AT-FS201
AT-FS202
AT-FS202SC/FS1
AT-FS202SC/FS2
AT-FS202SC/FS3
AT-FS202SC/FS4
Fast Ethernet Switches
Installation Guide
PN 613-10761-00 Rev C
Copyright 2001 Allied Telesyn International Corp.
960 Stewart Drive, Suite B, Sunnyvale CA 94086 USA
All rights reserved. No part of this publication may be reproduced without prior
written permission from Allied Telesyn International Corp.
Ethernet is a registered trademark of Xerox Corporation. All other product names,
company names, logos or other designations mentioned herein are trademarks or
registered trademarks of their respective owners.
Allied Telesyn International Corp. reserves the right to make changes in specifications
and other information contained in this document without prior written notice. The
information provided herein is subject to change without notice. In no event shall Allied
Telesyn International Corp. be liable for any incidental, special, indirect, or
consequential damages whatsoever, including but not limited to lost profits, arising out
of or related to this manual or the information contained herein, even if Allied Telesyn
International Corp. has been advised of, known, or should have known, the possibility of
such damages.
Safety Warnings
Standards: This product meets the following standards.
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with this instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the
FCC, can void your right to operate this equipment.
This Class A digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur
le matériel brouilleur du Canada.
Industry Canada
RFI Emission EN55022 Class A
Warning: In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Immunity EN55024
Warning: This product requires shielded cables to comply with emission and immunity
standards. If it is used with unshielded cables, the user may be required to take measures
to correct the interference problem at their own expense.
Electrical Safety EN60950, UL1950, CSA 950
Laser EN60825
Warning Class 1 Laser product.
Warning Do not stare into the Laser beam.
At time of installation, the Fiber Optic Lasers comply with FDA Radiation Performance
Standard 21CFR Subchapter J, applicable at date of manufacture.
This is a “CLASS 1 LED PRODUCT” (AT-FS201, AT-FS202 models)
Important: Appendix B contains translated safety statements for installing this
equipment. When you see the
your language.
Wichtig: Anhang B enthält übersetzte Sicherheitshinweise für die Installation dieses
Geräts. Wenn Sie
Sicherheitshinweis in Ihrer Sprache nach.
Vigtigt: Tillæg B indeholder oversatte sikkerhedsadvarsler, der vedrører installation af
dette udstyr. Når De ser symbolet
sikkerhedsadvarsler i Deres eget sprog.
Belangrijk: Appendix B bevat vertaalde veiligheidsopmerkingen voor het installeren van
deze apparatuur. Wanneer u de
veiligheidsinstructies in uw taal.
$ sehen, schlagen Sie in Anhang B den übersetzten
$ 7
$ 8
$, go to Appendix B for the translated safety statement in
$, skal De slå op i tillæg B og finde de oversatte
$ ziet, raadpleeg Appendix B voor vertaalde
$ 1
$ 2
$ 3
$ 4
$ 5
$ 6
$ 9
iii
Safety Wa rnings
Important: L'annexe B contient les instructions de sécurité relatives à l'installation de cet
équipement. Lorsque vous voyez le symbole
la traduction de ces instructions dans votre langue.
Tärkeää: Liite B sisältää tämän laitteen asentamiseen liittyvät käännetyt turvaohjeet.
Kun näet
Importante: l’Appendice B contiene avvisi di sicurezza tradotti per l’installazione di
questa apparecchiatura. Il simbolo
sicurezza nella propria lingua.
Viktig: Tillegg B inneholder oversatt sikkerhetsinformasjon for installering av dette
utstyret. Når du ser
sikkerhetsinformasjonen på ønsket språk.
Importante: O Anexo B contém advertências de segurança traduzidas para instalar este
equipamento. Quando vir o símbolo
idioma no Anexo B.
Importante: El Apéndice B contiene mensajes de seguridad traducidos para la
instalación de este equipo. Cuando vea el símbolo
mensaje de seguridad traducido a su idioma.
Obs! Bilaga B innehåller översatta säkerhetsmeddelanden avseende installationen av
denna utrustning. När du ser
säkerhetsmeddelandet på ditt språk.
$, reportez-vous à l'annexe B pour consulter
$-symbolin, katso käännettyä turvaohjetta liitteestä B.
$, indica di consultare l’Appendice B per l’avviso di
$, åpner du til Tillegg B for å finne den oversatte
$, leia a advertência de segurança traduzida no seu
$, vaya al Apéndice B para ver el
$, skall du gå till Bilaga B för att läsa det översatta
iv
Table of Contents
Safety Warnings ............................................................................................iii
Welcome to Allied Telesyn .........................................................................vii
Where to Find Web-based Guides ...................................................................vii
Document Conventions ....................................................................................vii
Contacting Allied Telesyn Technical Support................................................viii
Online Support .........................................................................................viii
Telephone and Fax Support.....................................................................viii
Technical Support E-mail Addresses ........................................................ix
Returning Products ...........................................................................................ix
FTP Server.........................................................................................................ix
For Sales or Corporate Information .................................................................. x
Tell Us What You Think .................................................................................... x
Chapter 1
Description ......................................................................................................1
Features ..............................................................................................................3
Status LEDs ................................................................................................ 4
External AC/DC Power Adapter.................................................................4
Twisted Pair Port................................................................................................5
Port Speed....................................................................................................5
Duplex Mode................................................................................................5
Auto MDI/MDI-X.........................................................................................5
Fiber Optic Port..................................................................................................6
Port Speed....................................................................................................6
Duplex Mode................................................................................................6
Switch Performance............................................................................................6
DIP Switches ...............................................................................................7
MAC Address Table.....................................................................................7
Store and Forward....................................................................................... 7
Network Topologies............................................................................................ 8
Chapter 2
Installing the Switch ..................................................................................... 9
Verifying the Package Contents ........................................................................ 9
Planning the Installation.................................................................................10
Selecting a Site .................................................................................................12
Installing the Switch........................................................................................12
Warranty Registration.....................................................................................14
v
Table of Contents
Chapter 3
Troubleshooting ...........................................................................................15
Appendix A
Technical Specifications ............................................................................17
Physical .............................................................................................................17
Temperature .....................................................................................................17
Electrical Rating...............................................................................................17
Agency Certifications........................................................................................17
Transmitter.......................................................................................................18
Fiber Optic Port Specifications ........................................................................18
Pinout Assignments..........................................................................................20
Appendix B
Electrical Safety and Installation Requirements .................................21
Appendix C
Technical Support Fax Order ...................................................................31
Incident Summary............................................................................................31
vi
Welcome to Allied Telesyn
This guide contains instructions on how to install the AT-FS20x and
AT-FS202SC/FSx Series Fast Ethernet Switches.
Where to Find Web-based Guides
The Allied Telesyn web site at www.alliedtelesyn.com provides you with an
easy way to access the most recent documentation, software, and technical
information for all of our products. For product guides, select “Support &
Services” from our web site.
Document Conventions
This guide uses several conventions that you should become familiar with
before you begin to install the product.
Note
A note provides additional information.
Caution
A caution indicates that performing or omitting a specific action may
result in equipment damage or loss of data.
Warning
A warning indicates that performing or omitting a specific action may
result in bodily injury.
vii
Welcome to Allied Telesyn
Contacting Allied Telesyn Technical Support
You can contact Allied Telesyn technical support online or by telephone, fax,
or e-mail.
