Alcatel 7368 User Manual

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Alcatel-Lucent 7368

INTELLIGENT SERVICES ACCESS MANAGER ONT

G - 2 40W- B

Alcatel-Lucent
Thi s doc ument contain s propriet ary info rmat io n of Al cat el-Lu ce nt and is not t o be
or used except in accordance wi th applicable
Copyright 2014 © Alcatel-Lucent. All righ ts

Proprietary

P R

O D U C T

agreements.

reserved.

G U IDE

disclosed

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Alcatel-Lucent assumes no responsibility for the accuracy of the information presented, which is
subject to change without notice.

Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All
other trademarks are the property of their respective owners.

Copyright 2014 Alcatel-Lucent.
All rights reserved.

Disclaimers

Alcatel-Lucent products are intended for commercial uses. Without the appropriate network design
engineering, they must not be sold, licensed or otherwise distributed for use in any hazardous
environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft
navigation or communication systems, air traffic control, direct life-support machines, or weapons
systems, in which the failure of products could lead directly to death, personal injury, or severe physical
or environmental damage. The customer hereby agrees that the use, sale, license or other
of

the products for any such application without the prior written consent of Alcatel-Lucent, shall be at

distribution

the customer's sole risk. The customer hereby agrees to defend and hold Alcatel-Lucent harmless from
any claims for loss, cost, damage, expense or liability that may arise out of or in connection with the
use, sale, license or other distribution of the products in such applications.

This document may contain information regarding the use and installation of non-Alcatel-Lucent
products. Please note that this information is provided as a courtesy to assist you. While Alcatel-Lucent
tries to ensure that this

information accurately

reflects

information provided

by the

supplier,

please refer
to the materials provided with any non-Alcatel-Lucent product and contact the supplier for
confirmation. Alcatel-Lucent assumes no responsibility or liability for incorrect or incomplete
information provided about non-Alcatel-Lucent products.

However, this does not constitute a representation or warranty. The warranties provided for
Alcatel-Lucent products, if any, are set forth in contractual documentation entered into by
Alcatel-Lucent and its customers.

This document was originally written in English. If there is any conflict or inconsistency between the
English version and any other version of a document, the English version shall prevail.

When printed by Alcatel-Lucent, this document is printed on recycled paper.

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Preface

This preface provides general information about the documentation set for optical
network terminals (ONTs).

Scope

This documentation set provides information about safety, features and
functionality, ordering, hardware installation and maintenance, and software
installation procedures for the current release.

Audience

This documentation set is intended for planners, administrators, operators, and
maintenance personnel involved in installing, upgrading, or maintaining the ONTs.

Required knowledge

The reader must be familiar with general telecommunications principles.

Acronyms and initialisms

The expansions and optional descriptions of most acronyms and initialisms appear
in the glossary.

Alcatel-Lucent 7368 ISAM ONT iii
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Preface

Assistance and ordering phone numbers

Alcatel-Lucent provides global technical support through regional call centers.
Phone numbers for the regional call centers are available at the following URL:
http://www.alcatel-lucent.com/myaccess.

For ordering information, contact your Alcatel-Lucent sales representative.

Alcatel-Lucent quality processes

Alcatel-Lucent’s ONT manufacturing, testing, and inspecting practices are in
compliance with GR-1252-CORE and TL 9000 requirements. These requirements
are documented in the Operations Quality Plan
Alcatel North American Quality Manual
Wireline Network Quality Manual 8AB-83179-0001-QRAAA.

The quality plans and practices adequately ensure that technical requirements and
customer end-point requirements are met. The customer or its representatives may
be allowed to perform on-site quality surveillance audits, as agreed upon during
contract negotiations.

8BD-00023-4204-QRZZA,

8BD-00001-0000-QRZZA,

the

and the

Safety information

For safety information, see the appropriate safety guidelines chapter.

Documents

Documents are available using ALED or OLCS.

Procedure 1 To download a ZIP file package of the customer
documentation

1 Navigate to

and password. If you are a new user and require access to this service, please
contact your Alcatel-Lucent sales representative.

2 From the Technical Content for drop-down menu, choose the product.

3 Click on Downloads: Electronic Delivery.

4 Choose Documentation from the drop-down menu and click Next.

5 Select the image from the drop-down menu and click Next.

6 Follow the on-screen directions to download the file.

iv Alcatel-Lucent 7368 ISAM ONT

http://www.alcatel-lucent.com/myaccess

and enter your user name

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Preface

Procedure 2 To access individual documents

Individual PDFs of customer documents are also accessible through the Alcatel-Lucent
Customer Support website.

1 Navigate to

and password. If you are a new user and require access to this service, please
contact your Alcatel-Lucent sales representative.

2 From the Technical Content for drop-down menu, choose the product.

3 Click on Manuals and Guides to display a list of customer documents by title and

part number. You can filter this list using the Release drop-down menu.

4 Click on the PDF to open or save the file.

http://www.alcatel-lucent.com/myaccess

and enter your user name

Special information

The following are examples of how special information is presented in this
document.

Danger — Danger indicates that the described activity or situation

may result in serious personal injury or death; for example, high
voltage or electric shock hazards.

Danger indique que l'activité ou la situation décrite
peuvent entraîner des blessures corporelles graves ou mortelles;
par exemple, haute tension ou de risques d'électrocution.

Warning — Warning indicates that the described activity or situation

may, or will, cause equipment damage or serious performance
problems.

Warning indique que l'activité ou la situation décrite ne
peut, ou la volonté, des dommages matériels de cause ou de graves
problèmes de performance

Caution — Caution indicates that the described activity or situation

may, or will, cause service interruption.

Caution indique que l'activité ou la situation décrite

Procedures with options or substeps

When there are options in a procedure, they are identified by letters. When there are
required substeps in a procedure, they are identified by roman numerals.

peut, ou la volonté, le service de la cause interruption.

Note — A note provides information that is, or may be, of special

interest.

Une note fournit des informations qui est, ou peut être,

d'un intérêt particulier.

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Preface

Procedure 3 Example of options in a procedure

At step 1, you can choose option a or b. At step 2, you must do what the step indicates.

1 This step offers two options. You must choose one of the following:

a This is one option.

b This is another option.

2 You must perform this step.

Procedure 4 Example of required substeps in a procedure

At step 1, you must perform a series of substeps within a step. At step 2, you must do
what the step indicates.

1 This step has a series of substeps that you must perform to complete the step. You

must perform the following substeps:

i This is the first substep.

ii This is the second substep.

iii This is the third substep.

2 You must perform this step.

Multiple PDF document search

You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a
common term. Adobe Reader displays the results in a single display panel. The

vi Alcatel-Lucent 7368 ISAM ONT

results are grouped by PDF file, and you can expand the entry for each file.

Note — The PDF files in which you search must be in the same

folder.

être dans le même dossier

Procedure 5 To search multiple PDF files for a common term

1 Open Adobe Acrobat Reader.

2 Choose Edit→Search from the Acrobat Reader main menu. The Search PDF panel

appears.

3 Enter the search criteria.

Les fichiers PDF dans lequel vous recherchez doivent

Edition 01

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Preface

4 Click on the All PDF Documents In radio button.

5 Select the folder in which to search using the drop-down menu.

6 Click on the Search button.

Acrobat Reader displays the search results. You can expand the entries for each
document by clicking on the + symbol.

Alcatel-Lucent 7368 ISAM ONT vii
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ETSI ONT safety guidelines

This chapter provides information about the mandatory regulations that govern the
installation and operation of the optical network terminals (ONTs).

Safety instructions

This section describes the safety instructions that are provided in the ONT customer
documentation and on the equipment.

Safety instruction boxes

The safety instruction boxes are provided in the ONT customer documentation.
Observe the instructions to meet safety requirements.

The following is an example of the Danger box.

Danger — Possibility of personal injury.

Possibilité de blessures.

The Danger box indicates that the described activity or situation may pose a threat to
personal safety. It calls attention to a situation or procedure which, if not correctly
performed or adhered to, may result in death or serious physical harm.

Do not proceed beyond a Danger box until the indicated conditions are fully
understood and met.

The following is an example of the Warning box.

Warning 1 — Possibility of equipment damage.
Possibilité de dommages matériels.

Warning 2 — Possibility of data loss.
Possibilité de perte de données.

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Description

Label text

ESD warning

Caution: This assembly contains an electrostatic sensitive device.

Laser classification

Class 1 laser product

PSE marking

These power supplies are Japan PSE certified and compliant with
Japan VCCI emissions standards.

ETSI ONT safety guidelines

The Warning box indicates that the described activity or situation may, or will, cause
equipment damage, loss of data, or serious performance problems. It identifies a
possible equipment-damaging situation or provides essential information to avoid
the degradation of system operations or data.

Do not proceed beyond a warning until the indicated conditions are fully understood
and met.

The following is an example of the Caution box.

The Caution box indicates that the described activity or situation may, or will, cause
service interruption.

Do not proceed beyond a caution until the indicated conditions are fully understood
and met.

The following is an example of the Note box.

Caution 1 — Possibility of service interruption.
Possibilité d'interruption de service.

Caution 2 — Service interruption.

Interruption de service

Note — Information of special interest.

The Note box provides information that assists the personnel working with ONTs. It
does not provide safety-related instructions.

Safety-related labels

The ONT equipment is labeled with the specific safety instructions and compliance
information that is related to a variant of the ONT. Observe the instructions on the
safety labels.

Table 1 provides sample safety labels on the ONT equipment.

Figure 1 shows the PSE certification.

x Alcatel-Lucent 7368 ISAM ONT

L'information d'intérêt spécial.

Table 1 Safety labels

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Warning

This is a

Class B product based

on the

standard

of

the Voluntary Control Council

for Interference

from Information Technology Equipment (VCCI).

If this is

used near a radio

or

television receiver

in

a

domestic environment,

it may

cause radio interference. Install

and use the

equipment

according

to the

instruction

manual.

Safety standards compliance

Alcatel-Lucent 7368 ISAM ONT xi
Edition 01
G-240W-B Product Guide

This section describes the ONT compliance with the European safety standards.

EMC, EMI, and ESD compliance

The ONT equipment complies with the following EMC, EMI, and ESD
requirements:

• EN 300-386 V1.3.2 (2003-05): Electromagnetic Compatibility and Radio

Spectrum Matters (ERM): Telecommunications Network Equipment;
Electromagnetic Compatibility (EMC) requirements; Electrostatic Discharge
(ESD) requirements

• EN 55022 (1998): Class B, Information Technology Equipment, Radio

Disturbance Characteristics, limits and methods of

• EN 55024 (1998): Information Technology Equipment, Immunity

Characteristics, limits and methods of measurement

• European Council Directive 2004/108/EC

• EN 300-386 V1.4.1: 2008

• EN 55022:2006 Class B (ONTs)

• EN EN 61000-3-2:2006

• EN EN 61000-3-3:2008

• IEC 61000-4-2:2001

• IEC 61000-4-3:2006

• IEC 61000-4-4:2004

• IEC 61000-4-5:2005

• IEC 61000-4-6:2003/A1:2004/A2:2006

• IEC 61000-4-11:2004

Equipment safety standard compliance

The ONT equipment complies with the requirements of EN 60950-1, Safety of
Information Technology Equipment for use in a restricted location (per R-269).

Figure 1 PSE certification

ETSI ONT safety guidelines

measurement

19841

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ETSI ONT safety guidelines

Environmental standard compliance

The ONT equipment complies with the EN 300 019 European environmental
standards.

Laser product standard compliance

For most ONTs, the ONT equipment complies with EN 60825-1 and IEC 60825-2
for laser products. If there is an exception to this
this information in the standards compliance section of the unit data sheet in this
Product Guide.

Resistibility requirements compliance

The ONT equipment complies with the requirements of ITU
for resistibility of telecommunication equipment installed in customer premises to
over voltage and overcurrents.

Acoustic noise emission standard compliance

The ONT equipment complies with EN 300 753 acoustic noise emission limit and
test methods.

Electrical safety guidelines

This section provides the electrical safety guidelines for the ONT equipment.

Note 1 — The ONTs comply with the U.S. National Electrical Code.

However, local electrical authorities have jurisdiction when there are
differences between the local and U.S. standards.

Les ONT sont conformes à la US National Electrical Code.

Cependant, les autorités locales électriques ont compétence quand il ya

Power supplies

The use of any
supported
contract with Alcatel-Lucent. Such use greatly increases the danger of damage to
equipment or property.

Cabling

The following are the guidelines regarding cables used for the ONT equipment:

• All cables must be approved by the relevant national electrical code.

• The cables for outdoor installation of ONTs must be suitable for outdoor use.

• POTS wiring run outside the subscriber premises must comply with the

requirements of local electrical codes. In some markets, the maximum allowed
length of the outside run is 140 feet (43 m). If the outside run is longer, NEC
requires primary protection at both the exit and entry points for the wire.

des différences entre les normes locales et américaines.

Note 2 — The ONTs comply with BS EN 61140.

BS EN 61140

non-Alcatel-Lucent approved

or

endorsed

compliance

regulation, you can find

Recommendation

Les ONT sont conformes à la norme

power supplies or power adapters is not

by

Alcatel-Lucent.

Such use will void any

warranty

K.21

or support

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ETSI ONT safety guidelines

Protective earth

Earthing and bonding of the ONTs must comply with the requirements of local
electrical codes.

ESD safety guidelines

The ONT equipment is sensitive to ESD. Operations personnel must observe the
following ESD instructions when they handle the ONT equipment.

Caution — This

equipment

is ESD sensitive. Proper ESD protections
should be used when you enter the TELCO Access portion of the
ONT.

Cet équipement est sensible ESD. Protections relatives

aux décharges électrostatiques doivent être utilisés lorsque vous
entrez dans la partie d'accès TELCO de l'ONT

During installation and maintenance, service personnel must wear wrist straps to
prevent damage caused by ESD.

Laser safety guidelines

Observe the following instructions when you perform installation, operations, and
maintenance tasks on the ONT equipment.

Only qualified service personnel who are extremely familiar with laser radiation
hazards should install or remove the fiber optic cables and units in this system.

Danger — There may be invisible laser radiation at the fiber optic

cable when the cable is removed from the connector. Avoid direct
exposure to the laser beam.

Il peut y avoir un rayonnement laser invisible sur le

câble à fibre optique lorsque le câble est retiré du connecteur.
Éviter l'exposition directe au rayon laser.

Observe the following danger for laser hazard. Eyes can be damaged when they are
exposed to a laser beam. Take necessary precautions before you plug in the optical
modules.

Danger — Possibility of equipment damage. Risk of eye damage by

laser radiation.
Possibilité de dommages matériels. Risque de lésions

oculaires par un rayonnement laser.

Laser classification

The ONT is classified as a Class 1 laser product based on its transmit optical output.

Laser warning labels

The following figures show the labels related to laser product, classification and
warning.

Figure 2 shows a laser product label.

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ETSI ONT safety guidelines

Figure 2 Laser product label

18455

Figure 3 shows a laser classification label. Laser classification labels may be
provided in other languages.

Figure 3 Laser classification label

CLASS 1 LASER

PRODUCT

PRODUCTO LASER CLASE

1

CLASE

1 DEL LASER

Figure 4 shows a laser warning label and an explanatory label for laser products.
Labels and warning may be provided in other languages. The explanatory label

xiv Alcatel-Lucent 7368 ISAM ONT

provides the following information:

• a warning that calls attention to the invisible laser radiation

• an instruction against staring into the beam or viewing directly with optical

instruments

• wavelength

• normal output power

• maximum output power

LASER CLASSE

G-240W-B Product Guide

1

18992

Edition 01

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Laser Warning

RADIACION

RAYO LASER.

Transmit optical output

The maximum transmit optical output of an ONT is +5 dBm.

Normal laser operation

In normal operation, fiber cable laser radiation is always off until it receives signal
from the line terminal card.

Eyes can be damaged when they exposed to a laser beam. Operating personnel must
observe the instructions on the laser explanatory label before plugging in the optical
module.

