Stainless Steel Top Kitchen Island
Dear Our Valuable Customers.
Please follow our assembly instructions in every step,
we guarantee that you will get the perfect merchandise.
Thank you so much for purchasing our quality products.
Part List
A.
Top
1 pc.
Side Frame
E.
Back Rail
1 pc.
I.
F.
Divider
1 pc.
Drawer
(Knock-Down Construction, please refer to
the page (4/4) of these instructions for
steps to complete assembling drawers)
2 drawers
Hardware List
B.
1 pc.
G.
Base
1 pc.
C.
Side Frame
1 pc.
H.
Shelf
1 pc.
D.
Front Rail
2 pcs.
J.
Side Bar
1 pc.
Head Cap Bolt (short)
(for Side Bar)
2 pcs. (+1 Extra)
Caster
Two casters with lock
Two casters without lock
4 pcs.
Tools Required For Assembly : Philips screwdriver
Hex Wrench
1 pc.
Wood Plug
13 pcs.
(+1 Extra)
Head Cap Bolt
15 pcs. (+1Extra)
Cam Lock Screw
4 pcs.(+1 Extra)
Cam Lock
4 pcs.(+1 Extra)
Wood Screw
Short 6 x ½”
(for Drawer Bottom Part)
12 pcs.(+1 Extra)
Wood Screw
Long 6 x 1”
(for Drawer Side Part)
16 pcs.(+1 Extra)
Machine Screw
for Pull Handle
4 pcs.
Pull Handle
2 pc.
Supporting Pin
4 pcs. (+1 Extra)
Assembly Instructions 2/4
IMPORTANT
Do not tighten up all the screws until each part is properly assembled. You should keep Hex Wrench in the safe place as
you may need to tighten up the Head Cap Bolts in the future.
STEP 1
Turn the Side Frame (B) upside down
on the soft material.
Attach the locking caster to the leg with sign,
and the non-locking caster to the other leg.
Do the same for the Side Frame (C).
Head Cap Bolt
B
D
E
Non-Locking Caster
Locking Caster
B
STEP 2
Attach the Front Rail (D)
and Back Rail (E) to the
Side Frame (B).
Head Cap Bolt
STEP 3
Attach the Divider (F) and another
Front Rail to the assembled unit.
Head Cap Bolt
F
D
D
Head Cap Bolt
STEP 4
Assembly Instructions 3/4
Head Cap Bolt
Attach the Base (G)
and Side Frame (C)
to the assembled unit.
Head Cap Bolt
C
Cam Lock Screw
C
G
Head Cap Bolt (short)
Head Cap Bolt
STEP 5
Attach the Side Bar (J)
to the Side Frame (C).
J
See the “Arrow”
on top
Cam Lock
A
A
STEP 6
Put the Cam Lock Screws into the holes at the
back of the Top (A).
Place the Top (A) on the assembled unit.
Place the Cam Locks into the holes of the
Side Frame (B) and (C).Make sure the Arrow sign
is on top. Tighten up all the Cam Locks to secure
the Top with the body. Insert the Supporting Pins
into both side frames at the desired level.
Place Shelf (H) and slide the Drawers (I)
into place.
STEP 7
Cover all holes with Wood Plugs
I
Supporting Pins
I
H
Supporting Pins
Assembly Instructions 4/4
Drawer
I4
I2
Figure 2
Turn the assembled drawer over and slide the
Plywood Bottom Part (I5) into the grooves
of Side Parts (I3) and (I4). Be sure to push
the plywood bottom part all the way forward,
so it meets the Front Part (I1).
I1
I3
Slider Wheel
Figure 1
Line up Side Parts (I3) and (I4) to the
Front Part (I1) and Back Part (I2). Make sure
the sign on each part is going down.
Using a Philips screwdriver, insert 1” screws
into each of the 4 pre-drilled holes on the
sides (I3) and (I4), then tighten half way.
I3
I5
I1
Insert the remaining ½” screws (6 pcs.)
into the pre-drilled holes at the Bottom Part
(I5), then tighten up all screws
Figure 3
Assemble the Pull Handle
to the Front Part (I1)
with Machine Screw.
Part List
I1.
Front Part
2 pcs.
I2.
Back Part
2 pcs.
Side Part
I1
I3.
2 pcs.
I4.
Side Part
2 pcs.
I2
I4
I5.
Bottom Part
2 pcs.
Loading...