Online Suppo rt
You can request technical support online by filling out the Technical Enquiry
Form or by accessing the Knowledge Base. You can use the Knowledge Base to
submit questions to our technical support staff and review answers to
previously asked questions.
To access the Knowledge Base, select “Support & Services”, then “Help” from
www.alliedtelesyn.com. To access the Technical Enquiry Form, select
“Contact Us”.
Telephone and Fax Support
For Technical Support via fax, please fill out the “Technical Support Fax
Order” on page 31 and send it to the appropriate location listed below.
Americas
United States, Canada, Mexico,
Central America, South America
Tel: 1 (800) 428-4835, option 4
Fax: 1 (425) 481-3790
Asia
Singapore, Taiwan, Thailand, Malaysia,
Indonesia, Korea, Philippines, China,
India, Hong Kong
Tel: (+65) 3815-612
Fax: (+65) 3833-830
Australia
Tel: 1 (800) 000-880
Fax: (+61) 2-9438-4966
France
France, Belgium, Luxembourg,
The Netherlands, Middle East, Africa
Tel: (+33) 0-1-60-92-15-25
Fax: (+33) 0-1-69-28-37-49
viii
Germany
Germany, Switzerland, Austria, Eastern
Europe
Tel: (+49) 30-435-900-126
Fax: (+49) 30-435-70-650
Italy
Italy, Spain, Portugal, Greece, Turkey,
l
Israe
Tel: (+39) 02-41-30-41
Fax: (+39) 02-41-30-42-00
Japan
Tel: (+81) 3-3443-5640
Fax: (+81) 3-3443-2443
United Kingdom
United Kingdom, Denmark, Norway,
Sweden, Finland
Tel: (+0044) 1235-442500
Fax: (+44) 1-235-442680
AT-FS20x and AT-FS202SC/FSx Series Installation Guide
Technical Support E-mail Addresses
United States and Canada
TS1@alliedtelesyn.com
Latin America, Mexico, Puerto Rico, Caribbean, and Virgin Islands
latin_america@alliedtelesyn.com
Europe
support_europe@alliedtelesyn.com
Returning Products
Products for return or repair must first be assigned a Return Materials
Authorization (RMA) number. A product sent to Allied Telesyn without a
RMA number will be returned to the sender at the sender’s expense.
To obtain an RMA number, contact Allied Telesyn’s Technical Support at one
of the following locations:
North America
Toll-free: 1-800-428-4835, option 4
Fax: 1-425-481-3790
Latin America, the Caribbean, and
Virgin Islands
Tel: international code + 425-481-3852
Fax: international code + 425-481-3895
Mexico
Toll-free: 800-424-5012, ext 3852
Fax: international code + 425-481-3895
Australia
Toll-free: 1-800-000-880
Fax: +61-2-9438-4966
Europe, Africa, and the Middle East
Tel: +44-1793-501401
Fax: +44-1793-431099
Puerto Rico
Tel: 1-800-424-5012, ext 3852 or
1-800-424-4284, ext 385
Asia and Southeast Asia
Tel: +65-381-5612
Fax: +65-383-3830
New Zealand
Toll-free: 0800-45-5782
2
FTP Server
If you need management software for an Allied Telesyn managed device and
you know the file name of the software, you can download the software by
connecting directly to our FTP server at ftp.alliedtelesyn.com. At login,
enter ‘anonymous’ as the user name and your e-mail address for the password.
ix
Welcome to Allied Telesyn
For Sales or Corporate Information
You can contact Allied Telesyn for sales or corporate information at the
location listed below:
Allied Teleyn International Corp.
19800 North Creek Parkway, Suite 200
Bothell, WA 98011
Tel: 1 (425) 487-8880
Fax: 1 (425) 489-9191
Tell Us What You Think
If you have any comments or suggestions on how we might improve this or
other Allied Telesyn documents, please fill out the General Enquiry Form
online. This form can be accessed by selecting “Contact Us” from
www.alliedtelesyn.com.
x
Chapter 1
Description
The AT-FS20x and AT-FS202SC/FSx Series Fast Ethernet Switches include
the following models:
❑ AT-FS201 ❑ AT-FS202SC/FS2
❑ AT-FS202 ❑ AT-FS202SC/FS3
❑ AT-FS202SC/FS1 ❑ AT-FS202SC/FS4
The AT-FS20x and AT-FS202SC/FSx Series Switches are designed to extend
the distance of your network by converting Fast Ethernet data between
twisted pair cabling and either multimode or single-mode fiber optic cabling.
These dual-port switches can also be used to improve the performance of your
network by dividing it into smaller, more manageable segments.
Each switch features a 100Base-FX fiber optic port and a 10/100Base-TX
twisted pair port. The fiber optic port has either a SC or ST connector and a
maximum operating distance of 2 kilometers (1.2 miles) to 100 kilometers (62
miles), depending on the model. The twisted pair port has a RJ-45 connector
with a maximum operating distance of 100 meters (328 feet).
The fiber optic port operates at 100 Mbps, while the twisted pair port operates
at 10 Mbps or 100 Mbps. Both ports feature half- and full-duplex operation.
AT-FS20x and AT-FS202SC/FSx Series Switches can be installed on a desktop
or in an AT-MCR12 chassis. These switches are easy to install and do not
require software configuration or management.
1
Description
Figure 1 illustrates the front panel of an AT-FS20x Series Switch.
100Base-FX
LNK/
ACT
FD/ COL
PORT 1
TX RX
10Base-T/
100Base-TX
PORT 2
LNK/
ACT
FD/
COL
PWR
AUTO
NEG
100M
AT-FS202 FAST ETHERNET SWITCH IEEE 802.3/802.3U
Figure 1 AT-FS20x Series Front Panel (AT-FS202 Model)
Figure 2 illustrates a front panel of an AT-FS202SC/FSx Series Switch.
100Base-FX
LNK/
ACT
FD/ COL
PORT 1
SINGLE MODE
TX RX
CLASS 1
LASER PRODUCT
DO NOT STARE
INTO BEAM
10Base-T/
100Base-TX
PORT 2
LNK/
ACT
COL
PWR
AUTO
NEG
FD/
100M
AT-FS202SC/FS4 FAST ETHERNET SWITCH IEEE 802.3/802.3U
Figure 2 AT-FS202SC/FSx Series Front Panel (AT-FS202SC/FS4 Model)
The back panel of the AT-FS20x and AT-FS202SC/FSx Series Switches
features a power adapter connector and DIP switches for manually
configuring the ports. Figure 3 illustrates the back panel.
DIP Switches
PORT
1222
21 34
DUPLEX
12VDC
SPEED
(Mbps)
10
100
MODE
HALF
FULL
AUTO
NEG
OFF
ON
Power Adapter Connector
Figure 3 Back Panel of the AT-FS20x and AT-FS202SC/FSx Series Switches
2
AT-FS20x and AT-FS202SC/FSx Series Installation Guide
Table 1 lists the maximum operating distances for the switches.
Table 1 Maximum Operating Distances
100Base-FX 10/100Base-TX
Model
Connector
Maximum
Operating
Distance
Maximum
1
Connector
Operating
Distance
2
AT-FS201 ST 2 km (1.2 mi) RJ-45 100 m (328 ft)
AT-FS202 SC 2 km (1.2 mi) RJ-45 100 m (328 ft)
AT-FS202SC/FS1 SC 15 km (9.3 mi) RJ-45 100 m (328 ft)
AT-FS202SC/FS2 SC 40 km (24.8 mi) RJ-45 100 m (328 ft)
AT-FS202SC/FS3 SC 75 km (46.5 mi) RJ-45 100 m (328 ft)
AT-FS202SC/FS 4 SC 100 km (62 mi) RJ-45 100 m (328 ft)
1. Maximum distance for 100 Mbps optical datalinks is dependent on the following factors: type of optical fiber,
duplex mode of both end-nodes, and maximum optical loss budget for each of the optical fiber at the operating
optical wavelength.