Danger — Risk of eye damage by laser radiation.
Risque de lésions oculaires par un rayonnement laser.

Location class

Use cable supports and guides to protect the receptacles from strain.

Alcatel-Lucent 7368 ISAM ONT xv
Edition 01
G-240W-B Product Guide

ETSI ONT safety guidelines

Figure 4 Laser warning labels

INVISIBLE LASER RADIATION
DO

NOT STARE INTO

OR

VIEW DIRECTLY
OPTICAL
Wavelength(s): xxxx
Normal output power:
Max

output power:

Label

CLASS 1 LASER

RAYONNEMENT LASER CLASSE 1

RAYONNEMENT LASER INVISIBLE EVITER

NE

PAS DEMONTER. FAIRE APPEL

INVISIBLE LASER RADIATION PRESENT
WHEN NOT CONNECTED. AVOID DIRECT EXPOSURE

TOUTE EXPOSITION

CLASE

DE

LASER INVISIBLE. EVITAR CUALOUIER EXPOSICION AL

NO

DESMONTAR. LLAMAR A PERSONAL AUTORIZADO

1 DEL

Laser Warning Label

Laser Warning

PRODUCT

AU

FAISCEAU

A UN

LASER

INSTRUMENTS

yyy m W

PERSONNELL QUALIFIE

AT

FIBER OPTIC CABLE

BEAM

WITH

nm

xx m W

Label

TO BEAM.

18993

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ETSI ONT safety guidelines

Environmental requirements

See the ONT technical specification documentation for more information about
temperature ranges.

During operation in the supported temperature range, condensation inside the ONT
caused by humidity is not an issue. To avoid condensation caused by rapid changes

xvi Alcatel-Lucent 7368 ISAM ONT

in temperature and humidity, Alcatel-Lucent recommends:

• The door of the ONT not be opened until temperature inside and outside the

enclosure has stabilized.

• If the door of the ONT must be opened after a rapid change in temperature or

humidity, use a dry cloth to wipe down the metal interior to prevent the risk of
condensation.

• When high humidity is present, installation of a cover or tent over the ONT helps

prevent condensation when the door is opened.

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ETSI environmental and CRoHS guidelines

This chapter provides information about the ETSI environmental China Restriction
of Hazardous Substances (CRoHS) regulations that govern the installation and
operation of the optical line termination (OLT) and optical network termination
(ONT) systems. This chapter also includes environmental operation parameters of

Alcatel-Lucent 7368 ISAM ONT xvii
Edition 01
G-240W-B Product Guide

general interest.

Environmental labels

This section describes the environmental instructions that are provided with the
customer documentation, equipment, and location where the equipment resides.

Overview

CRoHS is applicable to Electronic Information Products (EIP) manufactured or sold
and imported in the territory of the mainland of the People’s Republic of China. EIP
refers to
technology,
as batteries and cables.

Environmental related labels

Environmental labels are located on appropriate equipment. The following are
sample labels.

products

and their

including electronic

accessories manufactured

communications

products and such subcomponents

by using

electronic

information

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ETSI environmental and CRoHS guidelines

Products below Maximum Concentration Value (MCV) label

Figure 1 shows the label that indicates a product is below the maximum
concentration value, as defined by standard SJ/T11363-2006 (Requirements for
Concentration Limits for Certain Hazardous Substances in Electronic Information
Products). Products with this label are recyclable. The label may be found in this
documentation or on the product.

Figure 1 Products below MCV value label

18986

Products containing hazardous substances above Maximum Concentration
Value (MCV) label

Figure 2 shows the label that indicates a product is above the maximum
concentration value, as defined by standard SJ/T11363-2006 (Requirements for
Concentration Limits for Certain Hazardous Substances in Electronic Information
Products). The number contained inside the label indicates the
Environment-Friendly User Period (EFUP) value. The label may be found in this

xviii Alcatel-Lucent 7368 ISAM ONT

documentation or on the product.

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Figure 2 Products above MCV value label

ETSI environmental and CRoHS guidelines

18985

Together with major international telecommunications equipment companies,
Alcatel-Lucent has determined it is appropriate to use an EFUP of 50 years for
network infrastructure equipment and an EFUP of 20 years for handsets and
accessories.

These values are based on

manufacturers' extensive

practical experience
of the design, manufacturing, maintenance, usage conditions, operating
environments, and physical condition of infrastructure and handsets after years of
service. The values reflect minimum values and refer to products operated according
to the intended use conditions. See “Hazardous Substances Table (HST)” for more
information.

Hazardous Substances Table (HST)

This

section describes

the

compliance

of the OLT and ONT

equipment

to the CRoHS
standard when the product and subassemblies contain hazardous substances beyond
the MCV value. This information is found in this user documentation where part
numbers for the product and subassemblies are listed. It may be referenced in other
OLT and ONT documentation.

In accordance with the People’s Republic of China Electronic Industry Standard
Marking for the Control of Pollution Caused by Electronic Information Products
(SJ/T11364-2006), customers may access the Alcatel-Lucent Hazardous Substance
Table, in Chinese, from the following location:

• http://www.alcatel-sbell.com.cn/wwwroot/images/upload/private/1/media/ChinaR

oHS.pdf

Other environmental requirements

Observe the following environmental requirements when handling the P-OLT or

Alcatel-Lucent 7368 ISAM ONT xix
Edition 01
G-240W-B Product Guide

ONT equipment.

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ETSI environmental and CRoHS guidelines

ONT environmental requirements

See the ONT technical specification documentation for more information about
temperature ranges.

Storage

According to ETS 300-019-1-1 - Class 1.1, storage of OLT equipment must be in
Class 1.1, weather-protected, temperature-controlled locations.

Transportation

According

to EN

300-019-1-2

- Class 2.3,

transportation

of the OLT

equipment

must

be in packed, public transportation with no rain on packing allowed.

Stationary use

According to EN 300-019-1-3 - Class 3.1/3.2/3.E, stationary use of OLT equipment
must be in a temperature-controlled location, with no rain allowed, and with no
condensation allowed.

Thermal limitations

When the OLT is installed in the CO or CEV, install air filters on the P-OLT. The
thermal limitations for OLT operation in a CO or CEV are:

• operating temperature: 5°C to 40°C (41°F to 104°F)

• short-term temperature: –5°C to 50°C (23°F to 122°F)

• operating relative humidity: 5% to 85%

• short-term relative humidity: 5% to 95%, but not to exceed 0.024 kg of water/kg

Material content compliance

European Union (EU) Directive 2002/95/EC, “Restriction of the use of certain
Hazardous Substances” (RoHS), restricts the use of lead, mercury, cadmium,
hexavalent chromium, and certain flame retardants in electrical and electronic
equipment. This Directive applies to electrical and electronic products placed on the
EU market after 1 July 2006, with various exemptions, including an exemption for
lead solder in network infrastructure equipment. Alcatel-Lucent products shipped to
the EU after 1 July 2006 comply with the EU RoHS Directive.

Alcatel-Lucent has implemented a
The process is described in: Alcatel-Lucent process for ensuring RoHS Compliance
(1AA002660031ASZZA).
Directive 2011/65/EU

This ensures compliance with the European Union

on the
in Electrical and Electronic Equipment (RoHS2). With the process equipment is
assessed in accordance with the Harmonised Standard EN50581:2012 (CENELEC)
on Technical documentation for the assessment of electrical and electronic products
with respect to the restriction of hazardous substances.

xx Alcatel-Lucent 7368 ISAM ONT

material/substance

Restriction

of the Use of

content management process.

Certain Hazardous

G-240W-B Product Guide

Substances

Edition 01

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ETSI environmental and CRoHS guidelines

End-of-life collection and treatment

Electronic products bearing or referencing the symbol shown in Figure 3, when put
on the market within the European Union (EU), shall be collected and treated at the
end of their useful life, in compliance with applicable EU and local legislation. They
shall not be disposed of as part of unsorted municipal waste. Due to materials that
may be contained in the product, such as heavy metals or batteries, the environment
and human health may be negatively impacted as a result of inappropriate disposal.

Note — In the European Union, a solid bar under the symbol for a

crossed-out wheeled bin indicates that the product was put on the
market after 13 August 2005.

Dans l'Union européenne, un bar solide sous le symbole
d'une poubelle sur roues barrée d'une croix indique que le produit
a été mis sur le marché après le 13 Août 2005.

Figure 3 Recycling/take back/disposal of product symbol

At the end of their life, the OLT products are subject to the applicable local
legislations that implement the European Directive 2002/96EC on waste electrical
and electronic equipment (WEEE).

There can be different
states of the European Union.

In compliance with legal requirements and contractual agreements, where
applicable, Alcatel-Lucent will offer to provide for the collection and treatment of
Alcatel-Lucent

products bearing the logo shown in Figure 3 at the end of their useful
life, or products displaced by Alcatel-Lucent equipment offers. For information
regarding take-back of equipment by Alcatel-Lucent, or for more information
regarding the requirements for recycling/disposal of product, contact your
Alcatel-Lucent account manager or Alcatel-Lucent take back support at
[e-mail].

Alcatel-Lucent 7368 ISAM ONT xxi

requirements

for collection and treatment in different member

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ANSI ONT safety guidelines

This chapter provides information about the mandatory regulations that govern the
installation and operation of the optical network terminals or units (ONTs or ONUs)

Alcatel-Lucent 7368 ISAM ONT xxiii
Edition 01

in the North American or ANSI market.

Safety instructions

This section describes the safety instructions that are provided in the ONT customer
documentation and on the equipment.

Safety instruction boxes in customer documentation

The safety instruction boxes are provided in the ONT customer documentation.
Observe the instructions to meet safety requirements.

The following is an example of the Danger box.

Danger — Possibility of personal injury.
Possibilité de blessures

The Danger box indicates that the described activity or situation may pose a threat to
personal safety. It calls attention to a situation or procedure which, if not correctly
performed or adhered to, may result in death or serious physical harm.

Do not proceed beyond a Danger box until the indicated conditions are fully
understood and met.

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Description

Label text

UL compliance

Communication service equipment US listed. Type 3R enclosure ­Rainproof.

TUV compliance

Type 3R enclosure - Rainproof.

ESD warning

Caution: This assembly contains electrostatic sensitive device.

ANSI ONT safety guidelines

The following is an example of the Warning box.

The Warning box indicates that the described activity or situation may, or will, cause
equipment damage, loss of data, or serious performance problems. It identifies a
possible equipment-damaging situation or provides essential information to avoid
the degradation of system operations or data.

Do not proceed beyond a warning until the indicated conditions are fully understood
and met.

The following is an example of the Caution box.

The Caution box indicates that the described activity or situation may, or will, cause
service interruption.

Do not proceed beyond a caution until the indicated conditions are fully understood
and met.

The following is an example of the Note box.

Warning 1 — Possibility of equipment damage.

Possibilité de dommages matériels

Warning 2 — Possibility of data loss.

Possibilité de perte de données.

Caution 1 — Possibility of service interruption.

Possibilité d'interruption de service

Caution 2 — Service interruption.

Interruption de service.

Note — Information of special interest.

The Note box provides information that assists the personnel working with ONTs. It
does not provide safety-related instructions.

Safety-related labels

The ONT equipment is labeled with specific safety compliance information and
instructions that are related to a variant of the ONT. Observe the instructions on the
safety labels.

Table 1 provides examples of the text in the various ONT safety labels.

(1 of 2)

L'information d'intérêt spécial.

Table 1 Safety labels

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Description

Label text

Laser classification

Class 1 laser product

Laser product compliance

This laser product conforms to all applicable standards of 21 CFR

1040.10 at date of manufacture.

FCC standards compliance

Tested to comply with FCC standards for home or office use.

CDRH compliance

Complies with 21 CFR 1040.10 and 1040.11 except for deviations
pursuant to Laser Notice No. 50, dated June 24, 2007

Operation conditions

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.

Canadian standard
compliance (modular ONT)

This Class A digital apparatus complies with Canadian ICES-003.

Canadian standard
compliance (outdoor ONT)

This Class B digital apparatus complies with Canadian ICES-003.
CE marking

There are various CE symbols for CE compliance.

Tested

to Comply

with FCC Standards

FOR HOME OR OFFICE

USE

COMMUNICATION SERVICE

EQUIPMENT

c

®

US LISTED
27FY
Type 3R Enclosure

- Rainproof

This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause

harmful

interference, and (2) this device must accept any

interference

received, including interference that may cause undesired

operation.

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil
numerique de la class A est conforme a la norme NMB-003 du

Canada

CAUTION

This Assembly Contains Electrostatic Sensitive Devices

ANSI ONT safety guidelines

(2 of 2)

Figure 1 shows a sample safety label on the ONT equipment.

Figure 1 Sample safety label on the ONT equipment

Safety standards compliance

This section describes the ONT compliance with North American safety standards.

Warning — Changes or modifications to this unit not expressly

approved by the party responsible for compliance could void the
user's authority to operate the equipment.

non expressément approuvés par la partie responsable de la
conformité pourraient annuler l'autorité de l'utilisateur à utiliser
l'équipement.

Les changements ou modifications de cette unité

18533

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ANSI ONT safety guidelines

EMC, EMI, and ESD standards compliance

The ONT equipment complies with the following requirements:

• Federal Communications Commission (FCC) CFR 47, Part 15, Subpart B, Class

A requirements for OLT

equipment

• GR-1089-CORE requirements, including:

• Section 3 Electromagnetic Interference, Emissions Radiated and Conducted

• Section 3 Immunity, Radiated and Conducted

• Section 2 ESD

Immunity: Electrically Fast Transients

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.

However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

Discharge Immunity:

System Level

Electrostatic Discharge

and EFT

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is needed.

• Consult the dealer or an experienced radio/TV technician for help.

Equipment safety standard compliance

The ONT equipment complies with the requirements of UL60950-1, Outdoor ONTs
to “Communication Service Equipment” (CSE) and Indoor ONTs to Information
Technology Equipment (ITE).

Environmental standards compliance

The ONT equipment complies with the following standards:

• GR-63-CORE (NEBS): requirements related to operating, storage, humidity,

altitude, earthquake, office vibration, transportation and handling, fire resistance
and spread, airborne contaminants, illumination, and acoustic noise

• GR-487-CORE: requirements related to rain, chemical, sand, and dust

• GR-487 R3-82: requirements related to condensation

• GR-3108: Requirements for Network Equipment in the Outside Plant (OSP)

xxvi Alcatel-Lucent 7368 ISAM ONT

• TP76200: Common Systems Equipment Interconnections Standards

G-240W-B Product Guide

Edition 01

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ANSI ONT safety guidelines

Laser product standards compliance

The ONT equipment complies with 21 CFR 1040.10 and CFR 1040.11, except for
deviations pursuant to Laser Notice No. 50, dated June 24, 2007” or to 21 CFR

1040.10 U.S. Center for Devices and Radiological Health (CDRH) of the Food and
Drug Administration (FDA) Laser Notice 42 for ONTs containing Class 1 Laser
modules certified by original manufactures.

Per CDRH 21 CFR 10.40.10 (h) (1) (iv) distributors of Class 1 laser products, such
as ALU ONTs shall leave the following Laser Safety cautions with the end user.

a) “Class 1 Laser Product”
b)

“Caution

– Use of

controls

or

adjustments

or

performance

of

procedures

other than

those specified herein may result in hazardous radiation exposure.”
Figure 2 shows a laser product label.

Figure 2 Sample laser product label showing CDRH 21 CFR compliance

4P92

No User Serviceable Parts Inside. Refer All Servicing To Qualified Personnel.

I.T.E

Complies with 21 CFR 1040.10 and

1040.11 except for deviations pursuant to
Laser Notice No. 50, dated June 24, 2007.

12VDC 2.5A

Resistibility requirements compliance

The ONT equipment complies with the requirements of ITU
for resistibility of telecommunication equipment installed in customer premises to
overvoltage and overcurrents.

Recommendation

K.21

Laser safety guidelines

Only qualified service personnel who are extremely familiar with laser radiation
hazards should install or remove the fiber optic cables and units in this system.

