Allied Telesis AT-FS203 User Manual [en, de, es, fr, it]

AT-FS201
AT-FS201ST/FS1, FS2, FS3
AT-FS202
AT-FS202SC/FS1, FS2, FS3
AT-FS203

Fast Ethernet Switches

Installation Guide

PN 613-10761-00 Rev B

Copyright  2000 Allied Telesyn International, Corp.
960 Stewart Drive, Suite B, Sunnyvale CA 94086 USA

All rights reserved. No part of this publication may be reproduced without prior written
permission fro Allied Telesyn International, Corp.

Ethernet is a registered trademark of Xerox Corporation. All other product names,
company names, logos or other designations mentioned herein are trademarks or
registered trademarks of their respective owners.

Allied Telesyn International, Corp. reserves the right to make changes in specifications
and other information contained in this document without prior written notice. The
information provided herein is subject to change without notice. In no event shall Allie
Telesyn International, Corp. be liable for any incidental, special, indirect, or
consequential damages whatsoever, including but not limited to lost profits, arising out
of or related to this manual or the information contained herein, even if Allied Telesyn
International, Corp. has been advised of, known, or should have known, the possibility
of such damages.

Safety Warnings

Standards

RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with this instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the
FCC, can void your right to operate this equipment.

This Class A digital apparatus meets all requirements of the Canadian Interference­Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.

RFI Emission
Warning

case the user may be required to take adequate measures.

Immunity
Warning

standards. If it is used with unshielded cables, the user may be required to take measures
to correct the interference problem at their own expense.

Electrical Safety
Laser
Warning
Warning

At time of installation, the Fiber Optic Lasers comply with FDA Radiation Performance
Standard 21CFR Subchapter J, applicable at date of manufacture.

This is a “CLASS 1 LED PRODUCT” (AT-FS201, AT-FS202, AT-FS203 models)

Important

equipment. When you see the , go to Appendix B for the translated safety statement in
your language.

Wichtig

Geräts. Wenn Sie  sehen, schlagen Sie in Anhang B den übersetzten Sicherheitshinweis
in Ihrer Sprache nach.

Vigtigt

dette udstyr. Når De ser symbolet , skal De slå op i tillæg B og finde de oversatte
sikkerhedsadvarsler i Deres eget sprog.

Belangrijk

deze apparatuur. Wanneer u de  ziet, raadpleeg Appendix B voor vertaalde
veiligheidsinstructies in uw taal.

: This product meets the following standards

U.S. Federal Communications Commission

Industry Canada





6



4

1

2

3



5



9

EN55022 Class A

: In a domestic environment this product may cause radio interference in which

EN50082-1 1997

: This product requires shielded cables to comply with emission and immunity



EN60950, UL1950, CSA 950
EN60825



7

Class 1 Laser product.
Do not stare into the Laser beam.

: Appendix B contains translated safety statements for installing this

: Anhang B enthält übersetzte Sicherheitshinweise für die Installation dieses

: Tillæg B indeholder oversatte sikkerhedsadvarsler, der vedrører installation af

: Appendix B bevat vertaalde veiligheidsopmerkingen voor het installeren van





8

iii

Safety Warnings

Important

équipement. Lorsque vous voyez le symbole , reportez-vous à l'annexe B pour consulter
la traduction de ces instructions dans votre langue.

Tärkeää

Kun näe-symbolin, katso käännettyä turvaohjetta liitteestä B.

Importante

questa apparecchiatura. Il simbolo , indica di consultare l’Appendice B per l’avviso di
sicurezza nella propria lingua.

Viktig

utstyret. Når du ser , åpner du til Tillegg B for å finne den oversatte
sikkerhetsinformasjonen på ønsket språk.

Importante

equipamento. Quando vir o símbolo , leia a advertência de segurança traduzida no seu
idioma no Anexo B.

Importante

instalación de este equipo. Cuando vea el símbolo , vaya al Apéndice B para ver el
mensaje de seguridad traducido a su idioma.

Obs

denna utrustning. När du ser , skall du gå till Bilaga B för att läsa det översatta
säkerhetsmeddelandet på ditt språk.

: L'annexe B contient les instructions de sécurité relatives à l'installation de cet

: Liite B sisältää tämän laitteen asentamiseen liittyvät käännetyt turvaohjeet.

: l’Appendice B contiene avvisi di sicurezza tradotti per l’installazione di

: Tillegg B inneholder oversatt sikkerhetsinformasjon for installering av dette

: O Anexo B contém advertências de segurança traduzidas para instalar este

: El Apéndice B contiene mensajes de seguridad traducidos para la

! Bilaga B innehåller översatta säkerhetsmeddelanden avseende installationen av

iv

Table of Contents

Safety Warnings
Table of Contents
Welcome to Allied Telesyn

Where to Find Web-based Guides ................................................................... vii

Document Conventions .................................................................................... vii

Contacting Allied Telesyn...............................................................................viii

Online Support ......................................................................................... viii

For Technical Support and Services........................................................ viii

Technical Support E-mail Addresses ...................................................... viii

Returning Products ........................................................................................... ix

FTP Server......................................................................................................... ix

For Sales or Corporate Information .................................................................. x

Tell Us What You Think .................................................................................... x

Chapter 1
Description

Key Features....................................................................................................... 6

Switch Performance .................................................................................... 7

Status LEDs ................................................................................................ 8

External AC/DC Power Adapter................................................................. 8

MDI/MDI-X Switch ..................................................................................... 9

Configuration Switches............................................................................... 9

Functional Description..................................................................................... 10

Frame Processing ...................................................................................... 10

Address Recognition and Filtering........................................................... 10

Network Topologies.......................................................................................... 11

............................................................................................iii

........................................................................................... v

......................................................................... vii

...................................................................................................... 1

Chapter 2
Installing the Switch

Verifying the Package Contents ...................................................................... 13

Planning the Installation................................................................................. 14

Selecting a Site ................................................................................................. 16

Installing the Switch........................................................................................ 17

Warranty Registration ..................................................................................... 20

Troubleshooting................................................................................................ 20

Is the Switch Receiving Power?................................................................ 20

Connectivity Testing ................................................................................. 21

................................................................................... 13

v

Table of Contents

Is the Link LED Lit? ................................................................................. 21

Technical Support and Service ........................................................................ 22

Appendix A
Technical Specifications

............................................................................ 23

Pinout Assignments.......................................................................................... 26

Appendix B
Electrical Safety and Installation Requirements

.................................27

Appendix C
Technical Support Fax Order

................................................................... 37

Incident Summary............................................................................................ 37

Appendix D
AT-FS201, AT-FS202 and AT-FS203 Series

Installation Guide Feedback

..................................................................... 39

vi

Welcome to Allied Telesyn

This guide contains instructions on how to install the AT-FS201, AT-FS202,
and AT-FS203 Series of Fast Ethernet Switches.

Where to Find Web-based Guides

The Allied Telesyn web site at
easy way to access the most recent documentation and technical information
for all of our products. For product guides, you can go directly to the following
web page:

www.alliedtelesyn.com/support/lib_allproducts.htm

www.alliedtelesyn.com

provides you with an

.

Document Conventions

This guide uses several conventions that you should become familiar with first
before you begin to install the product.

Note

A note provides additional information.

Caution

A caution indicates that performing or omitting a specific action may
result in equipment damage or loss of data.

Warning

A warning indicates that performing or omitting a specific action may
result in bodily injury.

vii

Welcome to Allied Telesyn

Contacting Allied Telesyn

There are several ways to contact Allied Telesyn technical support: online,
telephone, fax, and e-mail.

Online Support

You can request technical support online by filling out the Tech-Assistant
Form at

For Technical Support and Services

www.alliedtelesyn.com/support.htm

.