2. Maximum distance can only be obtained when the UTP/STP cabling is installed and verified to TIA/EIA 568A
Commercial Building Telecommunications Cabling Standard.
Features
The AT-FS20x and AT-FS202SC/FSx Series Switches have the following
features:
❑ LEDs for unit and port status
❑ Auto MDI/MDI-X
❑ External AC/DC power adapters (North America, Continental Europe,
or United Kingdom)
❑ DIP switches for configuring the ports
❑ Half- or full-duplex operation on both ports
❑ RJ-45 twisted pair connector
❑ SC or ST fiber optic connector
❑ Data packet forwarding and filtering at full wire speed (10 Mbps to
100 Mbps, 100 Mbps to 100 Mbps, and 10 Mbps to 10 Mbps)
3
Description
❑ Store and forward switching mode
❑ Automatic address learning and aging
❑ IEEE 802.3u compliant auto-negotiation
❑ For use on a desktop or in an AT-MCR12 chassis
Status LEDs
Table 2 defines the LEDs for the switches.
Table 2 LEDs
LED Color Description
PWR Green Power is applied to the switch.
LNK/ACT Green
Blinking
100M Green
OFF
FD/COL Green
OFF
Blinking
AUTO NEG Green
OFF
A valid link has been esta blished on the port.
Data is being received or transmitted on the port.
The twisted pair port is operating at 100 Mbps.
The twisted pair port is operating at 10 Mbps.
The switch is operating in f ull-duplex mode.
The switch is operating in half-duplex mode.
A collision has been detected on the port.
Auto-negotiation on the twisted pair port is enabled.
Auto-negotiation on the twisted pair port is disabled.
External AC/DC Power Ad apter
The power adapter supplies 12V DC to the switch. Allied Telesyn supplies an
approved safety compliant AC power adapter for the 100 and 240V AC
versions with an unregulated output of 12V DC.
4
AT-FS20x and AT-FS202SC/FSx Series Installation Guide
Twisted Pair Port
The AT-FS20x and AT-FS202SC/FSx Series Switches have one 10/
100Base-TX twisted pair port. The twisted pair port features a RJ-45
connector.
Port Speed
The twisted pair port is compliant with the 10Base-T and 10Base-TX
standards and is capable of either 10 Mbps or 100 Mbps operation. You can set
the port speed manually or, since the port is IEEE 802.3u auto-negotiation
compliant, you can allow the switch to set the port speed automatically. With
auto-negotiation, the speed of the port is set automatically by the switch after
it determines the speed of the end-node connected to the port. Autonegotiation is designed to ensure that the port on the switch and the end-node
are operating at the same speed and that they are communicating at the
highest possible common speed of the devices.
Duplex Mode
Duplex mode refers to the way an end-node sends and receives data on the
network. An end-node can operate in either half- or full-duplex mode,
depending on its capabilities. An end-node that is operating in half-duplex
mode can either send data or receive data, but it cannot do both at the same
time. An end-node that is operating in full-duplex mode can send and receive
data simultaneously. The best network performance is achieved when an endnode can operate at full-duplex, since the end-node is able to send and receive
data simultaneously.
The twisted pair port on the switch can operated in either half- or full-duplex
mode. You can set the duplex mode manually or allow the switch to set it
automatically through auto-negotiation. With auto-negotiation, if the endnode is capable of full-duplex, the twisted pair port is set automatically to fullduplex mode. If the end-node is capable of half-duplex, the port is set
automatically to half-duplex mode.
Auto MDI/MDI-X
An RJ-45 twisted pair port on a 10 Mbps or 100 Mbps Ethernet network
device can have one of two possible wiring configurations: MDI or MDI-X. The
RJ-45 port on a PC, router, or bridge is typically wired as MDI, while the
twisted pair port on a switch or hub is usually MDI-X.
5
Description
To connect two 10 Mbps or 100 Mbps network devices together that have
dissimilar port wiring configurations, such as MDI to MDI-X, you would
usually use a straight-through twisted pair cable. To connect two network
devices that have the same wiring configuration, such as MDI to MDI, you
would usually use a crossover cable.
The AT-FS20x and AT-FS202SC/FSx Series Switches feature automatic MDI/
MDI-X. The RJ-45 port automatically determines the configuration of the port
on the device to which it is connected and then configures itself appropriately.
For example, if a port on a switch is connected to a port on a bridge, which is
typically wired as MDI, the port on the switch automatically configures itself
as MDI-X. This feature allows you to use either crossover cables or straightthrough cable when connecting a device to the twisted pair port.
Fiber Optic Port
The AT-FS20x and AT-FS202SC/FSx Series Switches have one 100Base-FX
fiber optic port. The fiber optic port features either an SC or ST connector.
Port Speed
The fiber optic port is compliant with the 100Base-FX standard and has a
fixed operating speed of 100 Mbps. The end-node connected to the fiber optic
port on the switch must also be able to operate at 100 Mbps.
Duplex Mode
The fiber optic port on the switch can operate in half- or full-duplex mode. You
must set the duplex mode manually using the DIP switches on the back of the
unit.
Switch Performance
The switches perform at:
❑ 148,800 pps for 100 Mbps and 14,880 pps for 10 Mbps for full wire
speed forwarding and filtering
❑ 200 Mbps maximum throughput in 100 Mbps, full-duplex mode
❑ 20 Mbps maximum throughput in 10 Mbps, full-duplex mode
❑ Storage for up to 4,000 MAC addresses
❑ 280 kib bytes (per port) packet buffer
❑ Low latency 15.6 µs (64-byte packet, 100 Mbps full-duplex)
6
AT-FS20x and AT-FS202SC/FSx Series Installation Guide
DIP Switches
The DIP switches are used to manually configure the operating characteristics
of the ports. These characteristics include the port speed, duplex mode, and
auto-negotiation.
On the 100Base-FX fiber optic port, you can manually set the duplex mode to
either half- or full-duplex.
On the 10/100Base-TX twisted pair port, you can manually set the speed of
the port to either 10 Mbps or 100 Mbps, set the duplex mode to either half- or
full-duplex and enable or disable auto-negotiation. Enabling auto-negotiation
will automatically set the port’s speed and duplex mode.
MAC Address Table
Up to 4,000 MAC addresses can be stored in the switch’s MAC address table.
The switch’s self-learning feature will learn all new addresses in real-time
after power-up. If the source address of an incoming packet is not found in the
MAC address table, the switch will update the table with the new address.
The switch also has an automatic address aging feature that will delete a
source address from the table if it has not seen a frame from the end-node
with that address within five minutes. This prevents the table from becoming
filled with addresses of end-nodes that are no longer active.
The switch forwards all multicast, broadcast, and unicast packets when the
MAC address table has exceeded its storage limit.