Observe the following warnings when you perform installation, operations, and
maintenance tasks on the ONT equipment.

Danger — There may be invisible laser radiation at the fiber optic

cable when the cable is removed from the connector. Avoid direct
exposure to beam.

Il peut y avoir un rayonnement laser invisible sur le

câble à fibre optique lorsque le câble est retiré du connecteur.

Alcatel-Lucent 7368 ISAM ONT xxvii

Éviter l'exposition directe au rayon

22813

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ANSI ONT safety guidelines

Observe the following danger for a laser hazard. Eyes can be damaged when they are
exposed to a laser beam. Take necessary precautions before you plug in the optical
modules.

Danger — Possibility of equipment damage. Risk of eye damage by

laser radiation.

Possibilité de dommages matériels. Risque de lésions

oculaires par un rayonnement laser.

Per CDRH 21 CFR 10.40.10 (h) (1) (iv) distributors of Class 1 laser products, such
as ALU ONTs shall leave the following Laser Safety cautions with the end user.

a) “Class 1 Laser Product”
b)

“Caution

– Use of

those specified herein may result in hazardous radiation exposure.”

Laser warning labels

The following figures show sample labels related to laser product, classification and
warning.

Figure 3 shows a laser product label.

Figure 4 shows a laser classification label. Laser classification labels may be
provided in other languages.

CLASS 1 LASER

xxviii Alcatel-Lucent 7368 ISAM ONT

CLASE

controls

1 DEL LASER

or

adjustments

Figure 3 Laser product label

Figure 4 Laser classification label

PRODUCT

or

performance

PRODUCTO LASER CLASE

of

procedures

LASER CLASSE

other than

18455

1

1

18992

Edition 01

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ANSI ONT safety guidelines

Figure 5 shows a laser warning label and an explanatory label for laser products.
Explanatory labels may be provided in other languages. The explanatory label
provides the following information:

• a warning that calls attention to the invisible laser radiation

• an instruction against staring into the beam or viewing directly with optical

instruments

• wavelength

• normal output power

• maximum output power

Figure 5 Laser warning labels

INVISIBLE LASER RADIATION
DO

NOT STARE INTO

OR

VIEW DIRECTLY
OPTICAL
Wavelength(s): xxxx
Normal output power:
Max

INSTRUMENTS

output power:

BEAM

WITH

nm

xx m W

yyy m W

Laser Warning

Label

Laser Warning

CLASS 1 LASER

PRODUCT

RAYONNEMENT LASER CLASSE 1

RAYONNEMENT LASER INVISIBLE EVITER

NE

PAS DEMONTER. FAIRE APPEL

RADIACION

RAYO LASER.

INVISIBLE LASER RADIATION PRESENT
WHEN NOT CONNECTED. AVOID DIRECT EXPOSURE

TOUTE EXPOSITION

DE

LASER INVISIBLE. EVITAR CUALOUIER EXPOSICION AL

NO

CLASE

DESMONTAR. LLAMAR A PERSONAL AUTORIZADO

1 DEL

AU

FAISCEAU

A UN

PERSONNELL QUALIFIE

LASER

AT

FIBER OPTIC CABLE

Laser Warning Label

Label

TO BEAM.

18993

Laser classification

The ONT is classified as a Class 1 laser product based on its transmit optical output.
For Class 1 laser products, lasers are safe under reasonably foreseeable conditions of

operation, including the use of optical instruments for intrabeam viewing.
Figure 6 shows a sample laser product safety label on the ONT equipment.

Alcatel-Lucent 7368 ISAM ONT xxix
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

CLASS 1 LASER PRODUCT

THIS LASER PRODUCT CONFORMS TO ALL APPLICABLE

STANDARDS OF

21

CFR 1040.10

AT

DATE OF MANUFACTURE.

MANUFACTURED:

MONTH

YEAR

ANSI ONT safety guidelines

Figure 6 Sample laser product safety label on the ONT equipment

Transmit optical output

The maximum transmit optical output of an ONT is +5 dBm.

Normal laser operation

In normal operation, fiber cable laser radiation is always off until it receives signal
from the line terminal card.

Operating personnel must observe the instructions on the laser explanatory label
before plugging in the optical module.

Danger — Risk of eye damage by laser radiation.
Risque de lésions oculaires par un rayonnement laser.

Location class

Use cable supports and guides to protect the receptacles from strain.

Electrical safety guidelines

This section provides the electrical safety guidelines for the ONT equipment.

Note — The ONTs comply with the U.S. National Electrical Code.

However, local electrical authorities have jurisdiction when there are
differences between the local and U.S. standards.

Cependant, les autorités locales électriques ont compétence quand il
ya des différences entre les normes locales et américaines.

Power supplies

The use of any
supported
contract with Alcatel-Lucent. Such use greatly increases the danger of damage to
equipment or property.

non-Alcatel-Lucent approved

or

endorsed

18532

Les ONT sont conformes à la US National Electrical Code.

power supplies or power adapters is not

by

Alcatel-Lucent.

Such use will void any

warranty

or support

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Cabling

The following are the guidelines regarding cables used for the ONT equipment:

• Use only cables approved by the relevant national electrical code.

• Use cables suitable for outdoor use for outdoor installation of ONTs.

• The ONTs have been evaluated for use with external POTS wiring without

primary protection that may not exceed 140 ft (43 m) in reach. However, the
power cable must not exceed 100 ft (31 m).

Protective earth

Earthing and bonding of the ONTs must comply with the requirements of NEC
article 250 or local electrical codes.

ESD safety guidelines

The ONT equipment is sensitive to ESD. Operations personnel must observe the
following ESD instructions when they handle the ONT equipment.

Caution — This

should be used when en tering the TELCO Access portion of the ONT.

appropriées doivent être utilisées lors de l'entrée de la partie TELCO
accès de l'ONT

During installation and maintenance, service personnel must wear wrist straps to
prevent damage caused by ESD.

Alcatel-Lucent recommends that you prepare the site before you install the ONT
equipment. In addition, you must control relative humidity, use static dissipating
material for furniture or flooring, and restrict the use of air conditioning.

Environmental requirements

See the ONT technical specification documentation for temperature ranges for
ONTs.

During operation in the supported temperature range, condensation inside the ONT
caused by humidity is not an issue. To avoid condensation caused by rapid changes
in temperature and humidity, Alcatel-Lucent recommends:

• The door of the ONT not be opened until temperature inside and outside the

enclosure has stabilized.

• If the door of the ONT must be opened after a rapid change in temperature or

humidity, use a dry cloth to wipe down the metal interior to prevent the risk of
condensation.

• When high humidity is present, installation of a cover or tent over the ONT helps

prevent condensation when the door is opened.

Alcatel-Lucent 7368 ISAM ONT xxxi

ANSI ONT safety guidelines

equipment

is ESD sensitive. Proper ESD protections

Cet équipement est sensible ESD. Protections ESD

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Contents

Preface iii

Scope
Audience
Required
Acronyms and initialisms
Assistance and ordering phone numbers
Alcatel-Lucent quality
Safety
Documents

Special

Multiple PDF document

ETSI ONT safety guidelines

Safety

Safety standards

Alcatel-Lucent 7368 ISAM ONT xxxiii
Edition 01
G-240W-B Product Guide

...............................................................................................

...............................................................................................

knowledge ...................................................................................

.............................................................................

...........................................................

processes ....................................................................

information .....................................................................................

..............................................................................................

Procedure 1 To download a ZIP file package of the customer

documentation.................................................................... iv

Procedure 2 To access individual

information ..................................................................................... v

Procedures with options or
Procedure 3 Example of options in a

Procedure 4 Example of required substeps in a

search....................................................................... vi

Procedure 5 To search multiple PDF files for a common

instructions ..................................................................................... ix

Safety instruction boxes
Safety-related labels

compliance.........................................................................

EMC, EMI, and ESD
Equipment safety standard compliance
Environmental standard
Laser product standard

.............................................................. ix

................................................................... x

compliance.......................................................

compliance ...............................................

compliance ................................................

documents ...................................... v

substeps ................................................. v

procedure.................................. vi

procedure ..................... vi

term ................. vi

............................................

iii
iii
iii
iii

iv
iv
iv

iv

ix

xi
xi
xi

xii

xii

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Contents

ETSI environmental and CRoHS guidelines

ANSI ONT safety guidelines

Resistibility requirements
Acoustic noise emission standard

Electrical safety

ESD safety
Laser safety

Environmental

Environmental

Hazardous Substances Table

Other environmental

Safety

Safety standards

Laser safety

instructions .................................................................................. xxiii

guidelines.......................................................................... xii

Power

Cabling .................................................................................. xii

Protective

guidelines ................................................................................ xiii

guidelines .............................................................................. xiii

Laser

Transmit optical
Normal laser
Location

Overview
Environmental related

ONT environmental

Storage..................................................................................

Transportation
Stationary use
Thermal
Material content

End-of-life collection and treatment ..............................................xxi

Safety instruction boxes in customer
Safety-related labels

EMC, EMI, and ESD standards
Equipment safety standard compliance
Environmental standards
Laser product standards
Resistibility requirements
guidelines
Laser warning
Laser
Transmit optical
Normal laser
Location

supplies......................................................................... xii

classification................................................................... xiii

class ..........................................................................

requirements ........................................................................xvi

labels ................................................................................ xvii

requirements

limitations ...................................................................

compliance.......................................................................

.............................................................................xxvii

classification..................................................................

class .........................................................................

compliance ............................................. xii

compliance .................................... xii

earth ...................................................................... xiii

output ..............................................................

operation ...............................................................

xvii

.............................................................................. xvii

labels....................................................... xvii

(HST)................................................................. xix

................................................................xix

requirements ..................................................

.........................................................................

.........................................................................

compliance ........................................................

xxiii

documentation ......................... xxiii

............................................................... xxiv

compliance .......................................

.........................................

compliance ............................................

compliance

compliance

labels ...............................................................

output .............................................................

operation ..............................................................

.............................................xxvii

...........................................xxvii

xxviii

xxxiv Alcatel-Lucent 7368 ISAM ONT

Edition 01

G-240W-B Product Guide

xv
xv

xv

xx
xx
xx
xx
xx
xx

xxv
xxvi
xxvi
xxvi

xxix

xxx

xxx

xxx

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Electrical safety

ESD safety
Environmental

guidelines.........................................................................

Power
Cabling
Protective

guidelines ...............................................................................

supplies........................................................................

................................................................................

earth .....................................................................

requirements ......................................................................

Contents

xxxi
xxxi
xxxi

1 — G-240W-B unit data sheet 1-1

1.1 G-240W-B part numbers and

1.2 G-240W-B general description

1.3 G-240W-B software and installation feature

1.4 G-240W-B interfaces and interface capacity
G-240W-B connections and

1.5 G-240W-B LEDs

1.6 G-240W-B detailed specifications

1.7 G-240W-B GEM ports and T-CONTs

1.8 G-240W-B performance monitoring

1.9 G-240W-B functional blocks

1.10 G-240W-B standards compliance
FCC

statement .......................................................................

FCC Radiation Exposure Statement

1.11 G-240W-B special
Wi-Fi service
G-240W-B ONT considerations and limitations

..........................................................................

considerations ....................................................

.........................................................................

identification .........................................

........................................................

support..............................

.......................................

components ..........................................

....................................................

...................................................

statistics.......................................

..........................................................

....................................................

..............................................

.................................

1-2
1-3

1-4

1-4

1-5
1-6

1-7
1-8
1-9

1-11
1-13
1-13
1-13
1-14
1-14
1-14

2 — Install a G-240W-B indoor ONT 2-1

2.1 Purpose

2.2 General

2.3

2.4 Recommended tools

2.5 Safety

2.6 Procedure

Prerequisites .............................................................................

...................................................................................

...................................................................................

....................................................................

information ......................................................................

................................................................................

2-2
2-2
2-2
2-2
2-3
2-4

3 — Replace a G-240W-B indoor ONT 3-1

3.1 Purpose

3.2 General

3.3

3.4 Recommended tools

3.5 Safety

3.6 Procedure

Prerequisites .............................................................................

...................................................................................

...................................................................................

....................................................................

information ......................................................................

................................................................................

3-2
3-2
3-2
3-2
3-3
3-4

4 — Configure a G-240W-B indoor ONT 4-1

4.1 General

4.2 HGU mode GUI

Alcatel-Lucent 7368 ISAM ONT xxxv
Edition 01
G-240W-B Product Guide

...................................................................................

configuration..........................................................

Login

...................................................................................

Procedure 4-1 Login to web-based GUI
Device and connection status
Procedure 4-2 Device information

......................................................

..........................................

retrieval.....................................

4-2
4-2

4-2
4-2
4-3
4-4

xxx
xxx

xxxi

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Contents

Procedure 4-3 LAN status
Procedure 4-4 WAN status
Procedure 4-5 WAN status IPv6 retrieval

retrieval ...............................................

retrieval ..............................................

........................................

Procedure 4-6 Home networking information retrieval ....................... 4-9

Procedure 4-7 Optics module status retrieval
Network
Procedure 4-8 LAN networking
Procedure 4-9 LAN IPv6 networking
Procedure 4-10 WAN networking

configuration..............................................................

configuration ..................................

configuration ............................

configuration................................

Procedure 4-11 WiFi 2.4G networking configuration
Procedure 4-12 WiFi 5G networking
Procedure 4-13 Routing configuration
Procedure 4-14 DNS

configuration ...............................................

Procedure 4-15 TR-069 configuration
Security
Procedure 4-16 Firewall

configuration ..............................................................

configuration ..........................................

configuration ............................

..........................................

...........................................

Procedure 4-17 MAC filter configuration
Procedure 4-18 IP filter configuration
Procedure 4-19 DMZ and ALG
Application

configuration ..........................................................

configuration....................................

..........................................

Procedure 4-20 Port forwarding configuration
Procedure 4-21 DDNS configuration
Procedure 4-22 NTP

configuration ...............................................

.............................................

Procedure 4-23 USB storage configuration
Maintenance

.........................................................................

Procedure 4-24 Password configuration
Procedure 4-25 SLID configuration
Procedure 4-26 Device

management ............................................

Procedure 4-27 Backup and restore
Procedure 4-28 Upgrade

firmware...............................................

Procedure 4-29 Reboot ONT

..............................................

.............................................

......................................................

Procedure 4-30 Restore factory defaults
Procedure 4-31 Diagnose
Procedure 4-32 View log files

4.3 SFU mode GUI configuration
Login

..................................................................................

Procedure 4-33 Login to web-based
Device and connection status

connections...........................................

....................................................

.........................................................

GUI ........................................

.....................................................

Procedure 4-34 Device information retrieval
Maintenance

.........................................................................

Procedure 4-35 Password configuration
Procedure 4-36 LOID
Procedure 4-37 SLID configuration

4.4 Operator
Procedure 4-38 Modify the operator ID using OLT

ID..............................................................................

configuration ..............................................

..............................................

.................................

.........................

.......................................

................................

.....................................

........................................

.......................................

..................................

........................................

............................