Americas

United States, Canada, Mexico,
Central America, South America
Tel: [phone], option 4
Fax: [phone]

Asia

Singapore, Taiwan, Thailand, Malaysia,
Indonesia, Korea, Philippines, China,
India, Hong Kong
Tel: [phone]
Fax: [phone]

Australia

Tel: [phone]
Fax: [phone]

France

France, Belgium, Luxembourg,
The Netherlands, Middle East, Africa
Tel: [phone]
Fax: [phone]

Technical Support E-mail Addresses

United States and Canada

[e-mail]

Germany

Germany, Switzerland, Austria, Eastern
Europe
Tel: [phone]
Fax: [phone]

Italy

Italy, Spain, Portugal, Greece, Turkey,
Israel
Tel: [phone]
Fax: [phone]

Japan

Tel: [phone]
Fax: [phone]

United Kingdom

United Kingdom, Denmark, Norway,
Sweden, Finland
Tel: [phone]
Fax: [phone]

Latin America, Mexico, Puerto Rico, Caribbean, and Virgin Islands

[e-mail]

United Kingdom, Sweden, Norway, Denmark, and Finland

[e-mail]

viii

AT-FS200 Series Installation Guide

Returning Products

Products for return or repair must first be assigned a Return Materials
Authorization (RMA) number. A product sent to Allied Telesyn without a
RMA number will be returned to the sender at the sender’s expense.

To obtain an RMA number, contact Allied Telesyn’s Technical Support at one
of the following locations:

North America

2205 Ringwood Ave
San Jose, CA 95131
Tel: [phone], option 4
Fax: [phone]

Latin America, the Caribbean,
Virgin Islands

Tel: international code + 425-481-3852
Fax: international code + 425-483-9458

European Customer Support Centre

10/11 Bridgemead Close
Westmead Industrial Estate
Swindon, Wiltshire SN5 7YT
England
Tel: [phone]
Fax: [phone]

Mexico and Puerto Rico

Tel: [phone], ext 3852 or

1-800-424-4284, ext 3852
Mexico only:95-800-424-5012, ext 3852
Fax: international code + 425-489-9191

FTP Server

If you need a device driver for an Allied Telesyn device, such as an AT-8224XL
Fast Ethernet Switch, you can download the driver from our FTP server at

ftp://gateway.centre.com

.

At login, enter ‘anonymous’. Enter your e-mail address for the password as
requested by the server at login.

ix

Welcome to Allied Telesyn

For Sales or Corporate Information

Allied Telesyn International, Corp.

19800 North Creek Parkway, Suite 200
Bothell, WA 98011
Tel: [phone]
Fax: [phone]

Allied Telesyn International, Corp.

960 Stewart Drive, Suite B
Sunnyvale, CA 94086
Tel: [phone] (USA and Canada)
Fax: [phone]

Tell Us What You Think

If you have any comments or suggestions on how we might improve this or
other Allied Telesyn documents, you can fill out the “AT-FS201, AT-FS202
and AT-FS203 Series Installation Guide Feedback” on page 39 and return the
form to us at the address or fax number provided. You can also provide
feedback online by filling out the Feedback on Documentation form at

www.alliedtelesyn.com/forms/feedbackman.htm

.

x

Chapter 1

Description

The AT-FS201, AT-FS202, and AT-FS203 Series of Fast Ethernet Switches
are designed to interconnect LAN devices and subnetworks over large
distances into an integrated network. These dual-port switches can also be
used to improve the performance of your network by dividing it into smaller,
more manageable segments.

The AT-FS201 and AT-FS202 Switches feature one 10/100Base-TX twisted
pair port with an operating distance of 100 meters (328 feet), and a
100Base-FX fiber optic port with an operating distance of 2 kilometers (1.2
miles) to 75 kilometers (46.5 miles), depending on the model.

The AT-FS203 Switch features two 10/100Base-TX ports, each with a
maximum distance of 100 meters (328 feet).

These Fast Ethernet switches can be installed either as standalone units,
such as on a table, or in an AT-MCR12 or AT-TRAY4 Chassis. They are easy
to install and do not require software configuration or management. The
following figures illustrate the front and rear panels of each switch.

AUTO N EG

TX

RX

COL

LNK

100

FD

TX RX

10Base-T/
100Base-TX

MDI MDI-X

FS201 FAST ETHERNET SWITCH

Figure 1

10Base-T/

100Base-TX

MDI MDI-X

PORT 2PORT 1

IEEE 802.3 / 802.3U

AT-FS201 Front Panel

AUTO N EG

TX

RX

COL

PWR

LNK

100

FD

1

Description

AUTO NEG

TX

RX

COL

LNK

100

FD

TX RX

10Base-T/
100Base-TX

MDI MDI-X

FS202 FAST ETHERNET SWITCH IEEE 802.3 / 802.3U

AT-FS202 Front Panel

10Base-T/
100Base-TX

MDI MDI-X

AUTO NEG

TX

RX

COL

LNK

100

FD

Figure 2

FS203 FAST ETHERNET SWITCH

Figure 3

AT-FS203 Front Panel

10Base-T/

100Base-TX

MDI MDI-X

PORT 2PORT 1

10Base-T/

100Base-TX

MDI MDI-X

PORT 2PORT 1

IEEE 802.3 / 802.3U

AUTO NEG

TX

RX

COL

AUTO N EG

TX

RX

COL

PWR

LNK

100

FD

PWR

LNK

100

FD

PORT

21 1212

321 4567

DUPLEX

12 V DC

Figure 4

SPEED
(Mbps)

10
100

Rear Panel of the AT-FS203 Switch

MODE

HALF
FULL

AUTO

NEG

OFF
ON

BYTES

1522
1518

2

AT-FS201ST/FS1

AT-FS200 Series Installation Guide

100Base-FX

LNK

TX

100

RX

FD

COL

FS201ST/FS1 FAST ETHERNET SWITCH

AT-FS201ST/FS2

100Base-FX

LNK

TX

100

RX

FD

COL

FS201ST/FS2 FAST ETHERNET SWITCH

AT-FS201ST/FS3

100Base-FX

LNK

TX

100

RX

FD

COL

TX RX

TX RX

TX RX

CLASS 1

LASER PRODUCT

DO NOT STARE

INTO BEAM

CLASS 1

LASER PRODUCT

DO NOT STARE

INTO BEAM

CLASS 1

LASER PRODUCT

DO NOT STARE

INTO BEAM

10Base-T/

100Base-TX

MDI MDI-X

IEEE 802.3 /802.3U

10Base-T/

100Base-TX

MDI MDI-X

IEEE 802.3 /802.3U

10Base-T/

100Base-TX

MDI MDI-X

AUTO NEG

TX

RX

COL

PORT 2PORT 1 SINGLE MODE

AUTO NEG

TX

RX

COL

PORT 2PORT 1 SINGLE MODE

AUTO NEG

TX

RX

COL

PORT 2PORT 1 SINGLE MODE

PWR

LNK

100

FD

PWR

LNK

100

FD

PWR

LNK

100

FD

FS201ST/FS3 FAST ETHERNET SWITCH

Figure 5

AT-FS201ST Series Front Panel

IEEE 802.3 /802.3U

3

Description

AT-FS202SC/FS1

100Base-FX

LNK

TX

100

RX

FD

COL

FS202SC/FS1 FAST ETHERNET SWITCH

AT-FS202SC/FS2

100Base-FX

LNK

TX

100

RX

FD

COL

FS202SC/FS2 FAST ETHERNET SWITCH

AT-FS202SC/FS3

100Base-FX

LNK

TX

100

RX

FD

COL

TX RX

TX RX

TX RX

CLASS 1

LASER PRODUCT

DO NOT STARE

INTO BEAM

100Base-TX

MDI MDI-X

IEEE 802.3 /802.3U

CLASS 1

LASER PRODUCT

DO NOT STARE

INTO BEAM

100Base-TX

MDI MDI-X

IEEE 802.3 /802.3U

CLASS 1

LASER PRODUCT

DO NOT STARE

INTO BEAM

100Base-TX

MDI MDI-X

10Base-T/

10Base-T/

10Base-T/

AUTO NEG

TX

RX

COL

PORT 2PORT 1 SINGLE MODE

AUTO NEG

TX

RX

COL

PORT 2PORT 1 SINGLE MODE

AUTO NEG

TX

RX

COL

PORT 2PORT 1 SINGLE MODE

PWR

LNK

100

FD

PWR

LNK

100

FD

PWR

LNK

100

FD

FS202SC/FS3 FAST ETHERNET SWITCH

Figure 6

AT-FS202SC Series Front Panels

IEEE 802.3 /802.3U

4

AT-FS200 Series Installation Guide

Figure 7 illustrates the rear panel of the AT-FS201SC and AT-FS202ST
Series Switches.