Store and Forward
The AT-FS20x and AT-FS202SC/FSx Series Switches support store and
forward switching at Fast Ethernet full-wire speed in 100 Mbps, half- or fullduplex mode. Packets entering each port are stored in buffers. Once the full
packet is received, the switch will forward or discard the packet, depending on
its destination address and error status. This ensures that only error-free
packets destined for another segment will be transferred across the switch,
reducing network load. For example, if the packet entering from Port 1 is
destined for an end-node on Port 2, the switch forwards the frame if the frame
does not contain any errors. If the packet from Port 1 is destined for an endnode also connected to Port 1, the packet is discarded.
The switch will discard CRC errors, misaligned, runt, and under-oversized
packets. When the packet has dribble bits at the end, the switch will truncate
to octet boundary and check for a good FCS before forwarding.
7
Description
Network Topologies
Figure 4 illustrates a topology using one AT-FS201 switch to interconnect two
small networks of stackable hubs. Network 1 has an AT-FH812u with an
AT-FH807u switching module connected to the 100Base-FX port on the
AT-FS201. Network 2 has an AT-3624TR hub connected to the 10/100Base-TX
port on the AT-FS201.
AT-FH812u
with an
AT-FH807u
module
Network 1
AT-FH812u
AT-FH812u
Network 2
AT-3624TR
AT-3624TR
AT-3624TR
AT-FS201
Twisted Pair
Fiber Optic
Figure 4 Network Topology
8
Chapter 2
Installing the Switch
This chapter explains how to install an AT-FS20x or AT-FS202SC/FSx Series
Switch. These switches can be installed on a desktop or in an AT-MCR12
chassis.
Verifying the Package Contents
Make sure the following items are included in your package. If any item is
missing or damaged, contact your Allied Telesyn sales representative for
assistance.
❑ One AT-FS20x or AT-FS202SC/FSx Series Switch
❑ Four protective feet (for desktop use only)
❑ External AC/DC power adapter (North America, Continental Europe,
or United Kingdom)
❑ This installation guide
❑ Warranty card
9
Installing the S witch
Planning the Installation
Be sure to observe the following guidelines when planning the installation of
your switch.
❑ The end-node connected to the 100Base-FX fiber optic port must be
able to operate at 100 Mbps.
❑ The end-node connected to the 10/100Base-TX twisted pair port can
operate at either 10 Mbps or 100 Mbps.
❑ The end-node connected to a port on the switch can be a network
adapter card, repeater, router, hub, or another switch.
❑ The twisted pair cabling must be kept away from sources of electrical
noise, such as radios, transmitters, power lines, broadband amplifiers,
electrical motor, and fluorescent fixtures.
❑ Refer to Table 3 for the cabling specifications for the twisted pair port.
Table 3 10/100Base-TX Twisted Pair Cabling Specifications
Operating Mode Twisted Pair Cable
10Base-T Shielded or unshielded Ca te go r y 3 or bette r 100 m (328 ft)
100Base-TX Shielded or uns hie l de d Ca te go r y 5 or bette r 100 m (328 ft)
Maximum Operating
Distance
❑ Refer to Table 4 for the cabling specifications for the fiber optic port
operating in full-duplex mode.
Table 4 100Base-FX Fiber Optic Cabling Specif ications (Full-duplex)
Model
AT-FS201 50/125 or
AT-FS202 50/125 or
Fiber Optic
Cable
62.5/125 micron
multimode
62.5/125 micron
multimode
Maximum Operating
Distance
2 km (1.2 mi) 13 dB at 1310 nm
2 km (1.2 mi) 13 dB at 1310 nm
1
Maximum
Allowable Loss
Budget
10
AT-FS20x and AT-FS202SC/FSx Series Installation Guide
Table 4 100Base-FX Fiber Optic Cabling Spec ifications (Full-duplex) - continued
Model
Fiber Optic
Cable
AT-FS202SC/FS1 50/125 or 62.5/
Maximum Operating
Distance
1
2 km (1.2 mi) 13 dB at 1310 nm
Maximum
Allowable Loss
Budget
125 multimode
9/125 micron
15 km (9.3 mi) 16 dB at 1310 nm
single-mode
AT-FS202SC/F S2 9/125 micron
40 km (24.8 mi) 30 dB at 1310 nm
single-mode
AT-FS202SC/F S3 9/125 micron
75 km (46.5 mi) 33 dB at 1310 nm
single-mode
AT-FS202SC/FS4
2
9/125 micron
100 km (62 mi) 34 dB at 1 550 nm
single-mode
1. Maximum distance for 100 Mbps optical datalinks is dependent on the following factors: type of optical fiber,
duplex mode of both end-nodes, and maximum optical loss budget for each of the optical fiber at the operating
optical wavelength.
2. The cable must be non-dispersion-shifted, dispersion-shifted, or non-zero dispersion-shifted single-mode fiber
optic cable.
Note
Refer to “Fiber Optic Port Specifications” on page 18 for additional
information on the fiber optic port.
❑ Refer to Table 5 for the cabling specifications for the fiber optic port
operating in half-duplex mode.
Table 5 100Base-FX Fiber Optic Ports (Half-duplex)
Number of Media
Converters
Connected Device s
One Media Converter Inline Switch to switch 372 m (1,221 ft)
Workstation to switch 372 m (1,221 ft)
Switch to Class I repeater 137 m (450 ft)
Switch to Class II repeater 185 m (607 ft)
1
Maximum Operating
Distance
11
Installing the S witch
Table 5 100Base-FX Fibe r Op ti c Ports (Half-duplex)1 - continued
Number of Media
Converters
Two Media Converters
Inline
1. The total distance of the fiber optic lengths cannot exceed the limits stated in the table. Each media converter used
inline within a single collision domain reduces the overall segment length by 40 meters (131 feet).
Connected Device s
Switch to switch 332 m (1,089 ft)
Workstation to switch 322 m (1, 089 ft)
Switch to Class I repeater 97 m (318 ft)
Switch to Class II repeater 145 m (476 ft)
Maximum Operating
Distance
Selecting a Site
Be sure to observe the following guidelines when selecting a site for your
switch.
❑ Select a site that is dust-free and moisture-free.
❑ Select a site that will allow you to easily access the data cables and
power cord.
❑ Use dedicated power circuits or power conditioners to supply reliable
power to the device.
Installing the Switch
To install an AT-FS20x or AT-FS202SC/FSx Series Switch, perform the
following procedures:
1. Remove all equipment from the package and store the packaging in a safe
place.
Note
Do not remove the dust cover from the fiber optic port until you are
ready to connect the fiber optic cable. Dust contamination can adversely
impact the operating performance of the port and the switch.
2. Attach the four protective feet (provided) to each corner of the base of the
unit. Do not attach the protective feet if you are installing the
switch in an AT-MCR12 chassis.
12
AT-FS20x and AT-FS202SC/FSx Series Installation Guide
3. Configure the DIP switches. Refer to Figure 3 on page 2 for the location of
the DIP switches and Table 6 for the possible settings.
Table 6 DIP Switch Settings
DIP
Switch
Port Setting Position Description
Number
12Speed (Mbps)Up
The twisted pair por t is op e rating at 10
Mbps.
Down
The twisted pair por t is op e rating at 100
Mbps.
2 1 Duplex Mode Up
The fiber optic port is operating at halfduplex mode.
Down
The fiber optic is operating at full-duplex
mode.
3 2 Duplex Mode Up
The twisted pair por t is op e rating at halfduplex mode.
Down
The twisted pair por t is op e rating at fullduplex mode.
42Auto NegUp
Auto-negotiation on the twisted pair port is
OFF.
