into the Laser beam.

At time of installation, the Fiber Optic Lasers comply with FDA Radiation
Performance Standard 21CFR Subchapter J, applicable at date of manufacture.

$ 9 ELECTRICAL NOTICES

Warning: ELECTRIC SHOCK HAZARD

To prevent ELECTRIC shock, do not remove the cover. No user­serviceable parts inside. This unit contains HAZARDOUS VOLTAGES
and should only be opened by a trained and qualified technician. To avoid
the possibility of ELECTRIC SHOCK, disconnect electric power to the
product before connecting or disconnecting the LAN cables.

$ 10 This is a “CLASS 1 LED PRODUCT” (AT-FS21x models)

$ 11 LIGHTNING DANGER

Danger: DO NOT WORK on equipment or CABLES during periods of LIGHTNING
ACTIVITY.

$ 12 Caution: Power cord is used as a disconnection device. to de-energize

equipment, disconnect the power cord.

$ 13 Pluggable equipment, the socket outlet shall be installed near the

equipment and shall be easily accessible.

$ 14 Caution: Air vents must not be blocked and must have free access to the room

ambient air for cooling.

$ 15 Power to the hub must be sourced only from the adapter.

USA/CANADA

Use a UL Listed/CSA Certified AC adapter of DC 3.3V, 1.5A.

EUROPE - EU

Use TÜV licensed AC adapter of DC 3.3V, 1.5A.

UK

Use a UK Safety Approved AC adapter of DC 3.3V, minimum 1.5A.

$ 16 Operating Temperature: This product is designed for a maximum ambient

temperature of 40 degrees C.

$ 17 All Countries: Install product in accordance with local and National Electrical

Codes.

Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.

$ 1Hochfrequenzstörung EN55022 Klasse B

$ 2 Warnung: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen

hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen
ergreifen.

$ 3Störsicherheit EN55024

$ 4 Achtung: Für dieses Produkt sind abgeschirmte Kabel erforderlich, damit den

Richtlinien für Emission und Interferenzschutz entsprochen wird. Falls das Produkt
mit nicht abgeschirmten Kabeln verwendet wird, können weitergehende
Maßnahmen für die Korrektur von Interferenzproblemen auf Kosten des Benutzers
notwendig werden.

$ 5 Elektrische Sicherheit EN60950 (TUV), UL1950 (UL/cUL)

$ 6Laser EN60825

23

Electrical Safety and Ins tallation Requiremen t s

SICHERHEIT

$ 7 Warnung Laserprodukt der Klasse 1.

$ 8 Warnung Nicht direkt in den Strahl blicken.
$ 9 Achtung: GEFÄHRLICHE SPANNUNG

Das Gehäuse nicht öffnen. Das Gerät enthält keine vom Benutzer
wartbaren Teile. Das Gerät steht unter Hochspannung und darf nur von
qualifiziertem technischem Personal geöffnet werden. Vor Anschluß der
LAN-Kabel, Gerät vom Netz trennen.

$ 10 Das ist ein “LED Produkt der Klasse 1”

$ 11 GEFAHR DURCH BLITZSCHLAG

Gefahr: Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters
ausführen.

$ 12 Vorsicht: Das netzkabel dient zum trennen der stromversorgung. Zur trennung

vom netz, kabel aus der steckdose ziehen.

$ 13 Steckbares Gerät: Die Anschlußbuchse sollte in der Nähe der Einrichtung

angebracht werden und leicht zugänglich sein."

$ 14 Vorsicht

Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum
Kühlen freien Zugang zur Raumluft haben

.

$ 15 Der Buchse darf nur aus dem Adapter Strom zugeführt werden.

EUROPE - EU

Gebrauchen Sie einen von TÜV zugelassenen Wechselstromadapter für Gleichstrom

3.3V, 1.5A.

$ 16 Betriebstemperatur

Dieses Produkt wurde für den Betrieb in einer Umgebungstemperatur von nicht
mehr als 40° C entworfen.

$ 17 Alle Länder: Installation muß örtlichen und nationalen elektrischen Vorschriften

entsprechen.

Standarder: Dette produkt tilfredsstiller de følgende standarder.