PORT

1222

21 345

DUPLEX

12 V DC

SPEED

(Mbps)

10
100

MODE

HALF
FULL

AUTO

NEG

OFF
ON

BYTES

1522
1518

Figure 7

Rear Panel of the AT-FS201SC and AT-FS202ST Switches

Table 1

Maximum Operating Distance

Type of Connector Maximum Distance

Model

Port 1 Port 2 Port 1 Port 2

AT-FS201 RJ-45 ST 100 m (328 ft) 2 km (1.2 mi)

AT-FS201ST/FS1 RJ-45 ST 100 m (328 ft) 15 km (9.3 mi)

AT-F201ST/FS2 RJ-45 ST 100 m (328 ft) 40 km (24.8 mi)

AT-FS201ST/FS3 RJ-45 ST 100 m (328 ft) 75 km (46.5 mi)

AT-FS202 RJ-45 SC 100 m (328 ft) 2 km (1.2 mi)

AT-FS202SC/FS1 RJ-45 SC 100 m (328 ft) 15 km (9.3 mi)

AT-FS202SC/FS2 RJ-45 SC 100 m (328 ft) 40 km (24.8 mi)

AT-FS202SC/FS3 RJ-45 SC 100 m (328 ft) 75 km (46.5 mi)

AT-FS203 RJ-45 RJ-45 100 m (328 ft) 100 m (328 ft)

5

Description

Key Features

The switches have the following key features:

❑

LEDs for unit and port status

❑

MDI/MDI-X switch

❑

External AC/DC power adapters (North America, Continental Europe,
or United Kingdom)

❑

DIP switches for configuring the ports

❑

Full- or half-duplex operation on both ports

❑

ST or SC fiber optic connectors

❑

Data packet forwarding and filtering at full wire speed (10 Mbps to
100 Mbps, 100 Mbps to 100 Mbps, and 10 Mbps to 10 Mbps)

❑

Store and forward switching mode

❑

Automatic address learning and aging

❑

IEEE 802.3u compliant auto-negotiation

❑

Standard, compact size for use on a tabletop or in an AT-MCR12 or
AT-TRAY4 Chassis

6

AT-FS200 Series Installation Guide

Switch Performance

The switches perform at:

❑

148,800 pps for 100 Mbps and 14,880 pps for 10 Mbps for full wire
speed forwarding and filtering

❑

200 Mbps maximum throughput in 100 Mbps, full-duplex mode

❑

20 Mbps maximum throughput in 10 Mbps, full-duplex mode

❑

Up to 8,192 unicast MAC addresses and unlimited multicast/
broadcast addresses

❑

280 kib bytes (per port) packet buffer

❑

Low latency 14.3 µs (64-byte packet, 100 Mbps full-duplex)

Note

For definitions of technical terms associated with Allied Telesyn
products, refer to the Glossary on Allied Telesyn’s web site at

www.alliedtelesyn.com/support/gloss_a.htm

.

7

Description

Status LEDs

Table 2 defines the switch LEDs.

Table 2

LEDs

LED State Color Description

PWR ON Green Power is applied.

LNK ON Green Link established on the port.

100 ON

OFF

FD ON

Green The port is operating at 100 Mbps.

The port is operating at 10 Mbps.

Amber Full-duplex mode is enabled (two-way independent

transmission).

OFF

Half-duplex mode is enabled, indicating transmission
only in one direction at a time.

AUTO NEG ON Green Auto-negotiation is enabled on the port.

TX ON Green Data is being transmitted on the port.

RX ON Green Data is being received on the port.

COL ON Amber The port is sensing a collision signal.

External AC/DC Power Adapter

The power adapter supplies 12V DC to the switch. Allied Telesyn supplies an
approved safety compliant AC power adapter for the 120 and 240V AC
versions with an unregulated output of 12V DC.

Figure 8

8

External AC/DC Power Adapter (North American version shown)

AT-FS200 Series Installation Guide

10Base T/
100Base-TX

10Base-T/

100Base-TX

MDI MDI-X MDI MDI-X

PORT 2PORT 1

MDI/MDI-X Switch

The MDI/MDI-X (Media Dependent Interface/Media Dependent Interface with
Crossover) switch, located on the front panel, is a straight-through or
crossover cable selection switch. It enables the RJ-45 port to be connected to a
repeater or DTE device without using a special crossover cable. The default
setting of the switch is MDI-X, which means you can connect the RJ-45 port to
a workstation or to any other DTE device that uses a straight-through cable.
For the MDI configuration, slide the switch to the MDI position and connect
the RJ-45 port to a repeater, hub, or switch using a straight-through cable.
See Figure 9.

AUTO NEG

LNK

TX

100

RX

FD

COL

FS203 FAST ETHERNET SWITCH

10Base-T/
100Base-TX

MDI MDI-X

10Base-T/

100Base-TX

MDI MDI-X

PORT 2PORT 1

IEEE 802.3/ 802.3U

Figure 9

AUTO NEG

PWR

LNK

TX

100

RX

FD

COL

MDI/MDI-X Switch

Configuration Switches

The configuration switches on the rear panel of the unit are used to configure
the operating characteristics of the port, such as it’s port speed and duplex
mode, and the maximum packet size allowed by the switch.

Configuring a 100Base-FX fiber optic port involves setting its duplex mode to
either half- or full-duplex. Configuring a 10/100Base twisted pair port involves
setting the speed and duplex mode. You can have the switch do this
automatically through auto-negotiation or you can set these values manually.

The Byte switch controls the maximum packets size that the unit will allow.
You can set the switch to either 1518 bytes, which is the normal Ethernet
packet size or to 1522 bytes, which make the Ethernet unit compliant with the
IEEE 802.1Q VLAN tagging standard.

9

Description

Functional Description

The AT-FS200 series of switches function as unmanaged dual-port switches.

Frame Processing

The switches support store and forward switching at Fast Ethernet full-wire
speed either in 10 or 100 Mbps, half- or full-duplex mode. Packets entering
each port are stored in buffers. After the full packet is received, it is forwarded
or discarded depending on its destination address and error status. This
ensures that only error-free data packets destined for another segment will be
transferred across the switch, reducing network load. For example, if the
packet entering from Port 1 is destined for an end station on Port 2, it will be
forwarded if the Frame Check Sequence (FCS) is valid. If the packet from Port
1 is destined for an end station also attached to Port 1, then the packet is
discarded.

The switch will discard CRC error, misaligned, runt, and under-sized/over­sized packets. When the packet has dribble bits at the end, the switch will
truncate to octet boundary and check for a good FCS before forwarding.

