How it Works
ALFA Network
Loading...
AIP-W512
User Manual
66 pgs1.43 Mb0

ALFA Network AIP-W512 User Manual

AIP-W512
Rev: 1.0.0
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
National restrictions
This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country Restriction Reason/remark
Bulgaria None
Outdoor use limited to 10
France
Italy None
Luxembourg None
Norway Implemented
Russian Federation None Only for indoor applications
mW e.i.r.p. within the band
2454-2483.5 MHz
General authorization required for outdoor use and
public service
Military Radiolocation use. Refarming of the 2.4 GHz
band has been ongoing in recent years to allow current
relaxed regulation. Full implementation planned 2012
If used outside of own premises, general authorization is
required
General authorization required for network and service
supply(not for spectrum)
This subsection does not apply for the geographical area
within a radius of 20 km from the centre of Ny-Ålesund
Note: Please don’t use the product outdoors in France.
CONTENTS
Package Contents .................................................................................................................................1
Chapter 1.Introduction .......................................................................................................................2
1.1Overview .............................................................................................................................2
1.2Main Features .....................................................................................................................3
1.3Panel Layout .......................................................................................................................4
1.3.1The Front Panel ......................................................................................................4
1.3.2The Rear Panel ......................................................................................................4
Chapter 2.Connecting the Router .....................................................................................................6
2.1System Requirements .........................................................................................................6
2.2Installation Environment Requirements ..............................................................................6
2.3Connecting the Router ........................................................................................................6
Chapter 3.Quick Installation Guide ...................................................................................................8
3.1TCP/IP Configuration ..........................................................................................................8
3.2Quick Installation Guide ....................................................................................................10
Chapter 4.Configuring the Router ..................................................................................................16
4.1Login .................................................................................................................................16
4.2Status ................................................................................................................................16
4.3Quick Setup .......................................................................................................................17
4.4WPS ..................................................................................................................................17
4.5TCP/IP Settings .................................................................................................................20
4.5.1LAN .......................................................................................................................20
4.5.2WAN Interface ......................................................................................................22
4.6Wireless ............................................................................................................................30
4.6.1Basic Settings .......................................................................................................30
4.6.2Advanced Settings ................................................................................................32
4.6.3Security .................................................................................................................33
4.6.4Access Control .....................................................................................................37
4.6.5WDS Settings .......................................................................................................38
4.6.6Site Survey ...........................................................................................................40
4.6.7WPS ......................................................................................................................41
4.6.8Schedule ...............................................................................................................41
- I -
4.7Firewall ..............................................................................................................................42
4.7.1Port Filtering .........................................................................................................42
4.7.2IP Filtering .............................................................................................................43
4.7.3MAC Filtering ........................................................................................................43
4.7.4Port Forwarding ....................................................................................................44
4.7.5URL Filtering .........................................................................................................45
4.7.6DMZ ......................................................................................................................45
4.7.7VLAN ....................................................................................................................46
4.8QoS ...................................................................................................................................47
4.9Management .....................................................................................................................47
4.9.1Status ....................................................................................................................48
4.9.2Statistics ...............................................................................................................48
4.9.3DDNS ....................................................................................................................49
4.9.4Time Zone Setting ................................................................................................50
4.9.5Denial-of-Service ..................................................................................................50
4.9.6Log ........................................................................................................................51
4.9.7Upgrade Firmware ................................................................................................52
4.9.8Save/Reload Setting .............................................................................................53
4.9.9Password ..............................................................................................................54
Appendix A: FAQ .................................................................................................................................55
Appendix B: Configuring the PC .......................................................................................................56
Appendix C: Specifications ................................................................................................................59
Appendix D: Glossary .........................................................................................................................60
- II -
AIP-W512
Package Contents
The following items should be found in your package:
AIP-W512
USB Cable
Quick Installation Guide
Note:
Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact your distributor.
- 1 -
AIP-W512
Chapter 1. Introduction
Thank you for choosing the AIP-W512.
1.1 Overview
The AIP-W512 delivers exceptional range and speed, which can fully meet the need of Small Office/Home Office (SOHO) networks and users that demand higher networking performance.
The AIP-W512 provides up to 150M wireless connection with other 802.11n wireless clients. The speed makes it ideal for handling multiple data streams at the same time ensuring your network stability. It is compatible with all IEEE 802.11g and IEEE 802.11b products.
Multiple Security Protections
The multiple protection measures include SSID broadcast control and wireless LAN 64/128-bit WEP encryption, Wi-Fi protected Access (WPA2- PSK, WPA- PSK), as well as advanced Firewall protections. The AIP-W512 provides complete data privacy.
AIP-W512 Router provides flexible access control for parents and network administrators to establish restricted access policies for children or staff members. The network administrators can manage and monitor the network in real time with the remote management function.
Incredible Speed
t
Flexible Access Control
Simple Installation
Since the Router is compatible with virtually all the major operating systems, it is easy to manage and operate. The Quick Setup Wizard is supported and detailed step by step instructions are in this user guide. Before installing the Router, please look through the user guide to know all the Router’s functions.
