Allen&Heath iDR0 User Manual

ALLEN&HEATH

iDR0

iLive Mix System DSP MiniRack

USER GUIDE

Publication AP7129

Limited Two Year Warranty

This product has been manufactured in the UK by ALLEN & HEATH and
is warranted to be free from defects in materials or workmanship for a
period of two years from the date of purchase by the original owner.

To ensure a high level of performance and reliability for which this
equipment has been designed and manufactured, read this User Guide
before operating.

In the event of a failure, notify and return the defective unit to ALLEN &
HEATH or its authorised agent as soon as possible for repair under
warranty subject to the following conditions:

Conditions Of Warranty

1. The equipment has been installed and operated in accordance with
the instructions in this User Guide

2. The equipment has not been subject to misuse either intended or
accidental, neglect, or alteration other than as described in the User
Guide or Service Manual, or approved by ALLEN & HEATH.

3. Any necessary adjustment, alteration or repair has been carried out
by ALLEN & HEATH or its authorised agent.

4. The defective unit is to be returned carriage prepaid to ALLEN &
HEATH or its authorised agent with proof of purchase.

5. Units returned should be packed to avoid transit damage.

In certain territories the terms may vary. Check with your ALLEN &
HEATH agent for any additional warranty, which may apply.

This product complies with the European Electromagnetic
Compatibility directives 89/336/EEC & 92/31/EEC and the
European Low Voltage Directives 73/23/EEC & 93/68/EEC.

Any changes or modifications to the power supply unit not approved
by Allen & Heath could void the compliance of the product and
therefore the users authority to operate it.

iDR0 User Guide AP7129 Issue 1.

Copyright © 2008 Allen & Heath. All rights reserved

Manufactured in the United Kingdom by Allen & Heath Limited

Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK

http://www.allen-heath.com

2 iDR0 User Guide

Important Safety Instructions

WARNINGS - Read the following before proceeding :

CAUTION

ATTENTION: RISQUE DE CHOC ELECTRIQUE – NE PAS OUVRIR

Read instructions: Retain these safety and operating instructions for future reference. Adhere to

all warnings printed here and on the equipment. Follow the operating
instructions printed in this User Guide.

Do not remove covers: Operate the equipment with its covers correctly fitted. Refer any service work

on the equipment to competent technical personnel only.

Power sources: Connect the equipment to a mains power supply only of the type described

in this User Guide and marked on the rear panel. Use only the power cord
with sealed mains plug appropriate for your local mains supply as provided
with the equipment. If the provided plug does not fit into your outlet consult
your service agent for assistance.

Power cord routing: Route the power cord so that it is not likely to be walked on, stretched or

pinched by items placed upon or against it.

Grounding: Do not defeat the grounding and polarisation means of the power cord plug.

Do not remove or tamper with the ground connection in the power cord.

WARNING: This equipment must be earthed.

Water and moisture: To reduce the risk of fire or electric shock do not expose the equipment to

rain or moisture or use it in damp or wet conditions. Do not place containers
of liquid on it which might spill into any openings.

Ventilation: Do not obstruct the ventilation slots or position the equipment where the air

flow required for ventilation is impeded. If the equipment is to be operated in
a flightcase ensure that it is constructed to allow adequate ventilation.

Heat and vibration: Do not locate the equipment in a place subject to excessive heat or direct

sunlight as this could be a fire hazard. Locate the equipment away from any
devices which produce heat or cause excessive vibration.

Servicing: Switch off the equipment and unplug the power cord immediately if it is

exposed to moisture, spilled liquid, objects fallen into the openings, the
power cord or plug become damaged, during lightening storms, or if smoke,
odour or noise is noticed. Refer servicing to qualified technical personnel
only.

Installation: Install the equipment in accordance with the instructions printed in this User

Guide. Use the equipment connections for their intended purpose only.

iDR0 User Guide 3

Important Mains plug wiring instructions.