Address Recognition and Filtering

Up to 8,192 MAC addresses can be stored in the MAC address table. The
switch will learn all new addresses in real-time after power-up with its
address self-learning mechanism. If the source address of an incoming packet
is not found in the address table, the switch waits until the end of the packet
to check for good CRC and then updates its MAC address table. Because the
switch has Automatic Address Aging, if a source address entry in the table is
not updated within five minutes, the entry is deleted from the table. The
switch forwards multicast, broadcast, and unicast packets when the MAC
address table size is exceeded.

10

AT-FS200 Series Installation Guide

Network Topologies

Figure 10 shows a network configuration where an AT-FS203 Switch is used
to interconnect two small networks of stackable hubs.

AT-3624TR

AT-FH812u

AT-FH812u

AT-FH812u

Figure 10

AT-3624TR

AT-3624TR

AT-FS203

Typical Configuration Using the AT-FS203 Switch

11

Chapter 2

Installing the Switch

This chapter explains how to install the switch. The switch can be installed
either as a standalone unit, such as on a table, or in an AT-MCR12 or
AT-TRAY4 Chassis.

Verifying the Package Contents

Make sure the following items are included in your switch package. If any of
the following items are missing or damaged, contact your sales representative.

❑

AT-FS201, AT-FS202, or AT-FS203 Fast Ethernet Switch

❑

Four protective feet (for standalone use only)

❑

External AC/DC power adapter (North America, Continental Europe,
or United Kingdom)

❑

This installation guide

❑

Warranty card

13

Installing the Switch

Planning the Installation

Be sure to observe the following guidelines when planning the installation of
your Ethernet switch.

❑

The end node connected to the fiber optic port on an AT-FS201ST or
AT-FS202SC switch must be able to operate at 100 Mbps.

❑

The end node connected to the twisted pair port(s) can operate at
either 10 Mbps or 100 Mbps.

❑

The end node connected to a port on the switch can be a network
adapter card, repeater, router, hub, or another switch.

❑

The twisted pair cabling must be kept away from sources of electrical
noise, such as radios, transmitters, power lines, broadband amplifiers,
electrical motor, and fluorescent fixtures.

❑

Refer to Table 3 for the cabling specifications for the twisted pair
port(s).

Table 3

Operating Mode Cable Type

10Base-T Shielded or unshielded Category 3 or better 100 m (328 ft)

100Base-TX Shielded or unshielded Category 5 or better 100 m (328 ft)

10/100Base-TX Twisted Pair Cabling Specifications

Maximum

Distance

14

AT-FS200 Series Installation Guide

❑

Refer to Table 4 for the cabling specifications for the fiber optic port
operating in full-duplex mode.

Table 4

Model

100Base-FX Fiber Optic Cabling Specifications (Full-duplex) for Port 2

Type of Fiber
Optic Cable

AT-FS201 50/125 or

62.5/125 micron
multimode

AT-FS201ST/FS1 50/125 or

62.5/125 micron
multimode

9/125 micron
single-mode

AT-F201ST/FS2 9/125 micron

single-mode

AT-FS201ST/FS3 9/125 micron

single-mode

AT-FS202 50/125 or

62.5/125 micron
multimode

AT-FS202SC/FS1 50/125 or 62.5/

125 multimode

Maximum
Distance

Maximum Allowable
Loss Budget

2 km (1.2 mi) 13 dB at 1310 nm

2 km (1.2 mi) 13 dB at 1310 nm

15 km (9.3 mi) 16 dB at 1310 nm

40 km (24.8 mi) 30 dB at 1310 nm

75 km (46.5 mi) 33 dB at 1310 nm

2 km (1.2 mi) 13 dB at 1310 nm

2 km (1.2 mi) 13 dB at 1310 nm

9/125 micron

15 km (9.3 mi) 16 dB at 1310 nm

single-mode

AT-FS202SC/FS2 9/125 micron

40 km (24.8 mi) 30 dB at 1310 nm

single-mode

AT-FS202SC/FS3 9/125 micron

75 km (46.5 mi) 33 dB at 1310 nm

single-mode

Note

Refer to Appendix A for further information on the technical
specifications of the fiber optic port on the switch.

15

Installing the Switch

❑

Refer to Table 5 for the cabling specifications for the fiber optic port
operating in half-duplex mode.

Table 5

100Base-FX Fiber Optic Ports (Half-duplex) For Port 2

1

Number of Media
Converters

Connected Devices Maximum Distance

One Media Converter Inline Switch to switch 372 m (1,221 ft)

Workstation to switch 372 m (1,221 ft)

Switch to Class I repeater 137 m (450 ft)

Switch to Class II repeater 185 m (607 ft)

Two Media Converters

Switch to switch 332 m (1,089 ft)

Inline

Workstation to switch 322 m (1, 089 ft)

Switch to Class I repeater 97 m (318 ft)

Switch to Class II repeater 145 m (476 ft)

1. The total distance of the fiber optic lengths cannot exceed the limits stated in the table. Each media converter used
inline within a single collision domain reduces the overall segment length by 40 m (131 ft).

Selecting a Site

Be sure to observe the following requirements when choosing a site for your
switch.

❑

Select a site that is dust-free and moisture-free.

❑

Be sure that the site will allow you to easily access the fiber optic and
twisted pair cables and the power cord.

❑

Use dedicated power circuits or power conditioners to supply reliable
power to the device.

16

AT-FS200 Series Installation Guide

Installing the Switch

To install the switch, perform the following procedures:

1. Remove all equipment from the package and store the packaging in a safe

place.

2. If you are installing the switch as a standalone unit, attach the four rubber

feet to the base of the unit, placing one rubber foot in each corner. (For
rack-mount chassis installation, do not attach the feet.)

3. Configure the DIP switches on the rear panel of the unit. Refer to Figure

11 and Figure 12 for the location of the switches and Table 6 and Table 7
for the possible settings.

Table 6

DIP Switch Settings for the AT-FS201 and AT-FS202 Switches

Port 2 1 2 2

Speed (Mbps) Duplex Mode Auto-neg Bytes

Up 10 Half Off 1522

Down 100 Full On 1518

Table 7

DIP Switch Settings for the AT-FS203 Switch

Port 1 2 1 2 1 2

Speed (Mbps) Duplex Mode Auto-neg (only) Bytes

Up 10 Half Off 1522

Down 100 Full On 1518

17

Installing the Switch

When setting the DIP switches, consider the following:

❑

The default setting of 1518 bytes for the maximum packet size is the
upper limit of the allowable Ethernet packet size as specified in the
IEEE 802.3 standard. At this setting, any packets over this size will
be considered illegal and will be dropped as part of the switch’s error­handling operations.

❑

Changing the setting of the maximum packet size to 1522 causes the
switch to function as a passive component of the network in
accordance with the IEEE 802.1Q VLAN tagging standard. The switch
will pass packets that adhere to the standard. This 1522 setting
should be used only in a network that uses the IEEE 802.1 Q VLAN
tagging standard.

❑

For a twisted pair port(s), setting the AUTO NEG switch to either ON
or OFF either enables or disables auto-negotiation on the port. If you
disable auto-negotiation, be sure to set the DIP switches for the port’s
speed and duplex mode to match the speed and duplex mode of the
end-node.

❑

For a fiber optic port, set the port’s duplex mode using the appropriate
DUPLEX MODE DIP switch. This setting must match the duplex
mode capability of the end-node to be connected to the port.