4-10
4-11
4-12
4-13
4-15
4-16
4-18
4-19
4-20
4-21
4-22
4-23
4-24
4-25
4-26
4-27
4-27
4-28
4-29
4-30
4-31
4-31
4-32
4-33
4-34
4-34
4-35
4-36
4-37
4-38
4-39
4-39
4-39
4-40
4-41
4-42
4-42
4-43
4-44
4-44
4-45

xxxvi Alcatel-Lucent 7368 ISAM ONT

Edition 01

G-240W-B Product Guide

4-5
4-6
4-8

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Contents

List of figures

Figure 1 PSE

Figure 2 Laser product label .......................................................................xiv

Figure 3 Laser classification
Figure 4 Laser warning labels
Figure 1 Products below MCV value label

Figure 2 Products above MCV value label ........................................................xix

Figure 3 Recycling/take back/disposal of product symbol ....................................xxi

Figure 1 Sample safety label on the ONT

Figure 2 Sample laser product label showing CDRH 21 CFR compliance ..................xxvii

Figure 3 Laser product label
Figure 4 Laser classification
Figure 5 Laser warning labels
Figure 6 Sample laser product safety label on the ONT
Figure 1-1 G-240W-B indoor ONT physical
Figure 1-2 G-240W-B indoor ONT
Figure 1-3 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and

Figure 1-4 G-240W-B ONT hardware

Figure 2-1 Wall mounting keyholes on G-240W-B indoor ONTs .............................. 2-4

Figure 2-2 G-240W-B indoor ONT connections (back
Figure 3-1 G-240W-B indoor ONT
Figure 4-1 Web login window
Figure 4-2 Device Information window
Figure 4-3 LAN status
Figure 4-4 WAN status
Figure 4-5 WAN status IPv6
Figure 4-6 Home networking information
Figure 4-7 Optics module status
Figure 4-8 LAN network
Figure 4-9 LAN IPv6 network window
Figure 4-10 WAN network
Figure 4-11 WiFi 2.4G network window
Figure 4-12 WiFi 5G network
Figure 4-13 Routing network
Figure 4-14 DNS network
Figure 4-15 TR-069 network
Figure 4-16 Firewall window
Figure 4-17 MAC filter
Figure 4-18 IP filter
Figure 4-19 DMZ and ALG
Figure 4-20 Port forwarding
Figure 4-21 DDNS
Figure 4-22 NTP window
Figure 4-23 USB storage
Figure 4-24 Password
Figure 4-25 SLID configuration
Figure 4-26 Device management window
Figure 4-27 Backup and Restore
Figure 4-28 Firmware upgrade

Alcatel-Lucent 7368 ISAM ONT xxxvii
Edition 01
G-240W-B Product Guide

certification ............................................................................

label

.................................................................xiv

......................................................................

......................................................

equipment..........................................

....................................................................

label ..............................................................

xxviii
xxviii

....................................................................

equipment.........................

connections .......................................

LEDs...........................................................

without RF video

................................................................

block .....................................................

1-11
1-12

view) ...................................

connections ..................................................

.....................................................................

..........................................................

window.....................................................................

window ....................................................................

window ..............................................................

window .............................................

window .......................................................

window .................................................................

...........................................................

window...............................................................

........................................................

window ...........................................................

window ...........................................................

window................................................................

window ............................................................

.....................................................................

window ...................................................................

window ......................................................................

window ...............................................................

window ............................................................

window.........................................................................

..........................................................................

window.................................................................

window ....................................................................

window .........................................................

......................................................

window .......................................................

window .........................................................

4-10
4-12
4-13
4-15
4-16
4-18
4-19
4-20
4-21
4-23
4-24
4-25
4-26
4-27
4-28
4-29
4-30
4-31
4-32
4-33
4-34
4-34

xi

xv

xviii

xxv

xxix

xxx
1-5
1-6

2-5
3-4
4-3
4-4
4-5
4-6
4-8
4-9

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Contents

Figure 4-29 Reboot window
Figure 4-30 Factory default window
Figure 4-31 Diagnose window
Figure 4-32 Log
Figure 4-33 Web login
Figure 4-34 Device Information
Figure 4-35 Password
Figure 4-36 LOID configuration window
Figure 4-37 SLID configuration

window ...........................................................................

......................................................................

............................................................

....................................................................

window ...................................................................

window ........................................................

window ....................................................................

........................................................

window .........................................................

4-35
4-36
4-37
4-38
4-40
4-41
4-42
4-43
4-44

List of tables

Table 1 Safety labels
Table 1 Safety labels
Table 1-1 Identification of G-240W-B indoor
Table 1-2 G-240W-B power supply

Table 1-3 G-240W-B indoor ONT interface connection capacity ............................. 1-5

Table 1-4 G-240W-B indoor ONT physical
Table 1-5 G-240W-B indoor ONT LEDs
Table 1-6 G-240W-B indoor ONT physical

Table 1-7 G-240W-B indoor ONT power consumption specifications ........................ 1-8

Table 1-8 G-240W-B indoor ONT environmental
Table 1-9 G-240W-B indoor ONT capacity for GEM ports and
Table 1-10 Package P ONTs ONTENET performance monitoring
Table 1-11 Package P ONTs ONTL2UNI performance monitoring statistics
Table 1-12 Package P ONTs PONONTTC, PONONTMCTC, PONONTTCHSI,

PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP performance
monitoring

Table 1-13 Package P ONTs PONONTTC aggregate performance monitoring

statistics ..........................................................................

Table 1-14 G-240W-B ONT considerations and limitations
Table 4-1 Device Information parameters
Table 4-2 LAN status
Table 4-3 WAN status
Table 4-4 WAN status IPv6
Table 4-5 Home networking
Table 4-6 Optics module status
Table 4-7 LAN network
Table 4-8 LAN IPv6 network
Table 4-9 WAN network
Table 4-10 WiFi 2.4G network parameters
Table 4-11 WiFi 5G network
Table 4-12 Routing network
Table 4-13 DNS network
Table 4-14 TR-069 network
Table 4-15 Firewall parameters
Table 4-16 MAC filter
Table 4-17 IP filter
Table 4-18 DMZ and ALG

xxxviii Alcatel-Lucent 7368 ISAM ONT

..................................................................................

..............................................................................

ONTs .............................................

................................................................

connections .........................................

............................................................

specifications.......................................

specifications...............................

T-CONTs......................

statistics

statistics ............................................................

...................................

.......................................................

parameters ..................................................................

parameters .................................................................

parameters ...........................................................

parameters .........................................................

parameters ....................................................

parameters ..............................................................

parameters ........................................................

parameters .............................................................

.....................................................

parameters ........................................................

parameters ........................................................

parameters.............................................................

parameters .........................................................

..................................................................

parameters ................................................................

parameters ...................................................................

parameters ............................................................

.................. 1-9

................

Edition 01

G-240W-B Product Guide

1-10

1-10

1-10
1-15

4-10
4-12
4-13
4-15
4-17
4-18
4-20
4-21
4-21
4-23
4-24
4-25
4-26

x

xxiv
1-2
1-3

1-5
1-7
1-8

1-8
1-8

4-4
4-5
4-7
4-8
4-9

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Contents

Table 4-19 Port forwarding
Table 4-20 DDNS

parameters......................................................................

Table 4-21 NTP parameters
Table 4-22 USB storage
Table 4-23 Password
Table 4-24 SLID configuration
Table 4-25 Device management parameters
Table 4-26 Device Information
Table 4-27 Password
Table 4-28 SLID configuration

parameters .........................................................

.......................................................................

parameters ..............................................................

parameters .................................................................

parameters ......................................................

...................................................

parameters .....................................................

parameters .................................................................

parameters ......................................................

4-27
4-28
4-29
4-30
4-32
4-32
4-33
4-41
4-42
4-44

Alcatel-Lucent 7368 ISAM ONT xxxix
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

1 — G-240W-B unit data

sheet

1.1 G-240W-B part numbers and identification 1-2

1.2 G-240W-B general description 1-3

1.3 G-240W-B software and installation feature support 1-4

1.4 G-240W-B interfaces and interface capacity 1-4

1.5 G-240W-B LEDs 1-6

1.6 G-240W-B detailed specifications 1-7

1.7 G-240W-B GEM ports and T-CONTs 1-8

1.8 G-240W-B performance monitoring statistics 1-9

1.9 G-240W-B functional blocks 1-11

1.10 G-240W-B standards compliance

1-13

Alcatel-Lucent 7368 ISAM ONT 1-1
Edition 01
G-240W-B Product Guide

1.11 G-240W-B special considerations

1-14

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Mnemonic

Ordering kit

part number

Provisioning
number

Description

CLEI

CPR

ECI/
Bar
code

G-240W-B

3FE 56636 AA

3FE 56756 BAAA

Package

P 2 POTS ports, 4 10/100/1000

Base-T Ethernet interfaces, and

802.11b/g/n/ac Wi-Fi radio with
on/off switch.

This ONT also has 2 USB ports, 1 USB

3.0 and 1 USB 2.0.
Includes 3-pin wall-mounted US AC/DC

adapter.

— — —

3FE 56636 BA

3FE 56756 AABA

Package

P 2 POTS ports, 4 10/100/1000

Base-T Ethernet interfaces, and

802.11b/g/n/ac Wi-Fi radio with
on/off switch.

This ONT also has 2 USB ports, 1 USB

3.0 and 1 USB 2.0.
Includes 2-pin wall-mounted European

(EU) AC/DC adapter.

— — —

3FE 56636 CA

3FE 56756 AABA

Package

P 2 POTS ports, 4 10/100/1000

Base-T Ethernet interfaces, and

802.11b/g/n/ac Wi-Fi radio with
on/off switch.

This ONT also has 2 USB ports, 1 USB

3.0 and 1 USB 2.0.
Includes 3-pin wall-mounted British

(UK) AC/DC adapter.

— — —

3FE 56636 CB
Customer-spe

cific

3FE 56756 ABBA

Package

P 2 POTS ports, 4 10/100/1000

Base-T Ethernet interfaces, and

802.11b/g/n/ac Wi-Fi radio with
on/off switch.

This ONT also has 2 USB ports, 1 USB

3.0 and 1 USB 2.0.
Includes 3-pin wall-mounted British

(UK) AC/DC adapter.

— — —

1 — G-240W-B unit data sheet

1.1 G-240W-B part numbers and identification

Table 1-1 provides part numbers and identification information for the G-240W-B
indoor ONT.

Table 1-1 Identification of G-240W-B indoor ONTs

Table 1-2 provides power supply ordering information about the G-240W-B ONT.
For more

1-2 Alcatel-Lucent 7368 ISAM ONT

UPS Guide.

information

on power supplies, see the 7368 ISAM ONT Power Supply and

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Power model

Power information

Customer category
or country
compliance tested
for

Notes

Mass Power

36 Watt AC/DC power adapter

ANSI municipality
United States,
Canada

1.2 G-240W-B general

G-240W-B indoor ONTs provide the subscriber interface for the network by
terminating the PON interface and converting it to user interfaces that directly
connect to subscriber devices. The ONT is compatible with all existing subscriber
equipment, including analog phones with both tone and rotary dial capabilities,
cordless phones, modems, fax machines, and caller ID boxes (Type I, Type II, and

Alcatel-Lucent 7368 ISAM ONT 1-3
Edition 01
G-240W-B Product Guide

Type III).
G-240W-B indoor ONTs provide the following functions:

• Single fiber GPON interface with 1.244Gbit/s upstream and 2.488Gbit/s

downstream data rates

• Advanced data features such as VLAN tag manipulation, classification, and

filtering.

• Traffic classification and QoS capability

• Analog Telephone Adapter (ATA) function integrated based on SIP (RFC3261)

and H.248, with various CLASS services supported, including Caller ID, Call
Waiting, Call Forwarding, and Call Transfer

• 5 REN per line

• Multiple voice Codec

• MDI/MDIX auto-negotiation

• Line Rate L2 traffic

• Internal Switch

• UPnP IGD1.0 support

• Bridged mode or routed mode per LAN port

• Optics that support received signal strength indication (RSSI)

• Internal DHCP server, with configurable DHCP pool and gateway

• WPS on wireless authorization support

• Configurable Wi-Fi tx power from 100mw to 500mw, in 100mw increments.

• Enhanced ONT; SSH-Telnet-FTP and http server are disabled from the WAN

side

• Concurrent 802.11n 3x3 MIMO in 2.4GHz and 802.11ac 4x4 MIMO in 5GHz

• 64/128 WEP encryption

• WPA, WPA-PSK/TKIP

• WPA2, WPA2-PSK/AES

Table 1-2 G-240W-B power supply

description

1 — G-240W-B unit data sheet

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

1 — G-240W-B unit data sheet

• support for multiple SSIDs (private and public instances); contact your ALU

representative for further

details.

• WLAN on/off push button

• WPS/PBC buttons (for 2.4G and 5G)

• Ethernet-based Point-to-Point (PPPoE)

• Network Address Translation (NAT)

• Network Address Port Translation (NAPT)

• ALG and UpnP port forwarding

• DMZ

• IP/MAC filter

• Multi-level firewall

• DNS server

• DHCP client/server

• support for HT40 mode for increased channel bandwidth

• support for up to 20 simultaneous wireless connections

• External USB HD (Hard Drive) support, accessible to all LAN devices

1.3 G-240W-B software and installation feature support

For information on installing or replacing the G-240W-B see:

• Install a G-240W-B indoor ONT

• Replace a G-240W-B indoor ONT

For information on the following topics, see the 7368 ISAM ONT Product Overview
Guide:

• ONT and MDU general descriptions of features and functions

• Ethernet interface specifications

• POTS interface specifications

• RSSI specifications

• Wi-Fi specifications

• ONT optical budget

• SLID entry via Ethernet port

• ONT management using an ONT interface

1.4 G-240W-B interfaces and interface capacity

Table 1-3 describes the supported interfaces and interface capacity for G-240W-B
indoor ONTs.

1-4 Alcatel-Lucent 7368 ISAM ONT

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ONT type
and model

Maximum capacity

POTS

10/
100
BASE-T

10/
100/
1000
BASE-T

RF video

(CATV)

MoCA

VDSL2

E1/T1

Local craft

GPON
SC/
APC

G-240W-B

(1)

2 — 4 — — — — — 1

Connection

(1)

Description

USB ports

This connection is provided through 2 USB ports, 1 USB 3.0 and 1 USB

2.0. The ONT supports external USB hard drives that can be made
accessible to all LAN devices.

Table 1-3 G-240W-B indoor ONT interface connection capacity

Note

(1)

The G-240W-B ONTs provide Wi-Fi service that is enabled and disabled using a Wi-Fi on/off switch.

G-240W-B connections and components

Figure 1-1 shows the physical connections for G-240W-B indoor ONTs,

Figure 1-1 G-240W-B indoor ONT physical connections

USB 3.0 USB 2.0 TEL1 T EL2 LAN1 LAN2 L AN3 LAN4 POWER ON/OFF UPS

USB

ports

POTS

ports (2)

(RJ-11)

Ethernet
ports (4)

(RJ-45)

Wi-Fi

security

buttons (2)

Reset

button

Table 1-4 describes the physical connections for G-240W-B indoor ONTs.

Table 1-4 G-240W-B indoor ONT physical connections

1 — G-240W-B unit data sheet

Wireless

On/Off
button

Power

input

On/Off

button

Fiber
optic

port

24614

(1 of 2)

Alcatel-Lucent 7368 ISAM ONT 1-5
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Connection

(1)

Description

POTS ports

This connection is provided through RJ-11 ports. Up to two POTS
connections are supported.The POTS ports support voice services.

Ethernet ports

This connection is provided through Ethernet RJ-45 connectors. Up to
four 10/100/1000 Base-T Ethernet interfaces are supported.The
Ethernet ports can support both data and in-band video services on all
four interfaces.

WPS buttons

The Wi-Fi Protected Setup buttons are labeled WPS2.4G and WPS5G.
These buttons enable and disable WLAN data encryption.

WLAN button

Wi-Fi service is compliant with IEEE 802.11 standards and is enabled
and disabled using the WLAN button.

Reset button

This button resets the ONT to the factory defaults.

Power input

This connection is provided through the power connector. A power
cable fitted with a barrel connector is used to make the connection.

On/Off button

This button turns the ONT on or off.

1 — G-240W-B unit data sheet

(2 of 2)

Note

(1)

The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the
power connector.

1.5 G-240W-B LEDs

Figure 1-2 shows the G-240W-B indoor ONT LEDs.

Figure 1-2 G-240W-B indoor ONT LEDs

LAN1

LINK AUTH

BTR

POWER

LAN2

POWER BT R LINK AUTH LAN1 LAN2 LAN3 LAN4 T EL1 TEL2 VOIP WPS WPS WLAN WLAN USB INTERN ET

1-6 Alcatel-Lucent 7368 ISAM ONT

Table 1-5 provides LED descriptions for G-240W-B indoor ONTs.