Down
Auto-negotiation on the twisted pair port is
ON.
When setting the DIP switches, consider the following:
❑ Setting the Auto Neg DIP switch for the twisted pair port to ON or
OFF enables or disables auto-negotiation for the port. If you disable
auto-negotiation, be sure to set the DIP switches for the port’s speed
and duplex mode to match the speed and duplex mode of the end-node.
❑ For the fiber optic port, set the port’s duplex mode using the
appropriate Duplex Mode DIP switch. This setting must match the
duplex mode capability of the end-node to be connected to the port.
4. If you are installing the switch in an AT-MCR12 chassis, refer to the
chassis’ installation guide for instructions on how to install the switch,
then proceed to Step 7.
13
Installing the S witch
5. Place the switch on a secure, level surface, leaving ample space around
the unit for ventilation.
6. Plug the AC/DC power adapter into an appropriate AC power outlet and
insert the power plug into the DC receptacle located on the back panel.
This step does not apply if you are installing the switch in an
AT-MCR12 chassis.
7. Verify that the PWR LED is green. If the LED is OFF, refer to
“Troubleshooting” on page 15 for instructions.
8. Remove the dust cover from the fiber optic port and connect the fiber optic
cable to the 100Base-FX port.
9. Connect the twisted pair cable to the 10/100Base-TX port.
10. Power ON the end-nodes.
11. Verify that the LNK/ACT LEDs for both the fiber optic port and the
twisted pair port are green. If either LED is OFF, refer to
“Troubleshooting” on page 15 for instructions.
12. The switch is now ready for use.
Warranty Registration
When you have finished installing the product, register your product by
completing the enclosed warranty card and sending it in. You can also fill out
the registration online by selecting “Warranties” under “Support & Services”
from www.alliedtelesyn.com.
14
Chapter 3
Troubleshooting
Follow the guidelines below to test and troubleshoot the installation in the
event a problem occurs.
Note
Whenever the speed and/or duplex mode are changed during or after
power ON, power OFF then power back ON the switch to load the new
configuration.
If the PWR LED is OFF, do the following:
❑ If the switch is installed on a desktop, check to be sure that the power
adapter is securely connected to a power outlet and that the power
adapter cable is securely connected to the back of the switch.
❑ If the switch is installed in an AT-MCR12 chassis, check that the unit
is fully seated in the slot.
❑ Verify that the power outlet has power by connecting another device
to it.
❑ Try using another power adapter.
If the LNK/ACT LED for the twisted pair port is OFF, do the following:
❑ Check that the end-node connected to the port is powered ON and is
operating properly.
❑ Check that the twisted pair cable is securely connected to the twisted
pair port on the switch and on the end-node.
❑ Check to be sure that the end-nodes connected to the switch are
operating at the same duplex mode.
❑ Make sure that the twisted pair cable does not exceed 100 meters (328
feet) and that you are using a Category 3 or better cable for 10Base-T
operation or a Category 5 or better cable for 100Base-TX operation.
15
Troubleshooting
If the LNK/ACT LED for the fiber optic port is OFF, do the following:
❑ Verify that the end-node connected to the port is ON and is operating
properly.
❑ Check that the fiber optic cable is securely connected to the fiber optic
port on the switch and on the end-node.
❑ Check to be sure that the end-node connected to the port is operating
at 100 Mbps.
❑ Check to be sure that the end-nodes connected to the switch are
operating at the same duplex mode.
❑ Make sure that the cable connected to the fiber optic receiver port on
the switch is connected to the transmitter port on the remote end-node
and that the fiber optic transmitter port on the switch is connected to
the receiver port on the end-node.
❑ Test the attenuation on the fiber cable to ensure that it does not
exceed acceptable values.
❑ Verify that you are using the appropriate type of fiber optic cables and
that you have not exceeded the maximum operating distance. For
cable types and operating distances, refer to Table 4 on page 10.
❑ Check that the operating specifications of the fiber optic port on the
end-node are compatible with the operating specifications of the fiber
optic port on the switch. Refer to Table 5 on page 11 for the fiber optic
port specifications.
If you are still experiencing problems after testing and troubleshooting the
installation, contact Allied Telesyn Technical Support for assistance. Refer to
“Contacting Allied Telesyn Technical Support” on page viii or visit our web
site at www.alliedtelesyn.com for support information.
16
Appendix A
Technical Specifications
Physical
Dimensions: W x D x H
10.5 cm x 9.5 cm x 2.5 cm
(4.12 in x 3.75 in x 1.0 in)
Weight: 294 g (10.4 oz)
Temperature
Maximum Operating: 0° C to 40° C (32° F to 104° F)
Maximum Storage: -25° C to 70° C (-13° F to 158° F)
Relative Humidity: 5% to 95% non-condensing
Operating Altitude: Up to 3,048 meters (10,000 feet)
Electrical Rating
Input Supply Voltage: 12 V DC ± 5%
Maximum Current: 5 mA
Power Consumption: 6 W
Agency Certifications
Safety Conforms to all standards normally supported
by Allied Telesyn products including safety
standards UL 1950, CSA 22.2 No. 950, TUV
EN60950, EN60825 CE Compliant
Standard CE Compliant IEEE 802.3, IEEE 802.3u
17
Immunity Conforms to EN55024 immunity standard
EMI/RFI Meets all applicable requirements for emissions
including but not limited to FCC Class A, IC
Class A, EN55022 Class A
Transmitter
Output Power 62.5/125 mM
-16.8 dBm
100/140 mM
50/125 mM
-20.3 dBm
85/125 mM
Fiber Optic Port Specifications
Table 7 through Table 10 lists the specifications for the fiber optic port.
Table 7 Fiber Optic Transmi tter
Model
AT-FS201 &
Fiber
Fiber
Type
1
Optic
Diameter
Optical
Frequency
(microns)
MMF 50/125 1310 nm -14.0 -20.3 -22.5
Launch Power (dBm)
Max. Avg. Min.
AT-FS202
MMF 62.5/125 1310 nm -14.0 -16.8 -19.0
AT-FS202SC/FS1 SMF 9/125 1310 nm -8.0 -11.5 -15.0
AT-FS202SC/FS2 SMF 9/125 1310 nm 0.0 -3.0 -5.0
AT-FS202SC/FS3 SMF 9/125 1310 nm 0.0 -2.0 -4.0
AT-FS202SC/FS4 SMF 9/125 1550 nm 0.0 -1.5 -3.0
1. MMF = Multimode Fiber / SMF = Si ngle-mode Fiber.
2. The launch power is m easured at one meter from the transmitte r.
18
2
AT-FS20x and AT-FS202SC/FSx Series Installation Guide
Table 8 Fiber Optic Receiver
Model
AT-FS201 &
Fiber
Fiber
Type
1
Optic
Diameter
Optical
Frequency
(microns)
MMF 50/125 1310 nm -31.8 -34.5 -14.5
Receiver Power (dBm)
Min. Avg. Saturation
AT-FS202
MMF 62.5/125 1310 nm -31.8 -34.5 -14.0
AT-FS202SC/FS1 SMF 9/125 1310 nm -31.0 -31.0 -8.0
AT-FS202SC/FS2 SMF 9/125 1310 nm -35.0 -38.0 0.0
AT-FS202SC/FS3 SMF 9/125 1310 nm -37.0 -37.0 -3.0
AT-FS202SC/FS4 SMF 9.125 1550 nm - 37.0 -37.0 -3.0
1. MMF = Multimode Fiber / SMF = Si ngle-mode Fiber.
Table 9 Fiber Optic Dat alink
Model
AT-FS201 &
AT-FS202
Fiber
1
Type
50/125
MMF
62.5/125
Minimum
Power/Link
Budget
13.00 dB 18.70 dB 0 2 km
16.80 dB 22.50 dB 0 2 km
Average
Signal
Loss (dB)
Minimum
Distance
2
Specs.