$ 1 Radiofrekvens

forstyrrelsesemission EN55022 Klasse B

$ 2 Advarsel: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse.

Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige
foranstaltninger.

$ 3 Immunitet EN55024

$ 4 Advarsel: Dette produkt skal bruges med afskærmede kabler for at overholde

bestemmelserne vedrørende udstråling og støjimmunitet. Hvis det bruges med
uafskærmede kabler, kan det blive påkrævet af brugeren at korrigere
interferensproblemer for egen regning.

$ 5 Elektrisk sikkerhed. EN60950 (TUV), UL1950 (UL/cUL)

$ 6Laser EN60825

SIKKERHED

$ 7 Advarsel Laserprodukt av klasse 1.

$ 8Advarsel Stirr ikke på strålen.

24

AT-FS21x and AT-FS212/x Series In st al l a tion G ui de

$ 9 ELEKTRISKE FORHOLDSREGLER

Advarsel: RISIKO FOR ELEKTRISK STØD

For at forebygge ELEKTRISK stød, undlad at åbne apparatet. Der er
ingen indre dele, der kan repareres af brugeren. Denne enhed indeholder
LIVSFARLIGE STRØMSPÆNDINGER og bør kun åbnes af en uddannet
og kvalificeret tekniker. For at undgå risiko for ELEKTRISK STØD,
afbrydes den elektriske strøm til produktet, før LAN-kablerne monteres
eller afmonteres.

$ 10 Dette er et “PRODUKT UNDER KLASSE 1 LED”

$ 11 FARE UNDER UVEJR

Fare: UNDLAD at arbejde på udstyr eller KABLER i perioder med
LYNAKTIVITET.

$ 12 Waarschuwing: Het toestel wordt uitgeschakeld door de stroomkabel te

ontkoppelen. Om het toestel stroomloos te maken: de stroomkabel ontkoppelen.

$ 13 Aan te sluiten apparatuur, de contactdoos wordt in de nabijheid van de apparatuur

geïnstalleerd en is gemakkelijk te bereiken."

$ 14 Opgelet: De ventilatiegaten mogen niet worden gesperd en moeten de

omgevingslucht ongehinderd toelaten voor afkoeling

$ 15 Strømforsyningen til apparatet må udelukkende tages fra

tilpasningstransformatoren.

EUROPE - EU

Brug kun TÜV godkendt vekselstrømstransformator på 3.3V jævnstrøm, 1.5A.

$ 16 Betjeningstemperatur: Dette apparat er konstrueret til en omgivende temperatur

på maksimum 40 grader C.

$ 17 Alle Lande: Installation af produktet skal ske i overensstemmelse med lokal og

national lovgivning for elektriske installationer.

Eisen: Dit product voldoet aan de volgende eisen.

$ 1 RFI Emissie EN55022 Klasse B

$ 2 Waarschuwing: Binnenshuis kan dit product radiostoring veroorzaken, in welk

geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen.

$ 3 Immuniteit EN55024

$ 4 Waarschuwing: Om te voldoen aan de emissie- en immuniteitsnormen dient dit

apparaat te zijn voorzien van afgeschermde kabels. Als het met niet-afgeschermde
kabels wordt gebruikt, kan het zijn dat de gebruiker maatregelen moet treffen om
interferentieproblemen voor eigen rekening op te lossen.

$ 5 Electrische Veiligheid EN60950 (TUV), UL1950 (UL/cUL)

$ 6Laser EN60825

VEILIGHEID

$ 7 Waarshuwing Klasse-1 laser produkt.

$ 8 Waarchuwing Neit in de straal staren.

$ 9 ELEKTRISKE FORHOLDSREGLER

Advarsel: RISIKO FOR ELEKTRISK STØD For at forebygge
ELEKTRISK stød, undlad at åbne apparatet. Der er ingen indre dele, der
kan repareres af brugeren. Denne enhed indeholder LIVSFARLIGE

25

Electrical Safety and Ins tallation Requiremen t s

STRØMSPÆNDINGER og bør kun åbnes af en uddannet og kvalificeret
tekniker. For at undgå risiko for ELEKTRISK STØD, afbrydes den
elektriske strøm til produktet, før LAN-kablerne monteres eller
afmonteres.