- 2 -
AIP-W512
1.2 Main Features
IEEE 802.11n wireless technology to provide a wireless data rate of up to 150Mbps.
One 10/100M Auto-Negotiation RJ45 WAN port, four 10/100M Auto-Negotiation RJ45 LAN
ports, supporting Auto MDI/MDIX.
Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security.
Shares data and Internet access for users, supporting Dynamic IP/Static IP/PPPoE Internet
access.
Supports Virtual Server, Special Application and DMZ host.
Supports UPnP, Dynamic DNS, Static Routing.
Provides Automatic-connection and Scheduled Connection to the Internet on specified times.
Connects Internet on demand and disconnects from the Internet when idle for PPPoE.
Built-in NAT and DHCP server supporting static IP address distribution.
Supports Stateful Packet Inspection.
Supports VPN Passthrough.
Provides 64/128-bit WEP encryption security and wireless LAN ACL (Access Control List).
Supports Flow Statistics.
Supports firmware upgrade and Web management.
- 3 -
1.3 Panel Layout
1.3.1 The Front Panel
The Router’s LEDs and the WPS Button are located on the side panel.
Name Status Indication
PWR
WLAN
LAN,
WAN,
Off On Power is on. Off The Wireless function is disabled or not active
Flashing The Wireless active
Off There is no device linked to the corresponding port.
On
Flashing There is an active device linked to the corresponding port.
Off There is no device linked to the corresponding port.
On
Flashing There is an active device linked to the corresponding port.
Power is off.
There is a device linked to the corresponding port but there is no activity.
There is a device linked to the corresponding port but there is no activity.
AIP-W512
1.3.2 The Side Panel
Table 1-1 The LEDs Description
Figure 1-2 Rear Panel sketch
- 4 -
AIP-W512
The following parts are located on the rear panel (View from left to right).
POWER: The Power socket is where you will connect the power adapter. Please use the
power adapter provided with the AIP-W512.
WAN : The WAN port is where you will connect the DSL/cable Modem, or Ethernet.
LAN: One LAN 10/100Mbps RJ45 port connects to a network device, such as a switch or a
router.
WPS: To receive and transmit the wireless data.
- 5 -
AIP-W512
Chapter 2. Connecting the Router
2.1 System Requirements
Broadband Internet Access Service (DSL/Cable/Ethernet)
One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is
connected directly to the Ethernet.)
PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors
TCP/IP protocol on each PC
Web browser, such as Microsoft Internet Explorer.
2.2 Installation Environment Requirements
Place the Router in a well-ventilated place away from any heater or heating vent
Avoid direct irradiation of any strong light (such as sunlight)
Keep at least 2 inches (5 cm) of clear space around the Router
Operating Temperature: -20 ~℃ 60 ℃
Operating Humidity: 10%~90%RH, Non-condensing
2.3 Connecting the Router
Before installing the Router, make sure your PC is connected to the Internet through the broadband service successfully. If there is any problem, please contact your ISP. Install the Router according to the following steps. Don't forget to pull out the power plug and keep your hands dry.
1. Turn the power off for your PC, Cable/DSL Modem, and the Router.
2. Locate an optimum location for the Router. The best place is usually at the center of your wireless network environment.
3. Adjust the direction of the antenna. Normally, upright is a good direction.
4. Connect the PC(s) and each Switch/Hub in your LAN to the LAN Ports on the Router, shown in Figure 2-1. (If you have the wireless NIC and want to use the wireless function, you can skip this step.)
5. Connect the DSL/Cable Modem to the WAN port on the Router, shown in Figure 2-1.
6. Connect the power adapter to the power socket on the Router, and the other end into an electrical outlet. Press the power switch, and then the router will start to work.
- 6 -
7. Turn the power on for your PC and Cable/DSL Modem.
AIP-W512
Figure 2-1 Hardware Installation of the AIP-W512
- 7 -
AIP-W512
Chapter 3. Quick Installation Guide
This chapter will show you how to configure the basic functions of your AIP-W512 using Quick Setup Wizard within minutes.
3.1 TCP/IP Configuration
The default IP address for AIP-W512 is 192.168.2.1. And the default Subnet Mask is
255.255.255.0. These values can be changed to your preference.
Connect the local PC to the LAN ports of the AIP-W512. You can configure the IP address for your PC with the following options.
Configure the IP address manually
1) Set up the TCP/IP Protocol for your PC. If you need instructions as to how to do this,
please refer to Appendix B: Configuring the PC
2) Configure the network parameters. The IP address is 192.168.2.xxx ("xxx" represents
any number from 2 to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.2.1 (The Router's default IP address).
Obtain an IP address automatically
1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC.
If you need instructions as to how to do this, please refer to Appendix B: Configuring the
PC.
2) The built-in DHCP server will assign an IP address for the PC.
Now, you can run the Ping command in the command prompt to verify the network connection between your PC and the Router. The following example is in Windows XP OS.