LAN3

LAN4

TEL1

TEL2

VOIP

WPS

2.4G

2.4G 5 G 2.4G 5G

WPS

5G

WLAN

2.4G

5G

USB

WLAN

INTERNET

Edition 01

G-240W-B Product Guide

24615

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Indicator

LED color and
behavior

LED behavior description

Power

Green solid
Red solid
Off

Power on
Light failed on startup (for example corrupt flash), or self test failed on startup,

or self test failed during regular operation or when executed over OMCI
Power off

BTR

Off
Green

Battery alarm set or battery not provisioned (not affected by AC power failure)
Battery charged; no battery alarms

Link

Green solid
Off

GPON link between ONT and OLT is operating normally
GPON link is down or no link connected

Auth

Green solid
Green flashing
Off

ONT is authorized
ONT is process of ranging or synchronizing on OMCI
ONT is not authorized

LAN 1 to 4

Green solid
Green flashing
Off

Ethernet is linked
LAN activity is present (in either direction)
ONT power is off or Ethernet is not connected

TEL 1 to 2

Green solid
Green flashing
Off

Off hook
Call in or talking
On hook

VOIP

Green solid
Off

VOIP service is OK
VOIP service is not OK

WPS

2.4G and 5G

Green solid
Green flashing
Off

Wireless LAN link is up
Wireless LAN link activity
Wireless LAN link is down or no link is connected

WLAN

2.4G and 5G

Green solid
Green flashing
Off

Wireless is enabled
There is traffic on wireless interface
Wireless is down or no link is connected

USB

Green solid
Green flashing
Off

At least one USB device is connected
There is traffic activity on at least on USB device
No USB device is connected

INTERNET

Green solid

Green flashing

Off

HSI WAN is connected: a) the device has an IP address assigned from IPCP, DHCP,
or static, and no traffic has been detected; b) the session is dropped due to idle
timeout but the PON link is still present.

PPPoE or DHCP connection in progress

HSI WAN is not connected: a) there is no physical interface connection; b) the
device is in bridged mode without an assigned IP address; c) the session has been
dropped for reasons other than idle timeout.

1 — G-240W-B unit data sheet

Table 1-5 G-240W-B indoor ONT LEDs

1.6 G-240W-B detailed specifications

Alcatel-Lucent 7368 ISAM ONT 1-7
Edition 01
G-240W-B Product Guide

Table 1-6 lists the physical specifications for G-240W-B indoor ONTs.

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Description

Specification

Length

11.8 in. (300 mm)

Width

7.3 in. (185 mm)

Height

1.4 in. (36 mm)

Weight [within ± 0.5 lb (0.23 kg)]

1.33 lb (0.61 kg)

Mnemonic

Maximum power
(Not to exceed)

Condition

Minimum power

Condition

G-240W-B
(3FE 56525
AAAA)

30 W

2 POTS off-hook, 4
10/100/1000 Base-T
Ethernet, Wi-Fi operational

12 W

2 POTS on-hook, other
interfaces/services not
provisioned

Mounting method

Temperature range and humidity

Altitude

On desk or wall
mounted

Operating: 23°F to 113°F (-5°C to 45°C)
ambient temperature

10% to 90% relative humidity, non-condensing

Contact your Alcatel-Lucent technical support
representative for more information

Storage: Contact your Alcatel-Lucent support
representative for more information

ONT or MDU

Maximum

Notes

Package P ONTs

GEM ports per indoor or
outdoor ONT

64

—

1 — G-240W-B unit data sheet

Table 1-7 lists the power consumption specifications for G-240W-B indoor ONT.

Table 1-7 G-240W-B indoor ONT power consumption specifications

Table 1-6 G-240W-B indoor ONT physical specifications

Table 1-8 lists the environmental specifications for G-240W-B indoor ONT.

Table 1-8 G-240W-B indoor ONT environmental specifications

1.7 G-240W-B GEM ports and T-CONTs

Table 1-9 lists the

maximum

number of

supported T-CONTs
appropriate release Customer Release Notes for the most accurate list of supported
devices.

Table 1-9 G-240W-B indoor ONT capacity for GEM ports and T-CONTs

and GEM ports. See the

(1 of 2)

1-8 Alcatel-Lucent 7368 ISAM ONT

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ONT or MDU

Maximum

Notes

T-CONTs

per

indoor

or outdoor

ONT

32

—

ONT

ONTENET statistics

FCSE

EC LC
RBO

SCF

MCF

DT
IMTE

CSE

AE
IMRE

FTL

TBO

SQE

G-240W-B

(1)

✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓

1 — G-240W-B unit data sheet

(2 of 2)

1.8 G-240W-B performance monitoring statistics

The following section identifies the supported performance monitoring statistics for
G-240W-B

ONTs. A check mark indicates the statistic is supported on that ONT. An
empty cell indicates the statistic is not supported. The following tables are
categorized by supported alarm types:

• Table 1-10 provides statistics for ONTENET type counters

• Table 1-11 provides statistics for ONTL2UNI type counters

• Table 1-12 provides statistics for PONONTTC, PONONTMCTC,

PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, and
PONONTTCVOIP type counters

• Table 1-13 provides statistics for PONONTTC aggregate type counters

Note — If you

monitoring statistics using TL1, please contact your Alcatel-Lucent
support representative for more information about how to access and
retrieve performance monitoring type counters.

de la performance G-240W-B ONT utilisant TL1, se il vous plaît
contacter votre représentant de support d'Alcatel-Lucent pour plus
d'informations sur la façon d'accéder et de récupérer des compteurs
de performance de type de surveillance.

have trouble accessing G-240W-B ONTs

Si vous avez des difficultés à accéder statistiques de suivi

Table 1-10 Package P ONTs ONTENET performance monitoring statistics

performance

Note

(1)

A 5 second polling window limitation exists on the ONT, therefore the margin of error for each
15-min window is 5 seconds

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

ONT

ONTL2UNI statistics

FRAMES

BYTES
MCFRAMES

DSDRPDFRMS

USDRPDFRMS

USFRAMES

DSFRAMES

USBYTES

DSBYTES
USMCFRAMES

DSMCFRAMES

G-240W-B

(

1)

✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓

ONT

PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES,
PONONTTCFLOW, PONONTTCVOIP statistics

TXBLOCKS

TXFRAGS

RXBLOCKS

RXFRAGS
LOSTFRAGS
BADGEMHDRS

G-240W-B

(1)

✓ ✓ ✓ ✓ ✓

ONT

PONONTTC (aggregate) statistics

TXBLOCKS

TXFRAGS

RXBLOCKS

RXFRAGS
LOSTFRAGS
BADGEMHDRS

G-240W-B

(1)

✓ ✓ ✓ ✓ ✓

1 — G-240W-B unit data sheet

Note

(1)

A 5 second polling window limitation exists on the ONT, therefore the margin of error for

15-min window is 5 seconds

Table 1-12 Package P ONTs PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES,

Table 1-11 Package P ONTs ONTL2UNI performance monitoring statistics

PONONTTCFLOW, PONONTTCVOIP performance monitoring statistics

each

Note

(1)

A 5 second polling window limitation exists on the ONT, therefore the margin of error for

15-min window is 5 seconds

Table 1-13 Package P ONTs PONONTTC aggregate performance monitoring statistics

Note

(1)

A 5 second polling window limitation exists on the ONT, therefore the margin of error for

1-10 Alcatel-Lucent 7368 ISAM ONT

15-min window is 5 seconds

each

each

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

1 — G-240W-B unit data sheet

1.9 G-240W-B functional blocks

G-240W-B indoor ONTs are single-residence ONTs that support Wireless (Wi-Fi)
service. Wi-Fi service on these ONTs is compliant with the IEEE 802.11 standard
and enabled or
ONTs transmit Ethernet packets to four RJ-45 Ethernet ports and voice traffic to two
RJ-11 POTS ports. These ONTs also feature fiber optic, USB, and power connectors.

Figure 1-3 shows the functional blocks for G-240W-B indoor ONT.

Figure 1-3 Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and without RF

2xRJ11 FXS

ONT SoC technology serves as the main hardware block for these ONTs; see
Figure 1-4.

Alcatel-Lucent 7368 ISAM ONT 1-11
Edition 01
G-240W-B Product Guide

GPON

NAND
DDR3

disabled

SLIC

using a WLAN button. In

video

PCIe

GPON SoC

GE

GE GE GE

XFMR

4xGE

mux

GE PHY

PCIe

RGMII

addition

to the Wi-Fi service, these

11n PA/LNA

converter

GE

11ac

RAM

ANT

USB3.0
USB2.0

3x3

2.4G

ANT

PA/LNA
4x4, 5G

24674

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

1 — G-240W-B unit data sheet

Figure 1-4 G-240W-B ONT hardware block

POTS ports

Control

processor

SoC

DSP

Bridge

SoC

Ethernet

MACs

GPON

MAC

Ethernet

ports GPON

19421

1-12 Alcatel-Lucent 7368 ISAM ONT

ONT SoC technology consists of five key elements:

• GPON MAC

The Gigabit Passive Optical Network Media Access Control (GPON MAC)
element

on the SoC

terminates

the GPON

interface

using an optical

diplexer.
interface supports GPON as described in G.984.3 (GPON TC Layer) ITU
specification.

• Ethernet MAC

The SoC provides up to four GE MACs.

• DSP interface

The Digital Signal Processor (DSP) provides voice processing for 2 POTS lines
with 3-way calling. The DSP has a dedicated 64 kbyte instruction cache and
shares a 32 kbyte data cache with the Control Processor. It provides up to 4
network processor cores, each at 800MHz.

• Control Processor

The Control Processor features an integral memory management unit that
supports a dedicated 64 kbyte instruction cache and shares a single 32 kbyte data
cache with the DSP. The

Control Processor

and DSP also include a single channel
Data Management Application (DMA) controller with a 4 kbyte read ahead
low-latency Dynamic Random Access Memory (DRAM) access port. The
processors typically run at 500 MHz.

• Switch matrix

The Switch matrix provides an integrated data channel between the four GE
MACs, the GPON MAC, the DSP, the control processor, and the other integrated
elements such as flash memory, DRAM, and the local bus controller.

These ONTs can also interact with additional hardware components to support
functionality not provided by the SoC technology.

Edition 01

G-240W-B Product Guide

This

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

1 — G-240W-B unit data sheet

1.10 G-240W-B standards compliance

Alcatel-Lucent 7368 ISAM ONT 1-13
Edition 01
G-240W-B Product Guide

G-240W-B indoor ONTs are compliant with the following standards:

• 802.1p marking and VLAN based pbit is supported

• G.711 support for FAX and modem connection

• G.984 support GPON interface (framing)

• G.984.2 support for Amd1, class B+

• G.984.3 support for activation and password functions

• G.984.3 support for AES with operator enable/disable on per port-ID level

• G.984.3 support for FEC in both upstream and downstream directions

• G.984.3 support for multicast using a single GEM Port-ID for all video traffic

• G984.4 and G.983.2 support for OMCI v1 and v2 interface for ONT management

and provisioning

FCC statement

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF Rules.
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to provide
a separation distance of at least 20 cm from all persons and must not be co-located
or operating in conjunction with any other antenna or transmitter. End-users and
installers must be provided with antenna installation instructions and consider
removing the no-collocation statement.

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

1 — G-240W-B unit data sheet

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:

1 this device may not cause harmful interference, and
2 this device must accept any interference received, including interference that

may cause undesired operation.

Caution — Any changes or modifications not expressly approved by

the party
operate the equipment.

approuvés par la partie responsable de la conformité pourraient
annuler l'autorité de l'utilisateur à utiliser l'équipement.

1.11 G-240W-B special

G-240W-B is a package P ONT.

Wi-Fi service

G-240W-B indoor ONTs feature Wi-Fi service as well as voice and data services.
Wi-Fi is a wireless networking technology that uses radio waves to provide wireless
HSI and network connections. This ONT complies with the IEEE 802.11 standards,
which the Wi-Fi Alliance defines as the basis for Wi-Fi technology.

Wi-Fi physical features

G-240W-B

indoor ONTs have the

Wi-Fi service:

• WLAN button for enabling and disabling Wi-Fi service

• two internal antennae

• two Wi-Fi Protected Setup (WPS) push buttons (one each for 2.4G and 5G) for

adding WPS-enabled wireless devices

Wi-Fi standards and certifications

The Wi-Fi service on G-240W-B indoor ONTs supports the following IEEE
standards and Wi-Fi Alliance certifications:

• compliant with IEEE 802.11 standards

• certified for IEEE 802.11b/g/n standards

• WPA support including WPA-PSK

• certified for WPA2-Personal and WPA2-Enterprise

Wi-Fi GUI features

G-240W-B indoor ONTs have HTML-based Wi-Fi configuration GUIs.

G-240W-B ONT considerations and limitations

responsible

for

compliance

could void the user's authority to

Les changements ou modifications non expressément

considerations

following physical features

that assist in providing

Table 1-14 lists the considerations and limitations for Package P G-240W-B ONTs.

1-14 Alcatel-Lucent 7368 ISAM ONT

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Considerations and limitations

Call History Data collection (ONTCALLHST) is supported, except for the following

parameters: RTP
packets (discarded), far-end RTCP and RTCP-XR participation, RTCP average and peak round trip
delay, MOS, average jitter, number of jitter-buffer over-runs and under runs.

Some voice features are configurable on a per ONT basis, including Call Waiting, Call Hold, 3-Way
Calling, and Call Transfer.

The following voice features / GSIP parameters are configurable on a per-Client/ per-ONT basis (not
per-Subscriber):

• Enable Caller ID and Enable Caller Name ID

• Digitmap and the associated Interdigit and Critical timers and Enter key parameters

• Warmline timer is enabled per subscriber, but the warmline timer value is configured per ONT

and must have a lower value than the Permanent time

• Miscellaneous timers: Permanent, Timed-release, Reanswer, Error-tone, and CW-alert timers

• Features / functions: Message waiting mode, WMWI refresh interval, DTMF volume level

• Service Codes for the following features: CCW, Call Hold and Warmline

The Molex interface is not operational.

Table 1-14 G-240W-B ONT considerations and limitations

Alcatel-Lucent 7368 ISAM ONT 1-15
Edition 01
G-240W-B Product Guide

1 — G-240W-B unit data sheet

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

2 — Install a G-240W-B indoor ONT

2.1 Purpose 2-2

2.2 General 2-2

2.3 Prerequisites 2-2

2.4 Recommended tools 2-2

2.5 Safety information 2-3

2.6 Procedure 2-4

Alcatel-Lucent 7368 ISAM ONT 2-1
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

2 — Install a G-240W-B indoor ONT

2.1 Purpose

This chapter provides the steps to install a G-240W-B indoor ONT.

2.2 General

The steps listed in this chapter describe mounting and cabling for G-240W-B indoor
ONTs.

2.3 Prerequisites

You need the following items before beginning the installation:

• all required cables

2.4 Recommended tools

2-2 Alcatel-Lucent 7368 ISAM ONT

You need the following tools for the installation:

• #2 Phillips screwdriver

• 1/4 in. (6 mm) flat blade screwdriver

• wire strippers

• fiber optic splicing tools

• RJ-45 cable plug crimp tool

• voltmeter or multimeter

• optical power meter

• drill and drill bits

• paper clip

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

2.5 Safety information

Read the following safety information before installing the unit.

Danger 1 — Hazardous electrical voltages and currents can cause

serious physical harm or death. Always use insulated tools and follow
proper safety precautions when connecting or disconnecting power
circuits.

Tensions et courants électriques dangereuses peuvent

causer des dommages ou la mort physique grave. Toujours utiliser
des outils isolés et suivre les précautions de sécurité adéquates pour
connecter ou déconnecter les circuits de puissance.

Danger 2 — Make sure all sources of power are turned off and have

no live voltages present on feed lines or terminals. Use a voltmeter to
measure for voltage before proceeding.
Assurez-vous que toutes les sources d'alimentation sont
éteints et ne ont pas de tensions vivants présents sur les lignes
d'alimentation ou de terminaux. Utilisez un voltmètre pour mesurer
la tension avant de procéder.