MMF
Maximum
Distance
Specs.
(1.25 mi)
(1.25 mi)
AT-FS202SC/FS1 9/125
SMF
AT-FS202SC/FS2 9/125
SMF
AT-FS202SC/FS3 9/125
SMF
AT-FS202SC/FS4 9/125
SMF
1. MMF = Multimode Fiber / SMF = Single -m ode Fi be r.
2. The recommended minimum range is stated in all cases where the maximum transmitter output
power exceeds the receivers saturation level. This is to prevent blinding or burning out of the optical
receiver on the far-end no de .
16.00 dB 19.50 dB 0 15 km
(9.4 mi)
30.00 dB 35.00 dB 0 40 km
(25 mi)
33.00 dB 35.00 dB 15 km
(9.4 mi)
34.0 35.5 dB 40 km
(24.8 mi)
75 km
(46 mi)
100 km
(62 mi)
19
Table 10 Fiber Optic Loss Specification (Benchmark)
Fiber Optic
Fiber Type
1
Diameter
MMF 50/125
Optical
Frequency
Typical Loss
Factor
Worst Case
Loss Factor
Bandwidth
1310 nm 1.00 dB/km 1.50 dB/km 400 Mhz-km
microns
62.5/125
1310 nm 1.00 dB/km 1.50 dB/km 500 Mhz-km
microns
SMF 9/125
microns
1310 nm 0.40 dB/km 1.00 dB/km Not
applicable
SMF 9 /125 1550 nm 0.30 dB/km 0.75 dB/km Not
applicable
1. MMF = Multimode Fiber / SMF = Si ngle-mode Fiber.
Pinout Assignments
Figure 1 shows the pin assignments of the RJ-45 connector.
Pin 1 Pin 8
Figure 1 RJ-45 Pin Assignments
Table 5 lists the 10/100Base-TX connector pins and their signals when the port
is operating in either MDI or MDI-X configuration.
Table 11 RJ-45 Pinouts
MDI-X (Defaul t) Signal MDI Signal
1 RX+ 1 TX+
2 RX- 2 TX3TX+3 RX+
4- 4 5- 5 6TX-6 RX7- 7 8- 8 -
20
Appendix B
Electrical Safety and Installation Requirements
Important: This appendix contains multiple-language translations for the
safety statements in this guide.
Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch
enthaltenen Sicherheitshinweise in mehreren Sprachen.
Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af
sikkerhedsadvarslerne i denne håndbog.
Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de
veiligheidsopmerkingen in deze gids.
Important: Cette annexe contient la traduction en plusieurs langues des
instructions de sécurité figurant dans ce guide.
Tärkeää: Tämä liite sisältää tässä oppaassa esiintyvät turvaohjeet usealla
kielellä.
Importante: questa appendice contiene traduzioni in più lingue degli avvisi
di sicurezza di questa guida.
Viktig: Dette tillegget inneholder oversettelser til flere språk av
sikkerhetsinformasjonen i denne veiledningen.
Importante: Este anexo contém traduções em vários idiomas das
advertências de segurança neste guia.
Importante: Este apéndice contiene traducciones en múltiples idiomas de los
mensajes de seguridad incluidos en esta guía.
Obs! Denna bilaga innehåller flerspråkiga översättningar av
säkerhetsmeddelandena i denna handledning.
21
Standards: This product meets the following standards.
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with this instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or
the FCC, can void your right to operate this equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement
sur le matériel brouilleur du Canada.
$ 1 RFI Emission EN55022 Class A
$ 2 Warning: In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
$ 3 Immunity EN55024
$ 4 Warning: This product requires shielded cables to comply with emission and
immunity standards. If it is used with unshielded cables, the user may be required
to take measures to correct the interference problem at their own expense.
$ 5 Electrical Safety EN60950, UL1950, CSA 950
$ 6Laser EN60825
$ 7 Warning Class 1 Laser product.
$ 8 Warning Do not stare into the Laser beam.
At time of installation, the Fiber Optic Lasers comply with FDA Radiation
Performance Standard 21CFR Subchapter J, applicable at date of manufacture.
$ 9 This is a “CLASS 1 LED PRODUCT” (AT-FS201, AT-FS202, AT-FS203 models)
Safety
$ 10 Lightning Danger
Danger: DO NOT WORK on equipment or CABLES during periods of LIGHTNING
ACTIVITY.
$ 11 DO NOT BLOCK AIR VENTS
$ 12 Power to the hub must be sourced only from the adapter.
USA/Canada
Use a UL Listed/CSA Certified AC adapter of DC 12V, 500mA.
Europe - EU
Use TÜV licensed AC adapter of DC 12V, 500mA.
UK
Use a UK Safety Approved AC adapter of DC 12V, minimum 500mA.
$ 13 Operating Temperature
This product is designed for a maximum ambient temperature of 40 degrees C.
$ 14 All Countries: Install product in accordance with local and National Electrical
Codes.
22
AT-FS20x and AT-FS202SC/FSx Series Installation Guide
Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.
$ 1Hochfrequenzstörung EN55022 Klasse A
$ 2 Warnung: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen
hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen
ergreifen.
$ 3Störsicherheit EN55024
$ 4 Achtung: Für dieses Produkt sind abgeschirmte Kabel erforderlich, damit den
Richtlinien für Emission und Interferenzschutz entsprochen wird. Falls das Produkt
mit nicht abgeschirmten Kabeln verwendet wird, können weitergehende
Maßnahmen für die Korrektur von Interferenzproblemen auf Kosten des Benutzers
notwendig werden.
$ 5 Elektrische Sicherheit EN60950, UL1950, CSA 950
$ 6Laser EN60825
$ 7 Warnung Laserprodukt der Klasse 1.
$ 8 Warnung Nicht direkt in den Strahl blicken.
$ 9 Das ist ein “LED Produkt der Klasse 1”
Sicherheit
$ 10 Gefahr Durch Blitzschlag
Gefahr: Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters
ausführen
$ 11 ENTLÜFTUNGSÖFFNUNGEN NICHT VERSPERREN
$ 12 Der Buchse darf nur aus dem Adapter Strom zugeführt werden.
Europe - EU
Gebrauchen Sie einen von TÜV zugelassenen Wechselstromadapter für Gleichstrom
12 V, 500 mA.
$ 13 Betriebstemperatur
Dieses Produkt wurde für den Betrieb in einer Umgebungstemperatur von nicht
mehr als 40° C entworfen.
$ 14 Alle Länder: Installation muß örtlichen und nationalen elektrischen Vorschriften
entsprechen.
Standarder: Dette produkt tilfredsstiller de følgende standarder.
$ 1 Radiofrekvens
forstyrrelsesemission EN55022 Klasse A
$ 2 Advarsel: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse.
Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige
foranstaltninger.
$ 3 Immunitet EN55024
$ 4 Advarsel: Dette produkt skal bruges med afskærmede kabler for at overholde
bestemmelserne vedrørende udstråling og støjimmunitet. Hvis det bruges med
uafskærmede kabler, kan det blive påkrævet af brugeren at korrigere
interferensproblemer for egen regning.