Open a command prompt, and type ping 192.168.2.1, and then press Enter.
If the result displayed is similar to the Figure 3-1, it means the connection between your PC
and the Router has been established well.
.
- 8 -
AIP-W512
Figure 3-1 Success result of Ping command
If the result displayed is similar to the Figure 3-2, it means the connection between your PC
and the Router has failed.
Figure 3-2 Failure result of Ping command
To check the connection follow these steps:
1. Is the connection between your PC and the Router correct?
Note:
The 1/2/3/4 LEDs of LAN ports which you link to on the Router and LEDs on your PC's adapter should be lit.
2. Is the TCP/IP configuration for your PC correct?
The Router's IP address is 192.168.2.1. Your PC's IP address must be within the range of
192.168.2.2 ~ 192.168.2.254.
Note:
- 9 -
AIP-W512
3.2 Quick Installation Guide
With a Web-based utility, it is easy to configure and manage AIP-W512. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
1. To access the configuration utility, open a web-browser and type in the default address
http://192.168.2.1
in the address field of the browser.
Figure 3-3 Log in the Router
A login window may pop up; leave the User Name and Password blank. Then click OK or press Enter.
2. After successfully logging in, click the Quick Setup menu to quickly configure your Router.
Figure 3-4 Quick Setup
- 10 -
AIP-W512
3. Click Next, and then Operation Mode page will appear, shown in Figure 3-5.
Figure 3-5 Quick Setup - WAN Connection Type
The Router provides three popular ways Gateway, Bridge and Wireless ISP to connect to the Internet. It’s recommended that you make use of the Gateway function. If you are sure of what kind of connection type your ISP provides, you can select the very type and click Next to go on configuring.
4. If you are sure of what kind of NTP server your Router, you can select the very type and click Next to go on configuring as shown in Figure 3-6.
Figure 3-6 Quick Setup - Time Zone Setting
- 11 -
AIP-W512
5. Confirm the IP address for your Router and click Next to continue configuration.
Figure 3-7 Quick Setup - LAN Interface Setting
6. If you select Gateway, the Router provides six connection types for your ISP provides. Make sure the cable is securely plugged into the WAN port before continuing.
a) If the connection type is PPPoE, then select it from drop down menu as shown below.
Enter the User Name and Password provided by your ISP, and click Next.
Figure 3-8 Quick Setup - WAN Interface Setting
- 12 -
AIP-W512
User Name/Password - Enter the User Name and Password provided by your ISP.
These fields are case sensitive. If you have difficulty with this process, please contact your ISP.
b) If the connection type detected is DHCP Client, the next screen will appear as shown in
Figure 3-9. You can then proceed with the wireless configuration.
Figure 3-9 Quick Setup - DHCP
c) If the connection type detected is Static IP, the next screen will appear as shown in
Figure 3-10.
Figure 3-10 Quick Setup - Static IP
- 13 -
AIP-W512
IP Address - This is the WAN IP address as seen by external users on the Internet
(including your ISP). Enter the IP address into the field.
Subnet Mask - The Subnet Mask is used for the WAN IP address, usually
255.255.255.0.
Default Gateway - Enter the gateway IP address into the box if required.
Primary DNS - Enter the DNS Server IP address into the box if required.
7. Click Next to continue, the Wireless settings page will appear as shown in Figure 3-11.
Figure 3-11 Quick Setup – Wireless
Band: Keep the default setting: 2.4GHz (B+G+N). If you just want to use a specific
protocol, please use the drop down menu to select it.
Mode: This field determines the wireless mode which the AIP-W512 works on.
Network Type: Keep the default setting: Infrastructure. If you just want to use another
operation mode, please use the drop down menu to select it.
SSID: Create a unique and easy way to remember the name of your wireless network.
You can also keep default settings without the device being affected.
- 14 -
AIP-W512
Channel Width - Select any channel width from the pull-down list. The default setting is
automatic therefore it can adjust the channel width for your clients automatically.
Channel Number- This field determines which operating frequency will be used. The
default channel is set to Auto allowing the AIP-W512 to choose the best channel automatically. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.
8. Set your security preference then click the Finished button.
Wireless Security: Recommend to choose WPA-PSK/WPA2-PSK and enter a Security Key using ASCII characters between 8 and 63 characters or 64 hexadecimal characters in the PSK Password filed. For advanced settings, please refer to Section 4.6: “Wireless”.
WPA-PSK/WPA2-PSK - Select WPA based on pre-shared passphrase.
PSK Password - You can enter ASCII or Hexadecimal characters.
For ASCII, the key can be made up of any numbers from 0 to 9 and any letters from A to Z, the length should be between 8 and 63 characters.
For Hexadecimal, the key can be made up of any numbers 0 to 9 and letters A to F, the length should be between 8 and 64 characters.
Please note the key is case sensitive, therefore the upper and lower case keys will affect the outcome. It is highly recommended to write down the key and all related wireless security settings.
Figure 3-12 Quick Setup - Finish
- 15 -
Loading...
+ 46 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use