$ 10 Dit is een “KLASSE 1 LED-PRODUKT”

$ 11 GEVAAR VOOR BLIKSEMINSLAG

Gevaar: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.

$ 12 Attention: Le cordon d’alimentation sert de mise hors circuit. Pour couper

l’alimentation du matériel, débrancher le cordon.

$ 13 Equipement pour branchement electrique, la prise de sortie doit être placée près de

l’équipement et facilement accessible".

$ 14 Attention: Ne pas bloquer les fentes d’aération, ceci empêcherait l’air ambiant de

circuler librement pour le refroidissement

$ 15 Stroom mag alleen via de adapter naar het apparaat toegevoerd worden.

EUROPE - EU

Gebruik een door TÜV gekeurde wisselstroomadapter van 3.3 Volt gelijkstroom, 1.5
milliampères.

$ 16 Bedrijfstemperatuur: De omgevingstemperatuur voor dit produkt mag niet meer

bedragen dan 40 graden Celsius.

$ 17 Alle Landen: het toestel installeren overeenkomstig de lokale en nationale

elektrische voorschriften.

Normes: ce produit est conforme aux normes de suivantes.

$ 1 Emission d'interférences

radioélectriques EN55022 Classe

B

$ 2Mise En Garde: dans un environnement domestique, ce produit peut provoquer des

interférences radioélectriques. Auquel cas, l'utilisateur devra prendre les mesures
adéquates.

$ 3 Immunité EN55024

$ 4 Avertissement : Il faut utiliser des câbles blindés pour ce produit afin de respecter

les normes d’émission et d’immunité. Si l’utilisateur choisit d’utiliser des câbles non
blindés, il sera peut-être contraint de prendre les mesures nécessaires pour corriger
les problèmes d’interférences, ainsi que d’assumer le coût correspondant.

$ 5Sécurité électrique EN60950 (TUV), UL1950 (UL/cUL)

$ 6Laser EN60825

SÉCURITÉ

$ 7 Attention Producit laser di classe 1.

$ 8 Attention Ne pas fixer le faisceau des yeux.
$ 9 INFORMATION SUR LES RISQUES ÉLECTRIQUES

L

AVERTISSEMEN

Pour éviter toute ÉLECTROCUTION, ne pas ôter le revêtement
protecteur du matériel. Ce matériel ne contient aucun élément réparable
par l’utilisateur. Il comprend des TENSIONS DANGEREUSES et ne doit

: DANGER D’ÉLECTROCUTION

26

AT-FS21x and AT-FS212/x Series In st al l a tion G ui de

être ouvert que par un technicien dûment qualifié. Pour éviter tout risque
d’ÉLECTROCUTION, débrancher le matériel avant de connecter ou de
déconnecter les câbles LAN.

$ 10 Ce mat‚riel est un “PRODUIT A DIODE LECTROLUMINESCENTE DE CLASSE 1”

$ 11 DANGER DE FOUDRE

Danger: NE PAS MANIER le matériel ou les CÂBLES lors d'activité orageuse.

$ 12 Attention: Le cordon d’alimentation sert de mise hors circuit. Pour couper

l’alimentation du matériel, débrancher le cordon.

$ 13 EQUIPEMENT POUR BRANCHEMENT ELECTRIQUE, la prise de sortie doit être

placée près de l’équipement et facilement accessible".

$ 14 Attention: Ne pas bloquer les fentes d’aération, ceci empêcherait l’air

ambiant de circuler librement pour le refroidissement.

$ 15 L'alimentation du concentrateur doit être uniquement fournie par l'adaptateur.

EUROPE - EU

Utiliser un adaptateur secteur conforme TÜV de 3.3V, 1.5A en courant continu.

$ 16 TEMPÉRATURE DE FONCTIONNEMENT

Ce matériel est capable de tolérer une température ambiante maximum de 40 degrés
Celsius.

$ 17 POUR TOUS PAYS: Installer le matériel conformément aux normes électriques

nationales et locales.