Danger 3 — Always contact the local utility company before

connecting the enclosure to the utilities.

Toujours contacter la compagnie d'électricité

locale avant de brancher l'enceinte pour les services publics.

Warning — This equipment is ESD sensitive. Proper ESD

protections should be used when removing the fiber access cover of
the indoor ONT.

Cet équipement est sensible ESD. Protections ESD

appropriées doivent être utilisées pour retirer le couvercle de l'ONT
à l'intérieur d'accès en fibre.

Caution — Keep indoor ONTs out of direct sunlight. Prolonged

exposure to direct sunlight can damage the unit.

Gardez ONT intérieur hors du soleil direct. Une

exposition prolongée aux rayons du soleil peut endommager
l'appareil.

Note 1 — Observe the local and national laws and regulations

that may be applicable to this installation.
Respecter les lois et réglementations locales et
nationales qui peuvent être applicables à cette installation.

Note 2 — Observe the following:

• The indoor ONT should be installed in accordance with the

applicable
practices take precedent when there is conflict between the local
standard and the NEC or CEC.

• The indoor ONT must be installed by qualified service personnel.

• Indoor ONTs must be installed with cables that are suitably rated

and listed for indoor use.

• See the

the temperature ranges for these ONTs.

2 — Install a G-240W-B indoor ONT

requirements

detailed specifications

of the NEC or CEC. Local

in the

G-240W-B

Respectez les consignes suivantes:

authorities

and

unit data sheet for

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

• L'ONT intérieure doit être installée en conformité avec les
exigences applicables de la NEC ou CEC. Les autorités et les
pratiques locales prennent précédent quand il ya conflit entre la
norme locale et le NEC ou CEC.

• L'ONT intérieure doit être installé par un personnel qualifié.

• ONT intérieure doit être installée avec des câbles qui sont

convenablement évalués et classés pour une utilisation intérieure.

• Voir les spécifications détaillées dans la fiche de données de
l'unité G-240W-B pour les plages de température pour ces ONT.

Alcatel-Lucent 7368 ISAM ONT 2-3
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

2 — Install a G-240W-B indoor ONT

2.6 Procedure

Use this procedure to install a G-240W-B indoor ONT.

1 Place the indoor ONT unit:

a On the flat surface, such as a desk; go to step 3.

Note — The G-240W-B cannot be stacked with another ONT or with

other equipment. The ONT mounting requirements are:

• allow a minimum 100 mm clearance above the top cover

• allow a minimum 50 mm clearance from the side vents

• do not place any heat source directly above the top cover or below

the bottom cover

avec d'autres équipements. Les exigences de montage ONT sont:

• Laisser un espace minimum de 100 mm au-dessus du capot
supérieur

• Laisser un espace minimum de 50 mm à partir des prises d'air

• Ne placez pas une source de chaleur directement au-dessus du

capot supérieur ou inférieur à la couverture inférieure

b On a wall, go to step 2.

2 Mount the G-240W-B indoor ONT on a wall.

i The G-240W-B indoor ONT can be mounted in either a horizontal or vertical

position, as shown in Figure 2-1. If possible, mount the ONT on a wall stud.

Figure 2-1 Wall mounting keyholes on G-240W-B indoor ONTs

Keyholes for

vertical

mounting

ii Mark the wall with the location of the mounting holes. These holes should be

the same distance apart as the distance between the centers of the keyholes
on the ONT.

iii Drill the two holes in the wall where the ONT will be mounted and then drive

the mounting screws into the holes.

The recommended length of mounting screw is 1.15 in. (3.8 cm).

Le G-240W-B ne peut être empilé avec un autre ONT ou

latérales

Keyholes for horizontal mounting

RESET

24111

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

2 — Install a G-240W-B indoor ONT

Do not drive the screw into the wall

completely.

Leave

approximately

1/8 in.

(6 mm) between the screw head and the wall surface.

iv Slide the wall mount keyholes on the ONT enclosure or fiber storage tray

down over the mounting screws until the ONT is securely seated.

3 Review the connection locations as shown in Figures 2-2.

Figure 2-2 G-240W-B indoor ONT connections (back view)

Wireless

On/Off

USB 3.0 USB 2.0 TEL1 T EL2 LAN1 L AN2 LAN3 L AN4 POWER ON/OFF UPS

USB

ports

POTS

ports (2)

(RJ-11)

Ethernet
ports (4)

(RJ-45)

Wi-Fi

security

buttons (2)

Reset

button

Power

input

On/Off

button

4 Connect the Ethernet cables to the RJ-45 ports; see Figure 2-2 for the location of

the RJ-45 ports.

5 Route the POTS cables directly to the RJ-11 ports as per local practices.

The POTS port to the left is labeled 1 for Line 1 while the port on the right is
labeled 2 for Line 2, as shown in Figure 2-2.

6

Connect
Figure 2-2 for the location of the SC/APC connector.

the fiber optic cable with SC/APC

adapter

into the

SC/APC connector;

Danger — Fiber cables transmit invisible laser light. To avoid eye

damage or blindness, never look directly into fibers, connectors, or
adapters.

Câbles de fibres transmettent la lumière laser invisible.

Pour éviter des lésions oculaires ou la cécité, ne jamais regarder
directement dans les fibres, les connecteurs ou adaptateurs.

Warning — Be careful to maintain a bend radius of no less than 1.5 in.

(3.8 cm) when connecting the fiber optic cable. Too small of a bend
radius in the cable can result in damage to the optic fiber.

Veillez à maintenir un rayon de courbure d'au moins 1,5

po. (3,8 cm) lors de la connexion du câble de fibre optique. Trop petit
d'un rayon de courbure dans le câble peut entraîner des dommages à
la fibre optique.

button

Fiber
optic

port

24614

see

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

2 — Install a G-240W-B indoor ONT

Note — Fiber cable preparation varies depending on the type and size

of the inside or outside plant fiber cable being spliced to the SC/APC
fiber optic pigtail cable.

Préparation du câble de fibres varie en fonction du type et de
la taille de l'intérieur ou de câble de fibres de plante extérieur étant
assemblés bord à bord pour la SC/APC câble en queue de cochon à
fibres optiques.

7 Install the power supply according to manufacturer specifications.

Note — Observe the

• Units must be powered by a Listed or CE approved and marked

limited power source power supply with a minimum output rate of

12 V dc, 1.25

• Les unités doivent être alimentés par une alimentation de source
d'alimentation limitée répertoriés ou homologués CE et sont
marqués d'un taux de sortie minimum de 12 V cc, 1,25 A

8 Connect the power cable to the power connector.

9 Power up the ONT unit by using the power switch.

10 If used, enable the Wi-Fi service.

i Locate the WLAN button on the ONT; see Figure 2-2 for location of the WLAN

button.

ii Press the WLAN button to change the status of the Wi-Fi service.

11 Verify the ONT LEDs, voltage status, and optical signal levels; see the 7368

Hardware and Cabling Installation Guide.

12 Activate and test the services; see the 7368 Hardware and Cabling Installation

Guide.

13 If used, configure the SLID; see the 7368 ISAM ONT Configuration, Management,

and Troubleshooting Guide.

14 If necessary, reset the ONT.

i Locate the Reset button on a G-240W-B indoor ONT as shown in Figure 2-2.

ii Insert the end of a straightened paper clip or other narrow object into the

hole in the Reset button to reset the ONT.

15 STOP. This procedure is complete.

following:

A.

Respectez les onsignes

suivantes:

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

3 — Replace a G-240W-B indoor ONT

3.1 Purpose 3-2

3.2 General 3-2

3.3 Prerequisites 3-2

3.4 Recommended tools 3-2

3.5 Safety information 3-3

3.6 Procedure 3-4

Alcatel-Lucent 7368 ISAM ONT 3-1
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

3 — Replace a G-240W-B indoor ONT

3.1 Purpose

This chapter provides the steps to replace G-240W-B indoor ONTs.

3.2 General

The steps listed in this chapter describe mounting and cabling for G-240W-B indoor
ONTs.

3.3 Prerequisites

You need the following items before beginning the installation:

• all required cables

3.4 Recommended tools

3-2 Alcatel-Lucent 7368 ISAM ONT

You need the following tools for replacing the ONT:

• #2 Phillips screwdriver

• 1/4 in. (6 mm) flat blade screwdriver

• wire strippers

• fiber optic splicing tools

• RJ-45 cable plug crimp tool

• voltmeter or multimeter

• optical power meter

• drill and drill bits

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

3.5 Safety information

Read the following safety information before replacing the unit.

Danger 1 — Hazardous electrical voltages and currents can cause

serious physical harm or death. Always use insulated tools and follow
proper safety precautions when connecting or disconnecting power
circuits.
Tensions et courants électriques dangereuses peuvent
causer des dommages ou la mort physique grave. Toujours utiliser
des outils isolés et suivre les précautions de sécurité adéquates pour
connecter ou déconnecter les circuits de puissance.

Danger 2 — Make sure all sources of power are turned off and have

no live voltages present on feed lines or terminals. Use a voltmeter to
measure for voltage before proceeding.

sont éteints et ne ont pas de tensions vivants présents sur les lignes
d'alimentation ou de terminaux. Utilisez un voltmètre pour mesurer
la tension avant de procéder.

Danger 3 — Always contact the local utility company before

connecting the enclosure to the utilities.
locale avant de brancher l'enceinte pour les services publics.

Warning — This equipment is ESD sensitive. Proper ESD

protections should be used when removing the fiber access cover of
the indoor ONT.

appropriées doivent être utilisées pour retirer le couvercle de l'ONT
à l'intérieur d'accès en fibre

Caution — Keep indoor ONTs out of direct sunlight. Prolonged

exposure to direct sunlight can damage the unit.
exposition prolongée aux rayons du soleil peut endommager

l'appareil.

Note 1 — Observe the local and national laws and regulations

that may be applicable to this installation.
Respecter les lois et réglementations locales et
nationales qui peuvent être applicables à cette installation

Note 2 — Observe the following:

• The indoor ONT should be installed in accordance with the

applicable
practices take precedent when there is conflict between the local
standard and the NEC or CEC.

• The indoor ONT must be installed by qualified service personnel.

• Indoor ONTs must be installed with cables that are suitably rated

and listed for indoor use.

• See the

the ONT temperature ranges for these ONTs.

3 — Replace a G-240W-B indoor ONT

Assurez-vous que toutes les sources d'alimentation

Toujours contacter la compagnie d'électricité

Cet équipement est sensible ESD. Protections ESD

Gardez ONT intérieur hors du soleil direct. Une

requirements

detailed specifications

of the NEC or CEC. Local

in the

G-240W-B

unit data sheet for

authorities

Respectez les consignes suivantes:

and

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

• L'ONT intérieure doit être installée en conformité avec les
exigences applicables de la NEC ou CEC. Les autorités et les
pratiques locales prennent précédent quand il ya conflit entre la
norme locale et le NEC ou CEC.

• L'ONT intérieure doit être installé par un personnel qualifié.

• ONT intérieure doit être installée avec des câbles qui sont

convenablement évalués et classés pour une utilisation intérieure.

• Voir les spécifications détaillées dans la fiche de données de
l'unité G-240W-B pour les plages de température pour ces ONT
ONT.

Alcatel-Lucent 7368 ISAM ONT 3-3
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

3 — Replace a G-240W-B indoor ONT

3.6 Procedure

Use this procedure to replace a G-240W-B indoor ONT.

1 Deactivate the ONT services at the P-OLT.

If you are using the SLID feature, this step is not required. The ONT and the
services can remain in service (IS).

i Use the RTRV-ONT command to verify the ONT status and th associated

services. Record the serial number or the SLID of the ONT displayed in the
command output.

Example:

2 If used, disable the Wi-Fi service by pressing the WLAN button; see Figure 3-1 for

3 Power down the unit by using the on/off power switch.

4

3-4 Alcatel-Lucent 7368 ISAM ONT

RTRV-ONT::ONT-1-1-1-1-1;

ii If the ONT is in service, place the ONT in OOS state.

Example:

ED-ONT::ONT-1-1-1-1-1;

the location of the WLAN button.

Figure 3-1 G-240W-B indoor ONT connections

USB 3.0 USB 2.0 TEL1 T EL2 LAN1 LAN2 L AN3 LAN4 POWER ON/O FF UPS

Disconnect

USB

ports

POTS

ports (2)

(RJ-11)

the POTS,

Ethernet
ports (4)

(RJ-45)

Ethernet,

Reset

button

Wi-Fi

security

buttons (2)

Power

input

and power cables from the ONT; see Figure 3-1 for

the connector locations on the G-240W-B indoor ONT.

Wireless

On/Off
button

On/Off

button

Fiber
optic

port

24614

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

3 — Replace a G-240W-B indoor ONT

5 Disconnect the fiber optic cables.

Danger — Fiber cables transmit invisible laser light. To avoid eye

damage or blindness, never look directly into fibers, connectors, or
adapters.

Câbles de fibres transmettent la lumière laser invisible.
Pour éviter des lésions oculaires ou la cécité, ne jamais regarder
directement dans les fibres, connecteurs ou adaptateurs

i Unplug the fiber optic cable with SC/APC connector from the ONT; see

Figure 3-1 for the location of the fiber optic port.

ii Attach a fiber dust cover to the end of the SC/APC connector.

6 Replace the ONT with a new unit:

a On a flat surface, such as a desk, substitute the new ONT for the old ONT on

a flat surface, horizontally resting on its four feet.

b On a wall.

i Slide the old ONT off of the mounting screws until the ONT is free of the

wall.

ii Slide the wall mount holes on the ONT enclosure over the mounting

screws until it is securely seated.

7 Connect the Ethernet cables directly to the RJ-45 ports; see Figure 3-1 for the

location of the RJ-45 ports.

8 Connect the POTS cables directly to the RJ-11 ports as per local practices; see

Figure 3-1 for the location of the RJ-11 ports.

The RJ-11 port to the left is labeled 1 for Line 1 while the port on the right is
labeled 2 for Line 2.

9 If required, have approved service personnel who are trained to work with optic

fiber clean the fiber optic connection. See the 7368 ISAM ONT Configuration,
Management, and Troubleshooting Guide for more information about fiber optic
handling, inspection, and cleaning.

Danger — Fiber optic cables transmit invisible laser light. To avoid eye

damage or blindness, never look directly into fibers, connectors, or
adapters.

Câbles de fibre optique transmettent la lumière laser
invisible. Pour éviter des lésions oculaires ou la cécité, ne jamais
regarder directement dans les fibres, les connecteurs ou adaptateurs.

10 Connect the fiber optic cable with SC/APC adapter into the SC/APC connector.

Figure 3-1shows the location of the SC/APC connector.

Danger — Fiber cables transmit invisible laser light. To avoid eye

damage or blindness, never look directly into fibers, connectors, or
adapters.

Câbles de fibre optique transmettent la lumière laser
invisible. Pour éviter des lésions oculaires ou la cécité, ne jamais
regarder directement dans les fibres, les connecteurs ou adaptateurs.

Warning — Be careful to maintain a bend radius of no less than 1.5 in.

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

(3.8 cm) when connecting the fiber optic cable. Too small of a bend
radius in the cable can result in damage to the optic fiber.

Veillez à maintenir un rayon de courbure d'au moins 1,5
po. (3,8 cm) lors de la connexion du câble de fibre optique. Trop petit
d'un rayon de courbure dans le câble peut entraîner des dommages à
la fibre optique.

Alcatel-Lucent 7368 ISAM ONT 3-5
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

3 — Replace a G-240W-B indoor ONT

11 Install the power supply according to manufacturer specifications.

12 Connect the power cable to the power connector.

13 Power up the unit by using the power switch.

14 If used, enable the Wi-Fi service by pressing the WLAN button; see Figure 3-1 for

the location of the WLAN button.

15 If used, configure the SLID; see the 7368 ISAM ONT Configuration, Management,

and Troubleshooting Guide for more information.