PORT

21 1212

321 4567

DUPLEX

AUTO

SPEED

BYTES

MODE

NEG

12V DC

(Mbps)

10

HALF

OFF

1522

100

FULL

ON

1518

PORT

21 1212

321 4567

Figure 11

DUPLEX

SPEED
(Mbps)

10
100

MODE

AT-FS203 DIP Switches

HALF
FULL

AUTO

NEG

OFF
ON

BYTES

1522
1518

18

12V DC

AT-FS200 Series Installation Guide

PORT

1222

21 345

DUPLEX

AUTO

SPEED

MODE

NEG

(Mbps)

BYTES

10

HALF

OFF

1522

100

FULL

ON

1518

PORT

1222

21 345

DUPLEX

MODE

HALF
FULL

AUTO

NEG

OFF
ON

BYTES

1522
1518

SPEED

(Mbps)

10
100

Figure 12

AT-FS201SC and AT-FS202ST DIP Switches

4. If you are installing the switch as a standalone unit, plug the AC/DC

power adapter into an appropriate AC power outlet and insert the power
plug into the DC receptacle, located on the rear panel. If you are installing
the switch in an AT-MCR12 or AT-TRAY4 Chassis, refer to the
appropriate guide for installation instructions.

5. Verify that the PWR LED on the switch lights green.

6. For an AT-FS201 or AT-FS202 switch, remove the dust cover from the fiber

optic port.

7. For an AT-FS201 or AT-FS202 switch, plug the fiber optic cable into Port

1. Verify that the near-end node transmitter port (TX) is connected to the
far end node receiver port (RX) and vice versa.

8. Plug the twisted pair cable(s) into the RJ-45 connector(s) (Port 2 for an

AT-FS201 or AT-FS202 switch and Ports 1 and 2 for the AT-FS203
switch).

9. Set the MDI/MDI-X switch as follows:

❑

If you are connecting the twisted pair port to a workstation, set the
MDI/MDI-X switch to the MDI-X position.

❑

If you are connecting the twisted pair port to a hub or to another
switch, set the MDI/MDI-X switch to the MDI position. See Figure 13.

19

Installing the Switch

10Base T/
100Base-TX

10Base-T/

100Base-TX

MDI MDI-X MDI MDI-X

PORT 2PORT 1

AUTO NEG

LNK

TX

100

RX

FD

COL

FS203 FAST ETHERNET SWITCH

10Base-T/
100Base-TX

MDI MDI-X

10Base-T/

100Base-TX

MDI MDI-X

PORT 2PORT 1

IEEE 802.3/ 802.3U

Figure 13

AUTO NEG

PWR

LNK

TX

100

RX

FD

COL

MDI/MDI-X Switch

Warranty Registration

When you finish the installation, register your product by completing the
enclosed warranty card and sending it in, or by visiting our web site at

www.alliedtelesyn.com/forms/warranty.htm

and completing the on-line

registration.

Troubleshooting

This section contains guidelines for troubleshooting the unit should a problem
occur.

Note

Whenever the speed and/or duplex mode are changed during or after
power ON, power OFF then power back on the switch to load the new
configuration.

Is the Switch Receiving Power?

❑

Verify that the Power LED is lit.

❑

If the Power LED is not ON, check the AC power adapter to verify that
the adapter is plugged into a functioning wall outlet and that the DC
power cord is properly inserted into the switch’s power connector.

20

AT-FS200 Series Installation Guide

Connectivity Testing

1. Connect each port to a node or workstation. Then connect the power cord.

2. Verify that the Link LEDs for Port 1 and Port 2 are lit.

If the Link LED does not light (TX):

❑

Verify that the switch’s port matches the speed selection of the device
attached to the other end.

❑

The switch settings are represented by each port’s LEDs. For
troubleshooting purposes, determine the current port settings, for
example auto-negotiation, 10 or 100 Mbps (speed) duplex mode.

❑

Change the MDI/MDI-X switch setting on the port and see if a link
occurs. If not, put the switch back to its original configuration.

If the Link LED does not light (FX):

❑

Make sure the remote end of the fiber optic cable is connected to a
100Base-FX device.

❑

Swap the near end fiber cable receive/transmit connectors.

Is the Link LED Lit?

The Link LEDs light when a proper connection between the corresponding 10/
100Base-TX or 100Base-FX port and the equipment connected to it is
established. If this LED is not lit, check for the problems listed as follows and
make corrections as necessary.

1. Problem 1:

The cable has been cut, damaged, or is the wrong type of cable.

❑

Solution 1:
— Try making the connection with a different cable. Be sure you are

using an undamaged cable of the correct type.

2. Problem 2:

Connected equipment is not turned ON or is not operating properly.

❑

Solution 2:
— Check the connected equipment (computer, another switch, etc.)

and turn ON the power.

— Make sure that the SPEED and Duplex Mode for each port of the

switch match the settings of the attached computer or additional
switch.

21

Installing the Switch

3. Problem 3:

The MDI/MDI-X slide switch for TX is on the wrong setting.

❑

Solution 3:
— Verify that you are using a known good cable, reposition the MDI/

MDI-X switch, and check that the Link LED is lit.

4. Problem 4:

There is signal loss between the switch and one of the attached network
nodes.

❑

Solution 4:
— Make sure the distance between the switch and the connected

network device does not exceed 100 meters (328 feet). (UTP is half­or full-duplex.)

— 412 meters (1,351 feet) for multi-mode fiber cable (half-duplex FX

operation/2 kilometers (1.2 miles) for full-duplex FX operation) See
Table 8, “Technical Specifications,” on page 23 for correct distances
for 10Base-T, 100Base-TX and 100Base-FX cable lengths.

Make sure you are using Category 5 cable when operating at 100 Mbps.

Technical Support and Service

You can contact the dealer where you purchased your product for local
assistance. If local help is unable to resolve your problem, Allied Telesyn offers
technical support via online, fax or telephone.

Refer to “Contacting Allied Teleysn” on page viii for technical support
information or
locations.

22

www.alliedtelesyn.com

for current world-wide office

Appendix A

Technical Specifications

Table 8 lists the technical specifications for the Fast Ethernet Switches.

Table 8

Physical Specifications

Dimensions (L x W x H) 10.5 cm x 9.5 cm x 2.5 cm

Weight 300 gm (10.5 oz)

Operating Temperatures 0° to 40° C

Storage Temperatures -20° to 80° C

Relative Humidity 5% to 80% (non-condensing)

Operating Altitude Up to 10,000 ft

Electrical and Mechanical Specifications

Standard CE Compliant IEEE 802.3, IEEE 802.3u

Immunity Conforms to EN500082-1 1997 immunity standard

Safety Conforms to all standards normally supported by Allied

EMI/RFI Meets all applicable requirements for emissions including

Electrical Rating

Technical Specifications

(4.12 in x 3.75 in 1.0 in)

Telesyn products including safety standards UL 1950, CSA

22.2 No. 950, TUV EN60950, EN60825 CE Compliant

but not limited to FCC Class A, IC Class A, EN55022 Class A

Input Supply Voltage 12V DC

Maximum Current
Rating

Maximum Power
Consumption

0.5A

6W

23

Technical Specifications

Table 8

Technical Specifications

Transmitter

Output Power 62.5/125 mM

-16.8 dBm
100/140 mM
50/125 mM

-20.3 dBm
85/125 mM

Fiber Optic Transmitter

Fiber
Optic
Diameter
(microns)

Model

AT-FS201 &
AT-FS202

AT-FS201ST/FS1 &
AT-FS202SC/FS1

Table 9

Fiber
Type

MMF 50/125 1310 nm -14.0 -20.3 -22.5

MMF 62.5/125 1310 nm -14.0 -16.8 -19.0

SMF 9/125 1310 nm -8.0 -11.5 -15.0

(Continued)

Optical
Frequency
(nm)

1

Launch Power (dBm)

Max. Avg Min.