Standardit: Tämä tuote on seuraavien standardien mukainen.

$ 1 Radioaaltojen häirintä EN55022 Luokka B

$ 2Varoitus: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä

tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin
toimenpiteisiin.

$ 3Kestävyys EN55024

$ 4Varoitus: Tämä tuote vaatii suojattuja kaapeleita toimiakseen emissio- ja

häiriönsietostandardien mukaisesti. Jos tuotetta käytetään ilman suojattuja
kaapeleita, käyttäjä voi joutua korjaamaan häirinnän aiheuttaman ongelman
omalla kustannuksellaan.

$ 5Sähköturvallisuus EN60950 (TUV), UL1950 (UL/cUL)

$ 6Laser EN60825

TURVALLISUUS

$ 7Varoitus Luokan 1 Lasertuote.

$ 8Variotus Älä katso säteeseen.
$ 9 SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA

VAROITUS: S ÄHKÖISKUVAARA Estääksesi SÄHKÖISKUN älä poista
kantta. Sisällä ei ole käyttäjän huollettavissa olevia osia. Tämä laite
sisältää VAARALLISIA JÄNNITTEITÄ ja sen voi avata vain koulutettu
ja pätevä teknikko. Välttääksesi SÄHKÖISKUN mahdollisuuden
katkaise sähkövirta tuotteeseen ennen kuin liität tai irrotat
paikallisverkon (LAN) kaapelit.

$ 10 Tämä on “ENSIMMÄISEN LUOKAN VALODIODITUOTE”

27

Electrical Safety and Ins tallation Requiremen t s

$ 11 SALAMANISKUVAARA

ENGENVAARA: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA

SALAMOINNIN AIKANA.

$ 12 HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN VIRRANKATKAISULAITTEENA.

VIRTA KATKAISTAAN irrottamalla virtajohto.

$ 13 PISTORASIAAN KYTKETTÄVÄ LAITE; pistorasia on asennettava laitteen lähelle

ja siihen on oltava esteetön pääsy."

$ 14 HUOMAUTUS: Ilmavaihtoreikiä ei pidä tukkia ja niillä täytyy olla vapaa yhteys

ympäröivään huoneilmaan, jotta ilmanvaihto tapahtuisi.

$ 15 Tähtipisteeseen (hub) syötettävän virran pitää tulla ainoastaan sovittimesta.

EUROPE - EU

Käytä TÜV-lisenssillä valmistettua verkkosovitinta, jonka tasajännitteen
nimellisarvot ovat DC 3.3V, 1.5A (milliampeeria).

$ 16 KÄYTTÖLÄMPÖTILA

Tämä tuote on suunniteltu ympäröivän ilman maksimilämpötilalle 40° C.

$ 17 KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten

sähköturvallisuusmääräysten mukaisesti.

Standard: Questo prodotto è conforme ai seguenti standard.

$ 1 Emissione RFI (interferenza di

radiofrequenza) EN55022 Classe

B

$ 2Avvertenza: in ambiente domestico questo prodotto potrebbe causare radio

interferenza. In questo caso potrebbe richiedersi all'utente di prendere gli adeguati
provvedimenti.

$ 3 Immunità EN55024

$ 4Avvertenza: questo prodotto, se utilizzato con cavi schermati, è conforme alle

norme sulle emissioni e sull’immunità. In caso di uso senza cavi schermati, l’utente
può dover adottare a proprie spese misure correttive contro le interferenze.

$ 5 Sicurezza elettrica EN60950 (TUV), UL1950 (UL/cUL)

$ 6Laser EN60825

NORME DI SICUREZZA

$ 7Avvertenza Prodotto laser di Classe 1.

$ 8Avertenza Non fissare il raggio con gli occhi.
$ 9 AVVERTENZE ELETTRICHE

ATTENZIONE: PERICOLO DI SCOSSE ELETTRICHE
Per evitare SCOSSE ELETTRICHE non asportare il coperchio. Le
componenti interne non sono riparabili dall’utente. Questa unità ha
TENSIONI PERICOLOSE e va aperta solamente da un tecnico
specializzato e qualificato. Per evitare ogni possibilità di SCOSSE
ELETTRICHE, interrompere l’alimentazione del dispositivo prima di
collegare o staccare i cavi LAN.