16 Verify the ONT LEDs, voltage status, and optical signal levels; see the 7368

Hardware and Cabling Installation Guide.

17 Activate and test the services; see the 7368 Hardware and Cabling Installation

Guide.

18 If necessary, reset the ONT.

i Locate the Reset button on a G-240W-B indoor ONT as shown in Figure 3-1.

ii Insert the end of a straightened paper clip or other narrow object into the

hole in the Reset button to reset the ONT.

19 STOP. This procedure is complete.

Note — Fiber cable preparation varies depending on the type and size

of the inside or outside plant fiber cable being spliced to the SC/APC
fiber optic pigtail cable.

Préparation du câble de fibres varie en fonction du type et
de la taille de l'intérieur ou de câble de fibres de plante extérieur
étant assemblés bord à bord pour la SC/APC câble en queue de cochon
à fibres optiques.

Note — Observe the

following:

• Units must be powered by a Listed or CE approved and marked

limited power source power supply with a minimum output rate of
12 V dc, 1.25 A.

Respectez les consignes suivantes:

• Les unités doivent être alimentés par une alimentation de

source d'alimentation limitée répertoriés ou homologués
CE et sont marqués d'un taux de sortie minimum de 12 V
cc, 1,25 A.

Note — A new SLID or the old SLID may be used with the replacement

ONT. If a new SLID is used, the new SLID must also be programmed at
the P-OLT using TL1 or a network manager. If the old SLID is used, no
changes need to be made at the P-OLT; see the operations and
maintenance documentation for the OLT for more details.

Une nouvelle EDTR ou le vieux EDTR peut être utilisé avec
l'ONT de remplacement. Si une nouvelle EDTR est utilisé, le nouveau
EDTR doit également être programmé à la classe P-OLT utilisant TL1
un gestionnaire de réseau. Si l'ancien EDTR est utilisé, aucune
modification ne est à apporter à la classe P-OLT; voir les opérations et
la documentation de maintenance pour le BTA pour plus de détails.

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

4 — Configure a G-240W-B indoor

ONT

4.1 General 4-2

4.2 HGU mode GUI configuration 4-2

4.3 SFU mode GUI configuration 4-39

4.4 Operator ID 4-44

Alcatel-Lucent 7368 ISAM ONT 4-1
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

4 — Configure a G-240W-B indoor ONT

4.1 General

Please refer to the configuration information provided with your OLT for the
software configuration procedure for a G-240W-B ONT.

For HTTP configuration procedures, please refer to the 7368 ISAM ONT
Configuration, Management, and Troubleshooting Guide.

4.2 HGU mode GUI configuration

Use the procedures below to use the web-based GUI for the G-240W-B in HGU
mode. This mode is preset at delivery.

A home gateway unit (HGU) is a home networking device, used as a gateway to
connect devices in the home through fiber to the Internet. An HGU
of features for the home network including routing and firewall capability. By using
the HGU, users can connect all smart equipment in their home, including personal
computers,

set-top boxes, mobile phones, and other consumer electronics devices, to

the Internet.

Login

provides

a variety

Use the procedure below to login to the web-based GUI for the G-240W-B.

Procedure 4-1 Login to web-based GUI

1 Open a web browser and enter the IP address of the ONT in the address bar.

The login window appears.

The default gateway IP address is http://192.168.1.1. You can connect to this IP
address using your web browser after connecting your PC to one of Ethernet ports
of the ONT. The static IP address of your PC must be in the same subnet as the
ONT.

2 Enter your username and password in the Log in window, as shown in Figure 4-1.

The default username and password are printed on the ONT. The default user
name is userAdmin. The default superuser name is adminGPON. Contact

4-2 Alcatel-Lucent 7368 ISAM ONT

Alcatel-Lucent for the superuser password.

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Caution — If you reset the router to recover the default username and

password,
their factory default values.

d'utilisateur et mot de passe par défaut, tous les autres paramètres de
configuration du routeur seront aussi restaurés à leurs valeurs par
défaut d'usine.

Note — If you forget the current username and password, press the

reset button for 5 s and the default values for the username and
password will be recovered at startup.

appuyez sur le bouton de réinitialisation pendant 5 s et les valeurs
par défaut pour le nom d'utilisateur et mot de passe seront

3 Click Login.

4 STOP. This procedure is complete.

Device and connection status

G-240W-B ONTs support the retrieval of a variety of device and connection
information, including:

• device information

• LAN status

• WAN status

• WAN status IPv6

• Home networking information

• Optics module status

récupérés au démarrage.

4 — Configure a G-240W-B indoor ONT

Figure 4-1 Web login window

all other router

Si vous réinitialisez le routeur pour récupérer le nom

Si vous oubliez le nom d'utilisateur et mot de passe actuel,

configuration

settings will also be restored to

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Device Name

Name on the ONT

Vendor

Name of the vendor

Serial Number

Serial number of the ONT

Hardware version

Hardware version of the ONT

Boot version

Boot version of the ONT

Software version

Software version of the ONT

Chipset

Chipset of the ONT

Device Running
Time

Amount of time the device has run since last reset in hours, minutes, and
seconds

4 — Configure a G-240W-B indoor ONT

Procedure 4-2 Device information retrieval

1 Select Status > Device Information from the top-level menu in the GPON Home

Gateway window, as shown in Figure 4-2.

Figure 4-2 Device Information window

Table 4-1 describes the fields in the Device Information window.

2 Click Refresh to update the displayed information.

4-4 Alcatel-Lucent 7368 ISAM ONT

3 STOP. This procedure is complete.

Table 4-1 Device Information parameters

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Wireless Information

Wireless Status

Indicates whether the wireless is on or off

Wireless Channel

Wireless channel number

SSID Name

Name of each SSID

Wireless
Encryption Status

Encryption type used on the wireless connection

Wireless Rx
Packets

Number of packets received on the wireless connection

Wireless Tx
Packets

Number of packets transmitted on the wireless connection
Wireless Rx Bytes

Number of bytes received on the wireless connection

Wireless Tx Bytes

Number of bytes transmitted on the wireless connection

Power
Transmission (mW)

Power of the wireless transmission, in mW
Ethernet Information

Ethernet Status

Indicates whether the Ethernet connection is on or off

Ethernet IP
Address

IP address of the Ethernet connection

4 — Configure a G-240W-B indoor ONT

Procedure 4-3 LAN status retrieval

1 Select Status > LAN Status from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-3.

Figure 4-3 LAN status window

Table 4-2 describes the fields in the LAN status window.

Table 4-2 LAN status parameters

(1 of 2)

Alcatel-Lucent 7368 ISAM ONT 4-5
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Ethernet Subnet
Mask

Subnet Mask of the Ethernet connection

Ethernet MAC
Address

MAC address of the Ethernet connection

Ethernet Rx
Packets

Number of packets received on the Ethernet connection

Ethernet Tx
Packets

Number of packets transmitted on the Ethernet connection
Ethernet Rx Bytes

Number of bytes received on the Ethernet connection

Ethernet Tx Bytes

Number of bytes transmitted on the Ethernet connection

4 — Configure a G-240W-B indoor ONT

(2 of 2)

2 Click Refresh to update the displayed information.

3 STOP. This procedure is complete.

Procedure 4-4 WAN status retrieval

1 Select Status > WAN Status from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-4.

Figure 4-4 WAN status window

Table 4-3 describes the fields in the WAN status window.

4-6 Alcatel-Lucent 7368 ISAM ONT

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

WAN connection
list

Drop-down menu listing all WAN connections. The connection shown is the
connection for which WAN status will be shown.

Connection Mode

Connection mode of the WAN connection

Enable/Disable

Select this checkbox to enable the WAN connection

VLAN

VLAN ID

WAN Link Status

Whether the WAN link is up or down

Pon Link Status

Whether the PON link is up or down

Tx Packets

Number of packets transmitted on the WAN connection

Rx Packets

Number of packets received on the WAN connection

Tx Dropped

Number of packets dropped on the transmit WAN connection

Rx Dropped

Number of packets dropped on the receive WAN connection

Err Packets

Number of errored packets on the WAN connection

2 Click Refresh to update the displayed information.

Alcatel-Lucent 7368 ISAM ONT 4-7
Edition 01
G-240W-B Product Guide

3 STOP. This procedure is complete.

4 — Configure a G-240W-B indoor ONT

Table 4-3 WAN status parameters

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

WAN connection
list

Drop-down menu listing all WAN connections. The connection shown is the
connection for which WAN status will be shown.

Connection Mode

Connection mode of the WAN connection

Enable/Disable

Select this checkbox to enable the WAN connection

VLAN

VLAN ID

WAN Link Status

Whether the WAN link is up or down

IPv6 Address

IPv6 address that identifies the device and its location

Netmask

Network mask

Gateway

Gateway address

Primary DNS

Primary Domain Name Server

Second DNS

Secondary Domain Name Server

Pon Link Status

Whether the PON link is up or down

4 — Configure a G-240W-B indoor ONT

Procedure 4-5 WAN status IPv6 retrieval

1 Select Status > WAN Status IPv6 from the top-level menu in the GPON Home

Gateway window, as shown in Figure 4-5.

Figure 4-5 WAN status IPv6 window

Table 4-4 describes the fields in the WAN status IPv6 window.

4-8 Alcatel-Lucent 7368 ISAM ONT

(1 of 2)

Table 4-4 WAN status IPv6 parameters

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Tx Packets

Number of packets transmitted on the WAN connection

Rx Packets

Number of packets received on the WAN connection

Tx Dropped

Number of packets dropped on the transmit WAN connection

Rx Dropped

Number of packets dropped on the receive WAN connection

Err Packets

Number of errored packets on the WAN connection

Field

Description

Local Interface

Ethernet

Table displays the number of Ethernet connections and their settings

Wireless

Table displays the number of wireless connections and their settings

Wireless Settings

4 — Configure a G-240W-B indoor ONT

(2 of 2)

2 Click Refresh to update the displayed information.

3 STOP. This procedure is complete.

Procedure 4-6 Home networking information retrieval

1 Select Status > Home Networking from the top-level menu in the GPON Home

Gateway window, as shown in Figure 4-6.

Figure 4-6 Home networking information window

Table 4-5 describes the fields in the Home networking window.

(1 of 2)

Alcatel-Lucent 7368 ISAM ONT 4-9
Edition 01
G-240W-B Product Guide

Table 4-5 Home networking parameters

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Network Name

Name of the wireless network

Access Point

Hexadecimal address of the wireless access point

Local Devices

Table entry

Each entry indicates the connection type, device name, IP address, hardware
address, and IP address allocation of each connected local device.

Field

Description

Laser Bias Current (ONT ANI-ONT-Side Optical
Measurements)

Laser bias current, measured in uA

Optics Module Voltage (ONT ANI-ONT-Side Optical
Measurements)

Optics module voltage, measured in V

4 — Configure a G-240W-B indoor ONT

(2 of 2)

2 Click Delete to delete a particular local device connection.

3 Click Refresh to update the displayed information.

4 STOP. This procedure is complete.

Procedure 4-7 Optics module status retrieval

1 Select Status > Optics Module Status from the top-level menu in the GPON

Gateway window, as shown in Figure 4-7.

Figure 4-7 Optics module status window

Home

Table 4-6 describes the fields in the Optics module status window.

Table 4-6 Optics module status parameters

(1 of 2)

4-10 Alcatel-Lucent 7368 ISAM ONT

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Optics Module Temperature (ONT ANI-ONT-Side
Optical Measurements)

Optics module temperature, measured in
C

Rx Optics Signal Level at 1490 nm (ONT ANI-ONT-Side
Optical Measurements)

Received optics signal level at 1490 nm,
measured in dBm

Tx Optics Signal Level at 1310 nm (ONT ANI-ONT-Side
Optical Measurements)

Transmitted optics signal level

at

1310

nm,

measured in dBm

Lower (ONT ANI-ONT-Side Optical
Measurements-Optical Threshold)

Lower optical threshold, measured in dBm

Upper (ONT ANI-ONT-Side Optical
Measurements-Optical Threshold)

Lower optical threshold, measured in dBm

4 — Configure a G-240W-B indoor ONT

(2 of 2)

2 Click Refresh to update the displayed information.

3 STOP. This procedure is complete.

Network configuration

• LAN

• LAN IPv6

• WAN

• WiFi 2.4G

• WiFi 5G

• Routing

• DNS

G-240W-B ONTs also support network configuration, including:

• TR-069

Alcatel-Lucent 7368 ISAM ONT 4-11
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Port Mode:
All Port to L2 Mode

Select this checkbox to set all ports to L2 mode

Port Mode
Port 1 - 4

Drop-down port mode for each port: Route mode or bridge mode
IPv4 Address

IP Address of the ONT

Subnet Mask

Subnet mask of the ONT

DHCP enable

Select this checkbox to enable DHCP

DHCP Start IP
Address

Starting DHCP IP address

DHCP End IP
Address

Ending DHCP IP address
DHCP Lease Time

DHCP lease time (in min)

Bind MAC Address

MAC address to associate to the LAN

Bind IP Address

IP address to associate to the bound MAC address

4 — Configure a G-240W-B indoor ONT

Procedure 4-8 LAN networking configuration

1 Select Network > LAN from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-8.

Figure 4-8 LAN network window

Table 4-7 describes the fields in the LAN network window.

2 Select the mode for each port.

3 Click Save.

4-12 Alcatel-Lucent 7368 ISAM ONT

4 Enter the DHCP configuration information.

Table 4-7 LAN network parameters

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

DNS Server

Choose a DNS server from the drop-down menu.

prefix config

Choose a prefix config option from the drop-down menu, either
WAN Conn ection

(prefix will be obtained from the WAN) or Static (enables you

to enter the prefix).

prefix

This field appears if you selected the “Static” option for the “prefix config”
field. Type a connection.

Interface

This field appears if you selected the Wan Connection option for the “prefix
config” field. Choose a WAN connection interface from the drop-down menu.

4 — Configure a G-240W-B indoor ONT

5 Click Save.

6 Bind a MAC address to the LAN by entering the MAC and IP addresses and then

clicking Add. Repeat for all MAC addresses to be bound.

7 STOP. This procedure is complete.

Procedure 4-9 LAN IPv6 networking configuration

1 Select Network > LAN_IPv6 from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-9.

Figure 4-9 LAN IPv6 network window

Table 4-8 describes the fields in the LAN IPv6 network window.

Table 4-8 LAN IPv6 network parameters

Alcatel-Lucent 7368 ISAM ONT 4-13
Edition 01
G-240W-B Product Guide

(1 of 2)

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

DHCPv6 Server
Enable

Select this checkbox to enable DHCP IPv6 server.

DHCP Start IP
Address

Enter the starting DHCP IP address.

DHCP End IP
Address

Enter the ending DHCP IP address.

Whether the
address info
through DCHP

Select this checkbox to enable address information retrieval through DHCP.

Whether other

info
obtained through
DHCP

Select this checkbox to enable retrieval of other information through DHCP.

Maximum interval
for periodic RA
messages

Enter the maximum interval (in seconds) for periodic Router Advertisement
messages. The interval range is from 4 to 1800.

Minimum interval
for periodic RA
messages

Enter the minimum interval (in seconds) for periodic Router Advertisement
messages. The interval range is from 4 to 1800.

4 — Configure a G-240W-B indoor ONT

4-14 Alcatel-Lucent 7368 ISAM ONT

(2 of 2)

2 Choose a DNS server, prefix config, and interface.

3 Select or enter the DHCP configuration information.

4 Enter the maximum and minimum intervals for RA messages.

5 Click Save/Apply.

6 STOP. This procedure is complete.

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

WAN Connection
List

Choose a WAN connection from the drop-down menu to set the connection
parameters

Connection Type

Select a connection type: IPoE or PPPoE

IP Mode

Choose an IP mode from the drop-down menu: IPv4 or IPv6

Enable/Disable

Select this checkbox to enable the WAN connection

NAT

Select this checkbox to enable NAT

Service

Select the checkboxes to enable service types for this connection

Enable VLAN

Select this checkbox to enable VLAN

VLAN ID

Enter the VLAN ID

VLAN PRI

Enter the VLAN PRI

WAN IP Mode

Choose an IP mode from the drop-down menu

4 — Configure a G-240W-B indoor ONT

Procedure 4-10 WAN networking configuration

1 Select Network > WAN from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-10.

Figure 4-10 WAN network window

Table 4-9 describes the fields in the WAN network window.