AT-FS201ST/FS2 &
AT-FS202SC/FS2

AT-FS201ST/FS3 &
AT-FS202SC/FS3

1. The launch power is measured at one meter from the transmitter.

24

SMF 9/125 1310 nm 0.0 -3.0 -5.0

SMF 9/125 1310 nm 0.0 -2.0 -4.0

AT-FS200 Series Installation Guide

Table 10

Model

AT-FS201 &
AT-FS202

AT-FS201ST/FS1 &
AT-FS202SC/FS1

AT-FS201ST/FS2 &
AT-FS202SC/FS2

AT-FS201ST/FS3 &
AT-FS202SC/FS3

Fiber
Type

MMF 50/125 1310 nm -31.8 -34.5 -14.0

MMF 62.5/125 1310 nm -31.8 -34.5 -14.0

SMF 9/125 1310 nm -31.0 -31.0 -8.0

SMF 9/125 1310 nm -35.0 -38.0 0.0

SMF 9/125 1310 nm -37.0 -37.0 -3.0

Table 11

Model Fiber Type

Fiber Optic Receiver

Fiber
Optic
Diameter
(microns)

Fiber Optic Datalink

Min.
Power /
Link
Budget
(dB)

Optical
Frequency
(nm)

Avg.
Signal
Loss
(dB)

Receive Power (dBm)

Min.
Sensi­tivity

Typical
Sensi­tivity

Min.
Distance

1

Specs.

Satura­tion

Max.
Distance
Specs.

AT-FS201 &
AT-FS202

AT-FS201ST/FS1 &
AT-FS202SC/FS1

AT-FS201ST/FS2 &
AT-FS202SC/FS2

AT-FS201ST/FS3 &
AT-FS202SC/FS3

1. The recommended minimum range is stated in all cases where the maximum trans
mitter output power exceeds the receivers saturation level. This is to prevent blind­ing or burning out of the optical receiver on the far-end node.

50/125 MMF 13.00 18.70 0 2 km

62.5/125
MMF

9/125 SMF 16.00 19.50 0 15 km

9/125 SMF 30.00 35.00 0 40 km

9/125 SMF 33.00 35.00 15 km

16.80 22.50 0 2 km

(9.4 mi)

(1.25 mi)

(1.25 mi)

(9.4 mi)

(25 mi)

75 km
(46 mi)

25

Technical Specifications

Pinout Assignments

Figure 14 shows the pin assignments of the switch’s 10/100Base-TX RJ-45
connector.

Pin 1 Pin 8

Figure 14

RJ-45 Pin Assignments

Table 5 lists the 10/100Base-TX connector pins and their signals when the
MDI-X/MDI switch is in either position.

Table 12

Pinout Assignments

MDI-X (Default) Signal MDI Signal

1RX+1 TX+

2RX-2 TX-

3TX+3 RX+

4- 4 -

5- 5 -

6TX-6 RX-

7- 7 -

8- 8 -

26

Appendix B

Electrical Safety and Installation Requirements

Important

safety statements in this guide.

Wichtig

enthaltenen Sicherheitshinweise in mehreren Sprachen.

Vigtigt

sikkerhedsadvarslerne i denne håndbog.

Belangrijk

veiligheidsopmerkingen in deze gids.

Important

instructions de sécurité figurant dans ce guide.

Tärkeää

kielellä.

Importante

di sicurezza di questa guida.

Viktig

sikkerhetsinformasjonen i denne veiledningen.

Importante

advertências de segurança neste guia.

Importante

mensajes de seguridad incluidos en esta guía.

: This appendix contains multiple-language translations for the

: Dieser Anhang enthält Übersetzungen der in diesem Handbuch

: Dette tillæg indeholder oversættelser i flere sprog af

: Deze appendix bevat vertalingen in meerdere talen van de

: Cette annexe contient la traduction en plusieurs langues des

: Tämä liite sisältää tässä oppaassa esiintyvät turvaohjeet usealla

: questa appendice contiene traduzioni in più lingue degli avvisi

: Dette tillegget inneholder oversettelser til flere språk av

: Este anexo contém traduções em vários idiomas das

: Este apéndice contiene traducciones en múltiples idiomas de los

Obs!

Denna bilaga innehåller flerspråkiga översättningar av

säkerhetsmeddelandena i denna handledning.

27

Electrical Safety and Installation Requirements

Standards

RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with this instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or
the FCC, can void your right to operate this equipment.

This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement
sur le matériel brouilleur du Canada.



1 RFI Emission



2 Warning



3 Immunity



4 Warning



5 Electrical Safety



6Laser



7 Warning



8 Warning



9



10 LIGHTNING DANGER



11



12



13 OPERATING TEMPERATURE



14

which case the user may be required to take adequate measures.

immunity standards. If it is used with unshielded cables, the user may be required
to take measures to correct the interference problem at their own expense.

At time of installation, the Fiber Optic Lasers comply with FDA Radiation
Performance Standard 21CFR Subchapter J, applicable at date of manufacture.

This is a “CLASS 1 LED PRODUCT” (AT-FS201, AT-FS202, AT-FS203 models)

SAFETY

DANGER

LIGHTNING ACTIVITY.
DO NOT BLOCK AIR VENTS
Power to the hub must be sourced only from the adapter.

USA/CANADA

Use a UL Listed/CSA Certified AC adapter of DC 12V, 500mA.

EUROPE - EU

Use TÜV licensed AC adapter of DC 12V, 500mA.

UK

Use a UK Safety Approved AC adapter of DC 12V, minimum 500mA.

This product is designed for a maximum ambient temperature of 40 degrees C.

ALL COUNTRIES

Codes.

: This product meets the following standards.

U.S. Federal Communications Commission

: In a domestic environment this product may cause radio interference in

: This product requires shielded cables to comply with emission and

Class 1 Laser product.
Do not stare into the Laser beam.

: DO NOT WORK on equipment or CABLES during periods of

: Install product in accordance with local and National Electrical

Industry Canada

EN55022 Class A

EN50082-1 1997

EN60950, UL1950, CSA 950
EN60825

28

Normen

: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.



1 Hochfrequenzstörung



2Warnung



3 Störsicherheit



4Achtung



5 Elektrische Sicherheit



6Laser



7Warnung



8Warnung



9



10 GEFAHR DURCH BLITZSCHLAG



11



12



13 BETRIEBSTEMPERATUR



14 ALLE LÄNDER

hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen
ergreifen.

Richtlinien für Emission und Interferenzschutz entsprochen wird. Falls das Produkt
mit nicht abgeschirmten Kabeln verwendet wird, können weitergehende
Maßnahmen für die Korrektur von Interferenzproblemen auf Kosten des Benutzers
notwendig werden.

Das ist ein “LED Produkt der Klasse 1”

SICHERHEIT

GEFAHR

ausführen
ENTLÜFTUNGSÖFFNUNGEN NICHT VERSPERREN
Der Buchse darf nur aus dem Adapter Strom zugeführt werden.

EUROPE - EU

Gebrauchen Sie einen von TÜV zugelassenen Wechselstromadapter für Gleichstrom
12 V, 500 mA.

Dieses Produkt wurde für den Betrieb in einer Umgebungstemperatur von nicht
mehr als 40° C entworfen.

Vorschriften entsprechen.

: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen

: Für dieses Produkt sind abgeschirmte Kabel erforderlich, damit den

Laserprodukt der Klasse 1.
Nicht direkt in den Strahl blicken.

: Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters

: Installation muß örtlichen und nationalen elektrischen

AT-FS200 Series Installation Guide

EN55022 Klasse A

EN50082-1 1997

EN60950, UL1950, CSA 950
EN60825

Standarder



1 Radiofrekvens



2 Advarsel



3 Immunitet



4 Advarsel



5 Elektrisk sikkerhed



6Laser



7 Advarsel



8 Advarsel



9

forstyrrelsesemission

Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige
foranstaltninger.

bestemmelserne vedrørende udstråling og støjimmunitet. Hvis det bruges med
uafskærmede kabler, kan det blive påkrævet af brugeren at korrigere
interferensproblemer for egen regning.

Dette er et “PRODUKT UNDER KLASSE 1 LED”

: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse.

: Dette produkt skal bruges med afskærmede kabler for at overholde

Laserprodukt av klasse 1.