$ 10 Questo è un “PRODOTTO CON LED DI CLASSE 1”

$ 11 PERICOLO DI FULMINI

Pericolo: NON LAVORARE sul dispositivo o sui CAVI durante PRECIPITAZIONI
TEMPORALESCHE.

28

AT-FS21x and AT-FS212/x Series In st al l a tion G ui de

$ 12 Attenzione: Il cavo di alimentazione è usato come dispositivo di disattivazione. Per

togliere la corrente al dispositivo staccare il cavo di alimentazione.

$ 13 APPARECCHIATURA COLLEGABILE, la presa va installata vicino all’apparecchio

per risultare facilmente accessibile".

$ 14 ATTENZIONE: le prese d’aria non vanno ostruite e devono consentire il libero

ricircolo dell’aria ambiente per il raffreddamento.

$ 15 Questo dispositivo deve essere alimentato solo mediante l’adattatore.

EUROPE - EU

Utilizzare l’adattatore per c.a. da 3.3V c.c. e 1.5A conforme alla normativa TÜV.

$ 16 TEMPERATURA DI FUNZIONAMENTO

Questo prodotto è concepito per una temperatura ambientale massima di 40 gradi
centigradi.

$ 17 TUTTI I PAESI: installare il prodotto in conformità delle vigenti normative

elettriche nazionali.

Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer.

$ 1 RFI stråling EN55022 Klasse B

$ 2 Advarsel: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake

radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler.

$ 3 Immunitet EN55024

$ 4 Advarsel: Dette produktet må brukes med vernede kabler for å tilfredsstille

emisjons- og fritakelsesstandarder. Dersom produktet brukes med uvernede kabler,
må brukeren muligens rette forstyrrelsesproblemene for egen regning.

$ 5 Elektrisk sikkerhet EN60950 (TUV), UL1950 (UL/cUL)

$ 6Laser EN60825

SIKKERHET

$ 7ADVARSEL Laserprodukt av klasse 1.

$ 8ADVARSAL Stirr ikke på strålen.
$ 9 ELEKTRISITET

Advarsel: FARE FOR ELEKTRISK SJOKK
For å unngå ELEKTRISK sjokk, må dekslet ikke tas av. Det finnes ingen
deler som brukeren kan reparere på innsiden. Denne enheten inneholder
FARLIGE SPENNINGER, og må kun åpnes av en faglig kvalifisert
tekniker. For å unngå ELEKTRISK SJOKK må den elektriske strømmen
til produktet være avslått før LAN-kablene til- eller frakobles.

$ 10 Dette er et “KLASSE 1 LED PRODUKT”

$ 11 FARE FOR LYNNEDSLAG

FARE: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.

$ 12 Forsiktig: STRØMLEDNINGEN BRUKES TIL Å FRAKOBLE UTSTYRET. FOR

Å DEAKTIVISERE UTSTYRET, må strømforsyningen kobles fra.

$ 13 UTSTYR FOR STIKKONTAKT. Stikkontakten skal monteres i nærheten av

utstyret og skal være lett tilgjengelig."

$ 14 Forsiktig: Lufteventilene må ikke blokkeres, og må ha fri tilgang til luft med

romtemperatur for avkjøling.

$ 15 All strømtilførsel må komme fra adapteren.

29

Electrical Safety and Ins tallation Requiremen t s

EUROPE - EU

Benytt TÜV-godkjent AC-adapter på 3.3V DC, 1.5A (millismpere)

$ 16 DRIFTSTEMPERATUR

Dette produktet er konstruert for bruk i maksimum romtemperatur på 40 grader
celsius.

$ 17 ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale

elektriske koder.

Padrões: Este produto atende aos seguintes padrões.

$ 1Emissão De Interferência De

Radiofrequência EN55022 Classe

B

$ 2Aviso: Num ambiente doméstico este produto pode causar interferência na

radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas
adequadas.