The unit is supplied with a moulded mains plug fitted to the AC mains
power lead. Follow the instructions below if the mains plug has to be
replaced.

The wires in the mains lead are coloured in accordance with the
following code:

L LIVE BROWN BLACK

N NEUTRAL BLUE WHITE

E EARTH GND GREEN & YELLOW GREEN

The wire which is coloured Green and Yellow must be connected to
the terminal in the plug which is marked with the letter E or with the
Earth symbol. This appliance must be earthed.

The wire which is coloured Blue must be connected to the terminal in
the plug which is marked with the letter N.

The wire which is coloured Brown must be connected to the terminal
in the plug which is marked with the letter L.

Ensure that these colour codes are followed carefully in the event of
the plug being changed.

Precautions

TERMINAL

WIRE COLOUR

European USA/Canada

Damage : To prevent damage to the equipment cosmetics, avoid placing heavy

objects on the unit, scratching the surface with sharp objects,
subjecting the unit to rough handling and vibration.

Environment : Protect from excessive dirt, dust, heat and vibration when operating

and storing. Avoid tobacco ash, smoke, drinks spillage, and
exposure to rain and moisture. If the equipment becomes wet, switch
off and remove power immediately. Allow to dry out thoroughly
before using again.

Cleaning : Avoid the use of chemicals, abrasives or solvents. The equipment is

best cleaned with a soft brush and dry lint-free cloth. If the ventilation
grilles become blocked with dust use a vacuum cleaner to suck the
dirt out. Do not remove the cover to clean the unit.

Transporting : The equipment should be transported in the original packing or

purpose built flightcase to protect it from damage during transit.

or

Cables: Plan the location of the equipment so that the connecting cables are

not fully extended. Full extension of the cables can stress the
equipment and cables and may result in undesired performance.
Ensure that the cables are located such that they cannot be stood on
or tripped over.

Modules: Do not remove the modules from the unit while power is applied.

4 iDR0 User Guide

Introduction

This is the user guide for the Allen & Heath iDR0 ‘MiniRack’ mix engine. We recommend
that you read this fully before starting. Included is information on installing, connecting
and operating the unit along with panel drawings, application drawings and technical
specification. Whilst we believe the information in this guide to be reliable we do not
assume responsibility for inaccuracies. We also reserve the right to make changes in the
interest of further product development.

We are able to offer further product support through our worldwide network of approved
dealers and service agents. You can also access our Web site (www.allen-heath.com)
for information on our company and its pedigree, our full product range and our design
philosophy. To help us provide the most efficient service please keep a record of your
unit serial number, and date and place of purchase to be quoted in any communication
regarding this product. The serial number is located on the rear panel.

The iDR0 is one of many components that can connect together to create an iLive
mixing system. For further information on configuring and using iLive please refer to:

iLive System Reference guide AP6526

iDR0 Getting Started Guide AP7284

iLive Getting Started Guide AP7260

Allen & Heath Resource CD AP4742

Allen & Heath web site www.allen-heath.com

Firmware Release Notes Downloadable from web site

Help file within system firmware

Check the packing contents

Retain the product packing should you need to ship the product in future. You should find the
following components:

1x iDR0 MiniRack. This is packed with its rubber feet
fitted. The feet can be removed for rack mounting.

1x IEC MAINS LEAD with moulded plug. Check that the
plug is suitable for connection to your local mains
supply.

iDR0/n
Where n = mains voltage 120 (USA), 220 (EU), 240 (UK)

1x CAT5 CABLE 1.8m RJ45 Ethercon connections.

Part number AH7001. Connects the iDR0 to the iLive
Surface or another MixRack. Note that the second cable
required is shipped with the iLive Surface.

DOCUMENTATION including the User Guide AP7129,
Getting Started Guide AP7284, Safety Sheet AP3345,
Registration Card AP3594, and sticker AP4943.

iDR0 User Guide 5