$ 5 Elektrisk sikkerhed. EN60950, UL1950, CSA 950
$ 6Laser EN60825
$ 7 Advarsel Laserprodukt av klasse 1.
$ 8Advarsel Stirr ikke på strålen.
$ 9 Dette er et “PRODUKT UNDER KLASSE 1 LED”
23
Sikkerhed
$ 10 Fare Under Uvejr
Fare: UNDLAD at arbejde på udstyr eller KABLER i perioder med
LYNAKTIVITET.
$ 11 VENTILATIONSÅBNINGERNE MÅ IKKE BLOKERES
$ 12 Strømforsyningen til apparatet må udelukkende tages fra
tilpasningstransformatoren.
Europe - EU
Brug kun TÜV godkendt vekselstrømstransformator på 12 V jævnstrøm, 500 mA.
$ 13 Betjeningstemperatur
Dette apparat er konstrueret til en omgivende temperatur på maksimum 40 grader
C.
$ 14 Alle Lande: Installation af produktet skal ske i overensstemmelse med lokal og
national lovgivning for elektriske installationer.
Eisen: Dit product voldoet aan de volgende eisen.
$ 1 RFI Emissie EN55022 Klasse A
$ 2 Waarschuwing: Binnenshuis kan dit product radiostoring veroorzaken, in welk
geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen.
$ 3 Immuniteit EN55024
$ 4 Waarschuwing: Om te voldoen aan de emissie- en immuniteitsnormen dient dit
apparaat te zijn voorzien van afgeschermde kabels. Als het met niet-afgeschermde
kabels wordt gebruikt, kan het zijn dat de gebruiker maatregelen moet treffen om
interferentieproblemen voor eigen rekening op te lossen.
$ 5 Electrische Veiligheid EN60950, UL1950, CSA 950
$ 6Laser EN60825
$ 7 Waarshuwing Klasse-1 laser produkt.
$ 8 Waarchuwing Neit in de straal staren.
$ 9 Dit is een “KLASSE 1 LED-PRODUKT”
Veiligheid
$ 10 Gevaar Voor Blikseminslag
Gevaar: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.
$ 11 VENTILATIEGATEN NIET BLOKKEREN
$ 12 Stroom mag alleen via de adapter naar het apparaat toegevoerd worden.
Europe - EU
Gebruik een door TÜV gekeurde wisselstroomadapter van 12 Volt gelijkstroom, 500
milliampères.
$ 13 Bedrijfstemperatuur
De omgevingstemperatuur voor dit produkt mag niet meer bedragen dan 40 graden
Celsius.
$ 14 Alle Landen: het toestel installeren overeenkomstig de lokale en nationale
elektrische voorschriften.
24
AT-FS20x and AT-FS202SC/FSx Series Installation Guide
Normes: ce produit est conforme aux normes de suivantes.
$ 1 Emission d'interférences
radioélectriques EN55022 Classe
$ 2Mise En Garde: dans un environnement domestique, ce produit peut provoquer des
interférences radioélectriques. Auquel cas, l'utilisateur devra prendre les mesures
adéquates.
A
$ 3 Immunité EN55024
$ 4 Avertissement : Il faut utiliser des câbles blindés pour ce produit afin de respecter
les normes d’émission et d’immunité. Si l’utilisateur choisit d’utiliser des câbles non
blindés, il sera peut-être contraint de prendre les mesures nécessaires pour corriger
les problèmes d’interférences, ainsi que d’assumer le coût correspondant.
$ 5Sécurité électrique EN60950, UL1950, CSA 950
$ 6Laser EN60825
$ 7 Attention Producit laser di classe 1.
$ 8 Attention Ne pas fixer le faisceau des yeux.
$ 9 Ce mat‚riel est un “PRODUIT A DIODE LECTROLUMINESCENTE DE CLASSE 1”
Sécurité
$ 10 Danger De Foudre
Danger: NE PAS MANIER le matériel ou les CÂBLES lors d'activité orageuse.
$ 11 NE PAS BLOQUER LES FENTES D'AÉRATION
$ 12 L'alimentation du concentrateur doit être uniquement fournie par l'adaptateur.
Europe - EU
Utiliser un adaptateur secteur conforme TÜV de 12 V, 500 mA en courant continu.
$ 13 Température De Fonctionnement
Ce matériel est capable de tolérer une température ambiante maximum de 40 degrés
Celsius.
$ 14 Pour Tous Pays: Installer le matériel conformément aux normes électriques
nationales et locales.
Standardit: Tämä tuote on seuraavien standardien mukainen.
$ 1 Radioaaltojen häirintä EN55022 Luokka A
$ 2Varoitus: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä
tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin
toimenpiteisiin.
$ 3Kestävyys EN55024
$ 4Varoitus: Tämä tuote vaatii suojattuja kaapeleita toimiakseen emissio- ja
häiriönsietostandardien mukaisesti. Jos tuotetta käytetään ilman suojattuja
kaapeleita, käyttäjä voi joutua korjaamaan häirinnän aiheuttaman ongelman
omalla kustannuksellaan.
$ 5Sähköturvallisuus EN60950, UL1950, CSA 950
$ 6Laser EN60825
$ 7Varoitus Luokan 1 Lasertuote.
$ 8Variotus Älä katso säteeseen.
$ 9 Tämä on “ENSIMMÄISEN LUOKAN VALODIODITUOTE”
Turvallisuus
$ 10 Salamaniskuvaara
Engenvaara: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA
SALAMOINNIN AIKANA.
$ 11 ÄLÄ TUKI ILMAREIKIÄ
25
$ 12 Tähtipisteeseen (hub) syötettävän virran pitää tulla ainoastaan sovittimesta.
Europe - EU
Käytä TÜV-lisenssillä valmistettua verkkosovitinta, jonka tasajännitteen
nimellisarvot ovat DC 12 V, 500 mA (milliampeeria).
$ 13 Käyttölämpötila
Tämä tuote on suunniteltu ympäröivän ilman maksimilämpötilalle 40° C.
$ 14 Kaikki Maat: Asenna tuote paikallisten ja kansallisten
$ 1 Emissione RFI (interferenza di
sähköturvallisuusmääräysten mukaisesti.
Standard: Questo prodotto è conforme ai seguenti standard.
radiofrequenza) EN55022 Classe
A
$ 2Avvertenza: in ambiente domestico questo prodotto potrebbe causare radio
interferenza. In questo caso potrebbe richiedersi all'utente di prendere gli adeguati
provvedimenti.
$ 3 Immunità EN55024
$ 4Avvertenza: questo prodotto, se utilizzato con cavi schermati, è conforme alle
norme sulle emissioni e sull’immunità. In caso di uso senza cavi schermati, l’utente
può dover adottare a proprie spese misure correttive contro le interferenze.
$ 5 Sicurezza elettrica EN60950, UL1950, CSA 950
$ 6Laser EN60825
$ 7Avvertenza Prodotto laser di Classe 1.
$ 8Avertenza Non fissare il raggio con gli occhi.
$ 9 Questo è un “PRODOTTO CON LED DI CLASSE 1”
NORME DI SICUREZZA
$ 10 Pericolo Di Fulmini
Pericolo: NON LAVORARE sul dispositivo o sui CAVI durante PRECIPITAZIONI
TEMPORALESCHE.