$ 3 Imunidade EN55024

$ 4Advertência: Este produto requer a utilização de cabos blindados para

cumprimento dos standards de limites de emissão e imunidade. Se o produto for
utilizado com cabos não blindados, o utilizador poderá necessitar de tomar medidas
para correcção de problemas de interferência, por sua própria conta.

$ 5Segurança Eléctrica EN60950 (TUV), UL1950 (UL/cUL)

$ 6Laser EN60825

SEGURANÇA

$ 7Aviso Produto laser de classe 1.

$ 8Aviso Não olhe fixamente para o raio.
$ 9 AVISOS SOBRE CARACTERÍSTICAS ELÉTRICAS

Atenção: PERIGO DE CHOQUE ELÉTRICO
Para evitar CHOQUE ELÉTRICO, não retire a tampa. Não contém peças
que possam ser consertadas pelo usuário. Este aparelho contém
VOLTAGENS PERIGOSAS e só deve ser aberto por um técnico
qualificado e treinado. Para evitar a possibilidade de CHOQUE
ELÉTRICO, desconecte o aparelho da fonte de energia elétrica antes de
conectar e desconectar os cabos da LAN.

$ 10 Este é um “PRODUTO CLASSE 1 LED”

$ 11 PERIGO DE CHOQUE CAUSADO POR RAIO

PERIGO: NÃO TRABALHE no equipamento ou nos CABOS durante períodos
suscetíveis a QUEDAS DE RAIO.

$ 12 Cuidado: O cabo de alimentação é utilizado como um dispositivo de desconexão.

Para deseletrificar o equipamento, desconecte o cabo de alimentação.

$ 13 EQUIPAMENTO DE LIGAÇÃO, a tomada eléctrica deve estar instalada perto do

equipamento e ser de fácil acesso."

$ 14 Cuidado: As aberturas de ventilação não devem ser bloqueadas e devem ter acesso

livre ao ar ambiente para arrefecimento adequado do aparelho.

$ 15 Use somente o adaptador fornecido para alimentação elétrica do hub.

EUROPE - EU

Use um adaptador de corrente alternada com saída DC de 3.3V e 1.5A em
conformidade com as especificações da TÜV.

30

AT-FS21x and AT-FS212/x Series In st al l a tion G ui de

$ 16 TEMPERATURA DE FUNCIONAMENTO

Este produto foi projetado para uma temperatura ambiente máxima de 40 graus
centígrados.

$ 17 TODOS OS PAÍSES: Instale o produto de acordo com as normas nacionais e locais

para instalações elétricas.

Estándares: Este producto cumple con los siguientes estándares.

$ 1Emisión RFI EN55022 Clase B

$ 2Advertencia: en un entorno doméstico, este producto puede causar

radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas
que sean convenientes al respecto.

$ 3 Inmunidad EN55024

$ 4Advertencia: Este producto exige cables protectores para ajustarse a las normas de

emisión e inmunidad. Si se utiliza con cables sin protección, el usuario tendrá que
correr con los gastos por las medidas a tomar en caso de problemas de interferencias.

$ 5Seguridad eléctrica EN60950 (TUV), UL1950 (UL/cUL)

$ 6Laser EN60825

SEGURIDAD

$ 7 ¡ADVERTENCIA! Producto láser Clase 1.

$ 8 ¡ADVERTENCIA! No mirat fijamente el haz.
$ 9 AVISOS ELECTRICOS

Advertencia: PELIGRO DE ELECTROCHOQUE
Para evitar un ELECTROCHOQUE, no quite la tapa. No hay ningún
componente en el interior al cual puede prestar servicio el usuario. Esta
unidad contiene VOLTAJES PELIGROSOS y sólo deberá abrirla un
técnico entrenado y calificado. Para evitar la posibilidad de
ELECTROCHOQUE desconecte la corriente eléctrica que llega al
producto antes de conectar o desconectar los cables LAN.

$ 10 Este es un “PRODUCTO DE DIODO LUMINISCENTE (LED) CLASE 1”

$ 11 PELIGRO DE RAYOS

Eligro: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los equipos
o en LOS CABLES durante TORMENTAS ELECTRICAS.