Stirr ikke på strålen.

: Dette produkt tilfredsstiller de følgende standarder.

EN55022 Klasse A

EN50082-1 1997

. EN60950, UL1950, CSA 950

EN60825

29

Electrical Safety and Installation Requirements

SIKKERHED



10 FARE UNDER UVEJR



11



12



13 BETJENINGSTEMPERATUR



14 ALLE LANDE



1 RFI Emissie



2 Waarschuwing



3 Immuniteit



4 Waarschuwing



5 Electrische Veiligheid



6Laser



7 Waarshuwing



8 Waarchuwing



9



10 GEVAAR VOOR BLIKSEMINSLAG



11



12



13 BEDRIJFSTEMPERATUUR



14 ALLE LANDEN

FARE

: UNDLAD at arbejde på udstyr eller KABLER i perioder med

LYNAKTIVITET.
VENTILATIONSÅBNINGERNE MÅ IKKE BLOKERES
Strømforsyningen til apparatet må udelukkende tages fra

tilpasningstransformatoren.

EUROPE - EU

Brug kun TÜV godkendt vekselstrømstransformator på 12 V jævnstrøm, 500 mA.

Dette apparat er konstrueret til en omgivende temperatur på maksimum 40 grader
C.

national lovgivning for elektriske installationer.

Eisen

geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen.

apparaat te zijn voorzien van afgeschermde kabels. Als het met niet-afgeschermde
kabels wordt gebruikt, kan het zijn dat de gebruiker maatregelen moet treffen om
interferentieproblemen voor eigen rekening op te lossen.

Dit is een “KLASSE 1 LED-PRODUKT”

VEILIGHEID

GEVAAR

VENTILATIEGATEN NIET BLOKKEREN
Stroom mag alleen via de adapter naar het apparaat toegevoerd worden.

EUROPE - EU

Gebruik een door TÜV gekeurde wisselstroomadapter van 12 Volt gelijkstroom, 500
milliampères.

De omgevingstemperatuur voor dit produkt mag niet meer bedragen dan 40 graden
Celsius.

elektrische voorschriften.

: Installation af produktet skal ske i overensstemmelse med lokal og

: Dit product voldoet aan de volgende eisen.

: Binnenshuis kan dit product radiostoring veroorzaken, in welk

: Om te voldoen aan de emissie- en immuniteitsnormen dient dit

Klasse-1 laser produkt.

Neit in de straal staren.

: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.

: het toestel installeren overeenkomstig de lokale en nationale

EN55022 Klasse A

EN50082-1 1997

EN60950, UL1950, CSA 950
EN60825

30

Normes

: ce produit est conforme aux normes de suivantes.



1 Emission d'interférences



2Mise En Garde



3 Immunité



4 Avertissement



5 Sécurité électrique



6Laser



7 Attention



8 Attention



9



10 DANGER DE FOUDRE



11



12



13 TEMPÉRATURE DE FONCTIONNEMENT



14 POUR TOUS PAYS

radioélectriques

interférences radioélectriques. Auquel cas, l'utilisateur devra prendre les mesures
adéquates.

les normes d’émission et d’immunité. Si l’utilisateur choisit d’utiliser des câbles non
blindés, il sera peut-être contraint de prendre les mesures nécessaires pour corriger
les problèmes d’interférences, ainsi que d’assumer le coût correspondant.

Ce mat‚riel est un “PRODUIT A DIODE LECTROLUMINESCENTE DE CLASSE 1”

SÉCURITÉ

DANGER

NE PAS BLOQUER LES FENTES D'AÉRATION
L'alimentation du concentrateur doit être uniquement fournie par l'adaptateur.

EUROPE - EU

Utiliser un adaptateur secteur conforme TÜV de 12 V, 500 mA en courant continu.

Ce matériel est capable de tolérer une température ambiante maximum de 40 degrés
Celsius.

nationales et locales.

: dans un environnement domestique, ce produit peut provoquer des

: Il faut utiliser des câbles blindés pour ce produit afin de respecter

Producit laser di classe 1.
Ne pas fixer le faisceau des yeux.

: NE PAS MANIER le matériel ou les CÂBLES lors d'activité orageuse.

: Installer le matériel conformément aux normes électriques

AT-FS200 Series Installation Guide

EN55022 Classe

EN50082-1 1997

EN60950, UL1950, CSA 950
EN60825

A

Standardit



1 Radioaaltojen häirintä



2Varoitus



3 Kestävyys



4Varoitus



5 Sähköturvallisuus



6Laser



7Varoitus



8Variotus



9



10 SALAMANISKUVAARA



11

tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin
toimenpiteisiin.

häiriönsietostandardien mukaisesti. Jos tuotetta käytetään ilman suojattuja
kaapeleita, käyttäjä voi joutua korjaamaan häirinnän aiheuttaman ongelman
omalla kustannuksellaan.

Tämä on “ENSIMMÄISEN LUOKAN VALODIODITUOTE”

TURVALLISUUS

ENGENVAARA

SALAMOINNIN AIKANA.
ÄLÄ TUKI ILMAREIKIÄ

: Tämä tuote on seuraavien standardien mukainen.

: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä

: Tämä tuote vaatii suojattuja kaapeleita toimiakseen emissio- ja

Luokan 1 Lasertuote.
Älä katso säteeseen.

EN55022 Luokka A

EN50082-1 1997

EN60950, UL1950, CSA 950
EN60825

: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA

31

Electrical Safety and Installation Requirements



12



13 KÄYTTÖLÄMPÖTILA



14 KAIKKI MAAT

Tähtipisteeseen (hub) syötettävän virran pitää tulla ainoastaan sovittimesta.

EUROPE - EU

Käytä TÜV-lisenssillä valmistettua verkkosovitinta, jonka tasajännitteen
nimellisarvot ovat DC 12 V, 500 mA (milliampeeria).

Tämä tuote on suunniteltu ympäröivän ilman maksimilämpötilalle 40° C.

sähköturvallisuusmääräysten mukaisesti.

: Asenna tuote paikallisten ja kansallisten

Standard



1 Emissione RFI (interferenza di



2 Avvertenza



3 Immunità



4 Avvertenza



5 Sicurezza elettrica



6Laser



7 Avvertenza



8 Avertenza



9



10 PERICOLO DI FULMINI



11



12



13 TEMPERATURA DI FUNZIONAMENTO



14 TUTTI I PAESI

radiofrequenza)

interferenza. In questo caso potrebbe richiedersi all'utente di prendere gli adeguati
provvedimenti.

norme sulle emissioni e sull’immunità. In caso di uso senza cavi schermati, l’utente
può dover adottare a proprie spese misure correttive contro le interferenze.

Questo è un “PRODOTTO CON LED DI CLASSE 1”
NORME DI SICUREZZA

PERICOLO

PRECIPITAZIONI TEMPORALESCHE.
NON OSTRUIRE LE PRESE D'ARIA
Questo dispositivo deve essere alimentato solo mediante l’adattatore.

EUROPE - EU

Utilizzare l’adattatore per c.a. da 12 V c.c. e 500 mA conforme alla normativa TÜV.

Questo prodotto è concepito per una temperatura ambientale massima di 40 gradi
centigradi.

elettriche nazionali.

: Questo prodotto è conforme ai seguenti standard.

: in ambiente domestico questo prodotto potrebbe causare radio

: questo prodotto, se utilizzato con cavi schermati, è conforme alle

Prodotto laser di Classe 1.

Non fissare il raggio con gli occhi.