$ 11 NON OSTRUIRE LE PRESE D'ARIA
$ 12 Questo dispositivo deve essere alimentato solo mediante l’adattatore.
Europe - EU
Utilizzare l’adattatore per c.a. da 12 V c.c. e 500 mA conforme alla normativa TÜV.
$ 13 Temperatura Di Funzionamento
Questo prodotto è concepito per una temperatura ambientale massima di 40 gradi
centigradi.
$ 14 Tutti I Paesi: installare il prodotto in conformità delle vigenti normative elettriche
nazionali.
26
AT-FS20x and AT-FS202SC/FSx Series Installation Guide
Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer.
$ 1 RFI stråling EN55022 Klasse A
$ 2 Advarsel: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake
radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler.
$ 3 Immunitet EN55024
$ 4 Advarsel: Dette produktet må brukes med vernede kabler for å tilfredsstille
emisjons- og fritakelsesstandarder. Dersom produktet brukes med uvernede kabler,
må brukeren muligens rette forstyrrelsesproblemene for egen regning.
$ 5 Elektrisk sikkerhet EN60950, UL1950, CSA 950
$ 6Laser EN60825
$ 7 Advarsel Laserprodukt av klasse 1.
$ 8 Advarsal Stirr ikke på strålen.
$ 9 Dette er et “KLASSE 1 LED PRODUKT”
Sikkerhet
$ 10 Fare For Lynnedslag
Fare: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.
$ 11 BLOKKER IKKE LUFTVENTILENE
$ 12 All strømtilførsel må komme fra adapteren.
Europe - EU
Benytt TÜV-godkjent AC-adapter på 12V DC, 500mA (millismpere)
$ 13 Driftstemperatur
Dette produktet er konstruert for bruk i maksimum romtemperatur på 40 grader
celsius.
$ 14 Alle Land: Produktet må installeres i samsvar med de lokale og nasjonale
elektriske koder.
Padrões: Este produto atende aos seguintes padrões.
$ 1Emissão De Interferência De
Radiofrequência EN55022 Classe
A
$ 2Aviso: Num ambiente doméstico este produto pode causar interferência na
radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas
adequadas.
$ 3 Imunidade EN55024
$ 4Advertência: Este produto requer a utilização de cabos blindados para
cumprimento dos standards de limites de emissão e imunidade. Se o produto for
utilizado com cabos não blindados, o utilizador poderá necessitar de tomar medidas
para correcção de problemas de interferência, por sua própria conta.
$ 5Segurança Eléctrica TUV-EN60950, UL1950, CSA 950
$ 6Laser EN60825
$ 7Aviso Produto laser de classe 1.
$ 8Aviso Não olhe fixamente para o raio.
$ 9 Este é um “PRODUTO CLASSE 1 LED”
Segurança
$ 10 Perigo De Choque Causado Por Raio
Perigo: NÃO TRABALHE no equipamento ou nos CABOS durante períodos
suscetíveis a QUEDAS DE RAIO.
$ 11 NÃO BLOQUEIE AS ABERTURAS DE VENTILAÇÃO
$ 12 Use somente o adaptador fornecido para alimentação elétrica do hub.
27
Europe - EU
Use um adaptador de corrente alternada com saída DC de 12V e 500mA em
conformidade com as especificações da TÜV.
$ 13 Temperatura De Funcionamento
Este produto foi projetado para uma temperatura ambiente máxima de 40 graus
centígrados.
$ 14 Todos Os Países: Instale o produto de acordo com as normas nacionais e locais para
instalações elétricas.
Estándares: Este producto cumple con los siguientes estándares.
$ 1Emisión RFI EN55022 Clase A
$ 2Advertencia: en un entorno doméstico, este producto puede causar
radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas
que sean convenientes al respecto.
$ 3 Inmunidad EN55024
$ 4Advertencia: Este producto exige cables protectores para ajustarse a las normas de
emisión e inmunidad. Si se utiliza con cables sin protección, el usuario tendrá que
correr con los gastos por las medidas a tomar en caso de problemas de interferencias.
$ 5Seguridad eléctrica TUV-EN60950, UL1950, CSA 950
$ 6Laser EN60825
$ 7 ¡Advertencia! Producto láser Clase 1.
$ 8 ¡Advertencia! No mirat fijamente el haz.
$ 9 Este es un “PRODUCTO DE DIODO LUMINISCENTE (LED) CLASE 1”
Seguridad
$ 10 Peligro De Rayos
Eligro: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los equipos
o en LOS CABLES durante TORMENTAS ELECTRICAS.
$ 11 NO BLOQUEE LAS ABERTURAS PARA VENTILACION
$ 12 La energía para el dispositivo central o "hub" debe provenir únicamente del
adaptador.
Europe - EU
Utilizar un adaptador de corriente alterna autorizado TÜV de 12 voltios de corriente
continua y 500 miliamperios.
$ 13 Temperatura Requerida Para La Operación
Este producto está diseñado para una temperatura ambiental máxima de 40 grados
C.
$ 14 Para Todos Los Países: Monte el producto de acuerdo con los Códigos Eléctricos
locales y nacionales.
28
AT-FS20x and AT-FS202SC/FSx Series Installation Guide
Standarder: Denna produkt uppfyller följande standarder.
$ 1Radiostörning EN55022 Klass A
$ 2 Varning: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan
tvinga användaren till att vidtaga erforderliga åtgärder.
$ 3 Immunitet EN55024
$ 4 Varning! Denna produkt kräver skärmade kablar för att uppfylla standardkraven
för emission och immunitet. Om den används med oskärmade kablar kan
användaren vara tvungen att vidta åtgärder på egen bekostnad för att åtgärda
störningsproblemet.
$ 5Elsäkerhet TUV-EN60950, UL1950, CSA 950
$ 6Laser EN60825
$ 7 Varning! Laserprodukt av klass 1.
$ 8 Varning! Laserstrålning när enheten är öppen.
$ 9 Detta är en “KLASS 1 LYSDIODPRODUKT”
Säkerhet
$ 10 Fara För Blixtnedslag
Fara: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER.
$ 11 BLOCKERA INTE LUFTVENTILERNA
$ 12 Endast anslutningsenheten får vara kraftkälla till centralen.
Europe - EU
Använd en växelströmsanslutningsenhet licensierad av TÜV. Likström 12V, 500mA.
$ 13 Driftstemperatur
Denna produkt är konstruerad för rumstemperatur ej överstigande 40 grader
Celsius.
$ 14 Alla Länder: Installera produkten i enlighet med lokala och statliga bestämmelser
för elektrisk utrustning.
29
Appendix C
Technical Support Fax Order
Name _________________________________________________________________
Company______________________________________________________________
Address _______________________________________________________________
City______________________ State/Province_______________________________
Zip/Postal Code ________________ Country_______________________________
Phone______________________________ Fax _______________________________
Incident Summary
Model number of Allied Telesyn product I am using________________________
Firmware release number of Allied Telesyn product _______________________
Other network software products I am using (e.g., network managers)
______________________________________________________________________
______________________________________________________________________
Brief summary of problem ______________________________________________
______________________________________________________________________
______________________________________________________________________
Conditions (List the steps that led up to the problem.)______________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
Detailed description (Please use separate sheet)
Please also fax printouts of relevant files such as batch files and configuration
files. When completed, fax this sheet to the appropriate Allied Telesyn office.
Fax numbers can be found on page viii.
31
Loading...