$ 12 ATENCION: EL CABLE DE ALIMENTACION SE USA COMO UN

DISPOSITIVO DE DESCONEXION. PARA DESACTIVAR EL EQUIPO, desconecte
el cable de alimentación.

$ 13 EQUIPO CONECTABLE, el tomacorriente se debe instalar cerca del equipo, en un

lugar con acceso fácil".

$ 14 ATENCION: Las aberturas para ventilación no deberán bloquearse y deberán tener

acceso libre al aire ambiental de la sala para su enfriamiento.

$ 15 La energía para el dispositivo central o "hub" debe provenir únicamente del

adaptador.

EUROPE - EU

Utilizar un adaptador de corriente alterna autorizado TÜV de 3.3 voltios de corriente
continua y 1.5 miliamperios.

$ 16 TEMPERATURA REQUERIDA PARA LA OPERACIÓN

Este producto está diseñado para una temperatura ambiental máxima de 40 grados
C.

31

Electrical Safety and Ins tallation Requiremen t s

$ 17 PARA TODOS LOS PAÍSES: Monte el producto de acuerdo con los Códigos

Eléctricos locales y nacionales.

Standarder: Denna produkt uppfyller följande standarder.

$ 1Radiostörning EN55022 Klass B

$ 2 Varning: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan

tvinga användaren till att vidtaga erforderliga åtgärder.

$ 3 Immunitet EN55024

$ 4 Varning! Denna produkt kräver skärmade kablar för att uppfylla standardkraven

för emission och immunitet. Om den används med oskärmade kablar kan
användaren vara tvungen att vidta åtgärder på egen bekostnad för att åtgärda
störningsproblemet.

$ 5Elsäkerhet EN60950 (TUV), UL1950 (UL/cUL)

$ 6Laser EN60825

SÄKERHET

$ 7 Varning! Laserprodukt av klass 1.

$ 8 Varning! Laserstrålning när enheten är öppen.

$ 9 TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICITETSRISK:

RISK FÖR ELEKTRISK STÖTFör att undvika ELEKTRISK stöt, ta ej av locket. Det
finns inga delar inuti som behöver underhållas. Denna apparat är under
HÖGSPÄNNING och får endast öppnas av en utbildad kvalificerad tekniker. För att
undvika ELEKTRISK STÖT, koppla ifrån produktens strömanslutning innan LAN­kablarna ansluts eller kopplas ur.

$ 10 Detta är en “KLASS 1 LYSDIODPRODUKT”

$ 11 FARA FÖR BLIXTNEDSLAG

Fara: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER.

$ 12 Varning: Nätkabeln används som strömbrytare för att koppla från strömmen, dra

ur nätkabeln.

$ 13 UTRUSTNING MED PLUGG. Uttaget skall installeras i utrustningens närhet och

vara lättåtkomligt".

$ 14 VARNING: Luftventilerna får ej blockeras och måste ha fri tillgång till omgivande

rumsluft för avsvalning.

$ 15 Endast anslutningsenheten får vara kraftkälla till centralen.

EUROPE - EU

Använd en växelströmsanslutningsenhet licensierad av TÜV. Likström 3.3V, 1.5A.

$ 16 DRIFTSTEMPERATUR

Denna produkt är konstruerad för rumstemperatur ej överstigande 40 grader
Celsius.

$ 17 ALLA LÄNDER: Installera produkten i enlighet med lokala och statliga

bestämmelser för elektrisk utrustning.

32

Appendix C

Technical Support Fax Order

Name _________________________________________________________________
Company______________________________________________________________
Address _______________________________________________________________
City______________________ State/Province _______________________________
Zip/Postal Code ________________ Country _______________________________
Phone______________________________ Fax_______________________________

Incident Summary

Model number of Allied Telesyn product I am using _______________________
Network software products I am using ___________________________________

______________________________________________________________________

Brief summary of problem ______________________________________________

______________________________________________________________________

Conditions (List the steps that led up to the problem.) _____________________

______________________________________________________________________
______________________________________________________________________
______________________________________________________________________

Detailed description (Use separate sheet, if necessary)

______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________

When completed, fax this sheet to the appropriate Allied Telesyn office. Fax
numbers can be found on page viii.

33