: NON LAVORARE sul dispositivo o sui CAVI durante

: installare il prodotto in conformità delle vigenti normative

EN55022 Classe

EN50082-1 1997

EN60950, UL1950, CSA 950
EN60825

A

32

AT-FS200 Series Installation Guide

Sikkerhetsnormer



1 RFI stråling



2 Advarsel



3 Immunitet



4 Advarsel



5 Elektrisk sikkerhet



6Laser



7ADVARSEL



8ADVARSAL



9



10 FARE FOR LYNNEDSLAG



11



12



13 DRIFTSTEMPERATUR



14 ALLE LAND



1 Emissão De Interferência De



2 Aviso



3Imunidade



4 Advertência



5 Segurança Eléctrica



6Laser



7 Aviso



8 Aviso



9



10 PERIGO DE CHOQUE CAUSADO POR RAIO



11



12

radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler.

emisjons- og fritakelsesstandarder. Dersom produktet brukes med uvernede kabler,
må brukeren muligens rette forstyrrelsesproblemene for egen regning.

Dette er et “KLASSE 1 LED PRODUKT”

SIKKERHET

FARE

BLOKKER IKKE LUFTVENTILENE
All strømtilførsel må komme fra adapteren.

EUROPE - EU

Benytt TÜV-godkjent AC-adapter på 12V DC, 500mA (millismpere)

Dette produktet er konstruert for bruk i maksimum romtemperatur på 40 grader
celsius.

elektriske koder.

Padrões

Radiofrequência

radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas
adequadas.

cumprimento dos standards de limites de emissão e imunidade. Se o produto for
utilizado com cabos não blindados, o utilizador poderá necessitar de tomar medidas
para correcção de problemas de interferência, por sua própria conta.

Este é um “PRODUTO CLASSE 1 LED”

SEGURANÇA

PERIGO

suscetíveis a QUEDAS DE RAIO.
NÃO BLOQUEIE AS ABERTURAS DE VENTILAÇÃO
Use somente o adaptador fornecido para alimentação elétrica do hub.

: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake

: Dette produktet må brukes med vernede kabler for å tilfredsstille

: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.

: Este produto atende aos seguintes padrões.

: Num ambiente doméstico este produto pode causar interferência na

Produto laser de classe 1.
Não olhe fixamente para o raio.

: NÃO TRABALHE no equipamento ou nos CABOS durante períodos

: Dette produktet tilfredsstiller følgende sikkerhetsnormer.

Laserprodukt av klasse 1.
Stirr ikke på strålen.

: Produktet må installeres i samsvar med de lokale og nasjonale

: Este produto requer a utilização de cabos blindados para

EN55022 Klasse A

EN50082-1 1997

EN60950, UL1950, CSA 950
EN60825

EN55022 Classe

EN50082-1 1997

TUV-EN60950, UL1950, CSA 950
EN60825

A

33

Electrical Safety and Installation Requirements

EUROPE - EU

Use um adaptador de corrente alternada com saída DC de 12V e 500mA em
conformidade com as especificações da TÜV.



13 TEMPERATURA DE FUNCIONAMENTO



14 TODOS OS PAÍSES

Este produto foi projetado para uma temperatura ambiente máxima de 40 graus
centígrados.

para instalações elétricas.

: Instale o produto de acordo com as normas nacionais e locais

Estándares



1 Emisión RFI



2 Advertencia



3 Inmunidad



4 Advertencia



5 Seguridad eléctrica



6Laser



7 ¡ADVERTENCIA!



8 ¡ADVERTENCIA!



9



10 PELIGRO DE RAYOS



11



12



13 TEMPERATURA REQUERIDA PARA LA OPERACIÓN



14 PARA TODOS LOS PAÍSES

radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas
que sean convenientes al respecto.

emisión e inmunidad. Si se utiliza con cables sin protección, el usuario tendrá que
correr con los gastos por las medidas a tomar en caso de problemas de interferencias.

Este es un “PRODUCTO DE DIODO LUMINISCENTE (LED) CLASE 1”

SEGURIDAD

ELIGRO

equipos o en LOS CABLES durante TORMENTAS ELECTRICAS.
NO BLOQUEE LAS ABERTURAS PARA VENTILACION
La energía para el dispositivo central o "hub" debe provenir únicamente del

adaptador.

EUROPE - EU

Utilizar un adaptador de corriente alterna autorizado TÜV de 12 voltios de corriente
continua y 500 miliamperios.

Este producto está diseñado para una temperatura ambiental máxima de 40 grados
C.

Eléctricos locales y nacionales.

: Este producto cumple con los siguientes estándares.

EN55022 Clase

: en un entorno doméstico, este producto puede causar

EN50082-1 1997

: Este producto exige cables protectores para ajustarse a las normas de

TUV-EN60950, UL1950, CSA 950
EN60825

Producto láser Clase 1.

No mirat fijamente el haz.

: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los

: Monte el producto de acuerdo con los Códigos

A

34

AT-FS200 Series Installation Guide

Standarder



1 Radiostörning



2 Varning



3 Immunitet



4 Varning



5Elsäkerhet



6Laser



7VARNING!



8VARNING!



9



10 FARA FÖR BLIXTNEDSLAG



11



12



13 DRIFTSTEMPERATUR



14 ALLA LÄNDER

tvinga användaren till att vidtaga erforderliga åtgärder.

för emission och immunitet. Om den används med oskärmade kablar kan
användaren vara tvungen att vidta åtgärder på egen bekostnad för att åtgärda
störningsproblemet.

Detta är en “KLASS 1 LYSDIODPRODUKT”

SÄKERHET

FARA

BLOCKERA INTE LUFTVENTILERN
Endast anslutningsenheten får vara kraftkälla till centralen.

EUROPE - EU

Använd en växelströmsanslutningsenhet licensierad av TÜV. Likström 12V, 500mA.

Denna produkt är konstruerad för rumstemperatur ej överstigande 40 grader
Celsius.

bestämmelser för elektrisk utrustning.

: Denna produkt uppfyller följande standarder.

: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan

! Denna produkt kräver skärmade kablar för att uppfylla standardkraven

Laserprodukt av klass 1.
Laserstrålning när enheten är öppen.

: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER.

: Installera produkten i enlighet med lokala och statliga

EN55022 Klass A

EN50082-1 1997

TUV-EN60950, UL1950, CSA 950
EN60825

35

Appendix C

Technical Support Fax Order

Name __________________________________________________________________

Company _______________________________________________________________

Address ________________________________________________________________

City ________________________ State/Province _______________________________

Zip/Postal Code ____________________ Country _______________________________

Phone _______________________________ Fax_______________________________

Incident Summary

Model number of Allied Telesyn product I am using _______________________________

Network software products I am using ________________________________________

______________________________________________________________________

Brief summary of problem __________________________________________________

______________________________________________________________________

Conditions (List the steps that led up to the problem.) _____________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

Detailed description (Use separate sheet, if necessary)

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

When completed, fax this sheet to the appropriate Allied Telesyn office. Fax numbers can be
found on page viii.

37

Appendix D

AT-FS201, AT-FS202 and AT-FS203 Series Installation Guide Feedback

Please tell us what additional information you would like to see discussed in
the guide. If there are topics you would like information on that were not
covered in the guide, please photocopy this page, answer the questions and fax
or mail this form back to Allied Telesyn. The mailing address and fax number
are at the bottom of the page. Your comments are valuable when we plan future
revisions of the guide.

I found the following the most valuable __________________________________

______________________________________________________________________
______________________________________________________________________
______________________________________________________________________

I would like the following more developed ________________________________

______________________________________________________________________
______________________________________________________________________
______________________________________________________________________

I would find the guide more useful if _____________________________________

______________________________________________________________________
______________________________________________________________________
______________________________________________________________________

Please fax or mail your feedback. Fax to 1-408-736-0100. Or mail to:

Allied Telesyn International, Corp.

c/o Technical Communications
960 Stewart Drive, Suite B
Sunnyvale, CA 94086 USA

PN 613-10761-00 Rev B

39