Alcatel-Lucent 7368 ISAM ONT 4-15
Edition 01
G-240W-B Product Guide

(1 of 2)

Table 4-9 WAN network parameters

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Connection Type

Choose a connection type from the drop-down menu

Username

Enter the username

Password

Enter the password

Keep Alive Time

Enter the Keep Alive Time (from 5 to 60 seconds)

4 — Configure a G-240W-B indoor ONT

(2 of 2)

2 Configure a specific WAN connection.

3 Click Save.

4 STOP. This procedure is complete.

Procedure 4-11 WiFi 2.4G networking

1 Select Network > WiFi 2.4G from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-11.

configuration

Figure 4-11 WiFi 2.4G network window

Table 4-10 describes the fields in the WiFi 2.4G network window.

4-16 Alcatel-Lucent 7368 ISAM ONT

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Enable

Select this checkbox to enable WiFi

Mode

Choose a wi-fi mode from the drop-down menu:

• auto (b/g/n)

• b

• g

• n

• b/g

Channel

Choose a channel from the drop-down menu or choose Auto to have the
channel automatically assigned

Bandwidth

Choose 20 MHz or 40 MHz from the drop-down menu.

Transmitting
Power

Choose the percentage transmitting power from the drop-down menu
SSID Select

Choose the SSID from the drop-down menu

SSID Name

Enter the SSID name

Enable SSID

Enable or disable SSID from this drop-down menu

SSID Broadcast

Enable or disable SSID broadcast from this drop-down menu

Port Mode

Choose a port mode from the drop-down menu:

• Route

• Bridge

Encrypt Mode

Choose an encryption mode from the drop-down menu:

• OPEN

• WEP

• WPA/WPA2 Personal

• WPA/WPA2 Enterprise

WPA Version

Choose a WPA version from the drop-down menu:

• WPA1

• WPA2

• WPA1/WPA2

WPA Encryption
Mode

Choose a WPA encryption mode from the drop-down menu:

• TKIP

• AES

• TKIP/AES

WPA Key

Enter the WPA key

Enable WPS

Enable or disable WPS from this drop-down menu

4 — Configure a G-240W-B indoor ONT

Table 4-10 WiFi 2.4G network parameters

2 Configure the WiFi connection.

3 If you have enabled and configured WPS, click WPS connect.

4 Click Save.

Alcatel-Lucent 7368 ISAM ONT 4-17
Edition 01
G-240W-B Product Guide

5 STOP. This procedure is complete.

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Enable

Select this checkbox to enable WiFi

Channel

Choose a channel from the drop-down menu or choose Auto to have the
channel automatically assigned

Bandwidth

Choose 20 MHz or 40 MHz from the drop-down menu

Transmitting
Power

Choose the percentage transmitting power from the drop-down menu
SSID Select

Choose the SSID from the drop-down menu

SSID Name

Enter the SSID name

Enable SSID

Enable or disable SSID from this drop-down menu

SSID Broadcast

Enable or disable SSID broadcast from this drop-down menu

4 — Configure a G-240W-B indoor ONT

Procedure 4-12 WiFi 5G networking configuration

1 Select Network > WiFi 5G from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-12.

Figure 4-12 WiFi 5G network window

Table 4-11 describes the fields in the WiFi 5G network window.

(1 of 2)

4-18 Alcatel-Lucent 7368 ISAM ONT

Table 4-11 WiFi 5G network parameters

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Encrypt Mode

Choose an encryption mode from the drop-down menu:

• OPEN

• WEP

• WPA/WPA2 Personal

• WPA/WPA2 Enterprise

WPA Key

Enter the WPA key

Enable WPS

Enable or disable WPS from this drop-down menu

4 — Configure a G-240W-B indoor ONT

(2 of 2)

2 Configure the WiFi connection.

3 If you have enabled and configured WPS, click WPS connect.

4 Click Save.

5 STOP. This procedure is complete.

Procedure 4-13 Routing configuration

1 Select Network > Routing from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-13.

Figure 4-13 Routing network window

Table 4-12 describes the fields in the Routing network window.

Alcatel-Lucent 7368 ISAM ONT 4-19
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Enable Routing

Select this checkbox to enable routing

Destination IP
Address

Enter the destination IP address

Destination
Netmask

Enter the destination network mask
Gateway

Enter the gateway address

IPv4 Interface

Choose a WAN connection previously created in the WAN network window
from the drop-down menu

4 — Configure a G-240W-B indoor ONT

2 Enter the routing information.

3 Click Add.

4 STOP. This procedure is complete.

Procedure 4-14 DNS configuration

1 Select Network > DNS from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-14.

Table 4-12 Routing network parameters

Figure 4-14 DNS network window

Table 4-13 describes the fields in the DNS network window.

4-20 Alcatel-Lucent 7368 ISAM ONT

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Domain Name

Domain name

IPv4 Address

Domain IP address

Origin Domain

Origin domain name

New Domain

New domain name

Field

Description

Periodic Inform
Enable

Select this checkbox to enable periodic inform updates

4 — Configure a G-240W-B indoor ONT

Table 4-13 DNS network parameters

2 Enter the domain name and IP address and click Add.

3 If required, associate an origin domain with a new domain, click Add.

4 STOP. This procedure is complete.

Procedure 4-15 TR-069 configuration

1 Select Network > TR-069 from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-15.

Figure 4-15 TR-069 network window

Table 4-14 describes the fields in the TR-069 network window.

(1 of 2)

Alcatel-Lucent 7368 ISAM ONT 4-21
Edition 01
G-240W-B Product Guide

Table 4-14 TR-069 network parameters

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Periodic Inform
Interval(s)

Time between periodic inform updates, in seconds
URL

URL of the auto-configuration server

Username

Username used to log in to the ONT

Password

Password used to log in to the ONT

Connect Request
Username

Username used to log in to the auto-configuration server

Connect Request
Password

Password used to log in to the auto-configuration server

4 — Configure a G-240W-B indoor ONT

(2 of 2)

2 Configure TR-069 by entering the required information.

3 Click Save.

4 STOP. This procedure is complete.

Security configuration

• firewall

• MAC filter

• IP filter

G-240W-B ONT also supports security configuration, including:

4-22 Alcatel-Lucent 7368 ISAM ONT

• DMZ and ALG

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Security level

Choose the security level from the drop-down menu

Attack Protect

Enable or disable attack protect from the drop-down menu

4 — Configure a G-240W-B indoor ONT

Procedure 4-16 Firewall configuration

1 Select Security > Firewall from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-16.

Figure 4-16 Firewall window

Table 4-15 describes the fields in the firewall window.

Table 4-15 Firewall parameters

2 Configure the firewall.

3 Click Save.

4 STOP. This procedure is complete.

Alcatel-Lucent 7368 ISAM ONT 4-23
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Enable MAC filter

Select this checkbox to enable the MAC filter

Mac Address

MAC address

Mac Filter Mode

Choose the MAC filter mode from this drop-down menu

4 — Configure a G-240W-B indoor ONT

Procedure 4-17 MAC filter configuration

1 Select Security > Mac Filter from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-17.

Figure 4-17 MAC filter window

Table 4-16 describes the fields in the MAC filter window.

Table 4-16 MAC filter parameters

2 Configure a MAC filter.

3 Click Add.

4 STOP. This procedure is complete.

4-24 Alcatel-Lucent 7368 ISAM ONT

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Enable IP Filter

Select this checkbox to enable an IP filter

Mode

Choose an IP filter mode from the drop-down menu:

• Drop for upstream

• Drop for downstream

Internal Client

Choose an internal client from the drop-down menu:

• Customer setting - uses the IP address input below

• IP - uses the connecting devices' IP to the ONT

Local IP Address

Local IP address

Source Subnet
Mask

Source subnet mask
Remote IP Address

Remote IP address

Destination

Subnet

Mask

Destination subnet mask
Protocol

Choose an application protocol or all from the drop-down menu

4 — Configure a G-240W-B indoor ONT

Procedure 4-18 IP filter configuration

1 Select Security > IP filter from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-18.

Figure 4-18 IP filter window

Table 4-17 describes the fields in the IP filter window.

Alcatel-Lucent 7368 ISAM ONT 4-25
Edition 01
G-240W-B Product Guide

2 Configure the IP filter.

Table 4-17 IP filter parameters

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

ALG Config

Select the checkboxes to enable the protocols to be supported by the ALG

DMZ Config

WAN Connection
List

Choose a WAN connection from the drop-down menu
Enable DMZ

Select this checkbox to enable DMZ on the chosen WAN connection

DMZ IP Address

Choose Customer Setting and enter the DMZ IP address or choose the IP
address of a connected device from the drop-down menu

4 — Configure a G-240W-B indoor ONT

3 Click Add.

4 STOP. This procedure is complete.

Procedure 4-19 DMZ and ALG configuration

1 Select Security > DMZ and ALG from the top-level menu in the GPON Home

Gateway window, as shown in Figure 4-19.

Figure 4-19 DMZ and ALG window

Table 4-18 describes the fields in the DMZ and ALG window.

2 Configure ALG.

3 Click Save ALG.

4 Configure DMZ.

4-26 Alcatel-Lucent 7368 ISAM ONT

Table 4-18 DMZ and ALG parameters

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

APPName

Choose an application name from the drop-down menu

WAN Port

WAN port range

LAN Port

LAN port range

Internal Client

Choose a connected device from the drop-down menu and enter the
associated IP address

4 — Configure a G-240W-B indoor ONT

5 Click Save DMZ.

6 STOP. This procedure is complete.

Application configuration

G-240W-B ONT also supports application configuration, including:

• port forwarding

• DDNS

• NTP

• USB storage

Procedure 4-20 Port forwarding configuration

1 Select Application > Port forwarding from the top-level menu in the GPON

Gateway window, as shown in Figure 4-20.

Figure 4-20 Port forwarding window

Home

Table 4-19 describes the fields in the port forwarding window.

(1 of 2)

Alcatel-Lucent 7368 ISAM ONT 4-27
Edition 01
G-240W-B Product Guide

Table 4-19 Port forwarding parameters

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Protocol

Choose the port forwarding protocol from the drop-down menu:

• TCP

• UDP

• TCP/UDP

Enable Mapping

Select this checkbox to enable mapping

WAN Connection
List

Choose a WAN connection from the drop-down menu

Field

Description

WAN Connection
List

Choose a WAN connection from the drop-down menu

4 — Configure a G-240W-B indoor ONT

(2 of 2)

2 Configure port forwarding.

3 Click Add.

4 STOP. This procedure is complete.

Procedure 4-21 DDNS configuration

1 Select Application > DDNS from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-21.

Figure 4-21 DDNS window

Table 4-20 describes the fields in the DDNS window.

4-28 Alcatel-Lucent 7368 ISAM ONT

(1 of 2)

Table 4-20 DDNS parameters

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Enable DDNS

Select this checkbox to enable DDNS on the chosen WAN connection

ISP

Choose an ISP from the drop-down menu.

Domain Name

Domain name

Username

Username

Password

Password

Field

Description

Enable NTP Service

Select this checkbox to enable NTP service

Current Time

Enter the current local date and time

First Time Server

Choose a time server from the drop-down menu or choose Customer setting
and enter the address of the time server.

4 — Configure a G-240W-B indoor ONT

(2 of 2)

2 Configure DDNS.

3 Click Save.

4 STOP. This procedure is complete.

Procedure 4-22 NTP configuration

1 Select Application > NTP from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-22.

Figure 4-22 NTP window

Table 4-21 describes the fields in the NTP window.

Alcatel-Lucent 7368 ISAM ONT 4-29
Edition 01
G-240W-B Product Guide

(1 of 2)

Table 4-21 NTP parameters

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Second Time
Server

Choose a time server from the drop-down menu or choose Customer setting
and enter the address of the time server.

Interval Time

Interval at which to get the time from the time server, in seconds

Time Zone

Choose the local time zone from the drop-down menu

Field

Description

Enable FTP server

Select this checkbox to enable using an FTP server for data storage

Username

Username for FTP server

Password

Password for FTP server

Re-enter Password

Password for FTP server

4 — Configure a G-240W-B indoor ONT

(2 of 2)

2 Configure NTP.

3 Click Save.

4 STOP. This procedure is complete.

Procedure 4-23 USB storage configuration

1 Select Application > USB storage from the top-level menu in the GPON Home

Gateway window, as shown in Figure 4-23.

Figure 4-23 USB storage window

Table 4-22 describes the fields in the USB storage window.

4-30 Alcatel-Lucent 7368 ISAM ONT

Table 4-22 USB storage parameters

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

4 — Configure a G-240W-B indoor ONT

2 Configure USB storage.

3 Click Save.

4 STOP. This procedure is complete.

Maintenance

G-240W-B ONT also supports maintenance tasks, including:

• password change

• SLID configuration

• device management

• backup and restore

• firmware upgrade

• device reboot

• restore factory defaults

• diagnose

• log

Procedure 4-24 Password configuration

1 Select Maintain > Password from the top-level menu in the GPON Home Gateway

window, as shown in Figure 4-24.

Figure 4-24 Password window

Table 4-23 describes the fields in the password window.

Alcatel-Lucent 7368 ISAM ONT 4-31
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

New Password

New password

Re-enter password

Password must match password entered above

Prompt message

Password prompt message

Field

Description

Current SLID

Displays current SLID

Input new SLID

Enter new SLID

SLID Mode

Choose a SLID mode from the drop-down menu.

4 — Configure a G-240W-B indoor ONT

2 Configure the new password.

3 Click Save.

4 STOP. This procedure is complete.

Procedure 4-25 SLID configuration

1 Select Maintain > SLID Configuration from the top-level menu in the GPON

Gateway window, as shown in Figure 4-25.

Table 4-23 Password parameters

Figure 4-25 SLID configuration window

Home

Table 4-24 describes the fields in the SLID configuration window.

4-32 Alcatel-Lucent 7368 ISAM ONT

Table 4-24 SLID configuration parameters

Edition 01

G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

Field

Description

Host name

Choose a host from the drop-down menu

Alias

Enter an alias for the chosen host

4 — Configure a G-240W-B indoor ONT

2 Configure the new SLID.

3 Click Save.

4 STOP. This procedure is complete.

Procedure 4-26 Device management

1 Select Maintain > Device Management from the top-level menu in the GPON Home

Gateway window, as shown in Figure 4-26.

Figure 4-26 Device management window

Table 4-25 describes the fields in the Device management window.

Table 4-25 Device management parameters

2 Configure an alias for a specific host.

3 Click Add.

4 STOP. This procedure is complete.

Alcatel-Lucent 7368 ISAM ONT 4-33
Edition 01
G-240W-B Product Guide

R05.01.01 | December 2014 | 3FE-56678-AAAA-TCZZA | Edition 01

4 — Configure a G-240W-B indoor ONT

Procedure 4-27 Backup and restore

1 Select Maintain > Backup and Restore from the top-level menu in the GPON Home

Gateway window, as shown in Figure 4-27.

Figure 4-27 Backup and Restore window

2 Click Select File and choose the backup file.

3 Click Import Config File to restore the ONT to the saved backup or click Export

Config File to export the current ONT configuration to the backup file.

4 STOP. This procedure is complete.

Procedure 4-28 Upgrade firmware

1 Select Maintain > Firmware Upgrade from the top-level menu in the GPON Home

Gateway window, as shown in Figure

Figure 4-28 Firmware upgrade window

4-28.

2 Click Select File and choose the firmware file.

4-34 Alcatel-Lucent 7368 ISAM ONT

Edition 01

G-240W-B Product Guide